2006 CR-V Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ......................................................................................................................................... i A Few Words About Safety....................................................................................
Main Menu Owner’s Identification This owner’s manual should be considered a permanent part of the vehicle and should remain with the vehicle when it is sold. OWNER This owner’s manual covers all models of the CR-V. You may find descriptions of equipment and features that are not on your particular vehicle. ADDRESS STREET CITY STATE/PROVINCE ZIP CODE/ POSTAL CODE V. I. N.
Main Menu Introduction Congratulations! Your selection of a 2006 Honda CR-V was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new vehicle is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your vehicle so you can refer to it at any time. As you read this manual, you will find information that is preceded by a symbol.
Main Menu A Few Words About Safety Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining your vehicle.
Main Menu Important Handling Information Your CR-V has higher ground clearance than a passenger vehicle designed for use only on pavement. Higher ground clearance has many advantages for off-highway driving. It allows you to travel over bumps, obstacles, and rough terrain. It also provides good visibility so you can anticipate problems earlier. These advantages come at some cost. Because your vehicle is taller and rides higher off the ground, it has a high center of gravity.
Main Menu Your Vehicle at a Glance MIRROR CONTROLS (P.89) DRIVER’S FRONT AIRBAG (P.9 , 23) INSTRUMENT PANEL INDICATORS (P.55) GAUGES (P.61) AUTOMATIC TRANSMISSION (P.161) MANUAL TRANSMISSION (P.159) Your Vehicle at a Glance POWER DOOR LOCK MASTER SWITCH (P.73) AUDIO SYSTEM (P.103) PASSENGER AIRBAG OFF INDICATOR (P.30) FRONT PASSENGER AIRBAG (P.9 , 23) POWER WINDOW SWITCHES (P.86) HAZARD WARNING BUTTON (P.67) PARKING BRAKE (P.68) HEATING/COOLING CONTROLS (P.98) HATCH GLASS RELEASE BUTTON (P.
Main Menu Your Vehicle at a Glance HEADLIGHTS/TURN SIGNALS (P.66) INSTRUMENT PANEL BRIGHTNESS (P.67) SHIFT LEVER (A/T) (P.161) AUDIO SYSTEM (P.103) CLOCK (P.137) REMOTE AUDIO CONTROLS*2 (P.135) PASSENGER AIRBAG OFF INDICATOR (P.30) VEHICLE STABILITY ASSIST (VSA) SYSTEM ON/OFF SWITCH (P.171) WINDSHIELD WIPERS/WASHERS (P.65) MOONROOF SWITCH*2 (P.88) HAZARD WARNING BUTTON (P.67) CRUISE CONTROL MASTER BUTTON (P.138) A/T model is shown. *1 : *2 : 4 REAR WINDOW DEFOGGER (P.
Main Menu Driver and Passenger Safety Important Safety Precautions .......... 6 Your Vehicle’s Safety Features........ 7 Protecting Adults and Teens.......... 11 1. Close and Lock the Doors ...... 11 2. Adjust the Front Seats ............ 11 3. Adjust the Seat-Backs ............. 12 4. Adjust the Head Restraints .... 13 5. Fasten and Position the Seat Belts .............................. 14 6. Maintain a Proper Sitting Position ................................. 15 Advice for Pregnant Women......
Main Menu Table of Contents Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags are designed to supplement seat belts, not replace them.
Main Menu Table of Contents Your Vehicle’s Safety Features (10) (3) (4) (9) (9) Some features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment, front and rear crush zones, a collapsible steering column, and tensioners that tighten the front seat belts in a crash.
Main Menu Table of Contents Your Vehicle’s Safety Features Seat Belts Your vehicle is equipped with seat belts in all seating positions. Your seat belt system also includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.
Main Menu Table of Contents Your Vehicle’s Safety Features Airbags Driver and Passenger Safety Your vehicle has a supplemental restraint system (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision (see page 23 for more information on how your front airbags work).
Main Menu Table of Contents Your Vehicle’s Safety Features The most important things you need to know about your airbags are: Airbags do not replace seat belts. They are designed to supplement the seat belts. Airbags offer no protection in rear impacts, or minor frontal or side collisions. Airbags can pose hazards. To do their job, airbags must inflate with tremendous force.
Main Menu Table of Contents Protecting Adults and Teens See pages 32 − 49 for important guidelines on how to properly protect infants, small children, and larger children who ride in your vehicle. 1.Close and Lock the Doors After everyone has entered the vehicle, be sure the doors are closed and locked. 2.
Main Menu Table of Contents Protecting Adults and Teens If you sit too close to the steering wheel or dashboard, you can be seriously injured by an inflating front airbag, or by striking the steering wheel or dashboard. The National Highway Traffic Safety Administration and Transport Canada recommend that drivers allow at least 10 inches (25 cm) between the center of the steering wheel and the chest. In addition to adjusting the seat, you can adjust the steering wheel up and down (see page 69 ).
Main Menu Table of Contents Protecting Adults and Teens 4.Adjust the Head Restraints Adjust the seat-back to an upright position, and sit well back in the seat. Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant’s chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury.
Main Menu Table of Contents Protecting Adults and Teens This spreads the forces of a crash over the strongest bones in your upper body. 5.Fasten and Position the Seat Belts Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash. The seat belt in the center position of the back seat can be unlatched and retracted to allow the back seat to be folded up or down.
Main Menu Table of Contents Protecting Adults and Teens RELEASE BUTTONS Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause If a seat belt does not seem to work properly, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt. Using a seat The front seats have adjustable seat belt anchors.
Main Menu Table of Contents Protecting Adults and Teens In addition, an occupant who is out of position in the front seat can be seriously or fatally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag. Advice for Pregnant Women This will reduce the risk of injuries to both you and your unborn child that can be caused by a crash or an inflating front airbag. Sitting improperly or out of position can result in serious injury or death in a crash.
Main Menu Table of Contents Protecting Adults and Teens Additional Safety Precautions could be very seriously injured in a crash. Passengers should not stand up or change seats while the vehicle is moving. A passenger who is not wearing a seat belt during a crash or emergency stop can be thrown against the inside of the vehicle, against other occupants, or out of the vehicle. Two people should never use the same seat belt. If they do, they Keep your hands and arms away from the airbag covers.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The front seat belts are also equipped with automatic seat belt tensioners. The seat belt system includes an indicator on the instrument panel and a beeper to remind you to fasten your seat belt.
Main Menu Table of Contents Additional Information About Your Seat Belts DETACHABLE ANCHOR Automatic Seat Belt Tensioners If a side curtain airbag deploys during a side impact, the tensioner on that side of the vehicle will also deploy. The lap/shoulder belt in the center seating position on the rear seat is equipped with a detachable anchor that has two parts: a small latch plate and an anchor buckle. The detachable anchor should normally be latched whenever the seat-backs are in an upright position.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully, and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the belts retract easily. If a belt does not retract easily, cleaning the belt may correct the problem (see page 208 ).
Main Menu Table of Contents Additional Information About Your Airbags Your airbag system includes: Airbag System Components (1) (8) (9) (8) (2) (11) (12) (5) (3) (14) (1) Driver’s Airbag (2) Front Passenger’s Airbag (3) Control Unit (4) Front Seat Belt Tensioners (5) Side Airbags (6) Driver’s Seat Position Sensor (7) Front Passenger’s Weight Sensors (4) (8) Front Impact Sensors (10) (9) Passenger Airbag Off Indicator (6) (10) Side Impact Sensors (11) Occupant Position Detection System (OPDS) Sens
Main Menu Table of Contents Additional Information About Your Airbags Automatic front seat belt tensioners (see page 19 ). Sensors that can detect a moderate to severe front impact or side impact. Sensors that can detect whether a child is in the passenger’s side airbag path and automatically turn the airbag off (see page 27 ). A driver’s seat position sensor that monitors the distance of the seat from the front airbag.
Main Menu Table of Contents Additional Information About Your Airbags How Your Front Airbags Work Driver and Passenger Safety During a frontal crash, your seat belt restrains your lower body and torso, and the front airbag helps protect your head and chest. Although both airbags normally inflate within split second of each other, it is possible for only one airbag to deploy. If you ever have a moderate to severe frontal collision, sensors will detect the vehicle’s rapid deceleration.
Main Menu Table of Contents Additional Information About Your Airbags After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the vehicle as soon as it is safe to do so. Dual-Stage Airbags Dual-Threshold Airbags Your front airbags are dual-stage airbags.
Main Menu Table of Contents Additional Information About Your Airbags Advanced Airbags For both advanced airbags to work properly: Occupants must sit upright and wear their seat belts properly. Do not spill any liquids on or under the seats, cover the sensors, or put any cargo or metal objects under the front seats. Back-seat passengers should not put their feet under the front seats. Failure to follow these instructions could damage the sensors or prevent them from working properly.
Main Menu Table of Contents Additional Information About Your Airbags When the airbag is turned off, an indicator in the center of the dashboard will come on indicating passenger airbag ‘‘OFF’’ (see page 30 ). If the weight sensors detect there is no passenger in the front seat, the airbag will be off. However, the passenger airbag off indicator will not come on.
Main Menu Table of Contents Additional Information About Your Airbags To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats. Side Airbag Cutoff System To reduce the risk of injury from an inflating side airbag, your vehicle has an automatic cutoff system for the passenger’s side airbag.
Main Menu Table of Contents Additional Information About Your Airbags How Your Side Curtain Airbags Work If the impact is on the passenger’s side, the passenger’s side curtain airbag will inflate even if there are no occupants on that side of the vehicle. In a Rollover A rollover sensor monitors the degree and rate your vehicle may roll over and automatically deploy the side curtain airbags and activate the front seat belt tensioners (see page 19 ).
Main Menu Table of Contents Additional Information About Your Airbags If you see any of these indications, the airbags and seat belt tensioners may not work properly when you need them. When you turn the ignition switch to the ON (II) position, this indicator comes on briefly then goes off. This tells you the system is working properly. Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly.
Main Menu Table of Contents Additional Information About Your Airbags How the Passenger Airbag Off Indicator Works PASSENGER AIRBAG OFF INDICATOR If no one is riding in the front seat, the airbag will be automatically shut off. However, the indicator will not come on. If the indicator comes on with no passenger in the front, or with an adult in the seat, there may be a problem with the advanced airbag system. Have the vehicle checked by your dealer as soon as possible. U.S.
Main Menu Table of Contents Additional Information About Your Airbags If your vehicle has a moderate to severe impact. Even if your Do not attempt to deactivate your airbags. Together, airbags and Do not expose the front seat-backs to liquid. If water or another liquid seat belts provide the best protection. soaks into a seat-back, it can prevent the side airbag cutoff system from working properly. Do not tamper with airbag components or wiring for any reason.
Main Menu Table of Contents Protecting Children − General Guidelines All Children Must Be Restrained Each year, many children are injured or killed in vehicle crashes because they are either unrestrained or not properly restrained. In fact, vehicle accidents are the number one cause of the death of children aged 12 and under. Children depend on adults to protect them. However, despite their best intentions, many adults do not know how to properly protect child passengers.
Main Menu Table of Contents Protecting Children − General Guidelines Children who ride in back are less likely to be injured by striking interior vehicle parts during a collision or hard braking. Also, children cannot be injured by an inflating front airbag when they ride in the back. The Passenger’s Front Airbag Can Pose Serious Risks Front airbags have been designed to help protect adults in a moderate to severe frontal collision.
Main Menu Table of Contents Protecting Children − General Guidelines To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the dashboard (U.S. models) and on the front visors. Please read and follow the instructions on these labels. U.S.
Main Menu Table of Contents Protecting Children − General Guidelines Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page 46 ). Move the vehicle seat as far to the rear as possible (see page 78 ). Have the child sit upright and well back in the seat (see page 15 ). Make sure the seat belt is properly positioned and secured (see page 14 ).
Main Menu Table of Contents Protecting Children − General Guidelines Use the childproof door locks to prevent children from opening the rear doors. This can prevent Lock all doors, the tailgate and the hatch when your vehicle is not in use. Children who play in vehicles children from accidentally falling out (see page 73 ). can accidentally get trapped inside. Teach your children not to play in or around vehicles. Do not leave children alone in a vehicle.
Main Menu Table of Contents Protecting Infants and Small Children Protecting Infants Do not put a rear-facing child seat in a forward-facing position. If placed facing forward, an infant could be very seriously injured during a frontal collision. Child Seat Type An infant must be properly restrained in a rear-facing, reclining child seat until the child reaches the seat maker’s weight or height limit for the seat and the child is at least one year old.
Main Menu Table of Contents Protecting Infants and Small Children In any of these situations, we strongly recommend that you install the child seat directly behind the front passenger’s seat, move the seat as far forward as needed, and leave it unoccupied. Or, you may wish to get a smaller rear-facing child seat. Protecting Small Children Child Seat Placement We strongly recommend placing a forward-facing child seat in a back seat, not the front.
Main Menu Table of Contents Protecting Infants and Small Children, Selecting a Child Seat If it is necessary to put a forwardfacing child seat in the front, move the vehicle seat as far to the rear as possible, and be sure the child seat is firmly secured to the vehicle and the child is properly strapped in the seat. Selecting a Child Seat When buying a child seat, you need to choose either a conventional child seat, or one designed for use with the lower anchors and tethers for children (LATCH) system.
Main Menu Table of Contents Selecting a Child Seat, Installing a Child Seat 3.The child seat should fit the vehicle seating position (or positions) where it will be used. Before purchasing a conventional child seat, or using a previously purchased one, we recommend that you test the seat in the specific vehicle seating position (or positions) where the seat will be used.
Main Menu Table of Contents Installing a Child Seat BUTTON The lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH. LOWER ANCHORS The location of each lower anchor is indicated by a small button above the anchor point. To install a LATCH-compatible child seat: 1. Move the seat belt buckle or tongue away from the lower anchors. 2.
Main Menu Table of Contents Installing a Child Seat ANCHOR TETHER STRAP HOOK Flexible type Other LATCH-compatible seats have a flexible-type connector as shown above. 4. Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit. 42 5. Remove the head restraint (see page 80 ). Make sure the removed head restraint is secured in the cargo area. Reinstall the head restraint when the child seat is removed. 6.
Main Menu Table of Contents Installing a Child Seat In addition, the lap/shoulder belts in all seating positions except the driver’s have a locking mechanism that must be activated to secure a child seat. If you intend to install a child seat in the center seating position of the rear seat, make sure the detachable seat belt anchor is securely latched. 1.
Main Menu Table of Contents Installing a Child Seat To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Installing a Child Seat Installing a Child Seat with a Tether Using an Outer Anchor ANCHOR COVER A child seat with a tether can be installed in any seating position in the back seat, using one of the anchorage points shown above. Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available. 1.
Main Menu Table of Contents Installing a Child Seat, Protecting Larger Children Using the Center Anchor ANCHOR TETHER STRAP HOOK 1. After properly securing the child seat (see page 43 ), remove the head restraint, then route the tether strap over the seat-back. Make sure to store the removed head restraint in the cargo area and to reinstall it when the child seat is removed. 2. Follow steps 2 through 4 in the previous page.
Main Menu Table of Contents Protecting Larger Children Checking Seat Belt Fit 3. Does the shoulder belt cross between the child’s neck and arm? Using a Booster Seat Driver and Passenger Safety 4. Is the lap part of the belt as low as possible, touching the child’s thighs? 5.
Main Menu Table of Contents Protecting Larger Children Some states and Canadian provinces also require children to use a booster seat until they reach a given age or weight (e.g., 6 years or 60 lbs). Be sure to check current laws in the states or provinces where you intend to drive. A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle’s or booster’s seat-back.
Main Menu Table of Contents Protecting Larger Children If you decide that a child can safely ride up front, be sure to: Move the vehicle seat to the rearmost position. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could Have the child sit up straight, back against the seat, and feet on or near the floor.
Main Menu Table of Contents Carbon Monoxide Hazard Your vehicle’s exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the vehicle in normal driving if you maintain your vehicle properly. Have the exhaust system inspected for leaks whenever: Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide. The vehicle is raised for an oil change.
Main Menu Table of Contents Safety Labels SUN VISOR U.S. models Canadian models Driver and Passenger Safety These labels are in the locations shown. They warn you of potential hazards that could cause serious injury or death. Read these labels carefully. If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact your dealer for a replacement. DASHBOARD U.S. models only SUN VISOR U.S.
Main Menu Table of Contents Safety Labels HOOD U.S. models DOORJAMBS U.S.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach. Tailgate and Hatch Glass................ 74 Remote Transmitter ........................ 75 Seats .................................................. 78 Seat Heaters ..................................... 86 Power Windows ............................... 86 Moonroof ..........................................
Main Menu Table of Contents Control Locations POWER DOOR LOCK MASTER SWITCH (P.73) MIRROR CONTROLS (P.89) INSTRUMENT PANEL INDICATORS (P.55) GAUGES (P.61) POWER WINDOW SWITCHES (P.86) HOOD RELEASE HANDLE (P.144) HAZARD WARNING BUTTON (P.67) HATCH GLASS RELEASE BUTTON (P.74) A/T model is shown. 54 AUTOMATIC TRANSMISSION (P.161) MANUAL TRANSMISSION (P.159) AUDIO SYSTEM (P.103) CLOCK (P.137) PASSENGER AIRBAG OFF INDICATOR (P.30) SEAT HEATER SWITCH (P.86) PARKING BRAKE (P.
Main Menu Table of Contents Instrument Panel ANTI-LOCK BRAKE SYSTEM INDICATOR (P.57) SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.57) IMMOBILIZER SYSTEM INDICATOR (P.57) VSA ACTIVATION INDICATOR (P.58) CRUISE CONTROL INDICATOR (P.58) MALFUNCTION INDICATOR LAMP (P.234) LOW FUEL INDICATOR (P.59) CHARGING SYSTEM INDICATOR (P.56, 233) VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.58) * MAINTENANCE REQUIRED INDICATOR (P.60) SEAT BELT REMINDER INDICATOR (P.56) HIGH BEAM INDICATOR (P.
Main Menu Table of Contents Instrument Panel Indicators The instrument panel has many indicators that give you important information about your vehicle. Malfunction Indicator Lamp See page 234 . Low Oil Pressure Indicator The engine can be severely damaged if this indicator flashes or stays on when the engine is running. For more information, see page 233 . Charging System Indicator If this indicator comes on when the engine is running, the battery is not being charged.
Main Menu Table of Contents Instrument Panel Indicators U.S. Canada automatically shut off. For more information, see page 29 . Anti-lock Brake System (ABS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer.
Main Menu Table of Contents Instrument Panel Indicators Vehicle Stability Assist (VSA) System Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked.
Main Menu Table of Contents Instrument Panel Indicators High Beam Indicator This indicator comes on with the high beam headlights. For more information, see page 67 . On Canadian models, this indicator comes on with reduced brightness when the daytime running lights (DRL) are on (see page 67 ). Daytime Running Lights Indicator Canadian models only When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.
Main Menu Table of Contents Instrument Panel Indicators Washer Level Indicator Canadian models only This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page 198 ). Maintenance Required Indicator This indicator reminds you that it is time to take your vehicle in for scheduled maintenance. Refer to the maintenance schedule for normal and severe driving conditions on pages 187 and 188 .
Main Menu Table of Contents Gauges OUTSIDE TEMPERATURE INDICATOR TACHOMETER SPEEDOMETER FUEL GAUGE Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. Each trip meter works independently, so you can keep track of two different distances. When you turn the ignition switch to the ON (II) position, the meter you last selected is displayed.
Main Menu Table of Contents Gauges Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated. Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount.
Main Menu Table of Contents Gauges The sensor delays the display update until it reaches the correct outside temperature. This may take several minutes. If the outside temperature is incorrectly displayed, you can adjust it up ±5°F in U.S. models (±3°C in Canadian models) warmer or cooler. NOTE: The temperature must be stabilized before doing this procedure. To adjust the outside temperature display, press and hold the Select/ Reset button for 10 seconds.
Main Menu Table of Contents Controls Near the Steering Wheel HEADLIGHTS/TURN SIGNALS (P.66) VEHICLE STABILITY ASSIST (VSA) SYSTEM ON/OFF SWITCH (P.171) SHIFT LEVER (A/T) INSTRUMENT PANEL BRIGHTNESS (P.161) (P.67) WINDSHIELD WIPERS/ WASHERS (P.65) HAZARD WARNING BUTTON (P.67) PASSENGER AIRBAG OFF INDICATOR (P.30) MOONROOF SWITCH*2 (P.88) CRUISE CONTROL MASTER BUTTON (P.138) REMOTE AUDIO CONTROLS*2 (P.135) STEERING WHEEL ADJUSTMENT (P.69) HORN*1 CRUISE CONTROL PARKING BRAKE BUTTONS (P.68) (P.
Main Menu Table of Contents Windshield Wipers and Washers Windshield Wiper MIST − The wipers run at high speed until you release the lever. Rear Window Wiper and Washer OFF − The wipers are not activated. Instruments and Controls INT − The wipers operate every few seconds. LO − The wipers run at low speed. HI − The wipers run at high speed. 1. MIST 2. OFF 3. INT − Intermittent 4. LO − Low speed 5. HI − High speed 6. Windshield washers Push the right lever up or down to select a position.
Main Menu Table of Contents Windshield Wipers and Washers, Turn Signal and Headlights 3. OFF When you turn the wiper switch to the ‘‘OFF’’ position or turn off the ignition switch, the wiper will return to its parked position. Turn Signal and Headlights 4. Rotate the switch counterclockwise to turn the window wiper on and the window washer to spray. The rear wiper will not work if the hatch glass is not fully closed. If you open the hatch glass while the rear wiper is operating, the wiper will stop.
Main Menu Table of Contents Headlights, Instrument Panel Brightness, Hazard Warning Button Instrument Panel Brightness Hazard Warning Button To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
Main Menu Table of Contents Rear Window Defogger, Parking Brake Rear Window Defogger Make sure the rear window is clear and you have good visibility before starting to drive. Parking Brake The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side. PARKING BRAKE LEVER The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off.
Main Menu Table of Contents Parking Brake, Steering Wheel Adjustment Driving the vehicle with the parking brake applied can damage the rear brakes and axles. Steering Wheel Adjustment Make any steering wheel adjustment before you start driving. Instruments and Controls Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Main Menu Table of Contents Steering Wheel Adjustment, Keys and Locks Keys and Locks VALET KEY KEY NUMBER MASTER KEY WITH (Light Gray) TAG REMOTE TRANSMITTER You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks. These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged. 3.
Main Menu Table of Contents Immobilizer System The Immobilizer System protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled. The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable.
Main Menu Table of Contents Ignition Switch The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). LOCK (0) − You can insert or remove the key only in this position. To turn the key, push it in slightly. If your vehicle has an automatic transmission, the shift lever must also be in park. 72 If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
Main Menu Table of Contents Door Locks Power Door Locks MASTER DOOR LOCK SWITCH To lock the doors and the tailgate, press the master door lock switch on either front door, press the lock tab down on the driver’s door, or use the key on the outside lock on the driver’s door. Pressing up on either master door lock switch will unlock all of the doors and the tailgate. To lock any passenger’s door when getting out of the vehicle, push the lock tab down, and close the door.
Main Menu Table of Contents Tailgate and Hatch Glass HATCH GLASS RELEASE BUTTON Use the valet or master key in the tailgate to: 1. Unlock the tailgate. Pull the handle to open it. 2. Lock the tailgate. 3. Open the hatch glass. You can also open it by pressing the hatch glass release button on the driver’s door or on the remote transmitter. 74 The rear wiper will not operate with the hatch glass open. If you open the hatch glass while the rear wiper is operating, the wiper will stop (see page 65 ).
Main Menu Table of Contents Tailgate and Hatch Glass, Remote Transmitter Remote Transmitter LOCK BUTTON UNLOCK BUTTON PANIC BUTTON LED HATCH GLASS RELEASE BUTTON LOCK − Press this button once to lock all doors and the tailgate. Some exterior lights will flash once. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors and the tailgate are locked.
Main Menu Table of Contents Remote Transmitter HATCH GLASS RELEASE − Press this button for about 1 second to open the hatch glass. You cannot open the hatch glass if the key is in the ignition switch. Even if the hatch glass is open, the tailgate can be locked with the remote transmitter. PANIC − Press this button for about 2 seconds to attract attention: the horn will sound, and the exterior lights will flash for about 30 seconds.
Main Menu Table of Contents Remote Transmitter 2. Separate the transmitter by prying its middle seam with your fingernail. 4. Remove the old battery, and insert a new battery into the back of the cover with the + side facing down. 5. Install the parts in reverse order. TAB 3. Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.
Main Menu Table of Contents Seats Seat Adjustments See pages 11 − 13 for important safety information and warnings about how to properly position the seats and seatbacks. Make all seat adjustments before you start driving. FRONT SEAT To adjust the front or rear seat forward and backward, pull up on the bar under the seat cushion’s front edge. Try to move the seat to make sure it is locked in position.
Main Menu Table of Contents Seats Armrests The height of the driver’s seat is adjustable. Turn the dial on the outside of the seat cushion. The rear seat armrest is in the center of the rear seat. Pivot it down to use it. REAR SEAT To change the angle of the rear seatback, pull up on the release lever on the outside of the seat-back. When using the center seating position, adjust the left and right side of the rear seats to the same position.
Main Menu Table of Contents Seats Head Restraints See page 13 for important safety information and a warning about how to properly position the head restraints. Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint. 80 FRONT RELEASE BUTTON The head restraints adjust for height.
Main Menu Table of Contents Seats 4. Move the front seat backward until it touches the rear seat. 5. Adjust the rear seat-back to the desired position. SLIDE BAR SEAT-BACK ANGLE ADJUSTMENT LEVER You can recline the seat-backs on the front seats so they are level with the rear seat cushions, making a large cushioned area. To do this: 1. Adjust the rear seats as far back as they will go. 2. Remove the head restraints from the front seats (see page 80 ).
Main Menu Table of Contents Seats Folding the Rear Seats Down The rear seat-back can be folded down to give more cargo room. Each side folds down separately, so you can still carry a passenger in the rear seat. You can also fold up each of the rear seats separately to create further cargo space (see page 83 ). LATCH PLATE When you are folding the right half of the rear seat, use the key to release the center seat belt from the detachable anchor (see page 85 ).
Main Menu Table of Contents Seats Reverse this procedure to return the seat-back to the upright position. Make sure the seat is secured and the seat belt in front of the seat-back before driving. Folding the Rear Seat Up LOCK RELEASE STRAP To fold up the rear seat: 1. Pull up the bar under the seat cushion and slide the rear seat backward. The rear seat will not fold up if it is not back as far as it will go. 2. Follow steps 1 through 4 on page 82 for folding down the seatback. 3.
Main Menu Table of Contents Seats HOOK Reverse this procedure to return the seat to the upright position. Make sure the seat is securely latched before driving. When you are not using the fastening strap, roll up the strap and store it properly into the slit on the seat-back. FASTENING STRAP Make sure all rear shoulder belts are positioned in front of the rear seatbacks. HOOK 5. Pull out the fastening strap from the slit on the seat-back.
Main Menu Table of Contents Seats SMALL BUCKLE Using a seat belt with the detachable anchor unlatched increases the chance of serious injury or death in a crash. Before using the seat belt, make sure the detachable anchor is correctly latched. SMALL LATCH PLATE Instruments and Controls Detachable Anchor The seat belt in the rear center seat is equipped with a detachable anchor. This allows the center seat belt to be unlatched when the right side of the rear seat is folded.
Main Menu Table of Contents Seat Heaters, Power Windows Seat Heaters DRIVER’S SEAT HEATER SWITCH PASSENGER’S SEAT HEATER SWITCH If equipped Both front seats are equipped with seat heaters in the seat bottoms only. Because of sensors for the side airbag system, there are no heaters in the seat-back in either the driver or passenger seats. The ignition switch must be in the ON (II) position to use them. Push the heater switch to turn the power on or off.
Main Menu Table of Contents Power Windows Closing a power window on someone’s hands or fingers can cause serious injury. AUTO − To open or close the driver’s window, push or pull the window switch firmly down or up to the second detent, and release it. The window will automatically go up or down all the way. To stop the window, pull or push the window switch briefly. AUTO REVERSE − If the driver’s window senses any obstacle while it is closing automatically, it will reverse direction, and then stop.
Main Menu Table of Contents Moonroof, Mirrors Moonroof hold the bottom of the switch ( ). Opening or closing the moonroof on someone’s hands or fingers can cause serious injury. Mirrors TAB Make sure all hands and fingers are clear of the moonroof before opening or closing it. If equipped Turn the ignition switch to the ON (II) position, and use the switch under the left dashboard vent to operate the moonroof. To tilt up the back of the moonroof, press and hold the center button ( ).
Main Menu Table of Contents Mirrors Adjusting the Power Mirrors SELECTOR SWITCH 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down. Power Mirror Heaters ADJUSTMENT SWITCH 1. Turn the ignition switch to the ON (II) position. 2. Move the selector switch to L (driver’s side) or R (passenger’s side). Instruments and Controls 4. When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.
Main Menu Table of Contents Interior Convenience Items COAT HOOK ACCESSORY POWER SOCKET DRIVER’S POCKET SUN VISOR SUNGLASSES HOLDER VANITY MIRROR DASHBOARD POCKET PASSENGER’S TRAY BUILT-IN TABLE *1 : M/T model only *2 : A/T model only 90 BEVERAGE HOLDERS in REAR SEAT ARMREST ACCESSORY CENTER TABLE with POWER SOCKET BEVERAGE HOLDERS BEVERAGE CENTER*2 GLOVE BOX HOLDER*2/ POCKET COIN TRAY*1
Main Menu Table of Contents Interior Convenience Items Built-in Table HANDLE The cargo area floor can be taken out and used as a table. To remove the table, pull up the carpet. Lift and pull on the handle to slide the table out. Only on models with an automatic transmission To use the front beverage holder, pull on the handle. CONTINUED 91 Instruments and Controls Beverage Holders Be careful when you are using the beverage holders. Spilled liquid that is very hot can scald you or your passengers.
Main Menu Table of Contents Interior Convenience Items Using the Built-in Table Be sure to lock the legs of the table. Do not sit or stand on the table. Do not put a weight of over 44 lbs (20 kg) on the table. Hot items such as pots, pans, or kettles should not be placed directly on the tabletop. Unfold the legs. Lock them in place by pushing on the middle of the locking arms. Make sure all four are locked. 92 To fold the legs, pull on the middle of each locking arm.
Main Menu Table of Contents Interior Convenience Items Glove Box Coin Tray Instruments and Controls An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. Lock Open the glove box by pulling the bottom of the handle. Close it with a firm push. Lock or unlock the glove box with the master key. The glove box light comes on only when the parking lights are on.
Main Menu Table of Contents Interior Convenience Items Sunglasses Holder Center Table Push SUNGLASSES HOLDER To open the sunglasses holder, push on the front edge. Make sure the holder is closed while you are driving. Some larger styles of sunglasses may not fit in the holder. 94 To use the center table, pull up the outside edge of the table until it latches. To store it, pull the lever and lower the table.
Main Menu Table of Contents Interior Convenience Items, Interior Lights Accessory Power Sockets These sockets are intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps). Center Pocket Ceiling Light None of the sockets will power an automotive type cigarette lighter element. When more than one socket is being used, the combined power rating of the accessories should be 120 watts or less (10 amps).
Main Menu Table of Contents Interior Lights After all doors are closed tightly, the light fades out in about 30 seconds. Spotlights Cargo Area Light The ceiling light (with the switch in the center position) comes on when you remove the key from the ignition switch. If you do not open a door, the light fades out in about 30 seconds. ON OFF If you leave any door or the tailgate open with the key not in the ignition switch, the ceiling light will go off after 3 minutes.
Main Menu Features The heating and air conditioning system in your vehicle provides a comfortable driving environment in all weather conditions. Your vehicle has an anti-theft audio system that requires a code number to enable it. 97 Features The standard audio system has many features. This section describes those features and how to use them. Vents, Heating, and A/C ................ 98 Audio System ................................. 103 Playing the Radio .................... 105,116 Playing a Disc ..
Main Menu Table of Contents Vents, Heating, and A/C FAN CONTROL DIAL TEMPERATURE CONTROL DIAL MODE CONTROL DIAL REAR WINDOW DEFOGGER/ HEATED MIRRORS BUTTON (If equipped) RECIRCULATION BUTTON 98 AIR CONDITIONING (A/C) BUTTON REAR WINDOW DEFOGGER BUTTON
Main Menu Table of Contents Vents, Heating, and A/C Air Flow Buttons Fan Control Dial Turn this dial to increase or decrease the fan speed and airflow. Air Conditioning (A/C) Button This button turns the air conditioning on and off. The indicator in the button is on when the A/C is on. Recirculation Button When the recirculation indicator is on, air from the vehicle’s interior is sent throughout the system again.
Main Menu Table of Contents Vents, Heating, and A/C Airflow is divided between the floor vents and the defroster vents at the base of the windshield. Air flows from the defroster vents at the base of the windshield. When you select or , the system automatically switches to fresh air mode and turns on the A/C. In this case, you cannot turn the A/C off. Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the tailgate.
Main Menu Table of Contents Vents, Heating, and A/C To cool the interior with MAX A/C: If the interior is very warm, you can cool it down more rapidly by partially opening the windows, turning on the A/C, and setting the fan to maximum speed in fresh air mode. 1. Turn the fan on. 2. Turn on the air conditioning. and fresh air mode. 3. Select 4. Adjust the temperature to your preference. This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).
Main Menu Table of Contents Vents, Heating, and A/C When you select or , the system automatically switches to fresh air mode and turns on the A/C. This helps to dehumidify the air and to defog the windshield. In either mode, you cannot turn off the A/C. When you switch to another mode, the A/C returns to its original setting, either on or off, as displayed by the A/C indicator. To Remove Exterior Frost or Ice From the Windows . The system 1.
Main Menu Table of Contents Audio System Some models may have one of the audio systems described in this section. Read the appropriate pages in this section for operation of the audio systems installed in your vehicle. U.S. LX and Canadian SE model Features page 105 to 115 for U.S. LX model, Canadian SE model page 116 to 131 for U.S. EX, SE models, Canadian EX, EX-L models If your vehicle has a different audio system refer to its manual for operating instructions.
Main Menu Table of Contents Audio System Canadian EX and EX-L models 104 U.S.
Main Menu Table of Contents Playing the Radio U.S.
Main Menu Table of Contents Playing the Radio To Play the Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the PWR/VOL knob or the AM or FM button. Adjust the volume by turning the PWR/VOL knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM or FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Table of Contents Playing the Radio Preset − Each preset button can store one frequency on AM and two frequencies on FM. 2. Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station. 3. Pick a preset button and hold it until you hear a beep. 4. Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM. The preset frequencies will be lost if your vehicle’s battery goes dead, is disconnected, or the radio fuse is removed.
Main Menu Table of Contents Playing the Radio Adjusting the Sound BAL − Adjust the balance or sideto-side strength of the sound. FAD − Adjust the fader or the front-to-back strength of the sound. TRE − Adjust the treble in the sound. BAS − Adjust the bass in the sound. 108 BAS/FAD: Press the knob to pop it out. Turn it to adjust the Bass level. Pull it out slightly farther to adjust the Fade, or front-to-back strength. Push the knob back in when you are done adjusting the sound.
Main Menu Table of Contents Playing a Disc U.S.
Main Menu Table of Contents Playing a Disc To Play a CD To load or play CDs, the ignition switch must be in the ACCESSORY (I) or the ON(II) position. You operate the CD player with the same controls used for the radio. To select the CD player, press the CD button. The number of the track playing is shown in the display. The system will continuously play a CD until you change modes. Insert a CD into the CD slot. The drive will pull the CD in the rest of the way to play it.
Main Menu Table of Contents Playing a Disc RANDOM − This feature plays the tracks in random order. To activate random play, press and release the RDM button. You will see RDM in the display. Press it again to return to normal play. To Stop Playing a CD Press the eject button ( ) to remove the CD. If you eject the CD, but do not remove it from the slot, the system will automatically reload the CD after 10 seconds and put it in pause mode. To begin playing, press the CD button.
Main Menu Table of Contents Disc Player/Changer Error Messages If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer. CD Player Error Message Cause Mechanical Error High temperature Focus Error CD Changer Error Message Cause High temperature No CD in magazine Focus Error Mechanical Error 112 Solution Press the CD eject button and pull out the CD.
Main Menu Table of Contents Playing a Tape U.S.
Main Menu Table of Contents Playing a Tape To Play a Tape The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Make sure the open side of the tape is facing right, then insert the tape most of the way into the slot. The system will pull the tape in the rest of the way and begin to play it. Dolby* noise reduction turns on when you insert a tape. The indicator will light in the display. If the tape was not recorded in Dolby, turn it off by pressing the button.
Main Menu Table of Contents Playing a Tape REPEAT − Press the RPT button to continuously play a song or passage. You will see REPEAT displayed. The track will repeat until you press the RPT button again. If you do not clean the tape player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit. Your dealer has a cleaning kit available. Use 100-minute or shorter tapes. Tapes longer than that may break or jam the drive.
Main Menu Table of Contents Playing the Radio Canadian EX and EX-L models POWER/VOLUME KNOB FM/AM BUTTON U.S.
Main Menu Table of Contents Playing the Radio To Play the Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on by pushing the PWR/VOL knob or the FM/AM button. Adjust the volume by turning the PWR/VOL knob. Optional for U.S. EX and SE models. XM satellite radio information is available on page 120 . TUNE − Use the TUNE knob to tune the radio to a desired frequency. Turn the knob right to tune to a higher frequency, or left to tune to a lower frequency.
Main Menu Table of Contents Playing the Radio Preset − Each preset button can store one frequency on AM and two frequencies on FM. 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset button. 2. Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station. 3. Pick a preset button and hold it until you hear a beep. 4. Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.
Main Menu Table of Contents Playing the Radio Adjusting the Sound BAL − Adjust the balance or sideto-side strength of the sound. FAD − Adjust the fader or the front-to-back strength of the sound. BAS − Adjust the bass in the sound. Each mode is shown in the display as it changes. Turn the SOUND knob to adjust the setting to your liking. When the level reaches the center, you will see a ‘‘C’’ in the display. The system will return to the audio display about 5 seconds after you stop adjusting a mode.
Main Menu Table of Contents Playing the XM Satellite Radio (optional) Optional on U.S.
Main Menu Table of Contents Playing the XM Satellite Radio (optional) Satellite Digital Radio Optional on U.S. EX and SE models Your vehicle is capable of receiving XM satellite radio anywhere in the United States except Hawaii and Alaska. To Play XM Satellite Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on: Push any of the following: PWR/ VOL knob or the CD/XM button. Turn the PWR/VOL knob to adjust the volume.
Main Menu Table of Contents Playing the XM Satellite Radio (optional) Signal may be blocked by mountains or large obstacles to the south. Signal is weaker in these areas. Satellite Radio Signals Satellite radio receives signals from two satellites to produce clear, highquality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, satellite radio also allows you to view channel and category selections in the audio display.
Main Menu Table of Contents Playing the XM Satellite Radio (optional) Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions: There may also be other geographic situations that could affect satellite radio reception. Receiving Satellite Radio Service If your XM Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM satellite radio.
Main Menu Table of Contents Playing a Disc Canadian EX and EX-L models LOAD BUTTON RANDOM BUTTON U.S.
Main Menu Table of Contents Playing a Disc To Play a CD To load or play CDs, the ignition switch must be in the ACCESSORY (I) or the ON(II) position. You can also play 3-inch (8-cm) discs without using an adapter ring. Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit. To play the radio when a CD is playing, press the AM/FM button. Press the CD button again to switch back to the CD player.
Main Menu Table of Contents Playing a Disc 4. When the CD load indicator turns green and ‘‘LOAD’’ appears in the screen again, insert the next CD in the slot. Do not try to insert a CD until ‘‘LOAD’’ appears. You could damage the audio unit. 5. Repeat this until all six positions are loaded. If you are not loading all six positions, the system begins playing the last CD loaded. You can also load a CD into an empty position while a CD is playing by pressing the appropriate preset button.
Main Menu Table of Contents Playing a Disc To Stop Playing a CD Press the FM/AM or CD button to switch to the radio or satellite radio while a CD is playing. To play the CD, press the CD button again. If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.
Main Menu Table of Contents Disc Changer Error Messages If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer. CD Changer Error Message Cause FOCUS Error Mechanical Error No CD in the CD changer 128 Solution Press the CD eject button and pull out the CDs. Check for an error message, and insert the CDs again.
Main Menu Table of Contents Playing a Tape Canadian EX and EX-L models POWER/ TAPE DIRECTION INDICATOR VOLUME KNOB TAPE SLOT DOLBY INDICATOR U.S.
Main Menu Table of Contents Playing a Tape To Play a Tape The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Make sure the open side of the tape is facing right, then insert the tape most of the way into the slot. The system will pull the tape in the rest of the way and begin to play it. Dolby* noise reduction turns on when you insert a tape. The indicator will light in the display. If the tape was not recorded in Dolby, turn it off by pressing the button.
Main Menu Table of Contents Playing a Tape REPEAT − Press the RPT button to continuously play a song or passage. You will see RPT displayed. The track will repeat until you press the RPT button again. If you do not clean the tape player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit. Your dealer has a cleaning kit available. Use 100-minute or shorter tapes. Tapes longer than that may break or jam the drive.
Main Menu Table of Contents Radio Reception Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz Radio stations on the AM band are assigned frequencies at least 10 kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 megahertz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
Main Menu Table of Contents Radio Reception As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Features Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter.
Main Menu Table of Contents Protecting Your Discs Protecting Your CDs Protecting CDs General Information When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. When using CD-R/CD-RW discs, use only high quality CDs labeled for audio use. When recording a CD-R/CD-RW, the recording must be closed for it to be used by the system. Play only standard round CDs.
Main Menu Table of Contents Remote Audio Controls CH BUTTON MODE BUTTON If equipped Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel. If you are playing a CD, the system skips to the beginning of the next track each time you push the CH button. You will see the disc and track number in the display. The MODE button changes the mode.
Main Menu Table of Contents Radio Theft Protection Your vehicle’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code in the preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible. You should have received a card that lists your audio system’s code and serial numbers.
Main Menu Table of Contents Setting the Clock If your vehicle’s battery is disconnected or goes dead, you will need to set the clock. U.S.: LX model Canada: SE model RESET BUTTON CLOCK When you are finished, press the CLOCK button again. You can quickly set the time to the nearest hour. If the displayed time is before the half hour, press the CLOCK button until you hear a beep, then press the R (preset 6) button to set the clock back to the previous hour.
Main Menu Table of Contents Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather. Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather.
Main Menu Table of Contents Cruise Control When climbing a steep hill, the automatic transmission may downshift to hold the set speed. Changing the Set Speed You can increase the set cruising speed in any of these ways: Press and hold the RES/ACCEL button. When you reach the desired cruising speed, release the button. Push on the accelerator pedal until you reach the desired cruising speed, then press the SET/ DECEL button. To increase the speed in very small amounts, tap the RES/ ACCEL button.
Main Menu Table of Contents Cruise Control Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed. Resting your foot on the brake or clutch pedal causes the cruise control to cancel. Canceling Cruise Control You can cancel cruise control in any of these ways: Tap the brake or clutch pedal. Push the CANCEL button on the steering wheel.
Main Menu Before Driving Break-in Period .............................. 142 Fuel Recommendation .................. 142 Service Station Procedures .......... 143 Refueling..................................... 143 Opening and Closing the Hood ................................. 144 Oil Check .................................... 145 Engine Coolant Check .............. 146 Fuel Economy ................................ 147 Accessories and Modifications .... 148 Carrying Cargo ..............................
Main Menu Table of Contents Break-in Period, Fuel Recommendation Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Do not change the oil until the scheduled maintenance time. Avoid hard braking for the first 200 miles (300 km). Do not tow a trailer.
Main Menu Table of Contents Service Station Procedures Refueling Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. ATTACHMENT 1. Park with the driver’s side closest to the service station pump. 4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘top off’’ the tank. Leave some room for the fuel to expand with temperature changes.
Main Menu Table of Contents Service Station Procedures 5. Screw the fuel fill cap back on until it clicks at least once. If you do not properly tighten the cap, the malfunction indicator lamp may come on (see page 234 ). Opening and Closing the Hood HOOD RELEASE HANDLE LATCH 6. Push the fuel fill door closed until it latches. 1. Park the vehicle, and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly. 2.
Main Menu Table of Contents Service Station Procedures Oil Check SUPPORT ROD DIPSTICK UPPER MARK CLIP 3. Pull the support rod out of its clip, and insert the end into the designated hole in the hood. To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check MAX RESERVE TANK MIN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If it is below the MIN line, see Adding Engine Coolant on page 196 for information on adding the proper coolant. 146 Refer to Owner’s Maintenance Checks on page 186 for information about checking other items on your vehicle.
Main Menu Table of Contents Fuel Economy Improving Fuel Economy Always maintain your vehicle according to the maintenance schedule. See Owner’s Maintenance Checks (see page 186 ). For example, an underinflated tire The build-up of snow or mud on your vehicle’s underside adds weight and rolling resistance. Frequent cleaning helps your fuel mileage and reduces the chance of corrosion. Combine several short trips into one. The air conditioning puts an extra load on the engine which makes it use more fuel.
Main Menu Table of Contents Accessories and Modifications Modifying your vehicle, or installing some non-Honda accessories, can make it unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Honda accessories that allow you to personalize your vehicle. These accessories have been designed and approved for your vehicle, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifying Your Vehicle Removing parts from your vehicle, or replacing components, with non-Honda components could seriously affect your vehicle’s handling, stability, and reliability. Some examples are Modifying your steering wheel or any other part of your vehicle’s safety features can make the systems ineffective.
Main Menu Table of Contents Carrying Cargo TAILGATE POCKETS DOOR POCKETS DASHBOARD POCKET Your vehicle has several convenient storage areas: Tailgate pockets Glove box Dashboard pocket Door pockets Seat-back pockets Center pocket Cargo area, including the rear seats when folded up or down. However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, and make it unsafe.
Main Menu Table of Contents Carrying Cargo Load Limits The maximum load for your vehicle is 850 lbs (385 kg) for U.S.A, 395 kg for Canada. This figure includes the total weight of all occupants, cargo, and accessories, and the tongue load if you are towing a trailer. Follow all load limits and other loading guidelines in this manual. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Passenger Compartment Store or secure all items that could be thrown around and hurt someone during a crash. Be sure items placed on the floor behind the front seats cannot roll under the seats and interfere with the driver’s ability to operate the pedals, the proper operation of the seats, or the advanced front airbags. Keep the glove box closed while driving.
Main Menu Table of Contents Carrying Cargo If you use an accessory roof rack, the roof rack weight limit may be lower. Refer to the information that came with your roof rack. Optional Separation Net The separation net can be used to hold back soft, lightweight items stored in the cargo area. Heavy items should be properly secured on the floor of the cargo area. The net may not prevent heavy items from being thrown forward in a crash or a sudden stop.
Main Menu 154
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the manual and automatic transmissions. It also includes important information on parking your vehicle, the braking system, the vehicle stability assist (VSA) system, and facts you need if you are planning to tow a trailer or drive off-highway. 155 Driving Driving Guidelines ......................... 156 Preparing to Drive ..................... 157 Starting the Engine........................
Main Menu Table of Contents Driving Guidelines Your vehicle has higher ground clearance that allows you to travel over bumps, obstacles, and rough terrain. It also provides good visibility so you can anticipate problems earlier. Because your vehicle rides higher off the ground, it has a high center of gravity that can cause it to roll over if you make abrupt turns. Utility vehicles have a significantly higher roll over rate than other types of vehicles.
Main Menu Table of Contents Driving Guidelines Preparing to Drive You should do these checks and adjustments before you drive your vehicle: 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood is fully closed. 4. Check that any items you may be carrying are stored properly or fastened down securely. 6. Check the adjustment of the inside and outside mirrors (see page 88 ). 7.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu Table of Contents Manual Transmission Come to a full stop before you shift into reverse. You can damage the transmission by trying to shift into reverse with the vehicle moving. Push down the clutch pedal, and pause for a few seconds before shifting into reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’ Use extra care when driving on slippery surfaces.
Main Menu Table of Contents Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control.
Main Menu Table of Contents Automatic Transmission Shift Lever Position Indicators The ‘‘D’’ indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. These indicators on the instrument panel show which position the shift lever is in. SHIFT LEVER To shift from any position, press firmly on the brake pedal and pull the lever toward you.
Main Menu Table of Contents Automatic Transmission Park (P) − This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Pull the shift lever towards you, then move it out of Park. To shift from: P to R R to P N to R D to 2 2 to 1 1 to 2 2 to D D to N N to D R to N 162 Do this: Press the brake pedal and pull the shift lever towards you.
Main Menu Table of Contents Automatic Transmission Neutral (N) − Use Neutral if you need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to the Park position if you need to leave your vehicle for any reason. Press on the brake pedal when you are moving the shift lever from Neutral to another gear. Drive (D) − Use this position for your normal driving. The transmission automatically selects a suitable gear (1 through 5) for your speed and acceleration.
Main Menu Table of Contents Automatic Transmission Shifting out from the D position will cancel the D3 mode, and the D3 indicator will go out. Selecting the D3 position again will resume the D3 mode and the indicator comes on. Turning the ignition switch to the LOCK (0) position turns this mode off. When you restart the engine, select the D position and press the D3 mode switch again to use this mode.
Main Menu Table of Contents Automatic Transmission Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal does not work. This procedure is also used to release the reverse lockout. COVER 1. Set the parking brake. 3. Put a cloth on the edge of the shift lock release slot cover. Using a small flat-tipped screwdriver or metal fingernail file, carefully pry on the edge of the cover to remove it. SHIFT LOCK RELEASE SLOT 4.
Main Menu Table of Contents Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline. Parking Tips Make sure the moonroof (if equipped) and the windows are closed. Turn off the lights. If your vehicle has an automatic transmission, set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission.
Main Menu Table of Contents Braking System Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The anti-lock brake system (ABS) helps you retain steering control when braking very hard. Constant application of the brakes when going down a long hill builds up heat and reduces their effectiveness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower gear.
Main Menu Table of Contents Anti-lock Brakes (ABS) The anti-lock brake system (ABS) helps prevent the brakes from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it. The ABS also balances the front-torear braking distribution according to vehicle loading. You should never pump the brake pedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as ‘‘stomp and steer.
Main Menu Table of Contents Anti-lock Brakes (ABS) If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the front-to-rear braking distribution system may also be shut down. The VSA indicator will come on along with the ABS indicator. ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe speed for the road and weather conditions.
Main Menu Table of Contents Vehicle Stability Assist (VSA) System The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.
Main Menu Table of Contents Vehicle Stability Assist (VSA) System If this indicator comes on while driving, pull to the side of the road when it is safe, and turn off the engine. Reset the system by restarting the engine. If the VSA system indicator stays on, or comes back on while driving, have the VSA system inspected by your dealer. Without VSA, your vehicle will have normal braking and cornering ability, but it will not have VSA traction and stability enhancement.
Main Menu Table of Contents Towing a Trailer Your vehicle has been designed to primarily carry passengers and their cargo. You can also use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Load Limits Be sure to read the Off-Highway Driving Guidelines section on page 179 if you plan to tow off paved surfaces.
Main Menu Table of Contents Towing a Trailer To achieve a proper tongue load, start by loading 60 percent of the load toward the front of the trailer and 40 percent toward the rear, then re-adjust the load as needed. Gross Axle Weight Ratings (GAWR) − The maximum allowable weight of the vehicle, all occupants, all accessories, all cargo, and the tongue load must not exceed 2,200 lbs (1,000 kg) on the front axle, and 2,290 lbs (1,040 kg) on the rear axle.
Main Menu Table of Contents Towing a Trailer Trailer Brakes Trailer Lights Honda requires that any trailer with a total weight of 1,000 lbs (455 kg) or more be equipped with its own electric or surge-type brakes. Trailer lights and equipment must comply with federal, state, province, and local regulations. Check with your local trailer sales or rental agencies for the requirements in your area where you plan to tow, and use only equipment designed for your vehicle.
Main Menu Table of Contents Towing a Trailer Additional Towing Equipment Many states and Canadian provinces require special outside mirrors when towing a trailer. Even if they don’t, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot. The vehicle has been properly serviced, and the tires, brakes, suspension, cooling system, and lights are in good operating condition. (If you tow frequently, follow the severe conditions maintenance schedule.
Main Menu Table of Contents Towing a Trailer Towing Speeds and Gears Drive slower than normal in all driving situations, and obey posted speed limits for vehicles with trailers. If you have an automatic transmission, use the D3 mode when towing a trailer on level roads or in hilly terrain (see page 163 ). Making Turns and Braking Make turns more slowly and wider than normal. The trailer tracks a smaller arc than your vehicle, and it can hit or run over something the vehicle misses.
Main Menu Table of Contents Towing Your Vehicle Behind a Motorhome Your vehicle can be towed behind a motorhome at legal highway speeds up to 65 mph (100 km/h). Do not exceed 65 mph (100 km/h). Otherwise, severe transmission damage will occur. To avoid damage to the 4WD system, your vehicle must be towed with all four wheels on the ground (flat towing). Perform the following procedure every day immediately before you begin towing. Otherwise severe automatic transmission damage will occur.
Main Menu Table of Contents Towing Your Vehicle Behind a Motorhome Automatic Transmission Extended Towing The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (I) position, and make sure the steering wheel turns f reely bef ore you begin towing. Extended Towing If you tow more than 8 hours in one day, you should repeat the above procedure at least every 8 hours (when you stop for fuel, etc.
Main Menu Table of Contents Off-Highway Driving Guidelines General Information Your vehicle has been designed primarily for use on pavement. But its higher ground clearance allows you to occasionally travel on unpaved roads, such as campgrounds, picnic sites, and similar locations. It is not designed for trail-blazing, mountain climbing, or other challenging offroad activities. Follow all instructions and guidelines in this owner’s manual.
Main Menu Table of Contents Off-Highway Driving Guidelines Check Out Your Vehicle Before you leave the pavement, be sure to do all scheduled maintenance and service, and inspect your vehicle for any problems. Pay special attention to the condition of the tires, and check the tire pressures. After you return to the pavement, carefully inspect your vehicle to make sure there is no damage that could make driving it unsafe. Recheck the condition of the tires and the tire pressures.
Main Menu Table of Contents Off-Highway Driving Guidelines Crossing a Stream Avoid driving through deep water. If you encounter water in your route (a small stream or large puddle, for example), evaluate it carefully before going ahead. Make sure it is shallow, flowing slowly, and has firm ground underneath. If you are not sure of the depth or the ground, turn around and find another route. You should never use a jack to try getting unstuck. A jack only works on firm, level ground.
Main Menu 182
Main Menu Maintenance This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions. This section also includes maintenance schedules for normal driving and severe driving conditions, a maintenance record, and instructions for simple maintenance tasks you may want to take care of yourself.
Main Menu Table of Contents Maintenance Safety All service items not detailed in this section should be performed by a certified technician or other qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required. Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off. To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.
Main Menu Table of Contents Maintenance Schedule The maintenance schedule assumes you will use your vehicle as normal transportation for passengers and their possessions. You should also follow these recommendations: Avoid exceeding your vehicle’s load limit. This puts excess stress on the engine, brakes, and many other vehicle parts. The load limit is shown on the tire information label on the driver’s doorjamb. Drive your vehicle regularly over a distance of several miles (kilometers).
Main Menu Table of Contents Maintenance Schedule Servicing Your Vehicle Your authorized dealer knows your vehicle best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or skilled person to keep your warranties in effect. Keep all the receipts as proof of completion, and have the person who does the work fill out the maintenance record.
Main Menu Table of Contents 140 224 150 240 Every 20,000 miles (32,000 km) or every 1 year, whichever comes first Every 30,000 miles (48,000 km) or every 2 years, whichever comes first Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy Every 120,000 miles (192,000 km) or every 6 years, whichever comes first Every 90,000 miles (144,000 km) or every 5 years, whichever comes first Every 160,000 miles (256,000 km) At 120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96
Maintenance Schedule for Severe Conditions Main Menu Table of Contents Check engine oil and coolant Check tires Replace engine oil Rotate tires (follow pattern on page 214 ) Replace engine oil filter Check front and rear brakes Lubricate all hinges, locks and latches Inspect the following items: Tie-rod ends, steering gearbox, and boots Suspension components Driveshaft boots Check parking brake adjustment Inspect the following items: Brake hoses and lines (including ABS) All fluid levels and condition of
Main Menu Table of Contents Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 187 ) or severe conditions (page 188 ). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Maintenance Record (for Normal and Severe Schedules) 55,000 mi 88,000 km Signature or dealer stamp mi/km 80,000 mi 128,000 km mi/km 85,000 mi 136,000 km mi/km 90,000 mi 144,000 km mi/km 95,000 mi 152,000 km mi/km Date 190 mi/km Date Date 75,000 mi 120,000 km mi/km Date Date 70,000 mi 112,000 km mi/km Date Date 65,000 mi 104,000 km mi/km Date Date 60,000 mi 96,000 km Signature or dealer stamp 100,000 mi 160,000 km mi/km Date
Main Menu Table of Contents Maintenance Record (for Normal and Severe Schedules) 105,000 mi 168,000 km Signature or dealer stamp mi/km 130,000 mi 208,000 km mi/km 135,000 mi 216,000 km mi/km 140,000 mi 224,000 km mi/km 145,000 mi 232,000 km Date Maintenance mi/km mi/km Date Date 125,000 mi 200,000 km mi/km Date Date 120,000 mi 192,000 km mi/km Date Date 115,000 mi 184,000 km mi/km Date Date 110,000 mi 176,000 km Signature or dealer stamp 150,000 mi 240,000 km mi/km Date 191
Main Menu Table of Contents Fluid Locations ENGINE OIL FILL CAP BRAKE FLUID (Black cap) ENGINE OIL DIPSTICK (Orange handle) WASHER FLUID (Blue cap) POWER STEERING FLUID (Red cap) CLUTCH FLUID (Manual Transmission only) (Gray cap) ENGINE COOLANT RESERVOIR RADIATOR CAP 192 AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)
Main Menu Table of Contents Adding Engine Oil Adding Engine Oil ENGINE OIL FILL CAP damage the engine. Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20 detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. API CERTIFICATION SEAL The oil viscosity or weight is provided on the container’s label.
Main Menu Table of Contents Adding Engine Oil, Changing the Oil and Filter Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil, it displays the API Certification Seal and it is the proper weight. You must follow the oil and filter change intervals given in the maintenance schedule. Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.
Main Menu Table of Contents Changing the Oil and Filter OIL FILTER 6. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 33 lbf·ft (44 N·m , 4.5 kgf·m) 7. Refill the engine with the recommended oil. Engine oil change capacity (including filter): 4.4 US qt (4.2 ) 4. Check the oil filter to make sure its gasket did not stick to the engine block. A stuck gasket could cause an oil leak. 5. Install a new oil filter according to the instructions that come with it.
Main Menu Table of Contents Engine Coolant Adding Engine Coolant RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. 196 Always use Honda Long-life Antifreeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.
Main Menu Table of Contents Engine Coolant RADIATOR CAP RESERVE TANK 5. Pour coolant into the reserve tank. Fill it halfway between the MAX and MIN marks. Put the cap back on the reserve tank. Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components. 2. Remove the radiator cap by pushing it down and turning it counterclockwise. Maintenance 1.
Main Menu Table of Contents Windshield Washers Check the fluid level in the windshield washer reservoir at least monthly during normal use. on a clean cloth. This will help to condition the blade edges. LOWER LEVEL MARK Fill up to here To check the windshield washer fluid level, open the driver’s door, then look at the side of the reservoir tank located between the door and the front dashboard. On Canadian models: The low washer level indicator comes on when the level is low (see page 60 ).
Main Menu Table of Contents Transmission Fluid Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment. Automatic Transmission Fluid DIPSTICK UPPER MARK LOWER MARK 1. Park the vehicle on level ground. Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth. 3. Insert the dipstick all the way into the transmission securely as shown in the illustration. 4.
Main Menu Table of Contents Transmission Fluid 6. Insert the dipstick all the way back into the transmission securely as shown in the illustration. Manual Transmission Fluid WASHER FILLER BOLT The transmission should be drained and refilled with new fluid according to the time and distance recommendations in the maintenance schedule. If you are not sure how to add fluid, contact your dealer.
Main Menu Table of Contents Rear Differential Fluid, Brake and Clutch Fluid Rear Differential Fluid 4WD model only The rear differential should be drained and refilled with new fluid according to the time and distance recommendations in the maintenance schedule. Have your dealer replace the rear differential fluid. Use Honda Dual Pump Fluid only. Do not use automatic transmission fluid (ATF). Brake and Clutch Fluid Check the brake fluid level in the reservoirs monthly.
Main Menu Table of Contents Brake and Clutch Fluid, Power Steering Fluid Clutch Fluid Power Steering Fluid Manual Transmission only UPPER LEVEL MAX Always use Honda Power Steering Fluid. You may use another power steering fluid as an emergency replacement, but have the power steering system flushed and refilled with Honda PSF as soon as possible. A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently, and have the system inspected as soon as possible.
Main Menu Table of Contents Lights Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the cargo area or pull a trailer, readjustment may be required. Adjustments should be done by your dealer or other qualified mechanic. Replacing a Headlight Bulb Your vehicle has halogen headlight bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects.
Main Menu Table of Contents Lights 5. Install the rubber seal over the back of the headlight assembly. Make sure it is right side up; it is marked ‘‘→.’’ 6. Push the electrical connector onto the new bulb. Make sure it is connected securely. Turn on the headlights to test the new bulb. High Beam Headlight 4. Install the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place, and clip the end into the slot.
Main Menu Table of Contents Lights Replacing a Parking Light/Front Side Marker Bulb and a Turn Signal Light Bulb 1. Open the hood. 2. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise. COVER PARKING LIGHT/FRONT SIDE MARKER BULB 4. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 1. Open the tailgate. Place a cloth on the edge of the cover.
Main Menu Table of Contents Lights BULBS 6. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 7. Reinstall the socket into the light assembly by turning it clockwise until it locks. SCREW 8. Turn on the lights to make sure the new bulb is working. 2. Use a Phillips-head screwdriver to remove the taillight assembly mounting screw under each cover. 3. Pull the taillight assembly out of the rear pillar. 206 4.
Main Menu Table of Contents Lights 5. Put the socket back into the light assembly, and turn it clockwise to lock it in place. Replacing a High-mount Brake Light Bulb 6. Put the cover back on the light assembly. Push it in until it locks in place. 1. Open the tailgate. Remove the light assembly cover by pushing in on the tabs on both sides and pulling the cover off. 2. Remove the socket from the light assembly by turning it one-quarter turn counterclockwise. BULB Maintenance COVER 3.
Main Menu Table of Contents Cleaning the Seat Belts, Floor Mats Cleaning the Seat Belts LOOP If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle. 208 Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.
Main Menu Table of Contents Floor Mats, Audio Antenna, Dust and Pollen Filter If you remove a floor mat, make sure to re-anchor it when you put it back in your vehicle. Audio Antenna If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats. Your vehicle is equipped with an antenna on the f ront right f ender.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used. Do not open the hood when the wiper arms are raised, or you will damage the hood and the wiper arms. REAR FRONT WIPER ARMS LOCK TAB 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades, Tires BLADE BLADE Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced. REINFORCEMENT 4. Examine the new wiper blades.
Main Menu Table of Contents Tires Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly. We recommend that you visually check your tires every day.
Main Menu Table of Contents Tires Recommended Tire Pressures The following chart shows the recommended cold tire pressures for most normal and high-speed driving conditions. Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. INDICATOR LOCATION MARKS You should look for: Tire Size 215/65R16 98T Cold Tire Pressure for Normal Driving Front/Rear: 29 psi (200 kPa , 2.0 kgf/cm ) Cuts, splits, or cracks in the side of the tire.
Main Menu Table of Contents Tires Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life.
Main Menu Table of Contents Tires If you ever replace a wheel, make sure the new one matches the specifications of the original. Replacement wheels are available at your dealer. Always use the size and type of tires recommended in this owner’s manual. Wheels: 16 x 6 1/2JJ Tires: 215/65R16 98T See page 248 for information about DOT Tire Quality Grading, and page 250 for tire size and labeling information.
Main Menu Table of Contents Tires Tire Chains Because your vehicle has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices, with rubber chain tensioners, on the front tires. Use traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Metal linktype ‘‘chains’’ should not be used. When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can.
Main Menu Table of Contents Checking the Battery TEST INDICATOR WINDOW cloth or paper towel. Coat the terminals with grease to help prevent future corrosion. If additional battery maintenance is needed, see your dealer or a qualified technician. WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds. Wash your hands after handling. Check the terminals for corrosion (a white or yellowish powder).
Main Menu Table of Contents Vehicle Storage If you need to park your vehicle for an extended period (more than 1 month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors. Block the rear wheels. If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground. Fill the fuel tank.
Main Menu Taking Care of the Unexpected This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed. Changing a Flat Tire ..................... 220 If the Engine Won’t Start .............. 227 Jump Starting ............
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area that is far away from the traffic lanes. The vehicle can easily roll off the jack, seriously injuring anyone underneath. Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack. 220 1. Park the vehicle on firm, level, and non-slippery ground.
Main Menu Table of Contents Changing a Flat Tire 5. Turn the jack’s end bracket counterclockwise to loosen it, then remove the jack and tools. TOOL Soft vinyl spare tire cover If equipped 6. Remove the spare tire cover. Do not forcibly pull off the cover or you may damage it. COVER JACK 7. Zip the cover open. 8. Pull out the cover’s two lower flaps. Pull the upper flaps out by gradually working your hands up the sides of the cover. Remove the cover. CONTINUED 221 Taking Care of the Unexpected 4.
Main Menu Table of Contents Changing a Flat Tire Hard plastic spare tire cover If equipped NUTS CENTER SPACER 7. Unzip the flap around the lower edge of the cover. 8. Pull out the bottom of the cover, then gradually pull it off. 222 JACKING POINT 9. Pull off the center spacer. Using 11.Place the jack under the jacking the wheel wrench, loosen the point nearest the tire you need to three wheel nuts and remove them. change.
Main Menu Table of Contents Changing a Flat Tire 15.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten them fully. 16.Lower the vehicle to the ground, and remove the jack. EXTENSION WHEEL NUT WRENCH 13.Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving.
Main Menu Table of Contents Changing a Flat Tire 20.Store the jack in its holder. Turn the jack’s end bracket to lock it in place. Store the tools, and install the cover on the side of the cargo area. Loose items can fly around the interior in a crash and could seriously injure the occupants. CENTER SPACER 17.Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Main Menu Table of Contents Changing a Flat Tire Soft vinyl spare tire cover If equipped Make sure the cover is at room temperature bef ore you install it. If it’s too cold, it won’t f it easily over the tire. OUTSIDE SEAM 24.Step back to check the alignment of the logo. If needed, pivot the cover until the logo is straight. 25.Starting at the top of the tire, position the outside seam of the cover slightly over the outside edge of the tire.
Main Menu Table of Contents Changing a Flat Tire Hard plastic spare tire cover If equipped SPARE TIRE BRACKET 26.Pull the bottom of the cover over the tire. 27.If needed, readjust the cover to smooth out any wrinkles. 28.Zip the cover closed. 226 29.Place the top of the cover over the spare tire, then gradually push the bottom of the cover over the bottom of the tire. 30.Make sure the cover is horizontal. If needed, pivot the cover until the cover is horizontal. 31.Zip the cover closed.
Main Menu Table of Contents If the Engine Won’t Start Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the ignition switch to the START (III) position: You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly. Check the transmission interlock. If you have a manual transmission, the clutch pedal must be pushed all the way to the floor or the starter will not operate.
Main Menu Table of Contents If the Engine Won’t Start The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to the START (III) position, but the engine does not run. Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page 71 ). Are you using the proper starting procedure? Refer to Starting the Engine on page 158 .
Main Menu Table of Contents Jump Starting Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery. If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture. 2.
Main Menu Table of Contents Jump Starting 6. If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle. 7. Start your vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact. BRACKET 4. Remove the power steering reservoir from the bracket. Pull it away from the grounding strap. Make sure the power steering hose is not touching the power steering belt or the pulley. 230 5.
Main Menu Table of Contents If the Engine Overheats The pointer of the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.). If the vehicle overheats, you should take immediate action. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood. Do not open the hood if steam is coming out. 1.
Main Menu Table of Contents If the Engine Overheats 5. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Emergency Towing on page 242 ). 6. If you don’t find an obvious leak, check the coolant level in the radiator reserve tank (see page 146 ). 7. If there was no coolant in the reserve tank, you may need to add coolant to the radiator.
Main Menu Table of Contents Low Oil Pressure Indicator, Charging System Indicator 1. Safely pull off the road, and shut off the engine. Turn on the hazard warning lights. Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped. 3. If necessary, add oil to bring the level back to the full mark on the dipstick (see page 193 ). 2. Let the vehicle sit for a minute.
Main Menu Table of Contents Malfunction Indicator Lamp If the indicator comes on while driving, it means one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage. If you have recently refueled your vehicle, the indicator could come on because of a loose or missing fuel fill cap.
Main Menu Table of Contents Brake System Indicator U.S. Canada The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position, and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake. If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads.
Main Menu Table of Contents Closing the Moonroof If equipped If the electric motor will not close the moonroof, do the following: TAB NOTCH SOCKET 1. Check the fuse for the moonroof motor (see page 237 ). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the cargo area. ROUND PLUG 4.
Main Menu Table of Contents Fuses INTERIOR The vehicle’s fuses are contained in three fuse boxes. TAB The primary under-hood fuse box is in the engine compartment on the driver’s side. To open it, push the tabs as shown. UNDER-HOOD (SECONDARY) The secondary fuse box is next to the primary fuse box. Taking Care of the Unexpected The interior fuse box is underneath the steering column. To remove the fuse box lid, pull it toward you and take the lid out of its hinges.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages 240 and 241 , or the diagram on the fuse box lid, which fuse or fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works. 1. Turn the ignition switch to the LOCK (0) position.
Main Menu Table of Contents Fuses If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio). If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong.
Main Menu Table of Contents Fuse Locations INTERIOR FUSE BOX No. Amps. No. Amps. 1 2 3 4 5 15 A 10 A 10 A 10 A − 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Circuits Protected Ignition Coil Rear Accessory Power Socket Daytime running lights* ACG Not Used * 240 7.5 A 20 A 7.5 A 7.5 A 7.5 A − 7.5 A 10 A 10 A 15 A 20 A 15 A 15 A 7.
Main Menu Table of Contents Fuse Locations UNDER-HOOD FUSE BOXES PRIMARY Primary Fuse Box No. Amps. Circuits Protected 1 2 3 4 5 6 7 8 9 10 11 12 13 20 A 30 A 15 A 20 A 15 A 15 A 15 A 15 A 10 A 30 A 20 A 40 A 40 A Condenser Fan Engine Interior Light Cooling Fan Hazard Small Light Horn, Stop DBW Back Up ABS Motor Rear Defroster Heater Motor Power Window No. Amps. 40 A 14 20 A 15 20 A 16 20 A 17 30 A 18 100 A 19 50 A 20 21−25 7.
Main Menu Table of Contents Emergency Towing If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous. The only way you can safely tow your vehicle is with flat-bed equipment. The operator will load your vehicle on the back of a truck. Any other method of towing will damage the drive system. When you contact the towing agency, inform them a flat-bed is required.
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your vehicle, and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Identification Numbers ................. 244 Specifications ................................. 246 DOT Tire Quality Grading (U.S. Vehicles) ....................... 248 Uniform Tire Quality Grading ...................................
Main Menu Table of Contents Identification Numbers Your vehicle has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is the 17-digit number your Honda dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
Main Menu Table of Contents Identification Numbers The engine number is stamped into the front of the engine block. AUTOMATIC TRANSMISSION NUMBER The transmission number is on a label on top of the transmission.
Main Menu Table of Contents Specifications Dimensions Length 181.0 in (4,597 mm) 181.8 in (4,617 mm)*1 70.2 in (1,782 mm) Width 66.2 in (1,682 mm) Height 103.1 in (2,620 mm) Wheelbase Front 60.4 in (1,533 mm) Track Rear 60.6 in (1,538 mm) *1 : U.S. SE model and Canada EX-L model Weights Gross vehicle weight rating Engine Type Bore x Stroke Displacement Compression ratio Spark plugs Capacities Fuel tank Engine oil 246 See the certification label attached to the driver’s doorjamb.
Main Menu Table of Contents Specifications Air Conditioning Refrigerant type Charge quantity Lubricant type Lights Headlights High/Low Front turn signal lights Parking lights/side marker lights Rear turn signal lights Stop/Taillights Back-up lights License plate light Ceiling light Spotlights Cargo area Light Rear side marker lights High-mount brake light Fuses Interior See page 240 or the fuse label attached to the inside of the fuse box door under the steering column.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Main Menu Table of Contents Tire Labeling The tires that came on your vehicle have a number of markings. Those you should be aware of are described below. 98 − Load index (a numerical code associated with the maximum load the tire can carry). T Tire Size Whenever tires are replaced, they should be replaced with tires of the same size. Below is an example of tire size with an explanation of what each component means. − Speed symbol (an alphabetical code indicating the maximum speed rating).
Main Menu Table of Contents Emissions Controls The burning of gasoline in your vehicle’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, ignition timing control, and three way catalytic converter. These three systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that come out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Main Menu Table of Contents State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the onboard diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Main Menu Warranty and Customer Relations 255 Warranty and Customer Relations Customer Service Information ................................. 256 Warranty Coverages ..................... 257 Reporting Safety Defects (U.S. Vehicles) ........................... 258 Authorized Manuals ......................
Main Menu Table of Contents Customer Service Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The service manager or general manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new vehicle is covered by these warranties: Emissions Control Systems Defects Warranty and Emissions Performance Warranty − these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional. Please read your warranty booklet for exact information. Original Equipment Battery Limited Warranty − this warranty gives up to 100 percent credit toward a replacement battery.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc. 258 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The publications shown below can be purchased from Helm Incorporated. You can order in any of three ways: Detach and mail the order form on the right half of this page Call Helm Inc. at 1-800-782-4356 (credit card orders only) Go online at www. helminc. com If you are interested in other years or models, contact Helm Inc. at 1-800-782-4356. Publication Form Number 61S9A04 Form Description Price Each* $75.
Main Menu Table of Contents Authorized Manuals NOTE: Dealers and companies, please provide dealer or company name, and the name of the person to whose attention the shipment should be sent. For purchases outside U.S.A. please write to the address shown below for a quotation. S H I P T O Customer Name Attention Street Address − No P.O.
Main Menu Index A B Battery Charging System Indicator............................ 56, 233 Jump Starting ............................. 229 Maintenance ............................... 217 Specifications ............................. 247 Before Driving ............................... 141 Belts, Seat ..................................... 8, 18 Beverage Holders ............................ 91 Booster Seats ................................... 47 Brakes Anti-lock System (ABS) ............
Main Menu Index Cargo, How to Carry ..................... 150 Cassette Player Care ..................................... 115, 131 Operation ............................ 113, 129 CAUTION, Explanation of ............... ii CD Care .......................................... 134 CD Changer ........................... 111, 125 CD Changer Error Messages ............................ 112, 128 CD Error Messages ...................... 112 CD Player ............................... 109, 124 Center Pocket .............
Main Menu Index Disc Care ........................................ 134 Disc Changer ......................... 111, 125 Care ............................................ 134 Operation ............................ 111, 125 Disc Changer Error Message .............................. 112, 128 Disc Player Error Message .......... 112 Disposal of Used Oil ...................... 195 Doors Childproof Door Locks ............... 73 Locking and Unlocking ............... 73 Power Door Locks .......................
Main Menu Index Fluids Automatic Transmission........... 199 Brake ........................................... 201 Clutch .......................................... 202 Manual Transmission ............... 200 Power Steering........................... 202 Windshield Washer ................... 198 Folding Rear Seat ...................... 82, 83 Four-way Flashers ........................... 67 Front Airbags ............................... 9, 23 Front Seat Adjusting .......................................
Main Menu Index Inflation, Proper Tire .................... 212 Recommended Pressures ......... 213 Inside Mirror .................................... 88 Inspection, Tire .............................. 213 Installing a Child Seat ..................... 40 Instrument Panel ............................. 55 Instrument Panel Brightness ......... 67 Instruments and Controls ............... 53 Interior Lights .................................. 95 Introduction .........................................
Main Menu Index M Maintenance ................................... 183 Owner’s Maintenance Checks .................................... 186 Record .................................. 189-191 Required Indicator ....................... 60 Safety........................................... 184 Schedule .............................. 187-188 Malfunction Indicator Lamp .. 56, 234 Manual Transmission.................... 159 Checking Fluid Level ................ 200 Shifting ........................................
Main Menu Index Using Child Seats with Tethers...................................... 45 Using LATCH .............................. 41 R S Safety Belts................................... 8, 18 Safety Defects, Reporting* .......... 258 Safety Features .................................. 7 Airbags ............................................ 9 Seat Belts ........................................ 8 Safety Labels, Location of .............. 51 Safety Messages ................................ ii Seat Belts .....
Main Menu Index Side Airbags ................................. 9, 26 How Your Side Airbags Work.... 26 How the Side Airbag Off Indicator Works ....................... 29 Side Curtain Airbags ................... 9, 28 How Your Side Curtain Airbags Work.......................................... 28 Side Marker Lights, Bulb Replacement ............................... 205 Signaling Turns ................................ 66 Snow Tires ...................................... 215 Sound System ......................
Main Menu Index Transmission Checking Fluid Level, Automatic ............................... 199 Checking Fluid Level, Manual .................................... 200 Fluid Selection ................... 199, 200 Identification Number............... 245 Shifting the Automatic .............. 161 Shifting the Manual ................... 159 Treadwear ...................................... 248 Trip Meter ........................................ 61 Turn Signals .....................................
Main Menu Index Windshield Cleaning ........................................ 65 Defroster .................................... 101 Washers ...................................... 198 Wipers, Windshield Changing Blades ........................ 210 Operation ...................................... 65 Worn Tires ..................................... 213 Wrecker, Emergency Towing ...... 242 * X : U.S.
Main Menu Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 87 or higher. Fuel Tank Capacity: 15.3 US gal (58 ) Recommended Engine Oil: API Premium grade 5W-20 detergent oil (see page 193 ). Oil change capacity (including filter): 4.4 US qt (4.2 ) Automatic Transmission Fluid: Honda ATF-Z1 (Automatic Transmission Fluid) preferred, or a DEXRON III ATF as a temporary replacement (see page 199 ).