2004 Civic 3-Door Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ......................................................................................................................................... i A Few Words About Safety..........................................................................
Table of Contents Owner’s Identification . This Owner’s Manual should be considered a permanent part of the vehicle and should remain with the vehicle when it is sold. OWNER This Owner’s Manual covers all models of the Civic Hatchback. You may find . descriptions of equipment and features that are not on your particular model. ADDRESS STREET CITY STATE/PROVINCE . ZIP CODE/ POSTAL CODE V. I. N.
Table of Contents Introduction Congratulations! Your selection of a 2005 Honda Civic was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your vehicle so you can refer to it at any time. As you read this manual, you will find information that is preceded by a symbol.
Table of Contents A Few Words About Safety Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
Table of Contents Your Vehicle at a Glance INSTRUMENT PANEL (P. 51) GAUGES (P. 57) AIRBAGS (P. 11, 23) POWER DOOR LOCK SWITCH (P. 67) POWER WINDOW SWITCHES (P. 76) HOOD RELEASE HANDLE (P. 112) AUDIO SYSTEM (P. 90) FUEL FILL DOOR RELEASE (P. 111) 4 HEATING/ COOLING CONTROLS (P. 86) M/T (P.
Table of Contents Your Vehicle at a Glance HAZARD WARNING BUTTON (P. 62) Your Vehicle at a Glance WINDSHIELD WIPERS/WASHERS (P. 60) HEADLIGHTS/ TURN SIGNALS (P. 61) REAR WINDOW DEFOGGER (P. 62) CRUISE CONTROL MASTER SWITCH (P. 105) MIRROR CONTROLS (P. 79) HORN TILT ADJUSTMENT (P. 63) CRUISE CONTROL BUTTONS (P. 105) : To use the horn, press the center pad of the steering wheel.
Table of Contents 6
Table of Contents Driver and Passenger Safety Important Safety Precautions .......... 8 Your Vehicle’s Safety Features........ 9 Seat Belts ...................................... 10 Airbags .......................................... 11 Protecting Adults and Teens.......... 12 1. Close and Lock the Doors ...... 12 2. Adjust the Front Seats ............ 12 3. Adjust the Seat-Backs ............. 14 4. Adjust the Head Restraints .... 15 5. Fasten and Position the Seat Belts ..............................
Table of Contents Table of Contents Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags are designed to supplement seat belts, not replace them.
Table of Contents Table of Contents Your Vehicle’s Safety Features (8) (1) (3) (4) (6) (7) (5) (2) (8) (9) (7) (10) (2) (1) Safety Cage (2) Crush Zones (3) Seats and Seat-Backs (4) Head Restraints (5) Collapsible Steering Column (6) Seat Belts (7) Front Airbags (8) Side Airbags (Optional) (9) Seat Belt Tensioners (10) Seat Belt Buckle Tensioners Some features do not require any action on your part.
Table of Contents Table of Contents Your Vehicle’s Safety Features Seat Belts Your vehicle is equipped with seat belts in all seating positions. Your seat belt system also includes an indicator on the instrument panel to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.
Table of Contents Table of Contents Your Vehicle’s Safety Features The most important things you need to know about your airbags are: Airbags Airbags offer no protection in rear impacts, or minor frontal or side collisions. Airbags can pose hazards.
Table of Contents Table of Contents Protecting Adults and Teens The rest of this section gives more detailed information about how you can maximize your safety. Remember however, that no safety system can prevent all injures or deaths that can occur in a severe crash, even where seat belts are properly worn and the airbags deploy.
Table of Contents Table of Contents Protecting Adults and Teens If you cannot get far enough away from the steering wheel and still reach the controls, we recommend that you investigate whether some type of adaptive equipment may help. Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate. Once your seat is adjusted correctly, rock it back and forth to make sure the seat is locked in position.
Table of Contents Table of Contents Protecting Adults and Teens 3.Adjust the Seat-Backs Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant’s chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury. Reclining the seat-back too far can result in serious injury or death in a crash.
Table of Contents Table of Contents Protecting Adults and Teens 4.Adjust the Head Restraints Make sure head restraints are in place and positioned properly before driving. Have passengers with adjustable head restraints adjust their restraint so the back of their head rests against the center of the restraint. Taller persons should adjust their restraint as high as possible. Properly adjusted head restraints will help protect occupants from whiplash and other crash injuries.
Table of Contents Table of Contents Protecting Adults and Teens Improperly positioning the seat belts can cause serious injury or death in a crash. RELEASE BUTTON Make sure all seat belts are properly positioned before driving. Position the lap part of the belt as low as possible across your hips, then pull up on the shoulder part of the belt so the lap part fits snugly. This lets your strong pelvic bones take the force of a crash and reduces the chance of internal injuries.
Table of Contents Table of Contents Protecting Adults and Teens Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause If a seat belt does not seem to work properly, it may not protect the occupant in a crash. Sitting improperly can increase the chance of injury during a crash.
Table of Contents Table of Contents Protecting Adults and Teens In addition, an occupant who is out of position in the front seat can be seriously or fatally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag. Advice for Pregnant Women This will reduce the risk of injuries to both you and your unborn child that can be caused by a crash or an inflating front airbag.
Table of Contents Table of Contents Protecting Adults and Teens Additional Safety Precautions Two people should never use the same seat belt. If they do, they Do not put any accessories on seat belts. Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can reduce the protective capability of the belt and increase the chance of serious injury in a crash. Never let passengers ride in the cargo area or on top of a foldeddown back seat.
Table of Contents Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The front seat belts are also equipped with automatic seat belt tensioners. The seat belt system includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts.
Table of Contents Table of Contents Additional Information About Your Seat Belts Automatic Seat Belt Tensioners The tensioners are designed to activate primarily in frontal collisions, and they should activate in any collision severe enough to cause front-airbag inflation. The tensioners can also be activated during a collision in which the front airbags do not deploy. In this case, the airbags would not be needed, but the additional restraint could be helpful.
Table of Contents Table of Contents Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the belts retract easily. Any belt that is not in good condition or working properly will not provide good protection and should be replaced as soon as possible. Honda provides a lifetime warranty on seat belts for U.S.
Table of Contents Table of Contents Additional Information About Your Airbags Airbag System Components Your Airbag System includes: In models with side airbags, one for the driver and one for a front passenger. The airbags are stored in the outer edges of the seatbacks. Both are marked ‘‘SIDE AIRBAG’’ (see page 26 ). Automatic seat belt tensioners (see page 21 ).
Table of Contents Table of Contents Additional Information About Your Airbags How Your Front Airbags Work During a frontal crash, your seat belt restrains your lower body and torso, and the airbag helps protect your head and chest. Although both airbags normally inflate within a split second of each other, it is possible for only one airbag to deploy. If you ever have a moderate to severe frontal collision, sensors will detect the vehicle’s rapid deceleration.
Table of Contents Table of Contents Additional Information About Your Airbags After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the vehicle as soon as it is safe to do so. Dual-Stage Airbags Dual-Threshold Airbags Your front airbags are dual-stage airbags.
Table of Contents Table of Contents Additional Information About Your Airbags How Your Side Airbags Work is no passenger. To reduce the risk of injury from an inflating side airbag, your vehicle has an automatic cutoff system for the passenger’s side airbag. If the Side Airbag Off Indicator comes on (see page 27 ), have the passenger sit upright. Once the passenger is out of the airbag’s deployment path, the system will turn the airbag back on, and the indicator will go out.
Table of Contents Table of Contents Additional Information About Your Airbags When you turn the ignition to ON (II), this indicator will come on briefly then go out. This tells you the system is working properly. If the indicator comes on at any other time, or does not come on at all, you should have the system checked by your dealer. For example: If the SRS indicator does not come on after you turn the ignition to ON (II).
Table of Contents Table of Contents Additional Information About Your Airbags Airbag Service Your airbag systems are virtually maintenance free, and there are no parts you can safely service. However, you must have your vehicle serviced if: An airbag ever inflates. Any airbag that has deployed must be replaced along with the control unit and other related parts. If a front airbag inflates, the seat belt tensioners must also be replaced. Do not try to remove or replace any airbag by yourself.
Table of Contents Table of Contents Protecting Children Children depend on adults to protect them. However, despite their best intentions many adults do not know how to properly protect child passengers. If you have children, or ever need to drive with a child in your vehicle, be sure to read this section. It begins with important general guidelines, then presents special information for infants, small children, and larger children.
Table of Contents Table of Contents Protecting Children General Guidelines All Children Should Sit in the Back Seat According to accident statistics, children of all ages and sizes are safer when they are restrained in a back seat. The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in a back seat. Some states have lows restricting where children may ride.
Table of Contents Table of Contents Protecting Children Canadian Models Driver and Passenger Safety To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the dashboard (U.S. models) and on the front visors. Please read and follow the instructions on these labels. General Guidelines U.S.
Table of Contents Table of Contents Protecting Children General Guidelines If You Must Drive with Several Children Your vehicle has a back seat where children can be properly restrained. If you ever have to carry a group of children, and a child must ride in front: Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page 43 ). Move the vehicle seat as far to the rear as possible (see page 12 ).
Table of Contents Table of Contents Protecting Children Additional Safety Precautions Never hold an infant or child on your lap. If you are not wearing a Never put a seat belt over yourself and a child. During a crash, the adult supervision is illegal in most states and Canadian provinces, and can be very hazardous. For example, infants and small children left in a vehicle on a hot day can die from heatstroke.
Table of Contents Table of Contents Protecting Infants and Small Children Protecting Infants Child Seat Placement Placing a rear-facing child seat in the front seat can result in serious injury or death if the passenger’s front airbag inflates. Always place a rear-facing child seat in the back seat, not the front.
Table of Contents Table of Contents Protecting Infants and Small Children Protecting Small Children Child Seat Placement Placing a forward-facing child seat in the front seat of a vehicle equipped with a passenger’s airbag can be hazardous. If the vehicle seat is too far forward, or the child’s head is thrown forward during a collision, an inflating airbag can strike the child with enough force to cause very serious or fatal injuries.
Table of Contents Table of Contents Selecting a Child Seat Selecting a Child Seat When buying a child seat, you need to choose either a conventional child seat, or one designed for use with the Lower Anchors and Tethers for Children (LATCH) system. Conventional child seats must be secured to a vehicle with a seat belt, whereas LATCH-compatible seats are secured by attaching the seat to hardware built into the two outer second row seats.
Table of Contents Table of Contents Installing a Child Seat 1. Properly secure the child seat to the vehicle. All child seats must be secured to the vehicle with the lap part of a lap/shoulder belt or with the LATCH (Lower Anchors and Tethers for Children) system. A child whose seat is not properly secured to the vehicle can be endangered in a crash. A child seat secured with a seat belt should be installed as firmly as possible. However, it does not need to be ‘‘rock solid.
Table of Contents Table of Contents Installing a Child Seat Installing a Child Seat Using LATCH Your vehicle is equipped with LATCH (Lower Anchors and Tethers for Children) at the outer rear seats. The lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH. The location of each lower anchor is indicated by a small button above the anchor point. LOWER ANCHORS To install a LATCH-compatible child seat: 1.
Table of Contents Table of Contents Installing a Child Seat TETHER STRAP HOOK Other LATCH-compatible seats have a flexible-type connector as shown above. 4. Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit. Driver and Passenger Safety Flexible type 7. Push and pull the child seat forward and from side to side to verify that it is secure. ANCHOR 5.
Table of Contents Table of Contents Installing a Child Seat Installing a Child Seat with a Lap/ Shoulder Belt When not using the LATCH system, all child seats must be secured to the vehicle with the lap part of a lap/ shoulder belt. In addition, the lap/shoulder belts in all seating positions except the driver’s have a locking mechanism that must be activated to secure a child seat. 1.
Table of Contents Table of Contents Installing a Child Seat 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked, and you will need to repeat these steps. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Table of Contents Table of Contents Installing a Child Seat Installing a Child Seat with a Tether TETHER ANCHOR POINTS One tether anchor point for each of the outer rear seats is located under the cargo floor carpet and the tailgate sill. Pull up the carpet to access the anchor point (outboard anchor) when securing a tether-style child seat to the vehicle.
Table of Contents Table of Contents Installing a Child Seat, Protecting Larger Children Using the Center Anchor The following pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions for a child who must sit in front. Allowing a larger child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.
Table of Contents Table of Contents Protecting Larger Children Checking Seat Belt Fit 3. Does the shoulder belt cross between the child’s neck and arm? Using a Booster Seat 4. Is the lap part of the belt as low as possible, touching the child’s thighs? 5. Will the child be able to stay seated like this for the whole trip? To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt, then ask yourself: 1. Does the child sit all the way back against the seat? 2.
Table of Contents Table of Contents Protecting Larger Children Booster seats can be high-back or low-back. Whichever style you select, make sure the booster meets federal safety standards (see page 36 ) and that you follow the booster seat maker’s instructions. If a child who uses a booster seat must ride in front, move the vehicle seat as far to the rear as possible, and be sure the child is wearing the seat belt properly.
Table of Contents Table of Contents Protecting Larger Children Of course, children vary widely. And while age may be one indicator of when a child can safely ride in the front, there are other important factors you should consider. If you decide that a child can safely ride up front, be sure to: Additional Safety Precautions Do not let a child wear a seat belt across the neck.
Table of Contents Table of Contents Carbon Monoxide Hazard Have the exhaust system inspected for leaks whenever: Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide. The vehicle is raised for an oil change. You notice a change in the sound of the exhaust. The vehicle was in an accident that may have damaged the underside.
Table of Contents Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. If a label comes off or becomes hard to read, contact your dealer for a replacement. DASHBOARD SUN VISOR U.S. model only U.S.
Table of Contents Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach. Folding Rear Seats ...................... 73 Cargo Area Cover ............................ 75 Power Windows ............................... 76 Moonroof .......................................... 78 Mirrors .............................................. 79 Parking Brake ............................
Table of Contents Table of Contents Control Locations INSTRUMENT PANEL (P. 51) GAUGES (P. 57) HEATING/COOLING CONTROLS (P. 86) AUDIO SYSTEM (P. 90) MIRROR CONTROLS (P. 79) POWER DOOR LOCK SWITCH (P. 67) POWER WINDOW SWITCHES (P. 76) FUEL FILL DOOR RELEASE (P. 111) HOOD RELEASE HANDLE (P. 112) 50 ACCESSORY POWER SOCKET (P. 83) M/T (P.
Table of Contents Table of Contents Instrument Panel Indicators PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P. 53, 179) CRUISE CONTROL INDICATOR (P. 54) CHARGING SYSTEM INDICATOR (P. 52, 177) MAINTENANCE REQUIRED INDICATOR (P. 56) ANTI-LOCK BRAKE SYSTEM INDICATOR (P. 54) Instruments and Controls HATCH-OPEN INDICATOR (P. 53) HIGH BEAM INDICATOR (P. 53) ELECTRIC POWER STEERING INDICATOR (P. 55) LOW OIL PRESSURE INDICATOR (P. 52, 177) MALFUNCTION INDICATOR LAMP (P.
Table of Contents Table of Contents Instrument Panel Indicators The instrument panel has many indicators to give you important information about your vehicle. Malfunction Indicator Lamp See page 178 . Seat Belt Reminder Indicator This indicator comes on when you turn the ignition switch to ON (II). It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt.
Table of Contents Table of Contents Instrument Panel Indicators Parking Brake and Brake System Indicator This indicator has two functions: U.S. Canada 2. If it stays on lit after you have fully released the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For more information, see page 179 . When you press the Hazard Warning button, both turn signal indicators blink. All turn signals on the outside of the vehicle should flash.
Table of Contents Table of Contents Instrument Panel Indicators Low Fuel Indicator LOW FUEL INDICATOR Washer Level Indicator Canadian model only This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator come on (see page 142 ). Cruise Control Indicator This indicator comes on when you set the cruise control. See page 105 for information on operating the cruise control. This indicator is located in the fuel gauge.
Table of Contents Table of Contents Instrument Panel Indicators Immobilizer System Indicator This indicator comes on for a few seconds when you turn the ignition switch to ON (II). It will then go off if you have inserted a properly-coded ignition key. If it is not a properlycoded key, the indicator will blink, and the engine will not start (see page 65 ).
Table of Contents Table of Contents Instrument Panel Indicators Maintenance Required Indicator This indicator reminds you that it is time to take your vehicle in for scheduled maintenance. If you exceed 10,000 miles (16,000 km) without having the scheduled maintenance performed, this indicator will remain on as a constant reminder. Refer to the Maintenance Schedules for Normal and Severe Driving Conditions on pages 133 and 134 .
Table of Contents Table of Contents Gauges TACHOMETER SPEEDOMETER TEMPERATURE GAUGE There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances. ODOMETER/ TRIP METER SELECT/RESET BUTTON FUEL GAUGE U.S. model shown Odometer/Trip Meter The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S.
Table of Contents Table of Contents Gauges Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise to about the middle of the gauge. In severe driving conditions, the pointer may rise to the upper zone. If it reaches the red (Hot) mark, pull safely to the side of the road. Turn to page 174 for instructions and precautions on checking the engine’s cooling system.
Table of Contents Table of Contents Controls Near the Steering Wheel HEADLIGHTS/TURN SIGNALS (P. 61) WINDSHIELD WIPERS/WASHERS (P. 60) REAR WINDOW DEFOGGER (P. 62) Instruments and Controls CRUISE CONTROL MASTER SWITCH (P. 105) CRUISE CONTROL BUTTONS (P. 105) HORN MIRROR CONTROLS (P. 79) TILT ADJUSTMENT (P. 63) HAZARD WARNING BUTTON (P. 62) To use the horn, press the pad around the ‘‘H’’ logo.
Table of Contents Table of Contents Windshield Wipers and Washers Push the right lever up or down to select a position. Rear Window Wiper and Washer MIST The wipers run at high speed until you release the lever. OFF The wipers are not activated. INT The wipers operate every few seconds. In low speed and high speed, the wipers run continuously. 1. MIST 2. OFF Intermittent 3. INT 4. LO Low speed 5. HI High speed 6. Windshield Washers 60 LO The wipers run at low speed.
Table of Contents Table of Contents Turn Signal and Headlights Turn Signal and Headlights Headlights Turning the switch to the ‘‘ ’’ position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the ‘‘ ’’ position turns on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder tone when you open the driver’s door.
Table of Contents Table of Contents Instrument Panel Brightness, Hazard Warning Button, Rear Window Defogger Instrument Panel Brightness Hazard Warning Button Rear Window Defogger The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness. Push the red button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash.
Table of Contents Table of Contents Rear Window Defogger, Steering Wheel Adjustment Make sure the rear window is clear and you have good visibility before starting to drive. Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash. Adjust the steering wheel only when the vehicle is stopped. To adjust the steering wheel upward or downward: 2. Move the steering wheel up or down to the desired position.
Table of Contents Table of Contents Keys and Locks KEY NUMBER TAG MASTER KEYS (Black) VALET KEY (Gray) You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks. These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged. Protect the keys from direct sunlight, high temperature, and high humidity.
Table of Contents Table of Contents Immobilizer System The Immobilizer System protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine will not start. The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable.
Table of Contents Table of Contents Ignition Switch If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key. ACCESSORY (I) You can operate the audio system and the accessory power sockets in this position. The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). LOCK (0) You can insert or remove the key only in this position. To turn the key, push it in slightly.
Table of Contents Table of Contents Door Locks Power Door Locks Hatch LOCK TAB Unlock Lock Lock MASTER DOOR LOCK SWITCH Each door has a lock tab on the top. When you push down the lock tab on the driver’s door, both doors and the hatch lock. When you push down the lock tab on the passenger’s door, only that door locks. All doors lock when you push down the lock tab on the driver’s door, or lock the driver’s door from the outside with the key.
Table of Contents Table of Contents Door Locks HATCH HANDLE HANDLE To open the hatch, pull the handle, then lift up. To close the hatch, use the hatch handle to lower the hatch, then press down on the back edge. Keep the hatch closed at all times while driving to avoid damaging it and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 47 .
Table of Contents Table of Contents Remote Transmitter LED LOCK BUTTON PANIC BUTTON LOCK Press this button once to lock both doors and hatch. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked. You cannot lock it if any door is not fully closed or the key is in the ignition switch.
Table of Contents Table of Contents Remote Transmitter Replacing the Transmitter Battery ROUND COVER CUSHION RING BATTERY If it takes several pushes on the button to lock or unlock the doors and the hatch, replace the battery as soon as possible. Battery type: CR2025 70 To replace the battery, remove the round cover on the back of the transmitter by turning it counterclockwise with a coin. Insert a new battery with the side facing up. Align the mark on the cover with the mark on the transmitter.
Table of Contents Table of Contents Seats Front Seat Adjustments See pages 12 14 for important safety information and warnings about how to properly position seats and seat-backs. To adjust the seat forward and backward, pull up on the bar under the seat cushion’s front edge. Then try to move the seat to make sure it is locked in position. To change the seat-back angle of the front seat, pull up on the lever on the outside of the seat bottom.
Table of Contents Table of Contents Seats Head Restraints See page 15 for important safety information and a warning about how to properly position the head restraints. The head restraints help protect you and your passengers from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint. Rear Seat Access The head restraints in the rear outboard seating positions adjust for height.
Table of Contents Table of Contents Seats After you return the seat-back to the upright position, push the whole seat backwards until it latches. Make sure the seat is fully latched before you sit in it. CLIP Before folding down the seat-back, move the seat belt out of the way and put the shoulder part of the outside seat belt in the clip on each side. 73 Instruments and Controls Folding Rear Seat The back of the rear seat folds down to give you more cargo space. Each side folds down separately.
Table of Contents Table of Contents Seats RELEASE LEVER Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have to brake hard. See Carrying Cargo on page 117 . To lock the seat-back upright, push it firmly against its latch. Tug on the seat-back to make sure it is latched. To unlatch either side of the seatback, pull up on the release lever, then fold the seat-back down.
Table of Contents Table of Contents Cargo Area Cover HOOK NOTCHES To remove the cargo area cover, disconnect the cables from the hatch by lifting up each end, then pulling it outward. Then push up on the underside of the cargo cover at each front corner to unsnap it from the body. Instruments and Controls The cargo area cover may be removed to give you more cargo room. To install the cargo area cover, place it in its normal position over the cargo area.
Table of Contents Table of Contents Power Windows Your vehicle’s windows are electrically-powered. Turn the ignition switch to ON (II) to raise or lower any window. Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it. DRIVER’S WINDOW SWITCH Closing a power window on someone’s hands or fingers can cause serious injury.
Table of Contents Table of Contents Power Windows If the MAIN switch is OFF, the passenger window cannot be raised or lowered. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the window unintentionally. AUTO REVERSE If the driver’s window senses any obstacle while it is closing automatically, it will reverse direction and then stop. To close the window, remove the obstacle, then use the window switch again.
Table of Contents Table of Contents Moonroof OPEN/CLOSE SWITCH To open the moonroof, pull back the moonroof switch firmly. To close the moonroof fully, push the switch forward. To tilt the moonroof up, press the button in. To close it, push the switch forward. TILT-UP BUTTON There are two switches on the ceiling near the front ceiling light. The ignition switch must be in the ON (II) position to operate the moonroof. 78 The moonroof will not close completely; it will stop about 5.
Table of Contents Table of Contents Mirrors Mirrors Adjusting the Power Mirrors 2. Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down. TAB Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. ADJUSTMENT SWITCH SELECTOR SWITCH 1. Move the selector switch to L (driver’s side) or R (passenger’s side). The inside mirror has day and night positions.
Table of Contents Table of Contents Mirrors, Parking Brake Power Mirror Heaters HEATED MIRROR BUTTON Canadian model only The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off. 80 Parking Brake PARKING BRAKE LEVER To apply the parking brake, pull the lever up fully.
Table of Contents Table of Contents Interior Lights Ceiling Light FRONT DOOR ACTIVATED The front ceiling light also contains two spotlights. Push the button next to the light to turn it on and off. Cargo Area Light The cargo area light comes on when you open the hatch. OFF Instruments and Controls ON The ceiling light has a three-position switch: ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you: Open any door. Remove the key from the ignition.
Table of Contents Table of Contents Interior Convenience Items COAT HOOK BEVERAGE HOLDER VANITY MIRROR DRIVER’S POCKET ACCESSORY POWER SOCKET GLOVE BOX BEVERAGE HOLDER CONSOLE COMPARTMENT 82 BEVERAGE HOLDER
Table of Contents Table of Contents Interior Convenience Items Accessory Power Socket This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps). It will not power an automotive type cigarette lighter element. Glove Box Open the glove box by squeezing the handle. Close it with a firm push. Console Compartment CONSOLE COMPARTMENT An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.
Table of Contents 84
Table of Contents Features The heating and air conditioning systems in your vehicle provide a comfortable driving environment in all weather conditions. Your vehicle has an anti-theft audio system that requires a code number to enable it. 85 Features The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) Vents, Heating, and A/C ................
Table of Contents Table of Contents Vents, Heating, and A/C RECIRCULATION BUTTON AIR CONDITIONING (A/C) BUTTON MODE CONTROL DIAL TEMPERATURE CONTROL DIAL FAN CONTROL DIAL 86 REAR WINDOW DEFOGGER BUTTON
Table of Contents Table of Contents Air Flow Controls Fan Control Dial Turn this dial to increase or decrease the fan speed and airflow. Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow. Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent throughout the system again. When the indicator is off, air is brought in from the outside of the vehicle (Fresh Air mode).
Table of Contents Table of Contents Vents, Heating, and A/C Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the rear side panels. 1. Set the temperature to the lower limit. 2. Make sure the A/C is off. and Fresh Air mode. 3. Select 4. Set the fan to the desired speed. Using the Heater The heater uses engine coolant to warm the air.
Table of Contents Table of Contents Vents, Heating, and A/C Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C). 1. Set the fan to high. . The system 2. Select automatically switches to fresh air mode and turns on the A/C. The A/C indicator will not come on in U.S. vehicles. 3.
Table of Contents Table of Contents Playing the Radio STEREO INDICATOR AM/FM BUTTON SCAN INDICATOR AUTO SELECT BUTTON SCAN BUTTON TUNE KNOB POWER/VOLUME KNOB SEEK BAR 90 PRESET BUTTONS
Table of Contents Table of Contents Playing the Radio To Play the Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the PWR/VOL knob or the AM/FM button. Adjust the volume by turning the PWR/VOL knob. To Select a Station You can use these five methods to find radio stations on a selected band: TUNE, SEEK, SCAN, the preset buttons, and AUTO SELECT . TUNE Use the TUNE knob to tune the radio to a desired frequency.
Table of Contents Table of Contents Playing the Radio If you are AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the Auto Select feature to find stations in the local area. Press the A. SEL button. ‘‘A.SEL’’ flashes in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM, and twelve FM stations in the preset buttons.
Table of Contents Table of Contents Radio Reception Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: FM band: 87.7 to 107.9 megahertz Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 megahertz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
Table of Contents Table of Contents Radio Reception As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter.
Table of Contents Table of Contents Playing a CD CD BUTTON REPEAT INDICATOR CD SLOT RANDOM BUTTON CD EJECT BUTTON Features POWER/VOLUME KNOB RANDOM INDICATOR SEEK/SKIP BAR SCAN/REPEAT BUTTON 95
Table of Contents Table of Contents Playing a CD, CD Changer To Play a CD With the ignition switch in the ACCESSORY (I) or ON (II) position, insert a CD into the CD slot. The drive will pull the CD in the rest of the way and begin to play it. The number of the track playing is shown in the display. The system will continuously play a CD until you change modes. SKIP Each time you press and release , the player skips forward to the beginning of the next track.
Table of Contents Table of Contents Protecting Your CDs General Information When using CD-R discs, use only high quality CDs labeled for audio use. CD-RW discs will not work in this unit. Play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems. Handle your CDs properly to prevent damage and skipping. Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit. To clean a CD, use a clean soft cloth.
Table of Contents Table of Contents CD Player Error Messages If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Cause FOCUS Error Mechanical Error High temperature 98 Solution Press the EJECT button and pull out the CD. Check if it is inserted correctly in the CD player. Make sure the CD is not scratched or damaged. Press the EJECT button and pull out the CD.
Table of Contents Table of Contents CD Changer Error Messages If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Cause FOCUS Error Mechanical Error High temperature No CD magazine in the CD changer Press the magazine eject button and pull it out. Check for an error message, and insert the magazine again.
Table of Contents Table of Contents Playing a Tape TAPE BUTTON REWIND BUTTON POWER/VOLUME KNOB SKIP BAR 100 FAST REPEAT INDICATOR FORWARD BUTTON DOLBY INDICATOR PLAY/PROGRAM BUTTON REPEAT BUTTON NR BUTTON
Table of Contents Table of Contents Playing a Tape To Play a Tape Optional on all models The tape direction indicator comes on to show you which side of the tape is playing. The indicates the side you inserted upward is now playing. If you want to play the other side, press the PLAY/PROG button. When the player reaches the end of the tape, it will automatically reverse direction and play the other side. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
Table of Contents Table of Contents Playing a Tape Press the RPT button REPEAT to continuously play a song or passage. You will see RPT displayed. The track will repeat until you press the RPT button again. NOTE: The SKIP and REPEAT functions use silent periods on the tape to find the end of a song or passage. These features may not work if there is almost no gap between selections, a high noise level, or a silent period in the middle of a selection.
Table of Contents Table of Contents Radio Theft Protection You should have received a card that lists your audio system code number and serial number. It is best to store this card in a safe place at home. In addition, you should write the audio system’s serial number in this Owner’s Manual. If you lose the card, you must obtain the code number from a dealer. To do this, you will need the system’s serial number.
Table of Contents Table of Contents Setting the Clock hour. CLOCK (SCAN/RPT) BUTTON For example: 1:06 will reset to 1:00 1:52 will reset to 2:00 HOUR BUTTON If your vehicle’s battery is disconnected or goes dead, you will need to set the clock. Press and hold the CLOCK button until you hear a beep. Change the hours by pressing the H (Preset 4) button until the numbers advance to the desired time. Change the minutes by pressing the M (Preset 5) button until the numbers advance to the desired time.
Table of Contents Table of Contents Cruise Control Using the Cruise Control CANCEL BUTTON RESUME/ accel BUTTON Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather. CRUISE CONTROL MASTER SWITCH 1. Push in the Cruise Control Master Switch. The indicator in the switch will come on. 2. Accelerate to the desired cruising speed above 25 mph (40 km/h). SET/decel BUTTON 3.
Table of Contents Table of Contents Cruise Control Cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The indicator on the instrument panel will come back on. Changing the Set Speed You can increase the set cruising speed in any of these ways: Press and hold the RESUME/ accel button.
Table of Contents Table of Contents Cruise Control Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed. Tap the brake or clutch pedal. Push the CANCEL button on the steering wheel. Push the Cruise Control Master Switch.
Table of Contents 108
Table of Contents Before Driving Break-in Period .............................. 110 Fuel Recommendations ................ 110 Service Station Procedures .......... 111 Fueling ........................................ 111 Opening and Closing the Hood ........................................ 112 Oil Check .................................... 113 Engine Coolant Check .............. 114 Fuel Economy ................................ 114 Accessories and Modifications .... 115 Carrying Cargo .....................
Table of Contents Table of Contents Break-in Period, Fuel Recommendation Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking for the first 200 miles (300 km). Do not change the oil until the scheduled maintenance time.
Table of Contents Table of Contents Service Station Procedures Fueling Pull Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. SLIT FUEL FILL CAP 1. Park with the driver’s side closest to the gas pump. 2. Open the fuel fill door by pulling on the handle to the left of the driver’s seat. 3. Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank escapes.
Table of Contents Table of Contents Service Station Procedures 5. Screw the fuel fill cap back on until it clicks at least three times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 178 ). Opening and Closing the Hood HOOD RELEASE HANDLE LATCH 6. Push the fuel fill door closed until it latches. 1. Park the vehicle, and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
Table of Contents Table of Contents Service Station Procedures Oil Check GRIP DIPSTICK CLIP SUPPORT ROD To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched. Wait a few minutes after turning the engine off before you check the oil. 1. Remove the dipstick (orange loop). 4. Remove the dipstick again and check the level.
Table of Contents Table of Contents Service Station Procedures, Fuel Economy Engine Coolant Check MAX RESERVE TANK Improving Fuel Economy Always maintain your vehicle according to the maintenance schedule. See Owner’s Maintenance Checks (see page 132 ). For example, an underinflated tire causes more ‘‘rolling resistance,’’ which uses more fuel. MIN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines.
Table of Contents Table of Contents Accessories and Modifications Modifying your vehicle, or installing some non-Honda accessories, can make it unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Although non-Honda accessories may fit on your vehicle, they may not meet factory specifications, and could adversely affect your vehicle’s handling and stability (see page 116 ).
Table of Contents Table of Contents Accessories and Modifications Modifying Your Vehicle Removing parts from your vehicle, or replacing components with non-Honda components could seriously affect your vehicle’s handling, stability, and reliability. Some examples are: Lowering your vehicle with a non-Honda suspension kit that significantly reduces ground clearance can allow the undercarriage to hit speed bumps or other raised objects, which could cause the airbags to deploy.
Table of Contents Table of Contents Carrying Cargo DOOR POCKET DRIVER’S POCKET Your vehicle has several convenient storage areas: Glove box Front door pocket Console compartment Cargo area CARGO AREA CONSOLE COMPARTMENT GLOVE BOX 117 Before Driving However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, and make it unsafe. Before carrying any type of cargo, be sure to read the following pages.
Table of Contents Table of Contents Carrying Cargo Load Limits The maximum load for your vehicle is 850 lbs (395 kg). This figure includes total weight of all occupants, cargo, and accessories. Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed. Follow all load limits and other loading guidelines in this manual. Steps for Determining Correct Load Limit: 1.
Table of Contents Table of Contents Carrying Cargo Carrying Items in the Passenger Compartment Store or secure all items that could be thrown around and hurt someone during a crash. Keep the glove box closed while driving. If it is open, a passenger could injure their knees during a crash or sudden stop. If you carry large items that prevent you from closing the hatch, exhaust gas can enter the passenger area. To avoid the possibility of carbon monoxide poisoning, follow the instructions on page 47 .
Table of Contents 120
Table of Contents Driving This section gives you tips on starting the engine under various conditions, and how to operate the manual transmission. It also includes important information on parking your vehicle, and the braking system. Preparing to Drive ......................... 122 Starting the Engine........................ 123 Manual Transmission.................... 124 Parking ............................................ 126 Towing a Trailer ............................ 126 Braking System.............
Table of Contents Table of Contents Preparing to Drive You should do the following checks and adjustments before you drive your vehicle. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 6. Check the seat adjustment (see page 71 ). 7. Check the adjustment of the inside and outside mirrors (see page 79 ). 8. Check the steering wheel adjustment (see page 63 ). 2. Check that the hood is fully closed. 3. Check that the hatch is fully closed. 9.
Table of Contents Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 6. If the engine fails to start, press the accelerator pedal all the way down and hold it there while starting to clear flooding. If the engine still does not start, return to step 5. The engine is harder to start in cold weather. Also, the thinner air f ound at altitudes above 8,000 f eet (2,400 meters) adds to this problem. 3.
Table of Contents Table of Contents Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the vehicle moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’ The manual transmission is synchronized in all forward gears for smooth operation.
Table of Contents Table of Contents Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control. The following shift points are recommended: Normal acceleration 1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 17 mph (27 km/h) 28 mph (45 km/h) 45 mph (72 km/h) 56 mph (90 km/h) Before downshifting, make sure the engine will not go into the tachometer’s red zone.
Table of Contents Table of Contents Parking, Towing a Trailer Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly or your vehicle may roll if it is parked on an incline. Parking Tips Make sure the moonroof and the windows are closed. Turn off the lights. Place any packages, valuables, etc. in the cargo area, or take them with you. Lock the doors. Never park over dry leaves, tall grass, or other flammable materials.
Table of Contents Table of Contents Braking System Check the brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious in your driving. Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, and reduces their effectiveness. It also keeps your brake lights on all the time, confusing drivers behind you.
Table of Contents Table of Contents Anti-lock Brakes (ABS) The Anti-lock Brake System (ABS) helps prevent the brakes from locking up and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it. ABS Indicator ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. You should never pump the brake pedal.
Table of Contents Maintenance This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself.
Table of Contents Table of Contents Maintenance Safety All service items not detailed in this section should be performed by a certified technician or qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required. Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off.
Table of Contents Table of Contents Maintenance Schedule The maintenance schedule assumes you will use your vehicle as normal transportation for passengers and their possessions. You should also follow these recommendations: Avoid exceeding your vehicle’s load limit. This puts excess stress on the engine, brakes, and many other vehicle parts. The load limit is shown on the tire information label on the driver’s doorjamb. Drive your vehicle regularly over a distance of several miles (kilometers).
Table of Contents Table of Contents Maintenance Schedule Servicing Your Vehicle Your authorized dealer knows your vehicle best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or skilled person to keep your warranties in effect. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record.
Table of Contents Table of Contents Follow the Normal Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule on the next page do not apply. NOTE: If you only OCCASIONALLY drive under a ‘‘severe’’ condition, you should follow the Normal Conditions Maintenance Schedule. : See information on maintenance and emissions warranty on page 132 .
Maintenance Schedule for Severe Conditions Table of Contents Table of Contents Service the items listed at the indicated distance (or time, if given).
Table of Contents Table of Contents Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 133 ) or severe conditions (page 134 ). Keep the receipts for all work done on your vehicle.
Table of Contents Table of Contents Maintenance Record (for Normal and Severe Schedules) 85,000 mi 136,000 km Signature or dealer stamp mi/km 125,000 mi 200,000 km Date 90,000 mi 144,000 km mi/km mi/km 130,000 mi 208,000 km mi/km 105,000 mi 168,000 km mi/km Date 135,000 mi 216,000 km mi/km 140,000 mi 224,000 km (or 7 years) mi/km 145,000 mi 232,000 km mi/km mi/km 150,000 mi 240,000 km 136 mi/km Date mi/km Date 155,000 mi 248,000 km Date 120,000 mi 192,000 km (or 6 years) Date Dat
Table of Contents Table of Contents Fluid Locations BRAKE FLUID (Gray cap) ENGINE OIL DIPSTICK (Orange handle) WASHER FLUID (Blue cap) CLUTCH FLUID (Gray cap) ENGINE OIL FILL CAP Maintenance ENGINE COOLANT RESERVOIR RADIATOR CAP 137
Table of Contents Table of Contents Adding Engine Oil Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20 detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. ENGINE OIL FILL CAP Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill.
Table of Contents Table of Contents Adding Engine Oil, Changing the Oil and Filter Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API Certification Seal, and it is the proper weight. You must follow the oil and filter change intervals given on the maintenance schedule. Changing the oil and filter requires special tools and access from underneath the vehicle.
Table of Contents Table of Contents Changing the Oil and Filter OIL FILTER 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: 33 lbf·ft (44 N·m , 4.5 kgf·m) 6. Refill the engine with the recommended oil. 8. Let the engine run for several minutes, then check the drain bolt and oil filter for leaks. 9. Turn off the engine, let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.
Table of Contents Table of Contents Engine Coolant Adding Engine Coolant RESERVE TANK If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
Table of Contents Table of Contents Engine Coolant, Windshield Washers RADIATOR CAP 3. The coolant level should be up to the base of the filler neck. Add coolant if it is low. Pour the coolant slowly and carefully so you do not spill. Clean up any spill immediately; it could damage components in the engine compartment. 4. Put the radiator cap back on and tighten it. 1.
Table of Contents Table of Contents Transmission Fluid Correct level FILLER BOLT The transmission should be drained and refilled with new fluid according to the time and distance recommendations in the maintenance schedule. Maintenance Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt, and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole.
Table of Contents Table of Contents Brake Fluid, Clutch Fluid Brake Fluid Check the brake fluid level in the reservoirs monthly. MAX Clutch Fluid MAX Replace the brake fluid according to the time recommendation in the maintenance schedule. Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. Using any non-Honda brake fluid can cause corrosion and decrease the life of the system.
Table of Contents Table of Contents Hood Latch, Lights Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the cargo area, readjustment may be required. Adjustments should be performed by your dealer or other qualified mechanic. Replacing a Headlight Bulb Your vehicle has halogen headlight bulbs. Handle the bulb by its plastic case and protect the glass from contact with your skin or hard objects.
Table of Contents Table of Contents Lights 3. Remove the bulb by turning it onequarter turn counterclockwise. 4. Insert the new bulb into the hole and turn it one-quarter turn clockwise to lock it in place. 5. Push the electrical connector back onto the bulb. Make sure it is on all the way. Replacing a Front Turn Signal Bulb 1. If you are changing the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, and turn off the engine.
Table of Contents Table of Contents Lights 6. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. Replacing a Side Marker Bulb 7. Test the lights to make sure the new bulb is working. SOCKET 8. Put the inner fender cover in place. Install the holding clip. Lock it in place by pushing on the center. BULB SOCKET 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 1.
Table of Contents Table of Contents Lights 2. Turn the socket one-quarter turn counterclockwise to remove it from the lens. Replacing a Front Parking Light Bulb 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. SOCKET 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 4. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 4.
Table of Contents Table of Contents Lights 4. Remove the socket for that bulb by turning it one-quarter turn counterclockwise. Replacing Rear Bulbs SOCKET 5. Remove the burned out bulb from the socket by pushing it in and turning the bulb counterclockwise until it unlocks. 6. Install the new bulb in the socket. COVER 2. Remove the cover from the inside panel by carefully prying on its upper front edge with a small flattipped screwdriver. 3.
Table of Contents Table of Contents Lights Replacing the High-mount Brake Light Bulb BULB HOLDER 1. Open the hatch. 2. Put your fingers between the interior trim and the hatch glass on either side of the high-mount brake light. Carefully pull down on the trim to unsnap the clips from the hatch. Work your way toward each end of the trim. Remove the trim. 150 3. Remove the bulb holder from the light assembly by pushing the tabs on both sides and pulling the bulb holder down. 4.
Table of Contents Table of Contents Lights 5. Push the bulb holder into the light assembly until it locks in place. 6. Test the lights to make sure the new bulb is working. Replacing a Side Turn Signal Bulb 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. SOCKET 4. Put the socket back into its hole in the lens and turn it clockwise until it locks. 7. Line up the clips on the interior trim with the corresponding holes in the hatch.
Table of Contents Table of Contents Lights 4. Turn on the parking lights and check that the new bulb is working. Replacing a Rear License Plate Bulb 5. Put the lens back on the bulb holder and push it until it latches. BULB SOCKET 1. Slide the lens to the right until the left side of the lens pops out of the body. Pull out the light assembly. 2. Remove the lens from the socket by pulling the lens while squeezing the tabs on both sides of the socket. 3. Pull the bulb straight out of its socket.
Table of Contents Table of Contents Cleaning the Seat Belts, Floor Mats, Dust and Pollen Filter Cleaning the Seat Belts Floor Mats LOOP If you use an aftermarket floor mat, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat. Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.
Table of Contents Table of Contents Wiper Blades Check the condition of the wiper blades at least every 6 months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace a front wiper blade: 1. Raise the wiper arm off the windshield. Raise the driver’s side first, then the passenger’s side. 154 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Table of Contents Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. REINFORCEMENT 4. Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade. Maintenance 3.
Table of Contents Table of Contents Wiper Blades BLADE REINFORCEMENT To replace a rear wiper blade: 1. Raise the wiper arm off the rear window. 2. Pull one end of the blade out from the holder. 4. Examine the new wiper blade. If it has no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade and install them in the slots along the edge of the new blade. 3. Slide the blade out of the holder. 5. Slide the new blade into the holder.
Table of Contents Table of Contents Tires Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced. Follow all instructions in this owner’s manual regarding tire inflation and maintenance.
Table of Contents Table of Contents Tires If you check air pressures when the tires are hot (driven for several miles), you will see readings 4 to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated. While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.
Table of Contents Table of Contents Tires Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. INDICATOR LOCATION MARKS You should look for: Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Your tires have wear indicators molded into the tread.
Table of Contents Table of Contents Tires Tire Rotation Front Front (Front Non-directional (Front Directional Tires and Wheels) Tires and Wheels) To help increase tire life and distribute wear more evenly, rotate the tires every 10,000 miles (16,000 km). Move the tires to the positions shown in the chart each time they are rotated. If you purchase directional tires, rotate only front-toback.
Table of Contents Table of Contents Tires Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an allweather tread design suitable for most winter driving conditions. For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions. Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels.
Table of Contents Table of Contents Checking the Battery TEST INDICATOR WINDOW Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors. 162 Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel.
Table of Contents Table of Contents Vehicle Storage If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors. Block the rear wheels. If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.
Table of Contents 164
Table of Contents Taking Care of the Unexpected This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed. Compact Spare Tire....................... 166 Changing a Flat Tire .....................
Table of Contents Table of Contents Compact Spare Tire Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm ) Follow these precautions: Never exceed 50 mph (80 km/h). This tire gives a harsher ride and less traction on some road surfaces.
Table of Contents Table of Contents Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. Use the jack that came with your vehicle. If you try to raise another vehicle with this jack or use another jack to raise your vehicle, the vehicle or jack can be damaged.
Table of Contents Table of Contents Changing a Flat Tire JACKING POINT 7. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch. 168 WHEEL WRENCH BRAKE HUB EXTENSION 8. Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground. 9. Remove the wheel nuts, then remove the flat tire.
Table of Contents Table of Contents Changing a Flat Tire CENTER CAP 12. Lower the vehicle to the ground and remove the jack. 14. Remove the center cap before storing the flat tire in the spare tire well. Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m) 169 Taking Care of the Unexpected 13. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Table of Contents Table of Contents Changing a Flat Tire WING BOLT 18. Store the jack and tool kit back in the center of the spare tire. Loose items can fly around the interior in a crash and could seriously injure the occupants. SPACER CONE 15.Place the flat tire face down in the spare tire well. 16. Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt. 17. Secure the flat tire by screwing the wing bolt back into its hole.
Table of Contents Table of Contents If the Engine Won’t Start Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the key to START (III): You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Table of Contents Table of Contents If the Engine Won’t Start The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to START (III), but the engine does not run. Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the dash panel to blink rapidly (see page 65 ). Are you using the proper starting procedure? Refer to Starting the Engine on page 123 .
Table of Contents Table of Contents Jump Starting Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery. To jump start your vehicle: 1. Open the hood, and check the physical condition of the battery. In very cold weather, check the condition of the electrolyte.
Table of Contents Table of Contents Jump Starting, If the Engine Overheats 6. Start the vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact. 7. Once the vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from the vehicle, and then from the booster battery. The numbers in the illustrations show you the order to connect the jumper cables. 5.
Table of Contents Table of Contents If the Engine Overheats Steam and spray from an overheated engine can seriously scald you. Do not open the hood if steam is coming out. 1. Safely pull to the side of the road. Put the transmission in Neutral, and set the parking brake. Turn off the all accessories, and turn on the hazard warning indicators. 2. If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood. 5.
Table of Contents Table of Contents If the Engine Overheats 7. If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the temperature gauge or lower before checking the radiator. Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator cap. 176 8.
Table of Contents Table of Contents Low Oil Pressure Indicator, Charging System Indicator 1. Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators. Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped. 3. If necessary, add oil to bring the level back to the full mark on the dipstick (see page 138 ). 2. Let the vehicle sit for a minute.
Table of Contents Table of Contents Malfunction Indicator Lamp If the indicator comes on while driving, it means one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage. If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap.
Table of Contents Table of Contents Brake System Indicator The brake system indicator normally comes on when you turn the ignition switch to ON (II), and as a Canada reminder to check the parking brake. It will stay on if you do not fully release the parking brake. U.S. If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads. Slow down by shifting to a lower gear, and pull to the side of the road when it is safe.
Table of Contents Table of Contents Closing the Moonroof If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET Front 1. Check the fuse for the moonroof motor (see page 185 ). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the cargo area.
Table of Contents Table of Contents Fuses INTERIOR Checking and Replacing Fuses If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages 184 and 185 , or the diagram on the fuse box lid, which fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works.
Table of Contents Table of Contents Fuses FUSE BLOWN BLOWN 1. Turn the ignition switch to LOCK (0). Make sure the headlights and all other accessories are off. 2. Remove the cover from the fuse box. 3. Check each of the large fuses in the under-hood fuse box by looking through the top at the wire inside. Remove the screws with a phillips-head screwdriver. 182 FUSE PULLER 4.
Table of Contents Table of Contents Fuses If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio). If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong.
Table of Contents Table of Contents Fuse Locations UNDER-HOOD FUSE BOX No. Amps. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20A 15A 7.
Table of Contents Table of Contents Fuse Locations INTERIOR FUSE BOX No. Amps. 1 2 3 4 5 6 7 8 9 10 15A 20A 10A 10A 7.5A 20A 7.5A 10A 7.5A 7.5A 7.5A 10A 10A 23 24 25 20A 20A 15A 15A 7.
Table of Contents Table of Contents Emergency Towing If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous. If, due to damage, your vehicle must be towed with the front wheels on the ground, do the following: Release the parking brake. Shift the transmission to Neutral. There are only two ways to tow your vehicle. Flat-bed Equipment The operator loads your vehicle on the back of a truck.
Table of Contents Table of Contents Emergency Towing If you decide to tow your vehicle with all four wheels on the ground, make sure you use a properlydesigned and attached tow bar. Prepare the vehicle for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery.
Table of Contents 188
Table of Contents Technical Information The diagrams in this section give you the dimensions and capacities of your vehicle, and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Identification Numbers ................. 190 Specifications ................................. 192 DOT Tire Quality Grading (U.S. Vehicles) ....................... 194 Treadwear .................................. 194 Traction.........
Table of Contents Table of Contents Identification Numbers Your vehicle has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
Table of Contents Table of Contents Identification Numbers The Engine Number is stamped into the engine block. The Transmission Number is on a label on top of the transmission.
Table of Contents Table of Contents Specifications Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating Engine Type Bore x Stroke Displacement Compression ratio Spark plugs 192 162.8 in (4,135 mm) 66.7 in (1,695 mm) 56.3 in (1,430 mm) 101.2 in (2,570 mm) 57.9 in (1,470 mm) 58.0 in (1,472 mm) See the certification label attached to the driver’s doorjamb. Water cooled 4-stroke DOHC i-VTEC 4-cylinder gasoline engine 3.39 x 3.39 in (86.0 x 86.0 mm) 121.
Table of Contents Table of Contents Specifications Air Conditioning Refrigerant type Charge quantity Lubricant type HFC-134a (R-134a) 16.9 18.6 oz (500 550 g) SP-10 Fuses Interior See page 185 or the fuse label attached to the inside of the fuse box door under the dashboard. See page 184 or the fuse box cover. Under-hood Lights Headlights HI LO Battery Capacity 60 W (HB3) 51 W (HB4) 21 W 3 CP (5 W) 5W 2 CP (3.8 W) 21 W 21/5 W 2 CP (3.
Table of Contents Table of Contents DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Table of Contents Table of Contents DOT Tire Quality Grading (U.S. Vehicles), Tire Labeling separately or in combination, can cause heat buildup and possible tire failure. Tire Labeling The tires that came on your vehicle have a number of markings. Those you should be aware of are described below. R 16 89 V Tire construction code (R indicates radial). Rim diameter in inches. Load index (a numerical code associated with the maximum load the tire can carry).
Table of Contents Table of Contents Emissions Controls The burning of gasoline in your vehicle’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.
Table of Contents Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, ignition timing control, and three way catalytic converter. These three systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Table of Contents Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Table of Contents Table of Contents State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the onboard diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Table of Contents Table of Contents State Emissions Testing Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway in 5th. Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
Table of Contents Warranty and Customer Relations 201 Warranty and Customer Relations Customer Service Information ................................. 202 Warranty Coverages ..................... 203 Reporting Safety Defects (U.S. Vehicles) ........................... 204 Authorized Manuals ......................
Table of Contents Table of Contents Customer Service Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The service manager or general manager can help. Almost all problems are solved in this way.
Table of Contents Table of Contents Warranty Coverages U.S. Owners Your new vehicle is covered by these warranties: Seat Belt Limited Warranty a seat belt that fails to function properly is covered for the useful life of the vehicle. Replacement Battery Limited Warranty provides prorated coverage for a replacement battery purchased from your dealer. Emissions Control Systems Defects Warranty and Emissions Performance Warranty these two warranties cover your vehicle’s emissions control systems.
Table of Contents Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc. 204 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Table of Contents Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) Valid only for sales within the United States. Canadian owners should contact their authorized Honda dealer. The publications shown below can be purchased from Helm Incorporated. You can order in any of three ways: Detach and mail the order form on the right half of this page Call Helm Inc. at 1-800-782-4356 (credit card orders only) Go online at www. helminc.
Table of Contents Table of Contents Authorized Manuals NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention the shipment should be sent. For purchases outside U.S.A. please write to the address shown below for a quotation. Attention Customer Name Street Address Apartment Number No P.O.
Table of Contents Index A Jump Starting ............................. 173 Maintenance ............................... 162 Specifications ............................. 193 Before Driving ............................... 109 Belts, Seat ..................................... 8, 18 Beverage Holders ............................ 83 Booster Seats ................................... 44 Brakes Break-in, New Linings .............. 110 Fluid ............................................ 144 Light, Burned-out .........
Table of Contents Index Bulb Replacement Back-up Lights ........................... 149 Stop Light ................................... 149 Front Parking Lights ................. 148 Front Side Marker Lights......... 147 Headlights .................................. 145 High-mount Brake Light .......... 150 License Plate Lights .................. 152 Side Marker Lights ................... 147 Side Turn Signal Lights ............ 151 Specifications ............................. 193 Turn Signal Lights .......
Table of Contents Index D E Economy, Fuel ............................... 114 Electric Power Steering (EPS)....... 55 Emergencies on the Road............. 165 Battery, Jump Starting .............. 173 Brake System Indicator ............ 179 Changing a Flat Tire ................. 167 Charging System Indicator ...... 177 Checking the Fuses................... 181 Low Oil Pressure Indicator ...... 177 Malfunction Indicator Lamp .... 178 Overheated Engine ................... 174 Emergency Brake ...............
Table of Contents Index Flashers, Hazard Warning.............. 62 Flat Tire, Changing a .................... 167 Fluids Brake ........................................... 144 Clutch .......................................... 144 Manual Transmission ............... 143 Windshield Washer ................... 142 FM Stereo Radio Reception ...................................... 93 Folding Rear Seat ............................ 73 Four-way Flashers ...........................
Table of Contents Index Instruments and Controls ............... 49 Instrument Panel ............................. 51 Instrument Panel Brightness ......... 62 Interior Convenience Items ............ 83 Interior Lights .................................. 81 Introduction ......................................... i J Jacking up the Vehicle .................. 168 Jack, Tire ........................................ 167 Jump Starting ................................. 173 K Keys .................................
Table of Contents Index M Maintenance ................................... 129 Owner Maintenance Checks.... 132 Record ................................. 135, 136 Safety........................................... 130 Schedule ..................................... 131 Malfunction Indicator Lamp .. 52, 178 Manual Transmission.................... 124 Manual Transmission Fluid ......... 143 Meters, Gauges ................................ 57 Mirrors, Adjusting ...........................
Table of Contents Index S Safety Belts................................. 10, 20 Safety Defects, Reporting .......... 204 Safety Features .................................. 9 Airbags .......................................... 11 Door Locks ................................... 12 Head Restraints ........................... 15 Seat Belts ...................................... 10 Seats and Seat-Backs................... 12 Safety Labels, Location of .............. 48 Safety Messages ..............................
Table of Contents Index SRS, Additional Information........... 23 Additional Safety Precautions .... 28 Airbag Components..................... 23 Airbag Service .............................. 28 How the Side Airbag Off Indicator Works ................ 27 How the SRS Indicator Works ........................................ 27 How Your Front Airbags Work.......................................... 24 How Your Side Airbags Work.... 26 SRS Indicator..............................
Table of Contents Index U Unexpected, Taking Care of the ........................................... 165 Uniform Tire Quality Grading ..... 194 Unleaded Gasoline......................... 110 Used Oil, How to Dispose of ........ 140 V Vehicle Capacity Load .................. 118 Vehicle Dimensions....................... 192 Vehicle Identification Number..... 190 Vehicle Storage .............................. 163 Ventilation......................................... 88 VIN ....................................
Table of Contents Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 86 or higher. Fuel Tank Capacity: 13.2 US gal (50 ) Recommended Engine Oil: API Certified ‘‘For Gasoline Engines’’ Oil, SAE 5W-20 viscosity (see page 138 ). Oil change capacity (including filter): 4.4 US qt (4.2 ) Manual Transmission Fluid: Honda Manual Transmission Fluid preferred, or an SAE 10W-30 or 10W-40 motor oil as a temporary replacement (see page 143 ). Oil change capacity (including differential): 1.