2005 Accord 4dr Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ......................................................................................................................................... i A Few Words About Safety.............................................................................
Main Menu Owner’s Identification This Owner’s Manual should be considered a permanent part of the vehicle and should remain with the vehicle when it is sold. OWNER This Owner’s Manual covers all models of the Accord Sedan. You may find descriptions of equipment and features that are not on your particular model. ADDRESS STREET CITY STATE/PROVINCE ZIP CODE/ POSTAL CODE V. I. N.
Main Menu Introduction Congratulations! Your selection of a 2005 Honda Accord was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your vehicle so you can refer to it at any time. As you read this manual, you will find information that is preceded by a symbol.
Main Menu A Few Words About Safety Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining your vehicle.
Main Menu Your Vehicle at a Glance AIRBAGS (P.11, 23) INDICATORS (P.58) GAUGES (P.64) MIRROR CONTROLS (P.94) AUDIO SYSTEM (P.118) HEATING/COOLING CONTROLS (P.106) POWER DOOR LOCK SWITCH (P.79) AUTOMATIC TRANSMISSION (P.178) MANUAL TRANSMISSION (P.176) POWER WINDOW SWITCHES (P.95) TRUNK RELEASE LEVER (P.85) FUEL FILL DOOR RELEASE LEVER (P.162) 4 HOOD RELEASE HANDLE (P.163) ACCESSORY POWER SOCKETS (P.
Main Menu Your Vehicle at a Glance WINDSHIELD WIPERS/WASHERS (P.69) PASSENGER AIRBAG OFF INDICATOR (P.31) Your Vehicle at a Glance INSTRUMENT PANEL BRIGHTNESS (P.72) HEADLIGHTS/ TURN SIGNALS (P.70) HAZARD WARNING BUTTON (P.72) REMOTE AUDIO CONTROLS (P.147) CRUISE CONTROLS (P.151) VOICE CONTROL SWITCHES＊ REAR WINDOW DEFOGGER (P.73, 109, 112) MOONROOF SWITCH (P.98) TRACTION CONTROL SYSTEM (P.187) STEERING WHEEL ADJUSTMENT (P.74) HORN ＊ : Only on vehicles equipped with Navigation System.
Main Menu 6
Main Menu Driver and Passenger Safety Important Safety Precautions .......... 8 Your Vehicle’s Safety Features........ 9 Seat Belts ...................................... 10 Airbags .......................................... 11 Protecting Adults and Teens.......... 13 1. Close and Lock the Doors ...... 13 2. Adjust the Front Seats ............ 13 3. Adjust the Seat-Backs ............. 14 4. Adjust the Head Restraints .... 15 5. Fasten and Position the Seat Belts ......................................
Main Menu Table of Contents Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags are designed to supplement seat belts, not replace them.
Main Menu Table of Contents Your Vehicle’s Safety Features (3) (10) (8) (9) (1) (4) (8) Some features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment; front and rear crush zones; a collapsible steering column; and tensioners that tighten the front seat belts in a crash.
Main Menu Table of Contents Your Vehicle’s Safety Features Seat Belts Your vehicle is equipped with seat belts in all seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your seat belts. Not wearing a seat belt properly increases the chance of serious injury or death in a crash, even though your vehicle has airbags. Be sure you and your passengers always wear seat belts and wear them properly.
Main Menu Table of Contents Your Vehicle’s Safety Features Airbags Driver and Passenger Safety Your vehicle has a Supplemental Restraint System (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision (see page 25 for more information on how your front airbags work).
Main Menu Table of Contents Your Vehicle’s Safety Features The most important things you need to know about your airbags are: Airbags do not replace seat belts. They are designed to supplement the seat belts. Airbags offer no protection in rear impacts, or minor frontal or side collisions. Airbags can pose hazards. To do their job, airbags must inflate with tremendous force.
Main Menu Table of Contents Protecting Adults and Teens See pages 34 − 51 for important guidelines on how to properly protect infants, small children and larger children who ride in your vehicle. 1.Close and Lock the Doors After everyone has entered the vehicle, be sure the doors are closed and locked. Locking the doors reduces the chance of someone being thrown out of the vehicle during a crash, and it helps prevent passengers from accidentally opening a door and falling out. 2.
Main Menu Table of Contents Protecting Adults and Teens If you sit too close to the steering wheel or dashboard, you can be seriously injured by an inflating front airbag, or by striking the steering wheel or dashboard. The National Highway Traffic Safety Administration and Transport Canada recommend that drivers allow at least 10 inches (25 cm) between the center of the steering wheel and the chest. In addition to adjusting the seat, you can adjust the steering wheel in and out (see page 74 ).
Main Menu Table of Contents Protecting Adults and Teens 4.Adjust the Head Restraints Adjust the seat-back to an upright position, and sit well back in the seat. Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant’s chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury.
Main Menu Table of Contents Protecting Adults and Teens This spreads the forces of a crash over the strongest bones in your upper body. 5.Fasten and Position the Seat Belts Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash. Improperly positioning the seat belts can cause serious injury or death in a crash.
Main Menu Table of Contents Protecting Adults and Teens RELEASE BUTTONS Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause If a seat belt doesn’t seem to work properly, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt. Using a seat The front seats have adjustable seat belt anchors.
Main Menu Table of Contents Protecting Adults and Teens In addition, an occupant who is out of position in the front seat can be seriously or fatally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag. Advice for Pregnant Women This will reduce the risk of injuries to both you and your unborn child that can be caused by a crash or an inflating front airbag. Sitting improperly or out of position can result in serious injury or death in a crash.
Main Menu Table of Contents Protecting Adults and Teens Additional Safety Precautions Two people should never use the same seat belt. If they do, they Keep your hands and arms away from the airbag covers. If your hands or arms are close to an airbag cover, they could be injured if the airbag inflates. Do not put any accessories on seat belts. Devices intended to improve Do not attach or place objects on the front airbag covers.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The front seat belts are also equipped with automatic seat belt tensioners. The seat belt system includes an indicator on the instrument panel and a beeper to remind you to fasten your seat belt. If you turn the ignition switch to ON (II) before fastening your belt, the beeper will sound and the indicator will flash.
Main Menu Table of Contents Additional Information About Your Seat Belts Automatic Seat Belt Tensioners Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. The tensioners can also be activated during a collision in which the front airbags do not deploy. In this case, the airbags would not be needed, but the additional restraint could be helpful. Pull each belt out fully and look for frays, cuts, burns, and wear.
Main Menu Table of Contents Additional Information About Your Seat Belts If a seat belt is worn during a crash, it must be replaced by the dealer. A belt that has been worn during a crash may not provide the same level of protection in a subsequent crash. The dealer should also inspect the anchors for damage and replace them if needed. If the automatic seat belt tensioners activate during a crash, they must be replaced. For information on how to clean your seat belts, see page 233 .
Main Menu Table of Contents Additional Information About Your Airbags Your airbag system includes: Airbag System Components (8) (9) (2) (11) (8) (5) Two SRS (Supplemental Restraint System) front airbags. The driver’s airbag is stored in the center of the steering wheel; the front passenger’s airbag is stored in the dashboard. Both are marked ‘‘SRS AIRBAG’’ (see page 25 ). Two side airbags, one for the driver and one for a front passenger. The airbags are stored in the outer edges of the seatbacks.
Main Menu Table of Contents Additional Information About Your Airbags Automatic front seat belt tensioners (see page 21 ). Sensors that can detect a moderate to severe front impact or side impact. Sensors that can detect whether a child is in the passenger’s side airbag path and automatically turn the airbag off (see page 27 ). A driver’s seat position sensor that monitors the distance of the seat from the front airbag.
Main Menu Table of Contents Additional Information About Your Airbags How Your Front Airbags Work Driver and Passenger Safety During a frontal crash, your seat belt restrains your lower body and torso, and the front airbag helps protect your head and chest. Although both airbags normally inflate within a split second of each other, it is possible for only one airbag to deploy. If you ever have a moderate to severe frontal collision, sensors will detect the vehicle’s rapid deceleration.
Main Menu Table of Contents Additional Information About Your Airbags After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the vehicle as soon as it is safe to do so. Dual-Stage Airbags Dual-Threshold Airbags Your front airbags are dual-stage airbags.
Main Menu Table of Contents Additional Information About Your Airbags Advanced Airbags For both advanced airbags to work properly: Occupants must sit upright and wear their seat belts properly. Do not spill any liquids on or under the seats, cover the sensors, or put any cargo or metal objects under the front seats. Back-seat passengers should not put their feet under the front seats. Failure to follow these instructions could damage the sensors or prevent them from working properly.
Main Menu Table of Contents Additional Information About Your Airbags When the airbag is turned off, an indicator in the center of the dashboard will come on indicating ‘‘Passenger Airbag Off’’ (see page 31 ). If there is no passenger in the front seat, the airbag will be off. However, the Passenger Airbag Off indicator will not come on.
Main Menu Table of Contents Additional Information About Your Airbags To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats. Side Airbag Cutoff System To reduce the risk of injury from an inflating side airbag, your vehicle has an automatic cutoff system for the passenger’s side airbag.
Main Menu Table of Contents Additional Information About Your Airbags How Your Side Curtain Airbags Work If the impact is on the passenger’s side, the passenger’s side curtain airbag will inflate even if there are no occupants on that side of the vehicle. To get the best protection from the side curtain airbags, occupants should wear their seat belts and sit upright and well back in their seats.
Main Menu Table of Contents Additional Information About Your Airbags Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly. Have your vehicle checked by a dealer as soon as possible if the SRS indicator alerts you to a possible problem. How the Side Airbag Off Indicator Works U.S. Canada This indicator alerts you that the passenger’s side airbag has been automatically shut off.
Main Menu Table of Contents Additional Information About Your Airbags If no one is riding in the front seat, the airbag will be automatically shut off. However, the indicator will not come on. However, if the indicator comes on with no passenger in the front, or with an adult in the seat, there may be a problem with the advanced airbag system. Have the vehicle checked by the dealer as soon as possible.
Main Menu Table of Contents Additional Information About Your Airbags Additional Safety Precautions Do not attempt to deactivate your airbags. Together, airbags and or covering front seat-back covers can prevent your side airbags from inflating during a side impact. Driver and Passenger Safety seat belts provide the best protection. Do not cover or replace front seatback covers without consulting your dealer. Improperly replacing Do not tamper with airbag components or wiring for any reason.
Main Menu Table of Contents Protecting Children − General Guidelines All Children Must Be Restrained Each year, many children are injured or killed in vehicle crashes because they are either unrestrained or not properly restrained. In fact, vehicle accidents are the number one cause of the death of children ages 12 and under. Children depend on adults to protect them. However, despite their best intentions, many adults do not know how to properly protect child passengers.
Main Menu Table of Contents Protecting Children − General Guidelines Children who ride in back are less likely to be injured by striking interior vehicle parts during a collision or hard braking. Also, children cannot be injured by an inflating front airbag when they ride in the back. The Passenger’s Front Airbag Poses Serious Risks Front airbags have been designed to help protect adults in a moderate to severe frontal collision.
Main Menu Table of Contents Protecting Children − General Guidelines To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the dashboard (U.S. models) and on the front visors. Please read and follow the instructions on these labels. U.S.
Main Menu Table of Contents Protecting Children − General Guidelines Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page 48 ). Move the vehicle seat as far to the rear as possible (see page 13 ). If a Child Requires Close Attention Many parents say they prefer to put an infant or small child in the front passenger seat so they can watch the child, or because the child requires attention.
Main Menu Table of Contents Protecting Children − General Guidelines Additional Safety Precautions Never hold an infant or child on your lap. If you are not wearing a seat belt in crash, you could be thrown forward and crush the child against the dashboard or a seat-back. If you are wearing a seat belt, the child can be torn from your arms and be seriously hurt or killed. Never put a seat belt over yourself and a child.
Main Menu Table of Contents Protecting Infants and Small Children Protecting Infants Do not put a rear-facing child seat in a forward-facing position. If placed facing forward, an infant could be very seriously injured during a frontal collision. Child Seat Type An infant must be properly restrained in a rear-facing, reclining child seat until the child reaches the seat maker’s weight or height limit for the seat and the child is at least one year old.
Main Menu Table of Contents Protecting Infants and Small Children In any situation, we strongly recommend that you install the child seat directly behind the front passenger’s seat, more the seat as far forward as needed, and leave it unoccupied. Or, you may wish to get a smaller rear-facing child seat. Protecting Small Children Even with advanced front airbags, which can automatically turn the passenger’s front airbag off (see page 31 ), a back seat is the safest place for a small child.
Main Menu Table of Contents Protecting Infants and Small Children, Selecting a Child Seat Selecting a Child Seat When buying a child seat, you need to choose either a conventional child seat, or one designed for use with the Lower Anchors and Tethers for Children (LATCH) system. Placing a forward-facing child seat in the front seat can result in serious injury or death if the front airbag inflates.
Main Menu Table of Contents Selecting a Child Seat, Installing a Child Seat 3. The child seat should fit the vehicle seating position (or positions) where it will be used. Before purchasing a conventional child seat, or using a previously purchased one, we recommend that you test the seat in the specific vehicle seating position, or positions, where the seat will be used.
Main Menu Table of Contents Installing a Child Seat The lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH. The location of each lower anchor is indicated by a small button above the anchor point. LOWER ANCHOR MARKS To install a LATCH-compatible child seat: 1. Move the seat belt buckle or tongue away from the lower anchors. 2.
Main Menu Table of Contents Installing a Child Seat TETHER STRAP HOOK Flexible type Other LATCH-compatible seats have a flexible-type connection as shown above. 4. Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit. ANCHOR 5. Lift the head restraint (see page 90 ), then route the tether strap through the legs of the head restraint, over the seat-back, making sure the strap is not twisted. 6.
Main Menu Table of Contents Installing a Child Seat In addition, the lap/shoulder belts in all seating positions except the driver’s have a locking mechanism that must be activated to secure a child seat. 1. With the child seat in the desired seating position, route the belt through the child seat according to the seat maker’s instructions, then insert the latch plate into the buckle. 2.
Main Menu Table of Contents Installing a Child Seat To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Installing a Child Seat Installing a Child Seat with a Tether Using an Outer Anchor TETHER STRAP HOOK A child seat with a tether can be installed in any seating position in the back seat, using one of the anchorage points shown above. Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available. ANCHOR 1.
Main Menu Table of Contents Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in a back seat on a booster seat and wear a lap/shoulder belt. Allowing a child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.
Main Menu Table of Contents Protecting Larger Children 3. Does the shoulder belt cross between the child’s neck and arm? Using a Booster Seat 5. Will the child be able to stay seated like this for the whole trip? If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly. If you answer no to any question, the child needs to ride on a booster seat.
Main Menu Table of Contents Protecting Larger Children When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in a back seat. If the passenger’s front airbag inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position. A side airbag also poses risks.
Main Menu Table of Contents Protecting Larger Children Additional Safety Precautions Do not let a child wear a seat belt across the neck. This could result Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could improve a child’s comfort or reposition the shoulder part of a seat belt can make the belt less effective and increase the chance of serious injury in a crash. Driver and Passenger Safety in serious neck injuries during a crash.
Main Menu Table of Contents Carbon Monoxide Hazard Your vehicle’s exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the vehicle in normal driving if you maintain your vehicle properly. Have the exhaust system inspected for leaks whenever: Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide. The vehicle is raised for an oil change.
Main Menu Table of Contents Safety Labels SUN VISOR DOORJAMBS U.S. models U.S. models Canadian models HOOD DASHBOARD Canadian models U.S. models U.S. models only U.S. models Canadian models Driver and Passenger Safety These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. If a label comes off or becomes hard to read, contact your dealer for a replacement.
Main Menu 54
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach. Seat .................................................... 88 Power Seat Adjustment .............. 88 Driver’s Lumbar Support ............ 89 Front Seat Adjustments .............. 89 Driver’s Seat Manual Height Adjustment ............................... 90 Driver’s Seat Power Height Adjustment ............
Main Menu Table of Contents Control Locations INDICATORS(P.58) GAUGES (P.64) MOONROOF SWITCH (P.98) MIRROR CONTROLS (P.94) POWER DOOR LOCK SWITCHES (P.79) POWER WINDOW SWITCHES (P.95) HOOD RELEASE TRUNK RELEASE LEVER (P.85) HANDLE PARKING BRAKE LEVER FUEL FILL DOOR RELEASE LEVER (P.163) (P.99) (P.162) 56 CRUISE CONTROLS (P.151) HAZARD WARNING BUTTON (P.72) AUDIO SYSTEM (P.118, 119, 126, 127, 136 ,137) DIGITAL CLOCK (P.149) HEATING/COOLING CONTROLS (P.106) CLIMATE CONTROL SYSTEM (P.
Main Menu Table of Contents Instrument Panel LOW OIL PRESSURE INDICATOR (P.58) ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR (P.59) CRUISE CONTROL MAIN INDICATOR (P.63) HIGH BEAM INDICATOR (P.62) CRUISE CONTROL INDICATOR (P.63) TRACTION CONTROL SYSTEM INDICATOR (P.60) IMMOBILIZER SYSTEM INDICATOR (P.63) MAINTENANCE REQUIRED INDICATOR (P.70) DOOR AND TRUNK OPEN MONITOR (P.60) SIDE AIRBAG OFF INDICATOR (P.59) SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR(P.59) SECURITY SYSTEM INDICATOR (P.
Main Menu Table of Contents Instrument Panel Lights The instrument panel has many indicators to give you important information about your vehicle. Seat Belt Reminder Light This indicator comes on when you turn the ignition switch to ON (II). It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt. If you turn the ignition switch to ON (II) before fastening your seat belt, the beeper sounds and the indicator flashes.
Main Menu Table of Contents Instrument Panel Lights U.S. Canada Side Airbag Off Indicator This indicator comes on when you turn the ignition switch to ON (II). If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page 31 . Anti-lock Brake System (ABS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to ON (II), and when the ignition switch is turned to START (III).
Main Menu Table of Contents Instrument Panel Lights TCS Activation Indicator On LX-V6 and EX-V6 models This indicator has three functions: 1. It comes on as a reminder that you have turned off the Traction Control System. 2. It flashes when the TCS is regulating wheelspin. 3. If it comes on and stays on when the Traction Control System is on, it indicates that there is a problem with the TCS. This indicator also comes on for a few seconds when you turn the ignition switch to ON (II).
Main Menu Table of Contents Instrument Panel Lights When you turn on the Hazard Warning button, both turn signal indicators blink. All turn signals on the outside of the vehicle should flash. Lights On Indicator (U.S. models only) Low Fuel Indicator If equipped This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the or position. This indicator will also come on when the light switch is in AUTO and the lights turn on automatically.
Main Menu Table of Contents Instrument Panel Lights Security System Indicator SECURITY SYSTEM INDICATOR ‘‘Daytime Running Lights’’ Indicator Canadian models only This indicator comes on when you turn the ignition switch to ON (II) with the headlight switch off and the parking brake set. It should go off if you turn on the headlights or release the parking brake. If it comes on at any other time, it means there is a problem with the DRL. There may also be a problem with the high beam headlights.
Main Menu Table of Contents Instrument Panel Lights Cruise Control Main Indicator Cruise Control Indicator Only on models equipped with Cruise Control System This indicator comes on when you turn on the Cruise Control Master Button. (see page 151 .) This indicator comes on when you set the cruise control. See page 151 for information on operating the cruise control. This indicator also blinks several times when you turn the ignition switch from ON (II) to ACCESSORY (I) or LOCK (0).
Main Menu Table of Contents Gauges TACHOMETER SPEEDOMETER Outside Temperature Display FUEL GAUGE On EX-L and EX-V6 models MAINTENANCE REQUIRED INDICATOR TEMPERATURE GAUGE ODOMETER/OUTSIDE TRIP METER U.S. model is shown. TEMPERATURE INDICATOR Odometer/Outside Temperature Display The odometer and the outside temperature display use the same display. To switch the display between the odometer and the outside temperature, press the Select/Reset knob.
Main Menu Table of Contents Gauges Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. NOTE: The temperature must be stabilized before doing this procedure. There are two trip meters: Trip A and Trip B. Switch between these displays and the odometer/outside temperature display by pressing the Select/Reset knob repeatedly. Each trip meter works independently, so you can keep track of two different distances.
Main Menu Table of Contents Gauges Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition. Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.
Main Menu Table of Contents Gauges 6-cylinder models For the first 6,000 miles (9,600 km) after the Maintenance Required Indicator is reset, it will come on for two seconds when you turn the ignition switch to ON (II). Between 8,000 miles (12,800 km) and 10,000 miles (16,000 km), this indicator will light for two seconds when you first turn the ignition switch to ON (II), and then flash for ten seconds.
Main Menu Table of Contents Controls Near the Steering Wheel INSTRUMENT PANEL BRIGHTNESS (P.72) WINDSHIELD WIPERS/WASHERS (P.69) PASSENGER AIRBAG OFF INDICATOR (P.31) HEADLIGHTS/ TURN SIGNALS (P.70) HAZARD WARNING BUTTON (P.72) REMOTE AUDIO CONTROLS (P.147) CRUISE CONTROLS (P.151) VOICE CONTROL SWITCHES＊ REAR WINDOW DEFOGGER (P.73, 109, 112) MOONROOF SWITCH (P.98) TRACTION CONTROL SYSTEM (P.187) STEERING WHEEL ADJUSTMENT (P.74) HORN ＊ : Only on vehicles equipped with Navigation System.
Main Menu Table of Contents Wipers and Washers Windshield Wiper Push the right lever up or down to select a position. LO − The wipers run at low speed. HI − The wipers run at high speed. MIST − The wipers run at high speed until you release the lever. 1. MIST 2. OFF 3. INT − Intermittent 4. LO − Low 5. HI − High 6. Windshield Washers INT − The length of the wiper interval is varied automatically according to the vehicle’s speed. Vary the delay by turning the INT TIME ring.
Main Menu Table of Contents Turn Signal, Headlights Turn Signal and Headlights 1. Turn Signal 2. Off 3. Parking and interior lights 4. Headlight on 5. High beams 6. Flash high beams 70 Turn Signal − Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever in the proper direction and hold it. The lever will return to center when you release it or complete a turn.
Main Menu Table of Contents Headlights, Automatic Lighting Off Feature Automatic Lighting Off Feature On all models except U.S. DX This feature turns off the headlights, parking lights, taillights, and license plate light within 15 seconds of removing the key from the ignition switch and closing the driver’s door. This feature activates if you leave the headlight switch in the ‘‘ ’’ or ‘‘ ’’ position, remove the key, then open and close the driver’s door.
Main Menu Table of Contents Daytime Running Lights, Instrument Panel Brightness, Hazard Warning Daytime Running Lights (Canadian Models) With the headlight switch off, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake. The headlights revert to normal operation when you turn them on with the switch.
Main Menu Table of Contents Rear Window Defogger Make sure the rear window is clear and you have good visibility before starting to drive. Instruments and Controls The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side. Manual A/C type shown The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off.
Main Menu Table of Contents Steering Wheel Adjustment Make any steering wheel adjustment before you start driving. Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash. 1. Insert the key in the ignition switch, and unlock the steering column. 2. Push the lever under the steering column all the way down. Adjust the steering wheel only when the vehicle is stopped. 3.
Main Menu Table of Contents Steering Wheel Adjustment, Keys and Locks 4. Push the lever up to lock the steering wheel in that position. MASTER VALET KEY KEY NUMBER KEY (LIGHT GREY) (BLACK) TAG Only on DX models MASTER VALET KEY KEY NUMBER KEY WITH (LIGHT GREY) REMOTE TAG TRANSMITER Instruments and Controls 5. Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
Main Menu Table of Contents Keys and Locks The master key fits all the locks on your vehicle. The valet key works only in the ignition and the door locks. You can keep the trunk release handle, rear seat trunk access, and glove box locked when you leave your vehicle and the valet key at a parking facility. You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
Main Menu Table of Contents Immobilizer System The Immobilizer System protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine will not start. The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable.
Main Menu Table of Contents Ignition Switch LOCK (0) − You can insert or remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly. If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or to the right as you turn the key.
Main Menu Table of Contents Ignition Switch, Door Locks Door Locks On all models except U.S. DX MASTER DOOR LOCK SWITCH top bottom To lock any passenger’s door when getting out of the vehicle, push the lock tab down and close the door. If your vehicle has an automatic transmission, the shift lever must be in Park before you can remove the key from the ignition switch. Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.
Main Menu Table of Contents Door Locks On Canadian DX models, all doors can be locked from the outside by using the key in either front door. To unlock only the driver’s door from the outside, insert the key in the driver’s door lock, turn the key and release it. If you turn the key again, all doors will unlock. All four doors will unlock when you unlock the passenger’s door with the key. 80 On LX and EX models, all doors can be locked from the outside by using the key in the driver’s door.
Main Menu Table of Contents Childproof Door Locks, Remote Transmitter Childproof Door Locks Remote Transmitter LEVER PANIC BUTTON The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up and use the outside door handle.
Main Menu Table of Contents Remote Transmitter You cannot lock the doors with the remote transmitter if any door is not fully closed or the key is in the ignition switch. On all models except DX If you unlock the doors with the remote transmitter, but do not open any of the doors within 30 seconds, the doors automatically relock. On the EX model, the security system will also set. To open the trunk, push the Trunk Release button for about 1 second.
Main Menu Table of Contents Remote Transmitter Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible. BATTERY SCREW To replace the battery: 1. Remove the screw at the base of the transmitter with a small Phillips-head screwdriver. 2. Separate the transmitter by prying its middle seam with your fingernail. TAB 3.
Main Menu Table of Contents Remote Transmitter As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Main Menu Table of Contents Trunk MASTER KEY Pull You can open the trunk in any of three ways: Pull up on the trunk release lever located to the left of the driver’s seat. Use the master key to open the trunk lock. The valet key does not work in this lock. Press and hold the trunk release button on the remote transmitter. (all models except U.S. DX) MASTER KEY To close the trunk, press down on the trunk lid. See page 171 for cargo loading and weight limit information.
Main Menu Table of Contents Trunk Emergency Trunk Opener To open the trunk, push the release lever to the left. Parents should decide if their children should be shown how to use this feature. As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from the inside.
Main Menu Table of Contents Seat Heaters After the seat reaches a comfortable temperature, select LO by pushing the back of the switch. This will keep the seat warm. In LO, the heater runs continuously. It does not cycle with temperature changes. Use the HI setting only to heat the seats quickly, because it draws large amounts of current from the battery. If the engine is left idling for an extended period, do not use the seat heaters even on the LO setting.
Main Menu Table of Contents Seats The 4-cylinder EX model without leather interior has a power height adjustment for the driver’s seat. All other seat adjustments in this model are manual. Power Seat Adjustment On EX, EX-L, LX-V6 and EX-V6 models See pages 13 − 14 for important safety information and warnings about how to properly position seats and seat-backs. The controls for the adjustable driver’s power seat are on the outside edge of the seat bottom.
Main Menu Table of Contents Seats Driver’s Lumbar Support Front Seat Adjustments On EX, EX-L and EX-V6 models To adjust the seat forward and backward, pull up on the lever under the seat cushion’s front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position. To change the seat-back angle, pull up on the lever on the outside of the seat bottom.
Main Menu Table of Contents Seats Driver’s Seat Manual Height Adjustment Driver’s Seat Power Height Adjustment Head Restraints RELEASE BUTTON On DX and LX models On EX model The height of your driver’s seat is adjustable. To raise the seat bottom, repeatedly pull up the lever on the outside of the seat cushion. To lower the seat, push the lever down repeatedly. The height of your driver’s seat is power adjustable. Pull up on the switch to raise the seat. Push it down to lower the seat.
Main Menu Table of Contents Seats They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint. Folding Rear Seat MASTER KEY GUIDE The back of the rear seat folds down, giving you direct access to the trunk. The seat-back can be released from inside the vehicle or inside the trunk. When storing cargo, you can move the rear center shoulder belt out of the way by removing the belt from the guide.
Main Menu Table of Contents Seats Make sure all rear shoulder belts are positioned in front of the rear seatback whenever the seat-back is in its upright position. Pull To release the seat-back from inside the trunk, pull the release loop under the trunk panel. To lock the seat-back upright, push it firmly against the trunk panel. Make sure it is latched in place by pulling on the top of the seat.
Main Menu Table of Contents Seats Trunk Pass-through Cover KEY CYLINDER KNOB For security, this cover can be locked and unlocked only with the master key. To lock the cover, insert the key and turn it clockwise. Instruments and Controls Never drive with this cover open and the trunk lid open. See Carbon Monoxide Hazard on page 52 . LID On all models except DX The trunk pass-through cover can be opened from either side; it folds forward onto the center armrest.
Main Menu Table of Contents Mirrors Adjusting the Power Mirrors 4. When you finish, turn the adjustment knob to the center (off) position. This turns off the adjustment knob to keep your settings. TAB Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. ADJUSTMENT KNOB On all models except DX 1. Turn the ignition switch to ON (II). The outside mirrors are manually adjustable. The inside mirror has day and night positions.
Main Menu Table of Contents Mirrors, Power Windows Power Mirror Heaters Power Windows On all Canadian models except DX Closing a power window on someone’s hands or fingers can cause serious injury. HEATED MIRROR BUTTON DRIVER’S WINDOW SWITCH The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off.
Main Menu Table of Contents Power Windows To open or close the driver’s window partially, push down or pull back on the window switch lightly and hold it. The window will stop when you release the switch. The passenger windows cannot be raised or lowered if the MAIN switch is OFF. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.
Main Menu Table of Contents Power Windows Does not apply to U.S. DX Power Window Control Operations UNLOCK BUTTON Opening the Windows with the Remote Transmitter You can open all of the windows from the outside with the remote transmitter. 1. Press the UNLOCK button once to unlock the driver’s door. 2. Press the UNLOCK button a second time, and hold it. The passenger’s doors unlock, and all four windows start to open. To stop the windows, release the button. 3.
Main Menu Table of Contents Power Windows, Moonroof 3. Turn the key clockwise again, and hold it. All four windows start to open. To stop the windows, release the key. Moonroof 4. To open the windows further, turn and hold the key again. To close: 1. Insert the key in the driver’s door lock. 2. Turn the key counterclockwise, then release it. MOONROOF SWITCH On EX, EX-L and EX-V6 models 3. Turn the key counterclockwise again, and hold it. All four windows start to close.
Main Menu Table of Contents Moonroof, Parking Brake If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor. Parking Brake Driving the vehicle with the parking brake applied can damage the rear brakes and hubs. Instruments and Controls The moonroof has a key-off delay function. You can still open and close the moonroof for up to ten minutes after you turn off the ignition switch.
Main Menu Table of Contents Sun Visor, Vanity Mirror Sun Visor Vanity Mirror All models except the DX have lighted vanity mirrors. The lights come on when you pull up the cover. To use the sun visor, pull it down. You can also use the sun visor at the side window. Remove the support rod from the clip and swing the sun visor toward the side window. 100 To use a vanity mirror on the back of the sun visor, pull up the cover.
Main Menu Table of Contents Interior Lights Ceiling Light On LX models DOOR ACTIVATED DOOR ACTIVATED Push on the spotlight lenses to turn the light on and off. ON OFF COURTESY LIGHT The ceiling lights have a three or two-position switch; ON (for threeposition), Door Activated, and OFF. In the Door Activated (center or left) position, the lights come on when you: Open any door. Unlock the doors with the key or remote transmitter.
Main Menu Table of Contents Interior Convenience Items CONSOLE COMPARTMENT/ ACCESSORY POWER SOCKET FRONT DOOR POCKET/ BEVERAGE HOLDER CENTER POCKET/ COIN POCKET/ ACCESSORY POWER SOCKET BEVERAGE HOLDER REAR DOOR POCKET GLOVE BOX BEVERAGE HOLDERS TRUNK 102 SEAT-BACK POCKET＊ ＊: For some types
Main Menu Table of Contents Interior Convenience Items Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior. Accessory Power Sockets These sockets are intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps). None of the sockets will power an automotive type cigarette lighter element. When more than one socket is being used, the combined power rating of the accessories should be 120 watts or less (10 amps).
Main Menu Table of Contents Interior Convenience Items Sunglasses Holder Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. GLOVE BOX On all models except DX To open the sunglasses holder, push on the front edge. Make sure the holder is closed while you are driving. Open the glove box by pulling the handle to the left. Close it with a firm push.
Main Menu Features On all models except 4-cylinder DX and LX models Your Honda has an anti-theft audio system that requires a code number to enable it. The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. Caring the Tape and Player...... 140 Playing the XMTM Satellite Radio .......................................
Main Menu Table of Contents Vents, Heating, and A/C All models except EX-L and EX-V6 EX-L and EX-V6 Models without Navigation System TEMPERATURE DISPLAY FAN CONTROL DIAL RECIRCULATION BUTTON TEMPERATURE CONTROL DIAL (DRIVER’S SIDE) FAN SPEED INDICATOR TEMPERATURE CONTROL DIAL (PASSENGER’S SIDE) TEMPERATURE CONTROL DIAL MODE BUTTON AIR CONDITIONING BUTTON MAX A/C BUTTON REAR WINDOW DEFOGGER BUTTON WINDSHIELD DEFROST BUTTON MODE BUTTONS FAN CONTROL BUTTONS AIR CONDITIONING BUTTON AUTO BUTTON OF
Main Menu Table of Contents Vents, Heating, and A/C EX-L and EX-V6 Models with Navigation System (U.S.
Main Menu Table of Contents Vents, Heating, and A/C Heating and Cooling Air conditioning is optional for U.S. DX model. Your Honda dealer can install a Honda air conditioning system that is designed to fit in your vehicle. On EX-L and EX-V6 models with the navigation system, you can manually select the fan speed by pressing the A/C button next to the display and then, pressing the fan control icons. For vehicles with the navigation system, press the DUAL button. The indicator will come on.
Main Menu Table of Contents Vents, Heating, and A/C Air Conditioning (A/C) Button On all models except EX-L and EX-V6, this button turns the air conditioning on and off. The indicator in the button is on when the A/C is on. On vehicles with the navigation system, press the A/C button to view the display. Touching ‘‘ON’’ or ‘‘OFF’’ in the display turns the air conditioning on and off. You will see A/C ON or A/C OFF in the display.
Main Menu Table of Contents Vents, Heating, and A/C Mode Control Use the mode control buttons or icons to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes. When you select or , the system automatically switches to Fresh Air mode and turns on the A/C. In these modes, the A/C stays on with the indicator off. Air flows from the center and corner vents in the dashboard. When you select , the system automatically switches to Fresh Air mode.
Main Menu Table of Contents Vents, Heating, and A/C Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. . 1. Select When you select , the system automatically switches to the Fresh Air mode. 2. Set the fan to the desired speed. 3. Adjust the warmth of the air with the temperature control dial. EX-L and EX-V6 with Navigation System 1.
Main Menu Table of Contents Vents, Heating, and A/C Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Turn the fan on. 2. Turn on the air conditioning. and Fresh Air mode. 3. Select 4. Adjust the temperature control dial or buttons to your preference. This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).
Main Menu Table of Contents Vents, Heating, and A/C Press the AUTO button. On EX-L and EX-V6 models Without Navigation System: Set the The automatic climate control system adjusts the fan speed and airflow levels to maintain the interior temperature you select. desired temperature by turning the Temperature Control dial. You will see AUTO in the system’s display. With Navigation System: Set the desired temperature by pressing the ▲ to raise the temperature or ▼ to lower the temperature.
Main Menu Table of Contents Vents, Heating, and A/C Manual Operation You can manually select various functions of the automatic climate control system when it is in AUTO. All other features remain automatically controlled. EX-L and EX-V6 without Navigation System Manual selections will cause the word AUTO in the display to go out. To Turn Everything Off Press the OFF button. However, a lack of airflow can cause the windows to fog up.
Main Menu Table of Contents Dual Temperature Control On EX-L and EX-V6 models Without Navigation System Without Navigation System Your vehicle has two temperature control dials, one for the driver, and one for the passenger. With Navigation System The driver’s side and the passenger’s side can be controlled independently by adjusting these dials or buttons when the green indicator in the DUAL button is lit.
Main Menu Table of Contents Dual Temperature Control To set the driver’s side temperature to a different value than the passenger’s, press the DUAL button, then turn the driver’s control dial or press the ▲ or ▼ buttons on the driver’s side. To set the passenger’s side to a different value than the driver’s, turn the passenger’s control dial or press the ▲ or ▼ buttons on the passenger’s side. You can adjust the passenger’s side without pressing the DUAL button first.
Main Menu Table of Contents Climate Control Sensors Sunlight Sensor/Temperature Sensor SUNLIGHT SENSOR TEMPERATURE SENSOR Features The climate control system has two sensors. A sunlight sensor is in the top of the dashboard, and a temperature sensor is next to the steering column. Do not cover the sensors or spill any liquid on them.
Main Menu Table of Contents Playing the Radio DX and LX Models EX and LX-V6 Models without Navigation System STEREO INDICATOR AM/FM BUTTON STEREO INDICATOR SCAN BUTTON AM/FM BUTTON A.SEL BUTTON A.
Main Menu Table of Contents Playing the Radio EX-L, EX-V6 Models without Navigation System EX-L, EX-V6 Models with Navigation System (U.S. Vehicles Only) STEREO INDICATOR STEREO INDICATOR PRESET BARS A.
Main Menu Table of Contents Playing the Radio To Play the Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the PWR/VOL knob or the AM/FM button. Adjust the volume by turning the PWR/VOL knob. For Vehicles with Navigation System Pushing the AUDIO DISPLAY button will also turn on the system. The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button.
Main Menu Table of Contents Playing the Radio Preset − Each preset bar or icon can store one frequency on AM, and two frequencies on FM. For Vehicles with Navigation System The preset frequencies will be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed. 4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve stations on FM. Features 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset bar or icon. 3.
Main Menu Table of Contents Playing the Radio AUTO SELECT − If you are traveling far from home and can no longer receive your preset stations, you can use the Auto Select feature to find stations in the local area. Press the A. SEL button or touch the Auto Select icon. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It stores the frequencies of six AM, and twelve FM stations in the preset bars (1 − 6) or icons.
Main Menu Table of Contents Playing the Radio Balance/Fader − These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength. Treble/Bass − Use the TRE/BAS modes to adjust the tone to your liking. On Vehicles with Navigation System If you want to adjust the sound while the radio/CD is playing, push the AUDIO DISPLAY button, then touch the SOUND icon in the display.
Main Menu Table of Contents Playing the Radio Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 megahertz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
Main Menu Table of Contents Playing the Radio As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Features Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter.
Main Menu Table of Contents Playing a CD DX and LX Models SCAN/RPT BUTTON CD BUTTON CD SLOT EJECT BUTTON SEEK/SKIP BAR PRESET BAR RPT BUTTON RDM BUTTON EJECT BUTTON CD SLOT SCAN BUTTON 126 AUDIO DISPLAY BUTTON SCAN BUTTON PWR/VOL KNOB EX, EX-V6 and LX-V6 Models without Navigation System LOAD BUTTON CD BUTTON CD LOAD INDICATOR SEEK/SKIP BAR SEEK/SKIP BAR UPPER DISPLAY RDM BUTTON PRESET BAR CD BUTTON EX, EX-V6 Models with Navigation System (U.S.
Main Menu Table of Contents Playing a CD EX-L, EX-V6 Models with Navigation System (U.S.
Main Menu Table of Contents Playing a CD, CD Changer To Play a CD To load or play CDs, the ignition switch must be in the ACCESSORY (I) or ON(II) position. You operate the CD player/CD changer with the same controls used for the radio. To select the CD player/CD changer, press the CD button. The number of the track playing is shown in the display. With the in-dash CD changer, the disc and track numbers are displayed. The system will continuously play a CD until you change modes.
Main Menu Table of Contents Playing a CD, CD Changer For Vehicle with in-dash CD Changer You can also load a CD into an empty position while a CD is playing. Select the empty position (the disc number indicator is not highlighted) and press the appropriate preset bar or touch a disc icon. The current CD stops playing and starts the loading sequence. The CD just loaded will play. You operate the CD changer with the same controls used for the radio.
Main Menu Table of Contents Playing a CD, CD Changer For Vehicles without Navigation System SEEK/SKIP − Push the to play the next track on the disc. Push the once to replay the track in play, press twice to replay the previous track. To remove rapidly within a track, press and hold the , or the button. REPEAT − Press to continuously replay a track. You will see RPT in the display. Press the RPT button again to turn it off. RANDOM − Press to play the tracks in random order.
Main Menu Table of Contents Playing a CD, CD Changer DISC RPT − Touch the icon to continuously replay the current CD. Touch again to turn it off. TRACK RDM − Touch the icon to play the current CD in random order. Touch again to stop. To Stop Playing a CD If a tape is in the optional tape player, press the AUX button to switch to the tape while a CD is playing. Press the CD button again to switch back to the CD player. On models with CD player or changer Press the eject button ( ) to remove the CD.
Main Menu Table of Contents Playing a CD, CD Changer Operating the Optional CD Changer DX, LX, LX-V6, and EX models An optional six or eight disc CD changer is available for your vehicle from your Honda dealer. This disc changer uses the same controls used for the in-dash CD player/changer or the radio. Load the desired CDs in the magazine, and load the magazine in the changer according to the instructions that came with the unit. To select the CD changer, press the CD button.
Main Menu Table of Contents CD Player Error Messages If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer. Error Message or FOCUS Error Mechanical Error High Temperature Solution Press the eject button and pull out the disc. Check if the disc is inserted correctly in the CD player. Make sure the disc is not scratched or damaged. Press the eject button and pull out the disc.
Main Menu Table of Contents CD Changer Error Messages If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer. Error Message Cause FOCUS Error Mechanical Error No CD in the CD Changer High Temperature 134 Solution Press the CD eject button and pull out the CDs. Check for an error indication. Insert the CDs again.
Main Menu Table of Contents Protecting Your CDs General Information When using CD-R discs, use only high quality CDs labeled for audio use. CD-RW discs will not work in this unit. Play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems. Handle your CDs properly to prevent damage and skipping. See this page. To clean a CD, use a clean soft cloth. Wipe across the CD from the center to the outside edge. A new CD may be rough on the inner and outer edges.
Main Menu Table of Contents Playing a Tape (U.S.
Main Menu Table of Contents Playing a Tape (U.S. Vehicles) All U.S. EX Leather Interior Models with Navigation System All U.S.
Main Menu Table of Contents Playing a Tape (U.S. Vehicles) To Play a Tape Optional on all U.S. models The ignition switch must be in ACCESSORY (I) or ON (II). Make sure the open side of the tape is facing right, then insert the tape most of the way into the slot. The system will pull the tape in the rest of the way, and begin to play it. The tape direction indicator will light to show you which side of the tape is playing. The ▲ indicates the side you inserted upward in now playing.
Main Menu Table of Contents Playing a Tape (U.S. Vehicles) SKIP − Press side to find the beginning of the current song or passage. Press side to find the beginning of the next song or passage. When the system reaches the beginning of a song or passage, it begins to play it. REPEAT − Press the RPT button or icon to continuously play a song or passage. You will see RPT displayed. The track will repeat until you press the RPT button or icon again.
Main Menu Table of Contents Playing a Tape (U.S. Vehicles) Caring for the Tape and Player The tape player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. If you do not clean the tape player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit. Your dealer has a cleaning kit available.
Main Menu Table of Contents Playing the XMTM Satellite Radio Satellite Digital Radio EX-L and EX-V6 Models All U.S. EX-L and EX-V6 Models without Navigation System Your vehicle is capable of receiving XMTM Satellite Radio anywhere in the United States except Hawaii, Alaska, and Canada. CATEGORY/CHANNEL MODE INDICATOR CATEGORY/CHANNEL MODE INDICATOR SAT RADIO BUTTON DISP BUTTON AUDIO DISPLAY BUTTON SAT RADIO BUTTON SCAN BUTTON Features XM is a registered trademark of XM Satellite Radio, Inc.
Main Menu Table of Contents Playing the XMTM Satellite Radio To Play XMTM Satellite Radio The ignition must be in the ACCESSORY (I) or ON (II) position. Turn the system on: Vehicles with Navigation System Push any of the following: PWR/ VOL knob, the CD/AUX XM, or AUDIO button. Vehicles without Navigation System Push any of the following: PWR/ VOL knob or the CD/AUX XM button. Turn the PWR/VOL knob to adjust the volume.
Main Menu Table of Contents Playing the XMTM Satellite Radio SCAN − The SCAN function samples all channels for 5 seconds. To activate the function, push the SCAN button. Push it again to get out of the sequence. For Vehicles with Navigation System Once your XM channels are preset, pressing the CH DISC button will select your preset channels. Preset − Each preset icon or button can store one channel in XM1 and one in XM2. 1. Push the CD/AUX XM button. (You will see XM1 or XM2.) 2.
Main Menu Table of Contents Playing the XMTM Satellite Radio Satellite Radio Signals Satellite radio receives signals from two satellites to produce clear, highquality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, satellite radio also allows you to view channel and category selections in the audio display. Signal may be blocked by mountains or large obstacles to the south.
Main Menu Table of Contents Playing the XMTM Satellite Radio Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions: Receiving Satellite Radio Service If your XM Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Satellite Radio.
Main Menu Table of Contents Playing the XMTM Satellite Radio If you decide to purchase XM Satellite Radio service, contact XM Radio at www.xmradio.com, or at 1-800-852-9696. You will need to give them your radio I.D. number and your credit card number. To get your XM Satellite radio ID number: Turn the TUNE knob until ‘‘0’’ appears in the display. Your ID number will appear in the display. After you have registered with XM Radio, keep your audio system in the SAT Radio mode while you await activation.
Main Menu Table of Contents Steering Wheel Controls On EX, EX-L, LX-V6 and EX-V6 models MODE BUTTON The VOL button adjusts the volume up (▲) or down (▼). Press the top or bottom of the button and hold it until the desired volume is reached, then release it. VOL BUTTON CH BUTTON Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel.
Main Menu Table of Contents Radio Theft Protection On EX and EX-V6 models Your vehicle’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code using the preset bars or the TUNE knob. Because there are hundreds of number combinations possible from the five-digit, making the system work without knowing the exact code is nearly impossible.
Main Menu Table of Contents Setting the Clock On models without Navigation System If your vehicle’s battery is disconnected or goes dead, you will need to set the clock. DIGITAL CLOCK PRESET BARS SOUND BUTTON You can quickly set the time to the nearest hour. Pressing and holding the SOUND button, then pressing the R (Preset 6) side of the bar sets the clock back to the previous hour. If the displayed time is after the half hour, the clock sets the clock forward to the beginning of the next hour.
Main Menu Table of Contents Security System On EX, EX-L, LX-V6 and Canadian LX models The security system helps to protect your vehicle and valuables from theft. The horn sounds and a combination of headlights, parking lights, side marker lights and taillights flashes if someone attempts to break into your vehicle or remove the radio. This alarm continues for two minutes, then the system resets.
Main Menu Table of Contents Cruise Control On all models except U.S. DX Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather. Using the Cruise Control CRUISE CONTROL MASTER BUTTON 3. Press and release the DECEL/ SET button on the steering wheel. The CRUISE CONTROL light on the instrument panel comes on to show the system is now activated.
Main Menu Table of Contents Cruise Control The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down. This will cancel the cruise control. To resume the set speed, press the RES/ACCEL button. The CRUISE CONTROL light on the instrument panel will come back on. Changing the Set Speed You can increase the set cruising speed in any of these ways: Press and hold the RES/ACCEL button.
Main Menu Table of Contents Cruise Control Cancelling the Cruise Control You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal. Push the Cruise Control Master Button. Pressing the Cruise Control Master Button turns the system off and erases the previous cruising speed. Features Push the CANCEL button on the steering wheel.
Main Menu Table of Contents HomeLink Universal Transceiver On EX-V6 model The HomeLink Universal Transceiver built into your vehicle can be programmed to operate up to three remote controlled devices around your home, such as garage doors, lighting, or home security systems. General Information If you are training HomeLink to operate a garage door or gate, you should unplug the motor for that device during training. Repeatedly pressing the remote control button could burn out the motor.
Main Menu Table of Contents HomeLink Universal Transceiver If you are training the second or third buttons, go directly to Step 1. 1. Unplug the garage door opener motor from the house current. 2. Hold the end of the garage door opener remote control 2 to 5 inches from HomeLink. Make sure you are not blocking your view of the red indicator in HomeLink.
Main Menu Table of Contents HomeLink Universal Transceiver Canadian Owners: The remote control you are training from may stop transmitting after 2 seconds. This is not enough for HomeLink to learn the code. Release and press the button on the remote control every 2 seconds until HomeLink has learned the code. 4. The red indicator in HomeLink should begin flashing. It will flash slowly at first, then rapidly. 5. When the red indicator flashes rapidly, release both buttons.
Main Menu Table of Contents HomeLink Universal Transceiver 1. Make sure you have properly completed the ‘‘Training HomeLink’’ procedure. TRAINING BUTTON 4. Press and hold the button on HomeLink for 3 to 4 seconds. 6. Press the HomeLink button again. It should operate the garage door. 3. Press the training button on the garage door opener unit until the indicator next to the button comes on, then release it. The indicator may blink, or come on and stay on.
Main Menu Table of Contents HomeLink Universal Transceiver Erasing Codes To erase the codes stored in all three buttons, press and hold the two outside buttons until the red light begins to flash, then release the buttons. You should erase all three codes before selling the vehicle. Retraining a Button To train an already programmed HomeLink button with a new device, you do not have to erase all the memory.
Main Menu Before Driving Break-in Period .............................. 160 Fuel Recommendation .................. 160 Service Station Procedures .......... 162 Refueling..................................... 162 Opening and Closing the Hood ........................................ 163 Oil Check .................................... 165 Engine Coolant Check .............. 166 Fuel Economy ................................ 167 Improving Fuel Economy ......... 167 Accessories and Modifications ....
Main Menu Table of Contents Break-in Period, Fuel Recommendation Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Do not change the oil until the scheduled maintenance time. Avoid hard braking for the first 200 miles (300 km). Do not tow a trailer.
Main Menu Table of Contents Fuel Recommendation Some gasoline today is blended with oxygenates such as ethanol or MTBE. Your vehicle is designed to operate on oxygenated gasoline containing up to 10 percent ethanol by volume and up to 15 percent MTBE by volume. Do not use gasoline containing methanol. If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline. For further important fuel-related information, please refer to your Quick Start Guide.
Main Menu Table of Contents Service Station Procedure Refueling Push Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flames away. Handle fuel only outdoors. Wipe up spills immediately. 1. Park with the driver’s side closest to the gas pump. 4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘top off’’ the tank.
Main Menu Table of Contents Service Station Procedure 5. Screw the fuel fill cap back on until it clicks at least three times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 259 ). Opening and Closing the Hood HOOD RELEASE HANDLE LATCH 6. Push the fuel fill door closed until it latches. 2. Put your fingers under the front edge of the hood near the center. Slide your hand to the left until you feel the hood latch handle. Push this handle up to release it.
Main Menu Table of Contents Service Station Procedure SUPPORT ROD 3. 4-cylinder models Pull the support rod out of its clip and insert the end into the hole on the front of the hood near the center. To Close the Hood: cm) above the fender, then let it drop. Make sure it is securely latched. 6-cylinder models Lift the hood up most of the way. The hydraulic supports will lift it up the rest of the way and hold it up. 4-cylinder models Lift it up slightly to remove the support rod from the hole.
Main Menu Table of Contents Service Station Procedure Oil Check 4-cylinder models DIPSTICK (orange handle) 6-cylinder models DIPSTICK (orange loop) Wait a few minutes after turning the engine off before you check the oil. 2. Wipe the dipstick with a clean cloth or paper towel. 1. Remove the dipstick (orange handle). 3. Insert it all the way back in its hole. 4-cylinder models 4. Remove the dipstick again and check the level. It should be between the upper and lower marks.
Main Menu Table of Contents Service Station Procedure Engine Coolant Check RESERVE TANK MAX RESERVE TANK MAX UPPER MARK LOWER MARK 6-cylinder models MIN 4-cylinder models Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If it is below the MIN line, see Adding Engine Coolant on page 217 for information on adding the proper coolant.
Main Menu Table of Contents Fuel Economy Improving Fuel Economy Always maintain your vehicle according to the maintenance schedule. See Owner’s Maintenance Checks (see page 201 ). The build-up of snow or mud on your vehicle’s underside adds weight and rolling resistance. Frequent cleaning helps your fuel mileage and reduces the chance of corrosion. Try to maintain a constant speed. Every time you slow down and speed up, your vehicle uses extra fuel. Use the cruise control when appropriate.
Main Menu Table of Contents Accessories and Modifications Modifying your vehicle, or installing some non-Honda accessories, can make your vehicle unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Honda accessories that allow you to personalize your vehicle. These accessories have been designed and approved for your vehicle, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifying Your Vehicle Removing parts from your vehicle, or replacing components with aftermarket components could seriously affect your vehicle’s handling, stability, and reliability. Raising your vehicle with an aftermarket suspension kit can affect the handling and stability. Aftermarket wheels, because they are a universal design, can cause excessive stress on suspension components.
Main Menu Table of Contents Carrying Cargo Your vehicle has several convenient storage areas: DOOR POCKET CENTER POCKET Glove box Door and seat-back pockets Trunk, including the back seats when folded down Center pocket Console compartment (on some models) Roof-rack (if installed) However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, and make it unsafe.
Main Menu Table of Contents Carrying Cargo Steps for Determining Correct Load Limit: Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. Follow all load limits and other loading guidelines in this manual. 1. Locate the statement, ‘‘the combined weight of occupants and cargo should never exceed 850 lbs’’ on your vehicle’s placard.
Main Menu Table of Contents Carrying Cargo In addition, the total weight of the vehicle, all passengers and accessories must not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR). Both are on a label on the driver’s doorjamb. If you carry large items that prevent you from closing the trunk lid, exhaust gas can enter the passenger area. To avoid the possibility of carbon monoxide poisoning, follow the instructions on page 52 .
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the manual and automatic transmissions. It also includes important information on parking your vehicle, the braking system, the Traction Control System, and facts you need if you are planning to tow a trailer. 173 Driving Preparing to Drive ......................... 174 Starting the Engine........................ 175 Manual Transmission.................... 176 Recommended Shift Points ......
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments before you drive your vehicle. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 6. Check the seat adjustment (see pages 88 to 90 ). 7. Check the adjustment of the inside and outside mirrors (see pages 94 and 95 ). 8. Check the steering wheel adjustment (see page 74 ). 2. Check that the hood is fully closed. 3. Check that the trunk is fully closed.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. Automatic Transmission: The immobilizer system protects your vehicle f rom thef t. If an improperlycoded key (or other device) is used, the engine’s f uel system is disabled. See Immobilizer System on page 77 . 6.
Main Menu Table of Contents Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the vehicle moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’ The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: Normal acceleration 1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 15 mph (25 km/h) 25 mph (40 km/h) 40 mph (65 km/h) 50 mph (80 km/h) Before downshifting, make sure the engine will not go into the tachometer’s red zone.
Main Menu Table of Contents Automatic Transmission Shift Lever Position Indicators If the malfunction indicator lamp comes on along with the ‘‘D’’ indicator, there is a problem in the automatic transmission control system. Avoid rapid acceleration and have the transmission checked by your dealer as soon as possible. To shift from: P to R Shifting SHIFT LEVER These indicators between the tachometer and speedometer show which position the shift lever is in.
Main Menu Table of Contents Automatic Transmission Park (P) − This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Press the release button on the side of the shift lever to move it. You must also press the release button to shift into Park. To avoid transmission damage, come to a complete stop before shifting into Park.
Main Menu Table of Contents Automatic Transmission Second (2) − This position locks the transmission in second gear. It does not downshift to first gear when you come to a stop. Use Second gear: For more power when climbing. To increase engine braking when going down steep hills. For starting out on a slippery surface or in deep snow. To help reduce wheel spin. When driving downhill with a trailer. 180 First (1) − To shift from Second to First, press the release button on the side of the shift lever.
Main Menu Table of Contents Automatic Transmission Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. COVER 4. Insert the key in the Shift Lock Release slot. 1. Set the Parking brake. 2. Remove the key from the ignition switch. Driving 3. Put a cloth on the edge of the Shift Lock Release slot cover next to the shift lever.
Main Menu Table of Contents Automatic Transmission RELEASE BUTTON SHIFT LOCK RELEASE SLOT 5. Push down on the key while you press the release button on the shift lever and move the shift lever out of Park to Neutral. 6. Remove the key from the Shift Lock Release slot, then reinstall the cover. Make sure the notch on the cover is on the left side. Depress the brake pedal and restart the engine. 182 If you need to use the Shift Lock Release, it means your vehicle is developing a problem.
Main Menu Table of Contents Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly or your vehicle may roll if it is parked on an incline. Parking Tips Make sure the moonroof (if equipped) and the windows are closed. Turn off the lights. If your vehicle has a manual transmission, put it in first gear. Place any packages, valuables, etc., in the trunk or take them with you. Lock the doors with the key or the remote transmitter.
Main Menu Table of Contents Braking System Your vehicle is equipped with disc brakes. The brakes on the rear wheels may be disc or drum, depending on the model. A power assist helps reduce the effort needed on the brake pedal. The ABS helps you retain steering control when braking very hard. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, increases wear and reduces their effectiveness.
Main Menu Table of Contents Anti-lock Brakes (ABS) Anti-lock Brakes (ABS) The Anti-lock Brake System (ABS) helps prevent the brakes from locking up and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it. The ABS also balances the front-torear braking distribution according to vehicle loading. ABS Indicator If the ABS indicator comes on, the anti-lock function of the braking system has shut down.
Main Menu Table of Contents Anti-lock Brakes (ABS) steering control during braking. ABS INDICATOR ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe speed for the road and weather conditions. Test your brakes as instructed on page 261 . If the brakes feel normal, drive slowly and have your vehicle repaired by your Honda dealer as soon as possible.
Main Menu Table of Contents Traction Control System On LX-V6 and EX-V6 models Your vehicle is equipped with a Traction Control System (TCS) to assist you in maintaining traction while driving slowly on loose or slippery surfaces. Driving with TCS requires no special skills or technique. The TCS does not control your vehicle’s whole braking system and cannot prevent skidding if you enter a corner too fast.
Main Menu Table of Contents Traction Control System TCS ON/OFF Switch Deactivate the system by pressing the TCS On/Off switch. The TCS Activation indicator comes on as a reminder. Pressing the switch again turns the system back on. The TCS turns on every time you start the engine, even if you turned it off the last time you drove the vehicle. This switch is under the side vent. It lets you turn the TCS on and off. You cannot turn off the TCS while the TCS Activation indicator is flashing.
Main Menu Table of Contents Traction Control System If the TCS indicator comes on while driving, pull to the side of the road when it is safe and turn off the engine. Reset the system by restarting the engine, and watch the TCS indicator. If the TCS indicator remains on, or comes back on while driving, have the TCS inspected by your dealer. You can still drive the vehicle without TCS.
Main Menu Table of Contents Towing a Trailer Your vehicle has been designed to primarily carry passengers and their cargo. You can also use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Exceeding any load limit or improperly loading your vehicle and trailer can cause a crash in which you can be seriously hurt or killed. Check the loading of your vehicle and trailer carefully before starting to drive.
Main Menu Table of Contents Towing a Trailer To achieve a proper tongue load, start by loading 60 percent of the load toward the front of the trailer and 40 percent toward the rear, then re-adjust the load as needed.
Main Menu Table of Contents Towing a Trailer Towing Equipment and Accessories Towing can require a variety of equipment, depending on the size of your trailer, how it will be used, how much load you are towing, and where you tow. Discuss your needs with your trailer sales or rental agency, and follow the guidelines in the rest of this section. Also make sure that all equipment is properly installed and that it meets federal, state, province, and local regulations.
Main Menu Table of Contents Towing a Trailer Trailer Lights Additional Towing Equipment Trailer lights and equipment must comply with federal, state, and local regulations. Check with your local recreational vehicle dealer for the requirements in your area, and use only equipment designed for your vehicle. Many states and Canadian provinces require special outside mirrors when towing a trailer.
Main Menu Table of Contents Towing a Trailer Pre-Tow Checklist When preparing to tow, and before driving away, be sure to check the following: The vehicle has been properly serviced, and the tires, brakes, suspension, cooling system, and lights are in good operating condition. All weights and loads are within limits (see pages 190 and 191 ). The hitch, safety chains, and any other attachments are secure. All items in or on the trailer are properly secured and cannot shift while you drive.
Main Menu Table of Contents Towing a Trailer Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle’s handling and performance, so driving with a trailer requires some special driving skills and techniques. Towing Speeds and Gears Drive slower than normal in all driving situations, and obey posted speed limits for vehicles with trailers. If you have an automatic transmission, use D position when towing a trailer on level roads.
Main Menu 196
Main Menu Maintenance This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. Timing Belt ..................................... 225 Hood Latch ..................................... 225 Lights .................................
Main Menu Table of Contents Maintenance Safety All service items not detailed in this section should be performed by a certified technician or other qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required. Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off. To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.
Main Menu Table of Contents Maintenance Schedule The maintenance schedule assumes you will use your vehicle as normal transportation for passengers and their possessions. You should also follow these recommendations: Avoid exceeding your vehicle’s load limit. This puts excess stress on the engine, brakes, and many other vehicle parts. The load limit is shown on the tire information label on the driver’s doorjamb. Drive your vehicle regularly over a distance of several miles (kilometers).
Main Menu Table of Contents Maintenance Schedule Servicing Your Vehicle Your authorized dealer knows your vehicle best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or skilled person to keep your warranties in effect. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record.
Main Menu Table of Contents Maintenance Schedule Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed. Engine oil level − Check every time you fill the fuel tank. See page 165 . Tires − Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 236 .
Main Menu Table of Contents Maintenance Schedule for Normal Conditions 4-cylinder Models Check engine oil and coolant Check tires Replace engine oil Rotate tires (follow pattern on page 239 ) Replace engine oil filter Check front and rear brakes Check parking brake adjustment Inspect the following items: Tie-rod ends, steering gearbox, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system＃ Fuel lines and connections
Main Menu Table of Contents 4-cylinder Models 150 240 Every 10,000 miles (16,000 km) or every 1 year, whichever comes first Every 20,000 miles (32,000 km) or every 1 year, whichever comes first Every 30,000 miles (48,000 km) or every 2 years, whichever comes first Every 15,000 miles (24,000 km) (Use normal schedule except in dusty conditions) Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy Every 60,000 miles (96,000 km) or every 3 years, whichever comes first Every 160,000 mile
Main Menu Table of Contents Maintenance Schedule for Normal Conditions 6-cylinder Models Check engine oil and coolant Check tires Replace engine oil Rotate tires (follow pattern on page 239 ) Replace engine oil filter Check front and rear brakes Check parking brake adjustment Inspect the following items: Tie-rod ends, steering gearbox, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system＃ Fuel lines and connections
Main Menu Table of Contents 6-cylinder Models ＃: ＊1: ＊2: ＊3: 150 240 Maintenance Schedule for Severe Conditions Check engine oil and coolant Check tires Replace engine oil and oil filter Rotate tires (follow pattern on page 239 ) Check front and rear brakes Inspect the following items: Tie-rod ends, steering gearbox, and boots Suspension components Driveshaft boots Check parking brake adjustment Lubricate all hinges, locks and latches Inspect the following items: Brake hoses and lines (including ABS)
Main Menu Table of Contents Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (pages 202 , 204 ) or severe conditions (pages 203 , 205 ). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Maintenance Record (for Normal and Severe Schedules) 41,250 mi 66,000 km Signature or dealer stamp mi/km 63,750 mi 102,000 km Date 45,000 mi 72,000 km mi/km mi/km 65,000 mi 104,000 km mi/km 67,500 mi 108,000 km mi/km 70,000 mi 112,000 km 71,250 mi 114,000 km Date 75,000 mi 120,000 km Date 56,250 mi 90,000 km mi/km mi/km Date mi/km Date 78,750 mi 126,000 km Date 60,000 mi 96,000 km mi/km Maintenance mi/km mi/km Date Date 55,000 mi 88,000 km mi/km Date Da
Main Menu Table of Contents Maintenance Record (for Normal and Severe Schedules) 82,500 mi 132,000 km Signature or dealer stamp mi/km 101,250 mi 162,000 km Date 85,000 mi 136,000 km mi/km mi/km 105,000 mi 168,000 km mi/km 108,750 mi 174,000 km mi/km 110,000 mi 176,000 km mi/km 112,500 mi 180,000 km mi/km 115,000 mi 184,000 km mi/km Date 208 mi/km Date 116,250 mi 186,000 km Date 100,000 mi 166,000 km mi/km Date Date 97,500 mi 156,000 km mi/km Date Date 95,000 mi 152,000 km mi/km Da
Main Menu Table of Contents Maintenance Record (for Normal and Severe Schedules) 123,750 mi 198,000 km Signature or dealer stamp mi/km 142,500 mi 228,000 km Date 125,000 mi 200,000 km mi/km mi/km 145,000 mi 232,000 km mi/km Date 146,250 mi 234,000 km mi/km Date 150,000 mi 240,000 km mi/km Date mi/km Maintenance 131,250 mi 210,000 km mi/km Date Date 130,000 mi 208,000 km mi/km Date Date 127,500 mi 204,000 km Signature or dealer stamp Date 135,000 mi 216,000 km mi/km Date 138,750 mi 2
Main Menu Table of Contents Fluid Locations 4-cylinder Models BRAKE FLUID (Gray cap) CLUTCH FLUID (5-speed Manual Transmission only) (Light gray cap) ENGINE OIL DIPSTICK (Orange handle) ENGINE OIL FILL CAP WASHER FLUID (Blue cap) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) POWER STEERING FLUID (Red cap) COOLANT RESERVOIR RADIATOR CAP 210
Main Menu Table of Contents Fluid Locations 6-cylinder Models ENGINE OIL FILL CAP ENGINE OIL DIPSTICK (Orange loop) BRAKE FLUID (Gray cap) Maintenance AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP 211
Main Menu Table of Contents Adding Engine Oil ENGINE OIL FILL CAP ENGINE OIL FILL CAP 4-cylinder models 6-cylinder models Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill. Clean up any spills immediately. Spilled oil could damage components in the engine compartment. 212 Install the engine oil fill cap and tighten it securely. Wait a few minutes and recheck the oil level.
Main Menu Table of Contents Adding Engine Oil Honda Motor Oil is the preferred 5W-20 lubricant for your vehicle. It is highly recommended that you use Honda Motor Oil in your vehicle for optimum engine protection. Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’ The oil viscosity or weight is provided on the container’s label. 5W-20 oil is formulated for yearround protection of your Honda to improve cold weather starting and fuel economy.
Main Menu Table of Contents Changing the Oil and Filter Always change the oil and filter according to the recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service stationtype hydraulic lift for this service.
Main Menu Table of Contents Changing the Oil and Filter OIL FILTER OIL FILTER 7. Replace the engine oil fill cap. Start the engine. The oil pressure indicator should go out within 5 seconds. If it does not, turn off the engine and check your work. 8. Let the engine run for several minutes, then check the drain bolt and oil filter for leaks. 4-cylinder models 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: (4-cylinder models) 33 lbf·ft (45 N·m , 4.
Main Menu Table of Contents Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal use. LEVEL GAUGE LEVEL GAUGE Check the reservoir’s fluid level by removing the cap and looking at the level gauge attached to the cap. Canadian Models: The low washer level indicator will light when the level is low (see page 63 ). Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.
Main Menu Table of Contents Engine Coolant Adding Engine Coolant 4-cylinder models RESERVE TANK RESERVE TANK Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator cap. 217 Maintenance If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to MAX line. Inspect the cooling system for leaks.
Main Menu Table of Contents Engine Coolant 6. Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank. RADIATOR CAP Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components. 4-cylinder models 1. Make sure the engine and radiator are cool. 2.
Main Menu Table of Contents Transmission Fluid marks. Automatic Transmission 4-cylinder models 5. If the level is below the lower mark, remove the fill plug and add fluid into the tube to bring it to the upper mark. DIPSTICK Check the fluid level with the engine at normal operating temperature. 1. Park the vehicle on level ground. Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth. 3. Insert the dipstick all the way into the transmission.
Main Menu Table of Contents Transmission Fluid To thoroughly flush the transmission, the technician should drain and refill it with Honda ATF-Z1 (Automatic Transmission Fluid), then drive the vehicle for a short distance. Do this three times. Then drain and refill the transmission a final time. 6. Insert the dipstick all the way back into the transmission securely as shown in the illustration.
Main Menu Table of Contents Transmission Fluid 5. If the level is below the lower mark, remove the fill plug and add fluid into the tube to bring it to the upper mark. Pour the fluid slowly and carefully so you do not spill. Clean up any spill immediately; it could damage components in the engine compartment. 3. Insert the dipstick all the way into the transmission. Make sure the rubber cap fits in the dipstick guide and the dipstick is down all the way. 4. Remove the dipstick and check the fluid level.
Main Menu Table of Contents Transmission Fluid 6. Insert the dipstick all the way back into the transmission. Manual Transmission FILLER BOLT The transmission should be drained and refilled with new fluid according to the time and distance recommendations in the maintenance schedule. If you are not sure how to add fluid, contact your dealer. Correct level Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground.
Main Menu Table of Contents Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are up to two reservoirs, depending on the model. They are: Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission only) Replace the brake fluid according to the recommendations in the maintenance schedule. Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement.
Main Menu Table of Contents Brake and Clutch Fluid, Power Steering Fluid Clutch Fluid Power Steering Fluid UPPER LEVEL MAX MIN The fluid level should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system. Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.
Main Menu Table of Contents Power Steering Fluid, Timing Belt Always use Honda Power Steering Fluid. You may use another power steering fluid as an emergency replacement, but have the power steering system flushed and refilled with Honda PSF as soon as possible. A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently, and have the system inspected as soon as possible.
Main Menu Table of Contents Lights Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the trunk or pull a trailer, readjustment may be required. Adjustments should be performed by your dealer or other qualified mechanic. 226 Replacing a Headlight Bulb Your vehicle has two bulbs on each side, four in total. Make sure you are replacing the bulb that is burned out. Your vehicle uses halogen headlight bulbs.
Main Menu Table of Contents Lights High Beam Headlight FASTENERS AIR INTAKE COVER BULB AIR INTAKE COVER FASTENERS 4-cylinder models 2. Remove the electrical connector from the bulb by squeezing the connector to unlock the tab, then slide the connector off the bulb. 4-cylinder models TAB 3. Remove the bulb by turning it approximately one-quarter turn counterclockwise. 4. Install the new bulb and turn it one-quarter turn clockwise to lock it in place. CONTINUED 227 Maintenance 1. Open the hood.
Main Menu Table of Contents Lights Low Beam Headlight BULB HOLDING CLIPS TAB 6-cylinder models 5. Push the electrical connector onto the bulb. 6. Turn on the headlights to test the new bulb. 7. (Passenger’s side) Reinstall the air intake cover. Reinstall the two fasteners and secure them by pushing on the heads until they lock. 228 BULB 1. To change the passenger’s side bulb, start the engine, turn the steering wheel all the way to the left, and turn off the engine.
Main Menu Table of Contents Lights 6. Install the new bulb and turn it one-quarter turn clockwise to lock it in place. 7. Push the electrical connector onto the bulb. Replacing the Front Side Marker/ Turn Signal and Parking Light Bulb HOLDING CLIPS 8. Turn on the headlights to test the new bulb. BULB 1. To change the passenger’s side bulb, start the engine, turn the steering wheel all the way to the left, and turn off the engine. To change the driver’s side bulb, turn the steering wheel to the right.
Main Menu Table of Contents Lights 5. To remove the burned out bulb, push it in and turn it counterclockwise until it unlocks. Replacing Rear Bulbs (in Fenders) BULBS 6. Install the new bulb and turn it clockwise to lock it in place. 5. Test the new bulb to make sure it works. 7. Insert the socket into the headlight assembly. Turn it clockwise to lock it in place. 6. Reinstall the light assembly cover. 8. Test the new bulb to make sure it works. SOCKETS COVER 9.
Main Menu Table of Contents Lights Replacing Rear Bulbs (in Trunk Lid) SOCKETS BULBS 1. Open the trunk. 2. 6-cylinder models Remove the trim clips from the right or left corner of the trunk lid trim by carefully prying them using a small, flat-tip screwdriver wrapped with tape. SOCKETS BULBS 3. Carefully bend back the corner of the trunk lid trim to expose the bulbs. 5. Install a new bulb into the socket, and reinstall the socket into the light assembly. 4.
Main Menu Table of Contents Lights Replacing a High-mount Brake Light Bulb BULB SOCKET 1. Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 2. Remove the burned-out bulb by pulling it straight out of the socket. 3. Install the new bulb and reinstall the socket.
Main Menu Table of Contents Seat Belts, Floor Mats, Dust and Pollen Filter Seat Belts Floor Mats LOOP If you use an aftermarket floor mat, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat. Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system/climate control system.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or if they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace a wiper blade: 1. Raise the wiper arm off the windshield. Raise the driver’s side first, then the passenger’s side.
Main Menu Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. REINFORCEMENT 4. Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade. Maintenance 3.
Main Menu Table of Contents Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced. Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.
Main Menu Table of Contents Tires If you check air pressures when the tires are hot (driven for several miles), you will see readings 4 to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated. While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.
Main Menu Table of Contents Tires Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. INDICATOR LOCATION MARKS You should look for: Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Excessive tread wear. TREAD WEAR INDICATORS Your tires have wear indicators molded into the tread.
Main Menu Table of Contents Tires Tire Rotation Front Front (For Non-directional (For Directional Tires and Wheels) Tires and Wheels) 4-cylinder models 6-cylinder models Every 10,000 miles (16,000 km) Every 7,500 miles (12,000 km) Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall).
Main Menu Table of Contents Tires If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels. Replacement wheels are available at your dealer. Wheels and Tires Wheel: DX and LX models 15 x 6 1/2 JJ All EX models 16 x 6 1/2 JJ Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tires recommended in this owner’s manual.
Main Menu Table of Contents Tires Tire Chains Mount snow chains on your tires when required by driving conditions or local laws. Install them only on the front tires. Because your vehicle has limited tire clearance, Honda strongly recommends using the chains listed below, made by Security Chain Company (SCC). When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension.
Main Menu Table of Contents Checking the Battery TEST INDICATOR WINDOW TEST INDICATOR WINDOW If additional battery maintenance is needed, see your dealer or a qualified technician. WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds. Wash your hands after handling. 4-cylinder models Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.
Main Menu Table of Contents Checking the Battery, Vehicle Storage The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Vehicle Storage If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road.
Main Menu Table of Contents Vehicle Storage Leave the parking brake off. Put the transmission in Reverse (5-speed manual) or Park (automatic). Block the rear wheels. If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground. Leave one window open slightly (if the vehicle is being stored indoors). Disconnect the battery. Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.
Main Menu Taking Care of the Unexpected This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed. 245 Taking Care of the Unexpected Compact Spare Tire....................... 246 Changing a Flat Tire ...............
Main Menu Table of Contents Compact Spare Tire Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can. Do not mount snow chains on the compact spare tire. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm ) Do not use your compact spare tire on another vehicle unless it is the same make and model.
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area that is far away from the traffic lanes. 3. The tools are in the trunk. Open the trunk and raise the trunk floor by lifting up on the back edge. TRUNK FLOOR 4. Take the tool kit out of the trunk. 5. Unscrew the wing bolt and take the spare tire out of its well.
Main Menu Table of Contents Changing a Flat Tire JACK 6. The jack is behind a cover in the right fender. Remove the cover by turning the handle counterclockwise, then pulling on the cover. 7. Turn the jack’s end bracket counterclockwise to loosen it, then remove the jack. 8. Loosen each wheel nut 1/2 turn with the wheel wrench. 248 JACKING POINT 9. Place the jack under the jacking point nearest the tire you need to change.
Main Menu Table of Contents Changing a Flat Tire EXTENSION WHEEL WRENCH U.S. DX, LX and DX, LX-G model in Canada: BRAKE HUB 12.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving. Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. The wheel cover cannot be removed without first removing the wheel nuts. CONTINUED 249 Taking Care of the Unexpected 10.
Main Menu Table of Contents Changing a Flat Tire 16.Remove the center cap before storing the flat tire in the trunk well. WING BOLT 17.Place the flat tire face down in the spare tire well. For For spare normal tire tire SPACER CONE 13.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten them fully. 14.Lower the vehicle to the ground and remove the jack.
Main Menu Table of Contents Changing a Flat Tire, If the Engine Won’t Start Loose items can fly around the interior in a crash and could seriously injure the occupants. Store the wheel, jack, and tools securely before driving. 21.Store the wheel cover or center cap in the trunk. Make sure it does not get scratched or damaged.
Main Menu Table of Contents If the Engine Won’t Start Turn the ignition switch to START (III). If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem (see Emergency Towing on page 263 ).
Main Menu Table of Contents Jump Starting Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. To jump start your vehicle: 1. Open the hood, and check the physical condition of the battery. In very cold weather, check the condition of the electrolyte. If it seems slushy or frozen, do not try jump starting until it thaws.
Main Menu Table of Contents Jump Starting 3. Connect one jumper cable to the positive (＋) terminal on your battery. Connect the other end to the positive (＋) terminal on the booster battery. BOOSTER BATTERY 6-cylinder models 4-cylinder models 4. Connect the second jumper cable to the negative (−) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.
Main Menu Table of Contents Jump Starting 7. Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery. 6-cylinder models Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short. Taking Care of the Unexpected 5.
Main Menu Table of Contents If the Engine Overheats The pointer of the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.). If your vehicle overheats, you should take immediate action. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood.
Main Menu Table of Contents If the Engine Overheats 6. If you do not find an obvious leak, check the coolant level in the radiator reserve tank. Add coolant if the level is below the MIN mark. 7. If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the temperature gauge, or lower, before checking the radiator. 9.
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped. 1. Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators. This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure.
Main Menu Table of Contents Charging System Indicator, Malfunction Indicator Lamp Charging System Indicator Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows. Keep the engine running; starting the engine will discharge the battery rapidly. Go to a service station or garage where you can get technical assistance.
Main Menu Table of Contents Malfunction Indicator Lamp If you have recently refueled your vehicle, the cause of this indicator coming on could be a loose or missing fuel fill cap. Check the cap or replace it. Tightening the cap will not make the indicator turn off immediately; it takes at least three days of normal driving. Readiness Codes Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR＊ ＊ U.S. indicator shown Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Emergency Towing on page 263 ). If you must drive the vehicle a short distance in this condition, drive slowly and carefully.
Main Menu Table of Contents Closing the Moonroof On EX and EX-V6 models If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 265 ). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the trunk. 4.
Main Menu Table of Contents Emergency Towing If your vehicle needs to be towed, call a professional towing service or an organization. Never tow your vehicle with just a rope or chain. It is very dangerous. There are two ways to tow your vehicle. Flat-bed Equipment − The operator loads your vehicle on the back of a truck. This is the best way to transport your vehicle.
Main Menu Table of Contents Emergency Towing With the front wheels on the ground, it is best to tow the vehicle no farther than 50 miles (80 km), and keep the speed below 35 mph (55 km/h). If your vehicle is equipped with a front spoiler, remove it before towing so it is not damaged. Trying to lif t or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight.
Main Menu Table of Contents Fuses INTERIOR UNDER-HOOD TAB The under-hood fuse box is located near the back of the engine compartment on the driver’s side. To open it, push the tabs as shown. 1. Turn the ignition switch to LOCK (0). Make sure the headlights and all other accessories are off. 2. Remove the cover from the fuse box. CONTINUED 265 Taking Care of the Unexpected The interior fuse box is on the driver’s lower left side.
Main Menu Table of Contents Fuses BLOWN 3. Check each of the large fuses in the under-hood fuse box by looking at the wire inside. Removing these fuses requires a Phillips-head screwdriver. BLOWN BLOWN 4. Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse box by pulling out each fuse with the fuse puller provided in the under-hood fuse box. 5. Look for a burned wire inside the fuse.
Main Menu Table of Contents Fuses FUSE PULLER Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating. 6. If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem with your vehicle. Leave the blown fuse in that circuit, and have your vehicle checked by a qualified mechanic.
Main Menu Table of Contents Fuses UNDER-HOOD FUSE/RELAY BOX No. Amps. No. Amps. 1 2 3 4 5 268 10 A (30A) 10 A 15 A 10 A Circuits Protected Left Headlight Low (Rear Defroster Coil) Left Headlight Hi Small Light Right Headlight Hi No. Amps. 6 7 8 9 10 10 A 7.5 A 15 A 20 A − Circuits Protected Right Headlight Low Back Up FI ECU Condenser fan Not Used 11 11＊ 12 13 14 15 16 17 17＊ 18 18＊ 19 20 21 22 20 A 30 A 7.
Main Menu Table of Contents Fuses INTERIOR FUSE BOX No. Amps. 1＊1 2 3＊2 4 5 6 (15 A) 15 A (10 A) 15 A 10 A 7.5 A Circuits Protected Drive by Wire Ignition Coil Day Light Laf Heater Radio Interior Light No. Amps. 7 8 9 10 11 12 10 A 20 A 15 A 7.5 A 30 A − Circuits Protected Back-Up Lights Door Lock Front Accessory Sockets IG OPDS IG Wiper Not Used (20 A) (20 A) (20 A) (20 A) (20 A) 15 A 15 A 7.5 A 7.5 A 10 A 7.5 A 20 A 20 A 20 A 20 A (20 A) − 7.5 A − 7.5 A 7.
Main Menu 270
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your vehicle, and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Three Way Catalytic Converter ............................ 283 Replacement Parts..................... 283 Three Way Catalytic Converter ... 284 State Emissions Testing ............... 285 Technical Information Identification Numbers ......
Main Menu Table of Contents Identification Numbers Your vehicle has several identifying numbers in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped into the engine block. It is on the front. 4-cylinder Models AUTOMATIC TRANSMISSION NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents Specifications Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating Air Conditioning Refrigerant type Charge quantity Lubricant type Capacities Fuel tank ＊1 : 6-cylinder models 189.5 in (4,813 mm) 71.7 in (1,820 mm) 57.2 in (1,453 mm) 107.9 in (2,740 mm) 61.1 in (1,553 mm) 61.2 in (1,554 mm) See the certification label attached to the driver’s doorjamb. HFC-134a (R-134a) 25−27 oz (700−750 g) 16−18 oz (450−500 g)＊1 ND-OIL8 Approx.
Main Menu Table of Contents Specifications Lights Headlights High Low Front turn signal/ Front parking lights Rear turn signal lights Stop/Taillights Taillights High-mount brake light Back-up lights License plate light Ceiling light Spotlights Spotlights/Front ceiling lights Trunk light Door courtesy light Vanity mirror lights ＊1 : LX ＊2 : EX Fuses Interior Under-hood Engine Type Bore x Stroke 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V − − − − − − − − − − − − 21 W (Amber) 21/5 W 2
Main Menu Table of Contents Specifications Tires Size Front/Rear Pressure Spare Front Rear Spare ＊1 : DX ＊2 : LX ＊3 : All EX and V6 models 276 P195/65R15 89H ＊1 P205/65R15 92H ＊2 P205/60R16 91V ＊3 T135/90D15 32 psi (220 kPa , 2.2 kgf/cm 30 psi (210 kPa , 2.1 kgf/cm 30 psi (210 kPa , 2.1 kgf/cm 29 psi (200 kPa , 2.0 kgf/cm 60 psi (420 kPa , 4.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Traction − AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) Temperature − A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Tire Labeling 16 − Rim diameter in inches. Tire Labeling The tires that came on your vehicle have a number of markings. Those you should be aware of are described below. 91 − Load index (a numerical code associated with the maximum load the tire can carry). Tire Size V Whenever tires are replaced, they should be replaced with tires of the same size. Following is an example of tire size with an explanation of what each component means.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel’s contents.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. Technical Information If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your vehicle’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, ignition timing control, exhaust gas recirculation and three way catalytic converter. These four systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent. The three way catalytic converter must operate at a high temperature for the chemical reactions to take place.
Main Menu Table of Contents State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the onboard diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Main Menu Table of Contents State Emissions Testing Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway in D (A/T) or 5th (M/T). Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
Main Menu Warranty and Customer Relations 287 Warranty and Customer Relations Customer Service Information..... 288 Warranty Coverages ..................... 289 Reporting Safety Defects (U.S. Vehicle) ............................. 290 Authorized Manuals ......................
Main Menu Table of Contents Customer Service Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The service manager or general manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new vehicle is covered by these warranties: Emissions Control Systems Defects Warranty and Emissions Performance Warranty − these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional. Please read the warranty manual for exact information. Original Equipment Battery Limited Warranty − this warranty gives up to 100 percent credit toward a replacement battery.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc. 290 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The publications shown below can be purchased from Helm Incorporated. You can order in any of three ways: Detach and mail the order form on the right half of this page Call Helm Inc. at 1-800-782-4356 (credit card orders only) Go online at www. helminc. com If you are interested in other years or models, contact Helm Inc. at 1-800-782-4356.
Main Menu Table of Contents Authorized Manuals NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention the shipment should be sent. For purchases outside U.S.A. please write to the address shown below for a quotation. Ｓ Ｈ Ｉ Ｐ Ｔ Ｏ Customer Name Attention Street Address − No P.O.
Main Menu Index A Battery Charging System Indicator............................ 58, 259 Jump Starting ............................. 253 Maintenance ............................... 242 Specifications ............................. 275 Before Driving ............................... 159 Belts, Seat ......................................... 10 Brakes Anti-lock System (ABS) ............ 185 Break-in, New Linings .............. 160 Bulb Replacement ..................... 231 Fluid ................................
Main Menu Index Child Seats ........................................ 34 Lower Anchorage Points ............ 43 Tether Anchorage Points ........... 47 Climate Control Sensors ............... 117 Clock, Setting the .......................... 149 Clutch Fluid .................................... 224 CO in the Exhaust ......................... 280 Cold Weather, Starting in ............. 175 Compact Spare ............................... 246 Console Compartment .................. 103 Consumer Information........
Main Menu Index Evaporative Emissions Controls .. 282 Exhaust Fumes ................................ 52 Expectant Mothers, Use of Seat Belts by ......................................... 18 F G Gas Mileage, Improving................ 167 Gasohol ........................................... 280 Gasoline .......................................... 160 Gauge ............................................ 66 Octane Requirement ................. 160 Tank, Filling the.........................
Main Menu Index I Identification Number, Vehicle.... 272 Ignition Keys............................................... 75 Switch ............................................ 78 Timing Control System ............. 283 Immobilizer System......................... 77 Important Safety Precautions .......... 8 Indicators, Instrument Panel .......... 58 Infant Restraint ................................ 39 Infant Seats ....................................... 39 Tether Anchorage Points ...........
Main Menu Index N Neutral Gear Position.................... 179 New Vehicle Break-in ................... 160 Normal Shift Speeds...................... 177 NOTICE, Explanation of .................... i Numbers, Identification ................ 272 O P Panel Brightness Control ............... 72 Park Gear Position......................... 178 Parking Brake .................................. 99 Parking Lights.................................. 70 Parking Over Things that Burn ... 284 Parking Tips ............
Main Menu Index Reverse Gear Position................... 179 Rotation, Tire ................................. 239 S Safety Belts....................................... 10 Safety Defects, Reporting............. 290 Safety Features .................................. 9 Airbags .......................................... 11 Seat Belts ...................................... 10 Safety Labels, Location of .............. 53 Safety Messages ................................ ii Satellite Radio........................
Main Menu Index Supplemental Restraint System................................. 11, 23 Servicing ....................................... 32 SRS Indicator.......................... 30, 58 System Components.................... 23 Synthetic Oil ................................... 213 T Shifting the Automatic .............. 178 Shifting the Manual ................... 176 Treadwear ...................................... 277 Trip Meter ........................................ 65 Trunk...........................
Main Menu Index Vehicle Identification Number..... 272 Vehicle Storage .............................. 243 VIN .................................................. 272 Viscosity, Oil................................... 213 W WARNING, Explanation of .............. ii Warning Labels, Location of .......... 53 Warranty Coverages ..................... 289 Washer, Windshield Checking the Fluid Level ......... 215 Operation ...................................... 69 Wheels Adjusting the Steering ................
Main Menu Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 86 or higher. Fuel Tank Capacity: 17.09 US gal (64.7 ) Recommended Engine Oil: API Premium grade 5W-20 detergent oil (see page 213 ). Oil change capacity (including filter): 4-cylinder models 4.4 US qt (4.2 ) 6-cylinder models 4.5 US qt (4.3 ) Automatic Transmission Fluid: Honda ATF-Z1 (Automatic Transmission Fluid) preferred, or a DEXRON III ATF as a temporary replacement (see pages 219 and 220 ).
