2007 Honda S2000 Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction .........................................................................................................................................i A Few Words About Safety..............................................................................
Main Menu Owner’s Identification This owner’s manual should be considered a permanent part of the vehicle and should remain with the vehicle when it is sold. OWNER ADDRESS STREET CITY STATE/PROVINCE ZIP CODE/ POSTAL CODE V. I. N. DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME DEALER NO. ADDRESS STREET CITY OWNER’S SIGNATURE DEALER’S SIGNATURE STATE/PROVINCE ZIP CODE/ POSTAL CODE This owner’s manual covers all models of the S2000.
Main Menu Introduction Congratulations on your selection of the 2007 Honda S2000. We are certain you will be pleased with your purchase of one of the most sophisticated and technologically-advanced sports cars in the world. One of the best ways to enhance the enjoyment of your new vehicle is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your vehicle so you can refer to it at any time.
Main Menu Introduction California Proposition 65 Warning WARNING: This product contains or emits chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. Event Data Recorders This vehicle is equipped with one or more devices commonly referred to as event data recorders. These devices record seat belt use, passenger seat occupancy, airbag deployment data, and the failure of any airbag system component.
Main Menu A Few Words About Safety Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining your vehicle.
Main Menu Your Vehicle at a Glance PASSENGER AIRBAG OFF INDICATOR (P.26) Your Vehicle at a Glance INSTRUMENT PANEL INDICATORS (P.46) GAUGES (P.51) PASSENGER’S FRONT AIRBAG (P.9, 20) DRIVER’S FRONT AIRBAG (P.9, 20) AUDIO SYSTEM (P.88) POWER DOOR LOCK (P.63) MANUAL TRANSMISSION (P.125) POWER WINDOW SWITCHES (P.68) HAZARD WARNING BUTTON (P.58) MIRROR CONTROLS (P.75) ROOF SWITCH (P.71) REAR WINDOW DEFOGGER BUTTON (P.
Main Menu Your Vehicle at a Glance HEADLIGHTS/TURN SIGNALS (P.57) CLOCK BUTTON (P.54) INSTRUMENT PANEL BRIGHTNESS (P.58) VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.131) REMOTE AUDIO CONTROLS (P.104) HEATING/COOLING CONTROLS (P.84) ENGINE START BUTTON (P.124) WINDSHIELD WIPERS/ WASHERS (P.56) HOOD RELEASE HANDLE (P.112) 4 CRUISE BUTTON (P.106) HORN CRUISE CONTROL BUTTONS (P.
Main Menu Driver and Passenger Safety Important Safety Precautions .......... 6 Your Vehicle’s Safety Features........ 7 Seat Belts ........................................ 8 Airbags ............................................ 9 Protecting Adults and Teens.......... 10 1. Close and Lock the Doors ...... 10 2. Adjust the Seats ....................... 10 3. Adjust the Seat-Backs ............. 11 4. Fasten and Position the Seat Belts .............................. 12 5. Maintain a Proper Sitting Position ...
Main Menu Table of Contents Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. If an older child must ride in this vehicle, follow all child safety instructions and warnings in this manual (see pages 29 − 40 ). Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions.
Main Menu Table of Contents Your Vehicle’s Safety Features (1) (9) (8) (3) (4) (7) (8) (2) (5) (2) (1) Safety Cage (2) Crush Zones (3) Seats and Seat-Backs (4) Head Restraints (5) Collapsible Steering Column (6) Seat Belts (7) Seat Belt Tensioners (8) Front Airbags (9) Door Locks Some features do not require any action on your part.
Main Menu Table of Contents Your Vehicle’s Safety Features Seat Belts Your vehicle is equipped with seat belts in both seating positions. Your seat belt system also includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts have proven to be the single most effective safety device for adults and larger children.
Main Menu Table of Contents Your Vehicle’s Safety Features Airbags The most important things you need to know about your airbags are: Airbags offer no protection in side impacts, rear impacts, rollovers, or minor frontal collisions. Airbags can pose serious hazards.
Main Menu Table of Contents Protecting Adults and Teens Introduction The following pages provide instructions on how to properly protect the driver, an adult passenger or teenage child large enough and mature enough to drive or ride in your vehicle. See pages 29 − 40 for important guidelines on how to properly protect a child in a forward-facing child seat or a larger child passenger.
Main Menu Table of Contents Protecting Adults and Teens If you cannot get far enough away from the steering wheel and still reach the controls, we recommend that you investigate whether some type of adaptive equipment may help. Once your seat is adjusted correctly, rock it back and forth to make sure the seat is locked in position. See page 67 for how to adjust the seats. 3.Adjust the Seat-Backs Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate.
Main Menu Table of Contents Protecting Adults and Teens Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant’s chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury. 4.
Main Menu Table of Contents Protecting Adults and Teens Improperly positioning the seat belts can cause serious injury or death in a crash. Make sure all seat belts are properly positioned before driving. Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause very serious injuries in a crash. If a seat belt does not seem to work properly, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt.
Main Menu Table of Contents Protecting Adults and Teens In addition, an occupant who is out of position can be seriously or fatally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag. Advice for Pregnant Women When driving, remember to sit upright and adjust the seat as far back as possible while allowing full control of the vehicle. When riding as a passenger, adjust the seat as far back as possible.
Main Menu Table of Contents Protecting Adults and Teens Additional Safety Precautions Two people should never use the same seat belt. If they do, they Do not put any accessories on seat belts. Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can reduce the protective capability of the belt and increase the chance of serious injury in a crash.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in both seating positions. The seat belts are also equipped with automatic seat belt tensioners. This system uses the same sensors as the front airbags to monitor whether the seat belts are latched or unlatched, and how much weight is on the passenger’s seat (see page 24 ).
Main Menu Table of Contents Additional Information About Your Seat Belts To fasten the belt, insert the latch plate into the buckle, then tug on the belt to make sure the buckle is latched (see page 12 for how to properly position the belt). To unlock the belt, press the red PRESS button on the buckle. Guide the belt across your body so that it retracts completely. After exiting the vehicle, be sure the belt is out of the way and will not get closed in the door.
Main Menu Table of Contents Additional Information About Your Seat Belts Automatic Seat Belt Tensioners The tensioners are designed to activate primarily in frontal collisions, and they should activate in any collision severe enough to cause airbag inflation. However, the tensioners can be activated during a collision in which the airbags do not deploy. In this case, the airbags would not be needed, but the additional restraint could be helpful.
Main Menu Table of Contents Additional Information About Your Seat Belts Not checking or maintaining seat belts can result in serious injury or death if the seat belts do not work properly when needed. Driver and Passenger Safety The dealer should also inspect the anchors for damage and replace them if needed. If the automatic seat belt tensioners activate during a crash, they must be replaced. Check your seat belts regularly and have any problem corrected as soon as possible.
Main Menu Table of Contents Additional Information About Your Airbags Airbag System Components (8) (2) (9) (1) (1) Driver’s Front Airbag (2) Passenger’s Front Airbag (3) Control Unit (4) Seat Belt Tensioners (5) Driver’s Seat Position Sensor (6) Passenger’s Weight Sensors (7) Passenger’s Weight Sensor Unit (8) Front Impact Sensors (9) Passenger Airbag Off Indicator 20 (4) (3) (6) (5) (6) (7) (4)
Main Menu Table of Contents Additional Information About Your Airbags Your airbag system includes: Automatic seat belt tensioners (see page 18 ). Sensors that can detect a moderate to severe front impact. Sensors that can detect whether the driver’s seat belt and the passenger’s seat belt are latched or unlatched (see page 16 ). A driver’s seat position sensor that monitors the distance of the seat from the airbag. If the seat is too far forward, the airbag will inflate with less force (see page 24 ).
Main Menu Table of Contents Additional Information About Your Airbags How Your Airbags Work During a frontal crash, your seat belt restrains your lower body and torso, and the front airbag helps protect your head and chest. Although both airbags normally inflate within a split second of each other, it is possible for only one airbag to deploy. If you ever have a moderate to severe frontal collision, sensors will detect the vehicle’s rapid deceleration.
Main Menu Table of Contents Additional Information About Your Airbags Dual-Stage Airbags Dual-Threshold Airbags Your front airbags are dual-stage airbags. This means they have two inflation stages that can be ignited sequentially or simultaneously, depending on crash severity. Your front airbags are also dualthreshold airbags. Airbags with this feature have two deployment thresholds that depend on whether sensors detect the occupant is wearing a seat belt or not.
Main Menu Table of Contents Additional Information About Your Airbags Advanced Airbags Your airbags are also advanced airbags. The main purpose of this feature is to help prevent airbagcaused injuries to short drivers and children who ride in the passenger’s seat. For both advanced airbags to work properly: DRIVER’S SEAT POSITION SENSOR PASSENGER’S SEAT WEIGHT SENSOR Occupants must sit upright and wear their seat belts properly.
Main Menu Table of Contents Additional Information About Your Airbags If the weight sensors detect there is no passenger in the seat, the airbag will be off. However, the passenger airbag off indicator will not come on. To ensure that the passenger’s advanced airbag system will work properly, do not do anything that would increase or decrease the weight on the passenger’s seat, such as hanging heavy objects on the seat.
Main Menu Table of Contents Additional Information About Your Airbags If you see any of these indications, the airbags and seat belt tensioners may not work properly when you need them. Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly. Have your vehicle checked by a dealer as soon as possible if the SRS indicator alerts you to a possible problem. 26 How the Passenger Airbag Off Indicator Works U. S.
Main Menu Table of Contents Additional Information About Your Airbags If this happens, adjust the seat as far to the rear as possible and have the passenger sit upright and wear the seat belt properly. If the indicator comes on with no passenger and no objects on the passenger seat, or with an adult riding there, something may be interfering with the weight sensors. Look for and remove: Any items under the passenger’s seat. Any objects hanging on the seat. Any object touching the rear of the seat-back.
Main Menu Table of Contents Additional Information About Your Airbags The SRS indicator alerts you to a problem. Take your vehicle to an authorized dealer as soon as possible. If you ignore this indication, your airbags may not operate properly. If your vehicle has a moderate to severe impact.
Main Menu Table of Contents Protecting Children − General Guidelines If you ever need to drive with a child in your vehicle, be sure to read this section. It begins with important general guidelines, then presents special information for small children who must ride in a forwardfacing child seat, and for larger children. All Children Must Be Restrained Each year, many children are injured or killed in vehicle crashes because they are either unrestrained or not properly restrained.
Main Menu Table of Contents Protecting Children − General Guidelines Your Vehicle is Not Recommended for Child Passengers The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in a back seat. The Passenger’s Airbag Can Pose Serious Risks Airbags have been designed to help protect adults in a moderate to severe frontal collision.
Main Menu Table of Contents Protecting Children − General Guidelines U.S. Models Sun Visor Dashboard Driver and Passenger Safety To remind you of the passenger’s airbag hazards, your vehicle has warning labels on the dashboard (U.S. models) and on the driver’s and passenger’s visors. Please read and follow the instructions on these labels.
Main Menu Table of Contents Protecting Children − General Guidelines Additional Safety Precautions Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward and crush the child against the dashboard. If you are wearing a seat belt, the child can be torn from your arms and be seriously hurt or killed. Never put a seat belt over yourself and a child. During a crash, the belt could press deep into the child and cause serious or fatal injuries.
Main Menu Table of Contents Protecting Small Children We also recommend that a small child use the child seat until the child reaches the weight or height limit for the seat. If you decide to transport a small child in this vehicle, be sure to move the passenger seat as far to the rear as possible, and follow the instructions and guidelines in the following pages. Placing a forward-facing child seat in the passenger’s seat can result in serious injury or death if the airbag inflates.
Main Menu Table of Contents Selecting a Child Seat, Installing a Child Seat Selecting a Child Seat To provide proper protection, a child seat should meet three requirements: Installing a Child Seat After selecting a proper child seat, there are three main steps in installing a child seat: 1. The child seat should meet U.S. or Canadian Motor Vehicle Safety Standard 213. Look for FMVSS 1. Properly secure the child seat to the vehicle.
Main Menu Table of Contents Installing a Child Seat 1. Move the vehicle seat to the rearmost position. Moving the seat as far back as possible reduces the chance of a child being injured or killed if the passenger’s airbag inflates. 2. With the child seat in position, route the belt through the child seat according to the seat maker’s instructions, then insert the latch plate into the buckle. 4. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out.
Main Menu Table of Contents Installing a Child Seat To deactivate the lockable retractor and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 5. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Larger Children Since this vehicle does not have a back seat, we recommend that you do not carry a larger child, age 12 or under, as a passenger. However, the following pages provide guidelines to help you decide when a given child may ride in this vehicle, and how to properly protect the child. Checking Seat Belt Fit Allowing a larger child age 12 or under to ride in the vehicle can result in injury or death if the passenger’s airbag inflates.
Main Menu Table of Contents Protecting Larger Children 3. Does the shoulder belt cross between the child’s neck and arm? Using a Booster Seat Booster seats can be high-back or low-back. Whichever style you select, make sure the booster meets federal safety standards and that you follow the booster seat maker’s instructions. 4. Is the lap part of the belt as low as possible, touching the child’s thighs? 5.
Main Menu Table of Contents Protecting Larger Children Physically, a child must be large enough for the lap/shoulder belt to properly fit (see page 37 ). If the seat belt does not fit properly, with or without the child sitting on a booster, the child should not sit in this vehicle. If the passenger’s airbag inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position.
Main Menu Table of Contents Protecting Larger Children Additional Safety Precautions Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured. Two children should never use the same seat belt.
Main Menu Table of Contents Carbon Monoxide Hazard Have the exhaust system inspected for leaks whenever: Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide. The vehicle is raised for an oil change. You notice a change in the sound of the exhaust. The vehicle was in an accident that may have damaged the underside.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. SUN VISOR U.S. models Canadian models If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact your dealer for a replacement. SEAT BELT TENSIONER DASHBOARD BATTERY U.S. models only U.S.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach. Trunk................................................. 63 Emergency Trunk Opener ......... 64 Remote Transmitter ........................ 65 Seats .................................................. 67 Power Windows ............................... 68 Convertible Top ...............................
Main Menu Table of Contents Control Locations HEATING/COOLING CONTROLS (P.84) HOOD RELEASE HANDLE (P.112) CRUISE CONTROL BUTTONS (P.106) POWER DOOR LOCK (P.63) AUDIO SYSTEM (P.88) PARKING BRAKE (P.76) POWER WINDOW SWITCHES (P.68) HAZARD WARNING BUTTON (P.58) MIRROR CONTROLS (P.75) MANUAL TRANSMISSION (P.125) 44 ROOF SWITCH (P.71) ACCESSORY POWER SOCKET (P.78) REAR WINDOW DEFOGGER BUTTON (P.
Main Menu Table of Contents Instrument Panel TURN SIGNAL AND HAZARD WARNING INDICATORS (P.48) VSA ACTIVATION INDICATOR (P.50) OUTSIDE TEMPERATURE INDICATOR (P.53) HIGH BEAM INDICATOR (P.49) ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR (P.47) DAYTIME RUNNING LIGHTS INDICATOR (P.48) LOW FUEL INDICATOR (P.49) SEAT BELT REMINDER INDICATOR (P.46) ELECTRIC POWER STEERING (EPS) INDICATOR (P.48) PARKING BRAKE AND BRAKE SYSTEM INDICATOR＊ (P.46, 188) DOOR-OPEN INDICATOR (P.47) TRUNK-OPEN INDICATOR (P.
Main Menu Table of Contents Instrument Panel Indicators The instrument panel has many indicators to give you important information about your vehicle. Seat Belt Reminder Indicator This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passenger to fasten your seat belts. A beeper also sounds if you and your passenger have not fastened your seat belts.
Main Menu Table of Contents Instrument Panel Indicators Anti-lock Brake System (ABS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when you push the START button. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. For more information, see page 128 .
Main Menu Table of Contents Instrument Panel Indicators Electric Power Steering (EPS) Indicator This indicator normally comes on when you turn the ignition to the ON (II) position and goes off after the engine starts. If it comes on at any other time, there is a problem in the electric power steering system. If this happens, stop the vehicle in a safe place and turn off the engine. Reset the system by restarting the engine. The indicator will not turn off immediately.
Main Menu Table of Contents Instrument Panel Indicators High Beam Indicator This indicator comes on with the high beam headlights. For more information, see page 57 . Low Fuel Indicator This indicator comes on as a reminder that you must refuel soon. When the indicator comes on, there is about 2.22 US gal (8.4 ) of fuel remaining in the tank before the reading reaches E. There is a small reserve of fuel remaining in the tank when the reading does reach E.
Main Menu Table of Contents Instrument Panel Indicators Vehicle Stability Assist (VSA) System Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked.
Main Menu Table of Contents Gauges TACHOMETER OUTSIDE TEMPERATURE INDICATOR SPEEDOMETER TEMPERATURE GAUGE CLOCK BUTTON To reset a trip meter, display it, and then press and hold the TRIP button until you hear a beep and the number resets to ‘‘0.0’’. FUEL GAUGE − BUTTON CLOCK TRIP METER ＋ BUTTON ODOMETER/CHECK FUEL CAP INDICATOR Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S.
Main Menu Table of Contents Gauges Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter. 52 Check Fuel Cap Message Your vehicle’s on board diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak.
Main Menu Table of Contents Gauges Outside Temperature Indicator This indicator displays the outside temperature in Fahrenheit (U.S. models) or Centigrade (Canadian models). The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).
Main Menu Table of Contents Gauges Maintenance Minder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued troublefree driving. Refer to page 135 for more information. Clock The clock displays the time with the ignition switch in the ON (II) position. To set the clock: 1.
Main Menu Table of Contents Controls Near the Steering Wheel HEADLIGHTS/TURN SIGNALS (P.57) CLOCK BUTTON (P.54) INSTRUMENT PANEL BRIGHTNESS (P.58) VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.131) ENGINE START BUTTON (P.124) HEATING/COOLING CONTROLS (P.84) WINDSHIELD WIPERS/WASHERS (P.56) HOOD RELEASE HANDLE (P.112) CRUISE CONTROL BUTTONS (P.106) CRUISE BUTTON (P.106) ＊ HORN＊ To use the horn, press the pad around the ‘‘H’’ logo. 55 Instruments and Controls REMOTE AUDIO CONTROLS (P.
Main Menu Table of Contents Windshield Wipers and Washers Push the right lever up or down to select a position. MIST − The wipers run at high speed until you release the lever. OFF − The wipers are not activated. INT − The wipers operate every few seconds. In low speed and high speed, the wipers run continuously. LO − The wipers run at low speed. 1. MIST 2. OFF 3. INT − Intermittent 4. LO − Low speed 5. HI − High speed 6. Windshield washers 56 HI − The wipers run at high speed.
Main Menu Table of Contents Turn Signal and Headlights Headlights On − Turning the switch to the ‘‘ ’’ position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. 1. Turn Signal 2. Off 3. Parking and indicator lights 4. Headlights on 5. High beams 6. Flash high beams Turning the switch to the ‘‘ ’’ position turns on the headlights.
Main Menu Table of Contents Instrument Panel Brightness, Hazard Warning Button Instrument Panel Brightness The buttons in the lower left corner of the instrument panel adjust the brightness of the display in five steps. Push the ＋ or − button five times to see the full range. 58 To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the or position.
Main Menu Table of Contents Rear Window Defogger Do not push the defogger button when the convertible top is folded. Instruments and Controls Make sure the rear window is clear and you have good visibility before starting to drive. The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side. The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off.
Main Menu Table of Contents Keys and Locks MASTER KEYS VALET KEY KEY (BLACK) (GREY) NUMBER TAG The valet key works only in the ignition and the door locks. You can keep the trunk and the lower console compartment locked when you leave your vehicle and the valet key at a parking facility. You should have received a key number tag with your keys. You will need this key number if you ever have to get a key replaced. Use only Honda-approved key blanks. The master key fits all the locks on your vehicle.
Main Menu Table of Contents Immobilizer System The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable. If you lose your key and cannot start the engine, contact your dealer. As required by the FCC: This device complies with Part 15 of the FCC rules.
Main Menu Table of Contents Ignition Switch ACCESSORY (I) − You can operate the audio system and the accessory power socket in this position. The ignition switch has three positions: LOCK (0), ACCESSORY (I), and ON (II). LOCK (0) − You can insert or remove the key only in this position. To turn the key, push it in slightly. If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
Main Menu Table of Contents Power Door Locks, Trunk Power Door Locks LOCK TAB Both doors lock when you use the key in the driver’s door. Using the key in the passenger’s door only locks and unlocks that door. To unlock only the driver’s door from the outside, insert the key in the driver’s door lock, turn the key and release it. If you turn the key and hold it, both doors will unlock. Trunk Push TRUNK RELEASE BUTTON To open the trunk, press the trunk release button in the lower console compartment.
Main Menu Table of Contents Trunk Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 41 . Emergency Trunk Opener MASTER KEY You can also use the master key to open the trunk lock. To open the trunk with the remote transmitter, press and hold the TRUNK RELEASE button for about 1 second (see page 65 ).
Main Menu Table of Contents Remote Transmitter LED LOCK BUTTON UNLOCK BUTTON PANIC BUTTON LOCK − Press this button once to lock both doors. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked. UNLOCK − Press this button once to unlock the driver’s door. Push it twice to also unlock the passenger’s door.
Main Menu Table of Contents Remote Transmitter Replacing the Transmitter Battery BATTERY ROUND COVER If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible. Battery type: CR2025 66 To replace the battery, remove the round cover on the back of the transmitter by turning it counterclockwise with a coin. Insert a new battery with the ＋ side facing up. Align the ▽ mark on the cover with the ◎ mark on the transmitter.
Main Menu Table of Contents Seats See pages 10 − 12 for important safety information and warnings about how to properly position the seats and seatbacks. To adjust the seat forward and backward, pull up on the lever under the seat cushion’s front edge. Then try to move the seat to make sure it is locked in position. To change the seat-back angle, pull up on the lever on the outside of the seat bottom. 67 Instruments and Controls Make all seat adjustments before you start driving.
Main Menu Table of Contents Power Windows Turn the ignition switch to the ON (II) position to raise or lower either window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window. DRIVER’S WINDOW SWITCH Closing a power window on someone’s hands or fingers can cause serious injury. MAIN SWITCH PASSENGER’S WINDOW SWITCH The driver’s armrest has a master power window control panel.
Main Menu Table of Contents Power Windows The master control panel also contains these extra features: Instruments and Controls AUTO − To open the driver’s window fully, push the window switch firmly down to the second detent, and release it. The window automatically goes all the way down. To stop the window, pull back on the window switch briefly. If the MAIN switch is OFF, the passenger’s window cannot be raised or lowered.
Main Menu Table of Contents Convertible Top The convertible top on your vehicle lowers and raises electrically. It is advisable to raise the top whenever you park the vehicle. This helps to protect the vehicle from unexpected weather changes, and from theft of your valuables. Do not operate the convertible top in f reezing weather. You can damage the material and the mechanism. Do not operate the top if it is wet, dirty, or covered with ice or snow.
Main Menu Table of Contents Convertible Top Make sure that you, your passenger, or any other people around the vehicle are clear of the moving convertible top. LOCKING LEVER 4. With the latches released, push the locking levers up until they latch. ROOF SWITCH 5. Pull back and hold the ROOF switch. The windows lower and the roof folds back. Release the ROOF switch when the roof is retracted completely into the rear shelf. Do not sit on the f olded convertible top, or place any items on top of it.
Main Menu Table of Contents Convertible Top Convertible Top Cover Use the convertible top cover when the top is folded to help prevent foreign objects, dirt, etc., from getting into the material and the mechanism. SNAPS PIN The cover is attached to the body with four snaps: two behind the roll bars, and one on the side of each seat. To install or remove the convertible top cover correctly, do this: SNAP 1. Remove the convertible top cover from the trunk, and lay it into position behind the roll bar.
Main Menu Table of Contents Convertible Top Raising the Convertible Top FASTENER STRAP PIN 2. Turn the ignition switch to the ON (II) position. SNAP 4. Pull down the strap on the passenger’s side of the cover, and align its snap with the pin on the trim panel behind the door. Press on both sides of the snap to attach it to the pin. 5. Pull down the strap on the driver’s side of the cover, and align its snap with the pin on the trim panel behind the door.
Main Menu Table of Contents Convertible Top TAB LATCH LOCKING LEVER 4. Push in the tab to release the locking levers, and pull them down. Note the movement of the latch when you push in the tab. 5. While holding the lever down, push in the tab to engage the latch in the windshield header. Pull the top down and forward if necessary. 74 6. Push the locking levers up while holding the tab. When the latch is in place, release the tab. Make sure the convertible top is securely latched.
Main Menu Table of Contents Convertible Top, Mirrors To reduce the possibility of leaks: Do not lean or sit on an open door. Mirrors Adjusting the Power Mirrors SELECTOR SWITCH Do not push or pull the door glass to open and close the door. TAB ADJUSTMENT SWITCH Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. The inside mirror has day and night positions. The night position reduces glare from headlights behind you.
Main Menu Table of Contents Mirrors, Parking Brake 4. When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings. Parking Brake BUTTON PARKING BRAKE LEVER To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page 46 ).
Main Menu Table of Contents Interior Convenience Items CONSOLE COMPARTMENT ACCESSORY POWER SOCKET VANITY MIRROR/SUNVISOR Instruments and Controls AUDIO PANEL DRIVER’S SEAT-BACK POCKET BEVERAGE HOLDER DASHBOARD LOWER POCKET 77
Main Menu Table of Contents Interior Convenience Items Beverage Holder Accessory Power Socket PARTITION Open the beverage holder by pushing on the tab. The lid will slide open. To hold two cups in the beverage holder, flip the partition up. Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passenger. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.
Main Menu Table of Contents Interior Convenience Items Console Compartments The lever to open the upper compartment is inside the lower compartment. Push up the lever, and lift the lid. To close, lower the lid, and push it down until it latches. To open the audio panel, push on the top center, and let the panel swing down. To close, pivot the panel up, and push on it until it latches. 79 Instruments and Controls The area between the seats has two compartments.
Main Menu Table of Contents Interior Convenience Items, Interior Light Dashboard Lower Pocket Interior Light DOOR ACTIVATED The dashboard lower pocket is located next to the audio panel. The interior light has a threeposition switch; ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you: Open either door. Unlock the doors with the key or the remote transmitter.
Main Menu Table of Contents Interior Light Instruments and Controls When the switch is in the center position with both doors closed, the two bulbs in the interior light can each be turned on and off with the button next to it.
Main Menu
Main Menu Features The heating and air conditioning system in your vehicle provides a comfortable driving environment in all weather conditions. Your vehicle has an anti-theft audio system that requires a code number to enable it. 83 Features The standard audio system has many features. This section describes those features and how to use them. (If you have an optional audio system, refer to the operating instructions that came with it.) Vents, Heating, and A/C ................
Main Menu Table of Contents Vents, Heating, and A/C RECIRCULATION BUTTON REAR WINDOW DEFOGGER BUTTON MODE CONTROL DIAL AIR CONDITIONING BUTTON FAN CONTROL LEVER 84 TEMPERATURE CONTROL DIAL
Main Menu Table of Contents Vents, Heating, and A/C Airflow Controls Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow. Air Conditioning (A/C) Button This button turns the air conditioning on and off. The indicator in the button comes on when the A/C is on. The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.
Main Menu Table of Contents Vents, Heating, and A/C Air flows from the center vents in the dashboard above the audio system, the vents on both sides of the instrument panel, and from the floor vents. Select this position when you drive with the convertible top folded. Air flows from the floor vents and the vents on both sides of the instrument panel. Airflow is divided between the floor vents and the defroster vents at the base of the windshield, and the vents on both sides of the instrument panel.
Main Menu Table of Contents Vents, Heating, and A/C mode and turns on the A/C. 3. Adjust the temperature so the airflow feels warm. to help clear the 4. Select rear window. 5. To increase airflow to the windshield, close the corner vents. 1. Turn the fan on. 2. Turn on the air conditioning. and fresh air mode. 3. Select 4. Adjust the temperature to your preference. When you select or , the system automatically turns on the A/C. This helps to dehumidify the air and to defog the windshield.
Main Menu Table of Contents Playing the AM/FM Radio U.S.
Main Menu Table of Contents Playing the AM/FM Radio To Play the Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on by pushing the PWR/VOL knob or the AM/FM button. Adjust the volume by turning the same knob. To Select a Station You can use any of five methods to find radio stations on the selected band: tune, seek, scan, the preset buttons, and auto select. TUNE − Use the TUNE knob to tune the radio to a desired frequency.
Main Menu Table of Contents Playing the AM/FM Radio AUTO SELECT − If you are traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area. Press the A. SEL button. ‘‘A. SEL’’ flashes in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM and twelve FM stations in the preset buttons.
Main Menu Table of Contents AM/FM Radio Reception Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
Main Menu Table of Contents AM/FM Radio Reception As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter.
Main Menu Table of Contents Playing the XM Satellite Radio (Optional on U.S. Models) Optional on U.S. models Not available on Canadian models Your vehicle is capable of receiving XM Satellite Radio anywhere in the United States, except Hawaii and Alaska. AM/FM BUTTON TUNE KNOB CD/XM BUTTON SCAN BUTTON Features XM is a registered trademark of XM Satellite Radio, Inc. Satellite radio receives signals from two satellites to produce clear, highquality digital reception.
Main Menu Table of Contents Playing the XM Satellite Radio (Optional on U.S. Models) Playing the Satellite Radio To listen to satellite radio, turn the ignition switch to the ACCESSORY (I) or the ON (II) position. Push the PWR/VOL knob to turn on the audio system, and press the CD/XM button. Adjust the volume by turning the PWR/VOL knob. The last channel you listened to will show in the display.
Main Menu Table of Contents Playing the XM Satellite Radio (Optional on U.S. Models) To store a channel: Preset − You can store up to 12 preset channels using the six preset buttons. Each button stores one channel from the XM1 band and one channel from the XM2 band. 3. Pick the preset button you want for that channel. Press and hold the button until you hear a beep. To store a channel: 1. Press the CD/XM button. Either XM1 or XM2 will show in the display. 5. Press the CD/XM button again.
Main Menu Table of Contents Playing the XM Satellite Radio (Optional on U.S. Models) Signal may be blocked by mountains or large obstacles to the south. Signal is weaker in these areas. The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas.
Main Menu Table of Contents Playing the XM Satellite Radio (Optional on U.S. Models) Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions: Driving on the south side of an east/west mountain road. Driving in tunnels. Driving on a road beside a vertical wall, steep cliff, or hill to the south of you. Driving on the lower level of a multi-tiered road. Driving on a single lane road alongside dense trees taller than 50 ft.
Main Menu Table of Contents Playing a CD U.S.
Main Menu Table of Contents Playing a CD To Play a CD To load or play CDs, the ignition switch must be in the ACCESSORY (I) or the ON(II) position. Insert a CD about halfway into the CD slot. The drive will pull the CD in the rest of the way and begin to play it. When the system reaches the end of the disc, it will return to the beginning and play the disc again. To play the radio when a CD is playing, press the AM/FM button. Press the CD button again to switch back to the CD player.
Main Menu Table of Contents Playing a CD, CD Changer REPEAT − To continuously replay a track, press and release the RPT button. You will see RPT in the display. Press it again to turn it off. RANDOM − This feature plays the tracks in random order. To activate random play, press and release the RDM button. You will see RDM in the display. Press it again to return to normal play. To Stop Playing a CD Press the eject button ( ) to remove the CD.
Main Menu Table of Contents Protecting Your CDs Protecting Your CDs Protecting CDs General Information When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. When using CD-R discs, use only high quality CDs labeled for audio use. CD-RW discs will not work in this unit. Play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems.
Main Menu Table of Contents CD Player Error Messages The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. CD Player Error Messages Error Message Cause ＊1 FOCUS Error ＊2 ＊1 The audio system will try to play the disc.
Main Menu Table of Contents CD Changer Error Messages The chart on the right explains the error messages you may see in the display while playing a disc. Error Message Cause The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. ＊1 FOCUS Error ＊2 No CD in the CD magazine ＊1 Mechanical Error ＊2 ＊1 Insert a different disc. If the new disc plays, there is a problem with the first disc.
Main Menu Table of Contents Remote Audio Controls AUDIO CONTROL BUTTON CHANNEL BUTTON MUTE BUTTON VOLUME BAR Four controls for the audio system are on the left side of the dashboard by the instrument panel. These let you control basic functions without distracting your attention from driving. Use the VOLUME bar to adjust the volume. Push ＋ to increase the volume and − to decrease it. Hold the lever until the volume reaches the desired level, then release it.
Main Menu Table of Contents Radio Theft Protection You should have received a card that lists your audio system’s code and serial numbers. It is best to store this card in a safe place at home. In addition, you should write the audio system’s serial number in this owner’s manual. If you lose the card, you must obtain the code number from a dealer. To do this, you will need the system’s serial number.
Main Menu Table of Contents Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather. Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather.
Main Menu Table of Contents Cruise Control Changing the Set Speed You can increase the set cruising speed in any of these ways: Press and hold the RESUME/ accel button. When you reach the desired cruising speed, release the button. Push on the accelerator pedal. Accelerate to the desired cruising speed, and press the SET/decel button. To increase the speed in very small amounts, tap the RESUME/ accel button. Each time you do this, your vehicle speeds up about 1 mph (1.6 km/h).
Main Menu Table of Contents Cruise Control Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed. Resting your foot on the brake or clutch pedal causes the cruise control to cancel. Canceling Cruise Control You can cancel cruise control in any of these ways: Tap the brake or clutch pedal. Push the CANCEL button on the steering wheel.
Main Menu Before Driving Break-in Period .............................. 110 Fuel Recommendation .................. 110 Service Station Procedures .......... 111 Refueling..................................... 111 Opening and Closing the Hood ........................................ 112 Oil Check .................................... 113 Engine Coolant Check .............. 114 Fuel Economy ................................ 114 Accessories and Modifications .... 115 Carrying Cargo ..............................
Main Menu Table of Contents Break-in Period, Fuel Recommendation Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Do not exceed 5,500 rpm for the first 600 miles (1,000 km) of operation. Do not change the oil until the scheduled maintenance time. Avoid hard braking for the first 200 miles (300 km).
Main Menu Table of Contents Service Station Procedures Refueling Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. 4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘top off’’ the tank. Leave some room for the fuel to expand with temperature changes. If the fuel nozzle keeps clicking off even though the tank is not full, there may be a problem with your vehicle’s fuel vapor recovery system.
Main Menu Table of Contents Service Station Procedures 5. Screw the fuel fill cap back on until it clicks at least once. If you do not properly tighten the cap, the malfunction indicator lamp may come on (see page 187 ). You will also see a ‘‘CHECK FUEL CAP’’ message on the information display. Opening and Closing the Hood RELEASE HANDLE 6. Push the fuel fill door closed until it latches. 1. Park the vehicle, and set the parking brake.
Main Menu Table of Contents Service Station Procedures Oil Check GRIP DIPSTICK UPPER MARK SUPPORT ROD CLIP 3. Holding the grip, pull the support rod out of its clip. Insert the end into the designated hole in the hood. To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched.
Main Menu Table of Contents Service Station Procedures, Fuel Economy Engine Coolant Check Fuel Economy Improving Fuel Economy RESERVE TANK Always maintain your vehicle according to the maintenance messages displayed on the information display. See Owner’s Maintenance Checks on page 141 . For example, an underinflated tire causes more ‘‘rolling resistance,’’ which uses more fuel. MAX MIN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines.
Main Menu Table of Contents Accessories and Modifications Modifying your vehicle, or installing some non-Honda accessories, can make it unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Although non-Honda accessories may fit on your vehicle, they may not meet factory specifications, and could adversely affect your vehicle’s handling and stability. Follow all instructions in this owner’s manual regarding accessories and modifications.
Main Menu Table of Contents Accessories and Modifications Modifying Your Vehicle Removing parts from your vehicle, or replacing components with non-Honda components could seriously affect your vehicle’s handling, stability, and reliability. Here are some examples: Lowering the vehicle with a nonHonda suspension kit that significantly reduces ground clearance can allow the undercarriage to hit speed bumps or other raised objects, which could cause the airbags to deploy.
Main Menu Table of Contents Carrying Cargo UPPER AND LOWER CONSOLE COMPARTMENTS DOOR POCKETS Your vehicle has several convenient storage areas: Upper and lower console compartments Dashboard lower pocket Door pockets Before Driving Console side net Seat-back pocket Trunk However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, which may make it unsafe. Before carrying any type of cargo, be sure to read the following pages.
Main Menu Table of Contents Carrying Cargo Load Limits The maximum load for your vehicle is 400 lbs (181 kg) for U.S. vehicles, and 185 kg for Canadian vehicles. This figure includes the total weight of all occupants, cargo, and accessories. Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed. Follow all load limits and other loading guidelines in this manual. 118 Steps for Determining Correct Load Limit: 1.
Main Menu Table of Contents Carrying Cargo Carrying Items in the Passenger Compartment Store or secure all items that could be thrown around and hurt someone during a crash. Carrying Cargo in the Trunk Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible.
Main Menu
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the manual transmission. It also includes important information on parking your vehicle and the braking system. Driving Guidelines ......................... 122 Preparing to Drive ......................... 123 Starting the Engine........................ 124 Manual Transmission.................... 125 Parking ............................................ 127 Braking System.......................
Main Menu Table of Contents Driving Guidelines Because of the low-profile tires fitted to your vehicle, the alloy wheels are closer to the ground. Driving over a pothole or road debris at too high a speed can seriously damage a wheel. Slow down under these conditions. Your vehicle is designed to give you optimum handling and performance on well-maintained roads. As part of this design, your vehicle has a minimum of ground clearance and very low-profile tires.
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments before you drive your vehicle. 5. Check that any items you may be carrying are stored properly or fastened down securely. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 6. Check the seat adjustment (see page 67 ). 3. Check that the trunk is fully closed. 8. Make sure the doors are securely closed and locked. 10.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 6. If the engine does not start within 15 seconds, or starts but stalls right away, repeat step 5 with the accelerator pedal pressed halfway down. If the engine starts, release pressure on the accelerator pedal so the engine does not race. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Push the clutch pedal down all the way.
Main Menu Table of Contents Manual Transmission Come to a full stop before you shift into reverse. You can damage the transmission by trying to shift into reverse with the vehicle moving. Push down the clutch pedal, and pause for a few seconds before shifting into reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’ Use extra care when driving on slippery surfaces. Your vehicle is equipped with an aluminum shift lever.
Main Menu Table of Contents Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control.
Main Menu Table of Contents Parking, Braking System Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline. Parking Tips Make sure the convertible top and the windows are closed. Place any packages, valuables, etc., in the trunk or take them with you. Lock the doors. Never park over dry leaves, tall grass, or other flammable materials.
Main Menu Table of Contents Braking System, Anti-lock Brakes (ABS) Check the brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious in your driving. Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.).
Main Menu Table of Contents Anti-lock Brakes (ABS) ABS Indicator ANTI-LOCK BRAKE SYSTEM INDICATOR Important Safety Reminders ABS does not reduce the time or distance it takes to stop the vehicle; it only helps with steering control during braking. A vehicle with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a vehicle without antilock.
Main Menu Table of Contents Vehicle Stability Assist (VSA) System The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.
Main Menu Table of Contents Vehicle Stability Assist (VSA) System, Towing a Trailer Immediately after freeing your vehicle, be sure to switch the VSA on again. We do not recommend driving your vehicle with the VSA and traction control systems switched off. VSA Off Switch This switch is at the left side of the right vent. Press it to turn VSA on and off.
Main Menu
Main Menu Maintenance This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions. This section also includes instructions on how to read the maintenance minder messages on the information display, a maintenance record, and instructions for simple maintenance tasks you may want to take care of yourself.
Main Menu Table of Contents Maintenance Safety All service items not detailed in this section should be performed by a certified technician or other qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required. Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off. To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.
Main Menu Table of Contents Maintenance Minder Your vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer do engine oil replacement and indicated maintenance service. Based on the engine operating conditions and accumulated engine revolutions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.
Main Menu Table of Contents Maintenance Minder MAINTENANCE MINDER INDICATOR The maintenance item code or codes indicate the main and sub items required at the time of the oil change (see page 142 ). ENGINE OIL LIFE INDICATOR MAINTENANCE ITEM CODE(S) If the remaining engine oil life is 15 to 6 percent, you will see the engine oil life indicator every time you turn the ignition switch to the ON (II) position.
Main Menu Table of Contents Maintenance Minder When the remaining engine oil life is 0 percent, the engine oil life indicator will blink. The display comes on every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator ( ) also comes on and remains on in the instrument panel. When you see this message, immediately have the indicated maintenance done by your dealer.
Main Menu Table of Contents Maintenance Minder The maximum total mileage shown is ‘‘−9999.’’ You can change the information display from the engine oil life display to the odometer, the trip meter, or the outside temperature every time you press and release the TRIP button. When the engine oil life is 0 percent or negative mileage, the maintenance minder indicator ( ) remains on even if you change the information display.
Main Menu Table of Contents Maintenance Minder Resetting the Engine Oil Life Indicator Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position. 1. Turn the ignition switch to the ON (II) position. ENGINE OIL LIFE INDICATOR 3. Press the TRIP button for about 10 seconds. The engine oil life indicator and the maintenance item code(s) will blink.
Main Menu Table of Contents Maintenance Minder Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed. Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.
Main Menu Table of Contents Maintenance Minder U.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards. Lights − Check the operation of the headlights, parking lights, taillights, high-mount brake light, and license plate lights monthly. See page 155 . Engine coolant level − Check the radiator reserve tank every time you fill the fuel tank.
Main Menu Table of Contents Maintenance Minder Maintenance Minder Symbol A B ＊1 : Maintenance Main Items Replace engine oil＊1 Replace engine oil and oil filter Inspect front and rear brakes Check parking brake adjustment Inspect these items: Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system＃ Fuel lines and connections＃ If the message ‘‘SERVICE’’ does not appear more than 12 mo
Main Menu Table of Contents Maintenance Record You or the servicing dealer can record all completed maintenance here. When maintenance is performed, record the mileage, circle the coded item(s) completed, and write in any other non-coded items (such as brake fluid replacement) below the codes. Keep the receipts for all work done on your vehicle. Maintenance can also be recorded in your Honda service history booklet.
Main Menu Table of Contents Maintenance Record Maintenance Performed Mileage Signature Mileage Maintenance Performed Signature Date 144 Date mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2 3 4 5 6 mi km A B 1 2
Main Menu Table of Contents Fluid Locations ENGINE OIL FILL CAP WASHER FLUID (Blue cap) CLUTCH FLUID (Gray cap) BRAKE FLUID (Gray cap) ENGINE OIL DIPSTICK (Black handle) Maintenance ENGINE COOLANT RESERVOIR RADIATOR CAP 145
Main Menu Table of Contents Adding Engine Oil Recommended Engine Oil Oil is major contributor to your engine’s performance and longevity. Always use a premium-grade detergent oil displaying the API certification seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. It is highly recommended that you use Honda motor oil in your vehicle for as long as you own it. Unscrew and remove the engine oil fill cap on the valve cover.
Main Menu Table of Contents Adding Engine Oil, Changing the Oil and Filter The oil’s viscosity or weight is provided on the container’s label. Select the oil for your vehicle according to this chart. An oil with a viscosity of 10W-30 is preferred for optimum fuel economy and year-round protection in your vehicle. You may use 5W-40 oil if the temperature in your area goes below 0°F (−20°C). Engine Oil Additives Your vehicle does not require any oil additives.
Main Menu Table of Contents Changing the Oil and Filter 4. Install a new oil filter according to the instructions that come with it. 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (39 N·m , 4.0 kgf·m) 6. Refill the engine with the recommended oil. WASHER OIL DRAIN BOLT 2. Open the hood, and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.
Main Menu Table of Contents Changing the Oil and Filter, Engine Coolant 8. Let the engine run for several minutes, then check the drain bolt and oil filter for leaks. Adding Engine Coolant RESERVE TANK 9. Turn off the engine and let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil. MAX MIN Maintenance Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly.
Main Menu Table of Contents Engine Coolant If the reserve tank is completely empty, you should also check the coolant level in the radiator. 3. The coolant level should be up to the base of the filler neck. Add coolant if it is low. Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment. Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Main Menu Table of Contents Windshield Washers Check the fluid level in the windshield washer reservoir at least monthly during normal use. RESERVOIR CAP Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition them.
Main Menu Table of Contents Manual Transmission Fluid Put a new washer on the filler bolt, then reinstall the filler bolt and tighten it securely. FILLER BOLT CORRECT LEVEL Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt, and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole.
Main Menu Table of Contents Differential Fluid Use an SAE 90 viscosity hypoid gear oil, API service classified GL5 or GL6 only. FILLER BOLT Put a new washer on the filler bolt, then reinstall the filler bolt. Tighten it securely. Tightening torque: 33 lbf·ft (45 N·m , 4.6 kgf·m) CORRECT LEVEL Maintenance Check the fluid level with the differential at normal operating temperature and the vehicle sitting on level ground.
Main Menu Table of Contents Brake and Clutch Fluid Check the brake fluid level in the reservoirs monthly. Replace the brake fluid according to the time recommendation in the maintenance schedule. Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. Using any non-Honda brake fluid can cause corrosion and decrease the life of the system.
Main Menu Table of Contents Lights Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the trunk, readjustment may be required. Adjustment should be done by your dealer or other qualified mechanic. Replacing a Headlight Bulb The low beam headlight bulbs are a type of high voltage discharge tube. High voltage can remain in the circuit even with the light switch off and the key removed.
Main Menu Table of Contents Lights 6. Insert the socket back into the headlight assembly. Make sure the bulb is installed correctly by looking through the headlight lens. The pins on the base of the bulb should fit in the holes in the headlight assembly. Pivot the holddown wire back in place, and clip the end into the slot. 7. Install the rubber seal over the back of the headlight assembly. 1. Open the hood.
Main Menu Table of Contents Lights Replacing Front Turn Signal and Side Marker/Parking Light Bulbs 1. If you are changing the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, then turn off the engine. If you are changing the bulb on the passenger’s side, turn the steering wheel to the left. 3. Pull the inner fender cover back. 4. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise. 5.
Main Menu Table of Contents Lights Replacing a Side Turn Signal Bulb LENS 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 4. Put the bulb holder back into its hole in the lens, and turn it clockwise until it locks. 5. Turn on the lights to make sure the new bulb is working. BULB SOCKET 1. Use a small flat-tipped screwdriver to pry carefully on the back edge of the side turn signal assembly until it pops out of the body. 2.
Main Menu Table of Contents Lights Replacing Rear Bulbs 2. Remove the fasteners from the trunk lining. To remove a fastener, push on the center of the head until it pops in, then pull the fastener out. 4. Determine which bulb is burned out: turn signal or back-up light. 5. Remove the socket by turning it one-quarter turn counterclockwise. 6. Remove the burned out bulb by pulling it straight out of its socket. 3. Pull the lining back. CONTINUED 159 Maintenance 1. Open the trunk.
Main Menu Table of Contents Lights, Cleaning the Seat Belts 7. Install the new bulb into the socket. Cleaning the Seat Belts If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle. 8. Push the socket into the light assembly, and turn it clockwise until it locks. 9. Turn on the lights to make sure the new bulb is working.
Main Menu Table of Contents Floor Mats, Dust and Pollen Filter, Audio Antenna Floor Mats If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat. Audio Antenna Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system. If you remove a floor mat, make sure to re-anchor it when you put it back in your vehicle.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used. To replace a wiper blade: 1. Raise the wiper arm off the windshield. LOCK TAB Do not open the hood when the wiper arms are raised, or you will damage the hood and the wiper arms. 162 2.
Main Menu Table of Contents Wiper Blades, Wheels, Tires BLADE 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Lower the wiper arm down against the windshield. REINFORCEMENT Aluminum alloy wheels have a protective clear-coat that keeps the aluminum from corroding and tarnishing. Cleaning the wheels with harsh chemicals (including some commercial wheel cleaners) or a stiff brush can damage the clear-coat.
Main Menu Table of Contents Tires Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly. We recommend that you visually check your tires every day.
Main Menu Table of Contents Tires Recommended Tire Pressures The following charts show the recommended cold tire pressures for most normal and high-speed driving conditions. Front: Tire Size 215/45R17 87W Cold Tire Pressure 32 psi (220 kPa , 2.2 kgf/cm ) Rear: Cold Tire Pressure 32 psi (220 kPa , 2.2 kgf/cm ) The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm ) For convenience, the recommended cold air pressures and tire sizes are on a label on the driver’s doorjamb.
Main Menu Table of Contents Tires Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life.
Main Menu Table of Contents Tires It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling. The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel speed and may cause the system to activate.
Main Menu Table of Contents Tires Winter Driving Tires marked ‘‘M ＋ S’’ or ‘‘All Season’’ on the sidewall have an allweather tread design suitable for most winter driving conditions. For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions. Snow Tires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as original tires.
Main Menu Table of Contents Checking the Battery Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion. TEST INDICATOR WINDOW If your vehicle’s battery is disconnected, or goes dead, the audio system will disable itself.
Main Menu Table of Contents Checking the Battery If additional battery maintenance is needed, see your dealer or a qualified technician. WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds. Wash your hands after handling. If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (−) cable first, and reconnect it last.
Main Menu Table of Contents Vehicle Storage If you need to park your vehicle for an extended period (more than 1 month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors. Block the rear wheels. If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.
Main Menu
Main Menu Taking Care of the Unexpected This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed. Compact Spare Tire....................... 174 Changing a Flat Tire .....................
Main Menu Table of Contents Compact Spare Tire Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm ) Follow these precautions: INDICATOR LOCATION MARK Never exceed 50 mph (80 km/h). This tire gives a harsher ride and less traction on some road surfaces.
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. The vehicle can easily roll off the jack, seriously injuring anyone underneath. The compact spare tire is smaller than a standard tire, which will affect the vehicle’s handling. Drive cautiously when this spare is mounted on your vehicle. 1.
Main Menu Table of Contents Changing a Flat Tire SPARE TIRE COVER WHEEL NUT WRENCH CLIPS JACKING POINT 4. Remove the three clips holding the spare tire cover by pulling the rings straight back. Remove the spare tire cover. 5. Unscrew the wing bolt, and take the spare tire out of the spare tire shelf. 6. Loosen each wheel nut 1/2 turn with the wheel nut wrench. 176 7. Place the jack under the jacking point nearest the tire you need to change.
Main Menu Table of Contents Changing a Flat Tire BRAKE HUB EXTENSION 9. Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up. 10.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving. CONTINUED 177 Taking Care of the Unexpected 8.
Main Menu Table of Contents Changing a Flat Tire 11.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten the wheel nuts fully. 178 12.Lower the vehicle to the ground, and remove the jack. 13.Tighten the wheel nuts securely in a crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Main Menu Table of Contents Changing a Flat Tire 14.Remove the tool box from the trunk well, and replace the jack, wheel wrench, and extension in the tool box. 15.Place the tool box into the spare tire shelf in the trunk. CLIPS 17.Put the flat tire in the trunk well vertically as shown. Taking Care of the Unexpected 16.Replace the spare tire cover. Secure it with the three clips. Push each clip in securely, and pivot the ring down flat.
Main Menu Table of Contents If the Engine Won’t Start Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you press the ENGINE START button. You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Main Menu Table of Contents If the Engine Won’t Start If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condition of the battery and terminal connections (see page 169 ). You can then try jump starting the vehicle from a booster battery (see page 182 ).
Main Menu Table of Contents Jump Starting Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery. To jump start your vehicle: 1. Open the hood, and check the physical condition of the battery. In very cold weather, check the condition of the electrolyte.
Main Menu Table of Contents Jump Starting, If the Engine Overheats 5. If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle. 6. Start your vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact. Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.
Main Menu Table of Contents If the Engine Overheats Steam and spray from an overheated engine can seriously scald you. Do not open the hood if steam is coming out. 1. Safely pull to the side of the road. Put the transmission in neutral, and set the parking brake. Turn off the all accessories, and turn on the hazard warning indicators. 2. If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood. 3.
Main Menu Table of Contents If the Engine Overheats 7. If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the reading reaches the middle of the temperature gauge or lower before checking the radiator. Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. 9. Start the engine, and set the temperature control dial to maximum heat.
Main Menu Table of Contents Low Oil Pressure Indicator, Charging System Indicator Low Oil Pressure Indicator This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action. 1. Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators.
Main Menu Table of Contents Malfunction Indicator Lamp If this indicator comes on while driving, it means one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage. If you keep driving with the malf unction indicator lamp on, you can damage your vehicle’s emissions controls and engine.
Main Menu Table of Contents Brake System Indicator The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position, and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake. U.S. Canada If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal.
Main Menu Table of Contents Closing the Convertible Top If the electric motor will not close the convertible top, do the following. CONNECTOR 1. Check the fuse for the convertible top motor (see page 190 ). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the convertible top. If the new fuse blows immediately or the convertible top still does not operate, you can close it manually. 4.
Main Menu Table of Contents Fuses The vehicle’s fuses are contained in three fuse boxes. UNDER-HOOD (PRIMARY) UNDER-HOOD (AUXILIARY) INTERIOR KNOB The interior fuse box is underneath the dashboard on the driver’s side. To open it, turn the knob. 190 The primary under-hood fuse box is on the passenger’s side next to the battery. To open it, push the two tabs as shown. The auxiliary under-hood fuse box is on the driver’s side, near the brake fluid reservoir.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages 194 and 195 , or the diagram on the fuse box lid, which fuse or fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works. 2. Remove the cover from the fuse box. FUSE PULLER 3.
Main Menu Table of Contents Fuses BLOWN 5. Look for a blown wire inside the fuse. If it is blown, replace it with one of the spare fuses of the same rating or lower. 192 If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).
Main Menu Table of Contents Fuses If the radio fuse is removed, the audio system will disable itself. The next time you turn on the radio you will see ‘‘CODE’’ (U.S. model) or ‘‘Code’’ (Canadian model) in the frequency display. Use the preset buttons to enter the five-digit code (see page 105 ). If the instrument panel fuse is removed, the clock setting in the instrument panel will be canceled. To reset the time, see page 54 .
Main Menu Table of Contents Fuse Locations INTERIOR FUSE BOX No. Amps. 194 1 7.5 A 2 3 4 5 6 7 8 9 10 11 12 13 15 A 7.5 A 7.5 A 10 A 20 A 7.5 A 15 A 7.5 A − 7.5 A 15 A 10 A Circuits Protected Windshield Wiper, Auto Stop Signal Washer Motor IGP (DBW) IGP (LAF) Accessory Socket Windshield Wiper Turn Signal Light ACG Meter, Backup Lights Not used Engine Start Fuel Pump, SRS SRS No. Amps. 14 15 16 17 18 19 20 21 10 A 15 A 7.5 A 7.5 A 10 A 15 A − 7.5 A 22 23 24 25 26 27 7.
Main Menu Table of Contents Fuse Locations UNDER-HOOD FUSE BOXES: No. Amps. Circuits Protected No. Amps.
Main Menu Table of Contents Emergency Towing, If Your Vehicle Gets Stuck Emergency Towing If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous. If Your Vehicle Gets Stuck If your vehicle gets stuck in sand, mud, or snow, call a towing service to pull it out (see the previous column). To use the towing hook: 1. Remove the cover from the bumper.
Main Menu Table of Contents If Your Vehicle Gets Stuck Taking Care of the Unexpected 4. Screw the towing hook into the extension and tighten it securely by hand. To avoid damage to your vehicle, use the towing hook f or straight, f lat ground towing only. Do not tow at an angle. The tow hook should not be used to tow the vehicle onto a f lat bed. Do not use it as a tie down.
Main Menu
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your vehicle and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Identification Numbers ................. 200 Specifications ................................. 202 DOT Tire Quality Grading (U.S. Vehicles) ....................... 204 Uniform Tire Quality Grading ...................................
Main Menu Table of Contents Identification Numbers Your vehicle has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
Main Menu Table of Contents Identification Numbers The engine number is stamped on the front right corner of the engine block, below the valve cover. TRANSMISSION NUMBER The transmission number is on a label underneath the transmission.
Main Menu Table of Contents Specifications Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating (GVWR) Engine Type Bore x Stroke Displacement Compression ratio Spark plugs Spark Plug Gap 202 162.0 in (4,115 mm) 68.9 in (1,750 mm) 50.6 in (1,285 mm) 94.5 in (2,400 mm) 57.9 in (1,470 mm) 59.4 in (1,510 mm) See the certification label attached to the driver’s doorjamb. Water cooled 4-stroke DOHC VTEC 4-cylinder gasoline engine 3.43 x 3.57 in (87.0 x 90.
Main Menu Table of Contents Specifications Lights Headlights High Low＊ Front turn signal lights Rear turn signal lights Front side marker/ parking lights Back-up lights License plate light Interior light Trunk light Side turn signal lights 12 V 12 V 12 V 12 V 12 V − − − − − 55 W (H1) 35 W 21 W 21 W 5 W(AMBER) 12 V 12 V 12 V 12 V 12 V − − − − − 21 W 5W 5W 5W 5W Lubricant type Fuses Under-hood See page 195 or the fuse box cover.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Main Menu Table of Contents Tire Labeling The tires that came on your vehicle have a number of markings. Those you should be aware of are described below. Tire Size Whenever tires are replaced, they should be replaced with tires of the same size. The following is an example of tire size with an explanation of what each component means. 245/40R17 91W 91 − Load index (a numerical code associated with the maximum load the tire can carry).
Main Menu Table of Contents Emissions Controls The burning of gasoline in your vehicle’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, ignition timing control, and three way catalytic converter. These three systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Main Menu Table of Contents State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the onboard diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Main Menu Warranty and Customer Relations 211 Warranty and Customer Relations Customer Service Information ................................. 212 Warranty Coverages ..................... 213 Reporting Safety Defects (U.S. Vehicles) ........................... 214 Authorized Manuals ......................
Main Menu Table of Contents Customer Service Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The service manager or general manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new vehicle is covered by these warranties: Emissions Control Systems Defects Warranty and Emissions Performance Warranty − these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional. Please read your warranty booklet for exact information. Original Equipment Battery Limited Warranty − this warranty gives up to 100 % credit toward a replacement battery.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc. 214 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The publications shown below can be purchased from Helm Incorporated. You can order in any of three ways: Detach and mail the order form on the right half of this page Call Helm Inc. at 1-800-782-4356 (credit card orders only) Go online at www. helminc. com If you are interested in other years or models, contact Helm Inc. at 1-800-782-4356. Publication Form Number 61S2A07 Form Description Price Each＊ $75.
Main Menu Table of Contents Authorized Manuals NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention the shipment should be sent. For purchases outside U.S.A. please write to the address shown below for a quotation. Ｓ Ｈ Ｉ Ｐ Ｔ Ｏ Customer Name Attention Street Address − No P.O.
Main Menu Index A Back-up Light Replacement ......... 159 Battery Charging System Indicator............................ 46, 186 Jump Starting ............................. 182 Maintenance ............................... 169 Specifications ............................. 203 Before Driving ............................... 109 Belts, Seat ..................................... 8, 16 Beverage Holder .............................. 78 Booster Seats ................................... 38 Brakes ....................
Main Menu Index Changing Oil How to ......................................... 147 When to....................................... 135 Charging System Indicator .... 46, 186 Checklist, Before Driving ............. 123 Child Safety ...................................... 29 Booster Seats ............................... 38 Child Seats .................................... 34 Important Safety Reminders ...... 32 Larger Children ........................... 37 Risk with Airbags ........................
Main Menu Index Specifications ............................. 202 Speed Limiter ............................. 126 Start Button ................................ 124 Starting........................................ 124 Ethanol in Gasoline ....................... 110 Evaporative Emission Controls .... 207 Exhaust Fumes ................................ 41 Expectant Mothers, Use of Seat Belts by ......................................... 14 Fuel ..................................................
Main Menu Index Gross Vehicle Weight Rating (GVWR) .............................. 118, 202 H Halogen Headlight Bulbs.............. 155 Hazard Warning Flashers............... 58 Headlights Aiming ......................................... 155 Daytime Running Lights............. 57 High Beam Indicator ................... 49 Reminder Tone ............................ 57 Replacing Halogen Bulbs ......... 155 Turning on .................................... 57 Heating and Cooling System ..........
Main Menu Index L Label, Certification ........................ 200 Lane Change, Signaling .................. 57 Lap/Shoulder Belts ................... 12, 17 Lights Bulb Replacement ..................... 155 Turn Signal ................................... 57 Load Limits..................................... 118 LOCK (Ignition Key Position) ....... 62 Locks Anti-theft Steering Column ........ 62 Fuel Fill Door ............................. 111 Power Door .................................. 63 Trunk .........
Main Menu Index Pollen Filter .................................... 161 Power Door Locks ........................... 63 Power Socket Location ................... 78 Power Windows ............................... 68 Pregnancy, Using Seat Belts .......... 14 Preparing to Drive ......................... 123 Protecting Adults and Teens.......... 10 Additional Safety Precautions .... 15 Advice for Pregnant Women...... 14 Protecting Children ......................... 29 General Guidelines ......................
Main Menu Index State Emissions Testing ............... 210 Steam Coming from Engine ......... 183 Steering Wheel Anti-theft Column Lock .............. 62 Stereo Sound System ...................... 88 Storing Your Vehicle ..................... 171 Stuck Vehicle ................................. 196 Supplemental Restraint System Servicing ................................... 27 SRS Indicator.......................... 25, 47 System Components.................... 20 Synthetic Oil ..............................
Main Menu Index Transmission Checking Fluid Level, Manual Transmission.......................... 152 Fluid Selection............................ 152 Identification Number............... 201 Shifting the Manual Transmission.......................... 125 Treadwear ...................................... 204 Trip Meter ........................................ 51 Trunk................................................. 63 Emergency Trunk Opener ......... 64 Opening the ..................................
Main Menu Service Information Summary Gasoline: Premium unleaded gasoline, pump octane number of 91 or higher. Fuel Tank Capacity: 13.2 US gal (50 ) Recommended Engine Oil: API premium grade 10W-30 detergent oil (see page 146 ). Oil change capacity (including filter): 5.1 US qt (4.8 ) Manual Transmission Fluid: Honda Manual Transmission Fluid preferred, or an SAE 10W-30 or 10W-40 motor oil as a temporary replacement (see page 152 ). Tire Pressure (measured cold): Front: 32 psi (220 kPa , 2.
