2012 Insight Owner’s Manual (Unlinked) This document does not contain hyperlinks and may be formatted for printing instead of web use. This is due to changes in content and specifications of the vehicle that happen throughout the model year. This manual will be replaced with a hyperlinked version at the end of the model year. © 2011 American Honda Motor Co., Inc.
Owner’s Identification OWNER This owner’s manual should be considered a permanent part of the vehicle and should remain with the vehicle when it is sold. ADDRESS This owner’s manual covers all models of the Insight. You may find descriptions of equipment and features that are not on your particular model. STREET CITY STATE/PROVINCE/TERRITORY ZIP CODE/ POSTAL CODE V. I. N. DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME DEALER NO.
Introduction Congratulations! Your selection of a 2012 Honda Insight was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new vehicle is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your vehicle so you can refer to it at any time. As you read this manual, you will find information that is preceded by a symbol.
Introduction California Proposition 65 Warning WARNING: This product contains or emits chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Event Data Recorders This vehicle is equipped with one or more devices commonly referred to as event data recorders. These devices record front seat belt use, front passenger seat occupancy, airbag deployment data, and the failure of any airbag system component.
A Few Words About Safety Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining your vehicle.
Contents Your Vehicle at a Glance (main controls) ................................................................................................ 3 Driver and Passenger Safety (seat belts, SRS, and child protection) ............................................................. 5 Instruments and Controls (indicators, gauges, multi-information display, dashboard, and steering column) ........ 59 Features (climate control, audio, steering wheel, security, cruise control, and other convenience items) .........
Overview of Contents Contents A convenient reference to the sections in this manual. Your Vehicle at a Glance A quick reference to the main controls in your vehicle. Driver and Passenger Safety Important information about the proper use and care of your vehicle’s seat belts, an overview of the supplemental restraint system, and valuable information on how to protect children with child restraints.
Your Vehicle at a Glance MULTI-INFORMATION DISPLAY (P.72, 75) HAZARD WARNING BUTTON(P.125) NAVIGATION SYSTEM＊2 AUDIO SYSTEM (P.170) Your Vehicle at a Glance INSTRUMENT PANEL INDICATORS (P.62) GAUGES (P.72) DRIVER’S FRONT AIRBAG (P.10) MIRROR CONTROLS (P.147) PASSENGER’S FRONT AIRBAG (P.10) ECON BUTTON (P.127) CLIMATE CONTROL SYSTEM (P.164) DOOR LOCK TAB (P.133) POWER DOOR LOCK MASTER SWITCH (P.133) AUTOMATIC TRANSMISSION (CVT) (P.273) POWER WINDOW SWITCHES (P.149) HOOD RELEASE HANDLE (P.
Your Vehicle at a Glance KM/MILE CHANGE KNOB (P.73) INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB (P.124) HEADLIGHTS/ TURN SIGNALS (P.120) WINDSHIELD WIPERS/WASHERS (P.119) CRUISE CONTROL BUTTONS＊2 (P.224) MULTI-INFORMATION BUTTONS＊2 (P.76) HORN＊1 NAVIGATION SYSTEM＊3/ AUDIO SYSTEM (P.170) REMOTE AUDIO CONTROL BUTTONS＊2 (P.219) PASSENGER AIRBAG OFF INDICATOR (P.35) VEHICLE STABILITY ASSIST (VSA) OFF SWITCH (P.296) REAR WINDOW DEFOGGER/ HEATED MIRROR＊2 (P.
Driver and Passenger Safety Important Safety Precautions .......... 6 Your Vehicle’s Safety Features........ 8 Seat Belts ........................................ 9 Airbags .......................................... 10 Protecting Adults and Teens.......... 12 1. Close and Lock the Doors ...... 12 2. Adjust the Front Seats ............ 14 3. Adjust the Seat-Backs ............. 15 4. Adjust the Head Restraints .... 16 5. Fasten and Position the Seat Belts .............................. 17 6.
Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. 6 Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags are designed to supplement seat belts, not replace them.
Important Safety Precautions Keep Your Vehicle in Safe Condition Having a tire blowout or a mechanical failure can be extremely hazardous. To reduce the possibility of such problems, check your tire pressures and condition frequently, and perform all regularly scheduled maintenance (see page 340 ).
Your Vehicle’s Safety Features (6) (9) (12) (8) (3) Your vehicle is equipped with many features that work together to protect you and your passengers during a crash.
Your Vehicle’s Safety Features Seat Belts Your vehicle is equipped with seat belts in all seating positions. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.) Not wearing a seat belt properly increases the chance of serious injury or death in a crash, even though your vehicle has airbags.
Your Vehicle’s Safety Features Airbags Your vehicle has a supplemental restraint system (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision (see page 28 for more information on how your front airbags work).
Your Vehicle’s Safety Features The most important things you need to know about your airbags are: Airbags offer no protection in rear collisions, or minor frontal or side collisions. The rest of this section gives more detailed information about how you can maximize your safety. Remember, however, that no safety system can prevent all injuries or deaths that can occur in a severe crash, even when seat belts are properly worn and the airbags deploy. Airbags can pose hazards.
Protecting Adults and Teens Introduction The following pages provide instructions on how to properly protect the driver, adult passengers, and teenage children who are large enough and mature enough to drive or ride in the front. See pages 38 − 55 for important guidelines on how to properly protect infants, small children, and larger children who ride in your vehicle. 1.Close and Lock the Doors After everyone has entered the vehicle, be sure the doors and the hatch are closed and locked.
Protecting Adults and Teens Locking the doors and the hatch also helps prevent an outsider from unexpectedly opening a door or the hatch when you come to a stop. When the hatch is not tightly closed, this indicator will come on. When one or more doors or the hatch are not tightly closed, the corresponding indicator for each condition will come on. Your vehicle has the auto door locking/unlocking feature. For more information, see page 108 .
Protecting Adults and Teens 2.Adjust the Front Seats Adjust the driver’s seat as far to the rear as possible while allowing you to maintain full control of the vehicle. Have a front passenger adjust their seat as far to the rear as possible. 14 If you sit too close to the steering wheel or dashboard, you can be seriously injured by an inflating front airbag, or by striking the steering wheel or dashboard.
Protecting Adults and Teens 3.Adjust the Seat-Backs Adjust the seat-back to an upright position, and sit well back in the seat. See page 141 for how to adjust the seat-backs. Adjust the driver’s seat-back to a comfortable, upright position, leaving ample space between your chest and the airbag cover in the center of the steering wheel. Passengers with adjustable seatbacks should also adjust their seatback to a comfortable, upright position.
Protecting Adults and Teens 4.Adjust the Head Restraints Improperly positioning head restraints reduces their effectiveness and you can be seriously injured in a crash. Make sure head restraints are in place and positioned properly before driving. Adjust the driver’s head restraint so the center of the back of your head rests against the center of the restraint. Have passengers adjust their head restraints properly as well. Taller persons should adjust their restraint as high as possible.
Protecting Adults and Teens Improperly positioning the seat belts can cause serious injury or death in a crash. Make sure all seat belts are properly positioned before driving. Position the lap part of the belt as low as possible across your hips, then pull up on the shoulder part of the belt so the lap part fits snugly. This lets your strong pelvic bones take the force of a crash and reduces the chance of internal injuries.
Protecting Adults and Teens RELEASE BUTTONS Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause very serious injuries in a crash. If a seat belt does not seem to work properly, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt. Using a seat The front seats have adjustable seat belt anchors.
Protecting Adults and Teens Advice for Pregnant Women This will reduce the risk of injuries to both you and your unborn child that can be caused by a crash or an inflating front airbag. Sitting improperly or out of position can result in serious injury or death in a crash. Always sit upright, well back in the seat, with your feet on the floor. When driving, remember to sit upright and adjust the seat as far back as possible while allowing full control of the vehicle.
Protecting Adults and Teens Additional Safety Precautions Two people should never use the same seat belt. If they do, they could be very seriously injured in a crash. Do not put any accessories on seat belts. Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can reduce the protective capability of the seat belt and increase the chance of serious injury in a crash. Never let passengers ride in the cargo area or on top of a foldeddown back seat.
Additional Information About Your Seat Belts Seat Belt Indicator The seat belt system includes an indicator on the instrument panel and a beeper to remind you and your front passenger to fasten your seat belts. This system monitors the front seat belts. If you turn the ignition switch to the ON (II) position before your seat belt is fastened, the beeper will sound and the indicator will flash. If your seat belt is not fastened before the beeper stops, the indicator will stop flashing but remain on.
Additional Information About Your Seat Belts If the indicator comes on or the beeper sounds when the driver’s seat belt is latched and there is no front seat passenger and no items on the front seat, something may be interfering with the monitoring system. Look for and remove: Any items under the front passenger’s seat. Any object(s) hanging on the seat or in the seat-back pocket. Any object on the floor that is touching the rear of the seat-back.
Additional Information About Your Seat Belts Automatic Seat Belt Tensioners To deactivate the lockable retractor, unlatch the buckle and let the seat belt fully retract. To refasten the seat belt, pull it out only as far as needed. Allowing a child to play with a seat belt or wrap one around their neck can result in serious injury or death. Instruct children not to play with any seat belt and make sure any unused seat belt a child can reach is buckled, fully retracted, and locked.
Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully, and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the belts retract easily. If a belt does not retract easily, cleaning the belt may correct the problem (see page 333 ). Any belt that is not in good condition or working properly will not provide good protection and should be replaced as soon as possible.
Additional Information About Your Airbags Airbag System Components (9) (8) (2) (11) Driver and Passenger Safety (13) (14) (5) (1) (4) (8) (1) Driver’s Front Airbag (2) Passenger’s Front Airbag (3) (3) Control Unit (4) Front Seat Belt Tensioners (5) (5) Side Airbags (6) Driver’s Seat Position Sensor (6) (7) Front Passenger’s Weight Sensors (8) Front Impact Sensors (10) (9) Passenger Airbag Off Indicator (10) Side Impact Sensors (First) (11) Occupant Position Detection System (OPDS) Sensor (12) Front
Additional Information About Your Airbags Your Airbag System includes: Two SRS (supplemental restraint system) front airbags. The driver’s airbag is stored in the center of the steering wheel; the front passenger’s airbag is stored in the dashboard. Both are marked ‘‘SRS AIRBAG’’ (see page 28 ). Two side airbags, one for the driver and one for a front passenger. The airbags are stored in the outer edges of the seatbacks. Both are marked ‘‘SIDE AIRBAG’’ (see page 32 ).
Additional Information About Your Airbags A sophisticated electronic system that continually monitors and records information about the sensors, the control unit, the airbag activators, the seat belt tensioners, and driver and front passenger seat belt use when the ignition switch is in the ON (II) position. An indicator on the instrument panel that alerts you that the passenger’s side airbag has been turned off (see page 34 ).
Additional Information About Your Airbags How Your Front Airbags Work During a frontal crash, your seat belt restrains your lower body and torso, and the front airbag helps protect your head and chest. Although both airbags normally inflate within a split second of each other, it is possible for only one airbag to deploy. If you ever have a moderate to severe frontal collision, sensors will detect the vehicle’s rapid deceleration.
Additional Information About Your Airbags Dual-Stage, Multiple-Threshold Front Airbags (SRS) Your vehicle is equipped with dualstage, multiple-threshold front airbags (SRS). During a frontal crash severe enough to cause one or both front airbags to deploy, the airbags can inflate at different rates, depending on the severity of the crash, whether or not the seat belts are latched, and/or other factors.
Additional Information About Your Airbags Advanced Airbags Your front airbags are also advanced airbags. The main purpose of this feature is to help prevent airbagcaused injuries to short drivers and children or small-statured adults who ride in front. For both advanced airbags to work properly: Occupants must sit upright and wear their seat belts properly. Do not spill any liquids on or under the seats, cover the sensors, or put any objects or metal items under the front seats.
Additional Information About Your Airbags Be aware that objects placed on the passenger’s seat can also cause the airbag to be turned off. If the weight sensors detect there is no passenger in the front seat, the airbag is automatically turned off. However, the passenger airbag off indicator in this situation will not come on. that would increase or decrease the weight on the front passenger’s seat.
Additional Information About Your Airbags How Your Side Airbags Work Only one airbag will deploy during a side impact. If the impact is on the passenger’s side, the passenger’s side airbag may not deploy if there is no passenger. To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats.
Additional Information About Your Airbags How Your Side Curtain Airbags Work One or both side curtain airbags may inflate in a moderate to severe frontal collision which causes the front airbags to deploy. There will be some delay between the moment the passenger moves into or out of the airbag deployment path and when the indicator comes on or goes off. A front seat passenger should not use a cushion or another object as a backrest. It may prevent the cutoff system from working properly.
Additional Information About Your Airbags How the SRS Indicator Works The SRS indicator alerts you to a potential problem with your airbag system components. U.S. Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly. When you turn the ignition switch to the ON (II) position, this indicator comes on for several seconds then goes off. This tells you the system is working properly.
Additional Information About Your Airbags How the Passenger Airbag Off Indicator Works Canada On vehicle with navigation system This indicator alerts you that the passenger’s front airbag has been shut off because weight sensors detect about 65 lbs (29 kg) or less (the weight of an infant or small child) on the front passenger’s seat. It does not mean there is a problem with the airbag. PASSENGER AIRBAG OFF INDICATOR U.S.
Additional Information About Your Airbags If the indicator comes on with no front seat passenger and no objects on the seat, or with an adult riding there, something may be interfering with the weight sensors. Look for and remove: Any items under the front passenger’s seat. Any object(s) hanging on the seat or in the seat-back pocket. Any object on the floor that is touching the rear of the seat-back. If no obstructions are found, have your vehicle checked by a dealer as soon as possible.
Additional Information About Your Airbags Additional Safety Precautions Do not attempt to deactivate your airbags. Together, airbags and Do not tamper with airbag components or wiring for any reason. Tampering could cause the airbags to deploy, possibly causing very serious injury. driver’s seat position sensor or the front passenger’s weight sensors ineffective.
Protecting Children − General Guidelines All Children Must Be Restrained Each year, many children are injured or killed in vehicle crashes because they are either unrestrained or not properly restrained. In fact, vehicle collisions are the number one cause of the death of children age 12 and under. Children depend on adults to protect them. However, despite their best intentions, many adults do not know how to properly protect child passengers.
Protecting Children − General Guidelines The National Highway Traffic Safety Administration and Transport Canada recommend that all children aged 12 and under be properly restrained in a back seat. Some states have laws restricting where children may ride. Children who ride in back are less likely to be injured by striking interior vehicle parts during a collision or hard braking. Also, children cannot be injured by an inflating front airbag when they ride in the back.
Protecting Children − General Guidelines To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the dashboard (U.S. models) and on the front visors. Please read and follow the instructions on these labels. U.S.
Protecting Children − General Guidelines Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page 52 ). Move the vehicle seat as far to the rear as possible (see page 141 ). If a Child Requires Close Attention Many parents say they prefer to put an infant or a small child in the front passenger seat so they can watch the child, or because the child requires attention.
Protecting Children − General Guidelines Additional Safety Precautions Never hold an infant or child on your lap. If you are not wearing a Make sure any unused seat belt that a child can reach is buckled, the lockable retractor is activated, and the belt is fully retracted and locked. If a child wraps a loose seat belt in a crash, you could be thrown forward and crush the child against the dashboard or a seat-back.
Protecting Infants and Small Children Protecting Infants Do not put a rear-facing child seat in a forward-facing position. If placed facing forward, an infant could be very seriously injured during a frontal collision. Child Seat Type An infant must be properly restrained in a rear-facing, reclining child seat until the child reaches the seat maker’s weight or height limit for the seat, and the child is at least one year old.
Protecting Infants and Small Children In any of these situations, we strongly recommend that you install the child seat directly behind the front passenger’s seat, move the seat as far forward as needed, and leave it unoccupied. Or, you may wish to get a smaller rear-facing child seat. Protecting Small Children Of the different seats available, we recommend those that have a fivepoint harness system as shown.
Protecting Infants and Small Children, Selecting a Child Seat If it is necessary to put a forwardfacing child seat in the front, move the vehicle seat as far to the rear as possible, and be sure the child seat is firmly secured to the vehicle and the child is properly strapped in the seat. Placing a forward-facing child seat in the front seat can result in serious injury or death if the front airbag inflates.
Selecting a Child Seat, Installing a Child Seat Important considerations when selecting a child seat Make sure the child seat meets the following three requirements: The child seat is the correct type and size for the child. The child seat is the correct type for the seating position. The child seat is compliant with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.
Installing a Child Seat 3. Secure the child in the child seat. The following pages provide guidelines on how to properly install a child seat. A forward-facing child seat is used in all examples, but the instructions are the same for a rearfacing child seat. Installing a Child Seat with LATCH Your vehicle is equipped with LATCH (Lower Anchors and Tethers for CHildren) at the outer rear seats.
Installing a Child Seat TETHER STRAP HOOK Rigid type 3. Place the child seat on the vehicle seat, then attach the seat to the lower anchors according to the child seat maker’s instructions. Some LATCH-compatible seats have a rigid-type connector as shown above. 48 Flexible type Other LATCH-compatible seats have a flexible-type connector as shown above. 4. Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit. ANCHOR 5.
Installing a Child Seat If the tether strap is too long and cannot be tightened firmly, find a route where the strap can be tightened securely. 7. Push and pull the child seat forward and from side-to-side to verify that it is secure. Installing a Child Seat with a Lap/ Shoulder Belt When not using the LATCH system, all child seats must be secured to the vehicle with the lap part of a lap/ shoulder belt.
Installing a Child Seat 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor. 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked, and you will need to repeat these steps. 50 4.
Installing a Child Seat Installing a Child Seat with a Tether ANCHORAGE POINTS A child seat with a tether can be installed in any seating position in the back seat, using one of the anchorage points shown above. Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available. Outer Position TETHER STRAP HOOK ANCHOR 1.
Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in a back seat on a booster seat and wear the lap/ shoulder belt. Allowing a child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.
Protecting Larger Children 3. Does the shoulder belt cross between the child’s neck and arm? Using a Booster Seat 5. Will the child be able to stay seated like this for the whole trip? If a child who uses a booster seat must ride in front, move the vehicle seat as far back as possible, and be sure the child is wearing the seat belt properly.
Protecting Larger Children When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in a back seat. If the passenger’s front airbag inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position. Of course, children vary widely.
Protecting Larger Children Additional Safety Precautions Do not let a child wear a seat belt across the neck. This could result Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could improve a child’s comfort or reposition the shoulder part of a seat belt can make the belt less effective and increase the chance of serious injury in a crash. Driver and Passenger Safety in serious neck injuries during a crash. Do not put any accessories on a seat belt.
Carbon Monoxide Hazard Your vehicle’s exhaust contains carbon monoxide gas. Carbon monoxide should not enter the vehicle in normal driving if you maintain your vehicle properly and follow the information on this page. Have the exhaust system inspected for leaks whenever: Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide. The vehicle is raised for an oil change.
Safety Labels DASHBOARD SUN VISORS U.S. models only U.S. models Driver and Passenger Safety These labels are in the locations shown. They warn you of potential hazards that could cause serious injury or death. Read these labels carefully. If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact your dealer for a replacement.
Safety Labels DOORJAMBS U.S.
Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach. Driver’s Seat Height Adjustment ............................. 141 Head Restraints ......................... 142 Folding the Rear Seats Down .. 145 Armrest ....................................... 146 Mirrors ............................................ 147 Adjusting the Power Mirrors ... 147 Power Mirror Heaters.....
Control Locations INSTRUMENT PANEL INDICATORS (P.62) GAUGES (P.72) MULTI-INFORMATION DISPLAY (P.72, 75) MIRROR CONTROLS (P.147) NAVIGATION SYSTEM＊2 AUDIO SYSTEM (P.170) ECON BUTTON (P.127) DOOR LOCK TAB (P.133) PASSENGER AIRBAG OFF INDICATOR (P.35) POWER DOOR LOCK MASTER SWITCH (P.133) CLIMATE CONTROL SYSTEM (P.164) POWER WINDOW SWITCHES (P.149) HOOD RELEASE HANDLE (P.250) PADDLE SHIFTERS＊1 (P.278) EX model with navigation system is shown.
Instrument Panel BRAKE SYSTEM INDICATOR (AMBER) (P.64) VSA OFF INDICATOR (P.65, 295) LIGHTS ON INDICATOR (P.69) ECON MODE INDICATOR (P.71) SECURITY SYSTEM INDICATOR＊ (P.70) LOW OIL PRESSURE INDICATOR (P.62, 415) ＊ : If equipped ELECTRIC POWER STEERING INDICATOR (P.68) DOOR/HATCH OPEN INDICATOR (P.68) IMMOBILIZER SYSTEM INDICATOR (P.63) IMA SYSTEM INDICATOR (P.66) MALFUNCTION INDICATOR LAMP (P.62, 417) 12 VOLT BATTERY CHARGING SYSTEM INDICATOR (P.
Instrument Panel Indicators The instrument panel has many indicators to give you important information about your vehicle. Seat Belt Reminder Indicator This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt. You will also see a ‘‘FASTEN SEAT BELT’’ message on the multiinformation display.
Instrument Panel Indicators Immobilizer System Indicator This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly coded ignition key. If it is not a properly coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page 130 ). Parking Brake and Brake System Indicator (Red) This indicator has two functions: U.S. Canada 1.
Instrument Panel Indicators U.S. Canada Brake System Indicator (Amber) This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and START (III) position. When the brake system indicator (amber) comes on and stays on, there is a problem with the Creep Aid System or Brake Assist (the normal brake operates properly). Have your vehicle checked by your dealer. For more information, see page 287 .
Instrument Panel Indicators U.S. Canada Vehicle Stability Assist (VSA) System Indicator This indicator has two functions: 1. It flashes when VSA is active (see page 295 ). 2. If it comes on and stays on at any other time, there is a problem with the VSA or hill start assist system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page 295 for more information on the VSA system.
Instrument Panel Indicators IMA System Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a problem in the integrated motor assist (IMA) system. With the IMA indicator on, the vehicle may not accelerate as it normally does. Have the vehicle checked by the dealer as soon as possible. You will also see a ‘‘CHECK IMA SYSTEM’’ message on the multiinformation display.
Instrument Panel Indicators Low Temperature Indicator This indicator shows the temperature of the engine coolant. If there is no problem, this indicator comes on when the engine is cold. If it comes on when the engine is warm (normal operating temperature), have the vehicle inspected by your dealer as soon as possible. If the indicator begins to blink or stays on, you will also see a ‘‘WATER TEMP HOT’’ message on the multiinformation display.
Instrument Panel Indicators Electric Power Steering (EPS) Indicator This indicator normally comes on when you turn the ignition switch to the ON (II) position and goes off after the engine starts. If it comes on at any other time, there is a problem in the electric power steering system. If this happens, stop the vehicle in a safe place and turn off the engine. Reset the system by restarting the engine. The indicator will stay on, but should go off after driving a short distance.
Instrument Panel Indicators When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash. Lights On Indicator This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the or position. If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on.
Instrument Panel Indicators Low Fuel Indicator LOW FUEL INDICATOR This indicator is in the fuel gauge. It comes on as a reminder that you must refuel soon. You will also see a ‘‘FUEL LOW’’ message on the multiinformation display. When the indicator comes on, there are about 1.8 U.S. gal (6.9 ) of fuel remaining in the tank. When the needle reaches E, there is a very small amount of fuel in the tank.
Instrument Panel Indicators ECON Mode Indicator Instruments and Controls This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. When you turn the econ mode on by pressing the ECON button with the ignition switch in the ON (II) position, this indicator will come on. You will also see the symbol on the multi-information display with ECON ON or ECON OFF (see page 75 ).
Gauges Speedometer/Ambient Meter This shows your speed in kilometers per hour (km/h) or miles per hour (mph) depending on the selected speedometer display. You can switch the display between km/h and mph (see page 73 ). SPEEDOMETER/AMBIENT METER CHARGE/ASSIST GAUGE TACHOMETER FUEL GAUGE The speedometer also has an ambient meter. The color of the ambient meter changes automatically according to your driving style (see page 268 ). You can customize the setting of the ambient meter (see page 103 ).
Gauges Sel/Reset Knob To switch the lower segment of the multi-information display between the odometer with the outside temperature and trip meter with the outside temperature, press the sel/ reset knob repeatedly. For more information, see page 78 . KM/MILE CHANGE KNOB Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition. Avoid driving with an extremely low f uel level.
Gauges Charge/Assist Gauge IMA ASSIST GAUGE IMA CHARGE GAUGE This gauge shows you the charge/ discharge status of the Integrated Motor Assist (IMA). When the IMA is assisting the engine, the pointer stays in the assist gauge (upper part of the gauge). When the IMA battery is being charged, the pointer stays in the charge gauge (lower part of the gauge). 74 You can also check the status of the IMA system function on the multiinformation display (see page 84 ).
Multi-Information Display There are three types of messages: normal display messages, engine oil life and maintenance messages, and system messages. You can select the displayed language and also customize some vehicle control settings to your liking with the multi-information display and the three buttons on the steering wheel (see page 76 ). Normal Display Messages ECON is On. ECON is Off.
Multi-Information Display U.S. model is shown. The multi-information display changes to the blank display shown above several seconds after you turn the ignition switch to the ON (II) position. 76 INFO BUTTONS (▲/▼) SEL/RESET BUTTON SEL/RESET BUTTON LX and EX models INFO (▲/▼) BUTTON Insight model With the ignition switch in the ON (II) position, the multi-information display changes as shown on page 78 each time you press the INFO (▲/▼) button or SEL/RESET button.
Multi-Information Display In the multi-information display, the system message is also displayed (see page 88 ) and you can customize your vehicle control settings (see page 91 ). MIDDLE SEGMENT LOWER SEGMENT The multi-information display consists of an upper segment, a middle segment and a lower segment. CONTINUED 77 Instruments and Controls U.S. model is shown.
Multi-Information Display HFL＊ (See page 87) Eco Guide Feedback Average Fuel Monitor Economy Record (See page 81) (See page 81) Trip Computer (See page 81) Engine Oil Life (See page 80) Outside Temperature (See page 80) : Press the INFO button ▼. : Press the INFO button ▲. : Press the SEL/RESET button. U.S. model is shown. 78 ＊ : This display will be shown when the Bluetooth HandsFreeLink is activated.
Multi-Information Display Odometer U.S. Trip Meter Canada TRIP METER A TRIP METER B When you reset Trip A, average fuel economy A is reset at the same time. When you reset Trip B, average fuel economy B is reset. ODOMETER The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S.
Multi-Information Display Outside Temperature U.S. Canada OUTSIDE TEMPERATURE This shows the outside Fahrenheit temperature in U.S. models, and Celsius temperature in Canadian models. The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h).
Multi-Information Display Eco Guide Feedback Monitor ECO-DRIVE SCORE DISPLAY Average Fuel Economy Records U.S. Canada ACCELERATION MONITOR U.S. model is shown. Eco guide feedback monitor consists of three parts. The eco-drive score display shows the accumulated eco score for one driving cycle. The acceleration monitor shows acceleration efficiency. The deceleration monitor shows deceleration efficiency. See page 267 for more information.
Multi-Information Display Instant Fuel Economy Average Fuel Economy A/B U.S. U.S. Canada AVERAGE FUEL ECONOMY A INSTANT FUEL ECONOMY Canada AVERAGE FUEL ECONOMY B Mile indication (U.S. models) Average Fuel Economy A : This shows your vehicle’s instant fuel economy in mpg. Kilometer indication (Canadian models) : This shows your vehicle’s average fuel economy in mpg (U.S. models) or l/100 km (Canadian models) since you last reset trip computer A.
Multi-Information Display ELAPSED TIME AVG. SPEED This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset. This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models. If you want to reset the ELAPSED TIME manually, go to the trip computer’s ELAPSED TIME display, and press and hold the SEL/RESET button until the number resets.
Multi-Information Display IMA System Power Flow Monitor POWER FLOW ENGINE OPERATION ICON IMA BATTERY/BATTERY LEVEL INDICATOR The IMA system power flow monitor shows the status of the IMA system. The energy source, and powering status of the engine and IMA motor (engine operation icon and IMA battery) are represented by arrows on the display The battery level indicator shows the state of charge of the IMA battery.
Multi-Information Display IMA Battery Level Indicator IMA BATTERY LEVEL INDICATOR Level 0 Level 1 Level 2 Level 3 Level 5 Level 6 Highest level of state of charge LEVEL READING The IMA battery level indicator shows you the state of charge of the battery for the Integrated Motor Assist (IMA). This battery is recharged and discharged by the IMA motor depending on the driving conditions. The position of the battery level reading shows the state of charge of the IMA battery.
Multi-Information Display On vehicle with paddle shifters The IMA battery is charged at a higher rate when the transmission is in L (Low) mode (see page 282 ). On vehicle without paddle shifters The IMA battery is charged at a higher rate when the transmission is in LOW (L) range (see page 276 ). If the battery is mostly discharged, the auto idle stop function is disabled (see page 283 ). The battery level gauge does not read the battery level directly.
Multi-Information Display Bluetooth HandsFreeLink Instruments and Controls To use the system, your cell phone and the HFL system must be linked. Not all cell phones are compatible with this system. Refer to page 227 for instructions on how to link your cell phone to HFL and how to receive or make phone calls, or visit the handsfreelink.com website. In Canada, visit www.handsfreelink.ca, or call (888) 528-7876.
Multi-Information Display System Messages SYSTEM MESSAGE INDICATOR The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected. You will also hear a beep when the system message comes on for the first time.
Multi-Information Display See page 12 U.S. Canada See page 368 See page 13 See page 367 See page 13 See page 151 See page 366 See page 21 See page 321 See page 289 See page 21 U.S.
Multi-Information Display See page 70 See page 123 See page 68 See page 302 See page 291 See page 131 See page 303 See page 292 See page 131 See page 304 See page 362 See page 132 See page 249 See page 319 See page 80 See page 295 U.S. only U.S.
Multi-Information Display Customized Settings If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position, or move the shift lever out of Park, the display will change to the normal screen. Refer to the table on the following pages about the settings you want to customize. You can customize some vehicle control settings. To enter the customizing mode, press and hold either INFO button (▲/▼) for more than 3 seconds.
Multi-Information Display Group Setup METER SETUP (P.96) LIGHTING SETUP (P.104) ＊: 92 Default setting Menu Item LANGUAGE SELECTION Description Changes the language used in the display. ADJUST OUTSIDE TEMP. DISPLAY Changes the outside temperature reading above or below its current reading. TRIP A RESET with REFUEL ELAPSED TIME RESET Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.
Multi-Information Display Group Setup DOOR SETUP (P.108) Menu Item AUTO DOOR LOCK AUTO DOOR UNLOCK KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER DEFAULT ALL (P.117) ＊: Changes when the doors automatically unlock. Changes which doors unlock with the remote transmitter in a first push. The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice.
Multi-Information Display Each time you press the INFO (▲/ ▼) button, the screen changes as shown on the next page. Press the INFO (▲/▼) button until you see the setup you want to customize, then press the SEL/RESET button to enter your selection. Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize: METER SETUP LIGHTING SETUP DOOR SETUP If you do not make any changes, select ‘‘EXIT.
Multi-Information Display NORMAL DISPLAY U.S. Instruments and Controls METER SETUP See page 96 Canada LIGHTING SETUP See page 104 DOOR SETUP See page 108 : Press and hold the INFO (▲/▼) button. : Press the SEL/RESET button. : Press the INFO button ▼. : Press the INFO button ▲.
Multi-Information Display Meter Setup Here are the four custom settings for the meter setup: LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY TRIP A RESET with REFUEL ELAPSED TIME RESET DISPLAY KM/MILES METER COLOR CHANGE See page 97 See page 98 See page 99 See page 100 While ‘‘METER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO (▲/ ▼) button, the screen changes as shown in the illustration.
Multi-Information Display Language Selection You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to see the selections. Select the desired language by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen.
Multi-Information Display Adjust Outside Temp. Display U.S. models If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions: You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to enter the setting. 98 Canadian models Adjust the outside temperature value by pressing the INFO (▲/▼) button repeatedly.
Multi-Information Display Trip A Reset With Refuel You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/ RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen.
Multi-Information Display Elapsed Time Reset There are three elapsed time reset choices you can make: IGN OFF − The elapsed time is reset when you turn the ignition switch to the LOCK (0) position. TRIP A − The elapsed time is reset when Trip A is reset. TRIP B − The elapsed time is reset when Trip B is reset. You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. 100 Press the SEL/RESET button to see the selections.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ELAPSED TIME RESET’’ and repeat the procedure again. To change the displayed measurement in the trip computer and trip information and to switch between kilometers and miles, follow these instructions: You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly.
Multi-Information Display AUTO: When you press the km/mile change knob in the instrument panel to switch the speedometer reading between miles per hour (mph) and kilometers per hour (km/h), the displayed measurement in the trip computer and trip information, also switches to kilometers or miles depending on the selected speedometer reading. KM: The displayed measurement in the trip computer and trip information is set to kilometers. Press the SEL/RESET button to see the selections.
Multi-Information Display Meter Color Change Press the SEL/RESET button to see the selections. You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Select ON or OFF by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/ RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen.
Multi-Information Display Lighting Setup There is one custom setting for the lighting setup: See page 105 INTERIOR LIGHT DIMMING TIME AUTO LIGHT SENSITIVITY While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO (▲/ ▼) button, the screen changes as shown in the illustration. Press the INFO (▲/▼) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
Multi-Information Display Interior Light Dimming Time You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO (▲/ ▼) button repeatedly. Press the SEL/RESET button to see the selections. Select the desired setting (15sec, 30sec, or 60sec) by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/ RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen.
Multi-Information Display Auto Light Sensitivity The headlights automatically come on when the headlight switch is in the AUTO position and the ambient light reaches a changeable level. You can select the auto light sensitivity from the following five levels: MAX − The headlights come on when it is bright. HIGH − The headlights come on when it is somewhat bright. MID − The headlights come on when it is as bright as sunset or sunrise. LOW − The headlights come on when it is somewhat dark.
Multi-Information Display Instruments and Controls When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO LIGHT SENSITIVITY’’ and repeat the procedure again.
Multi-Information Display Door Setup Here are the five custom settings for the door setup: AUTO DOOR LOCK AUTO DOOR UNLOCK DOOR LOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER See page 109 See page 110 See page 112 While ‘‘DOOR SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO (▲/ ▼) button, the screen changes as shown in the illustration.
Multi-Information Display Auto Door Lock There are three settings you can choose from: Instruments and Controls SHIFT FROM P − The doors lock whenever you move the shift lever out of Park. WITH VEHICLE SPEED − The doors lock when the vehicle speed reaches about 10 mph (about 16 km/h). OFF − The auto door lock mode is deactivated all the time. You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to enter the selecting mode.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again. Auto Door Unlock There are five possible settings you can choose from: DRIVER DOOR WITH SHIFT TO P − The driver’s door unlocks when you move the shift lever to Park with the brake pedal depressed. ALL DOORS WITH SHIFT TO P − All the doors unlock when you move the shift lever to Park with the brake pedal depressed.
Multi-Information Display DRIVER DOOR WITH IGN OFF − The driver’s door unlocks when you turn the ignition switch to the LOCK (0) position. Instruments and Controls ALL DOORS WITH IGN OFF − All the doors unlock when you turn the ignition switch to the LOCK (0) position. OFF − The auto door unlock is deactivated all the time. You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to enter the selecting mode.
Multi-Information Display Door Lock Mode If you choose ‘‘ALL DOORS With IGN OFF,’’ you will see the above display. Press the SEL/RESET button to enter your selection. 112 When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘DOOR LOCK MODE’’ and repeat the procedure again. Select the desired setting by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. Instruments and Controls Press the SEL/RESET button to enter the selecting mode. When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen.
Multi-Information Display Keyless Lock Acknowledgment When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the hatch are locked and the security system has set (see page 223 ). You can customize the exterior lights not to flash and the beeper not to sound. You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO (▲/▼) button repeatedly.
Multi-Information Display Security Relock Timer You can change this relock time from 30 seconds to 60 or 90 seconds. When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen. You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO (▲/▼) button repeatedly. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again. Press the SEL/RESET button to enter the selecting mode. Select the desired setting by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. 116 When your selection is successfully completed, the display changes as shown above, and then goes back to the customizable item screen.
Multi-Information Display DEFAULT ALL To set the default settings, press the INFO (▲/▼) button to select SET then press the SEL/RESET button. If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display. When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to the default all setting display.
Controls Near the Steering Wheel INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB (P.124) WINDSHIELD WIPERS/WASHERS (P.119) CRUISE CONTROL BUTTONS＊2 (P.224) MULTI-INFORMATION BUTTONS＊2 (P.76) HEADLIGHTS/TURN SIGNALS (P.120) MIRROR CONTROLS (P.147) NAVIGATION SYSTEM＊3/ AUDIO SYSTEM (P.170) REMOTE AUDIO CONTROL BUTTONS＊2 (P.219) REAR WINDOW DEFOGGER/ HEATED MIRROR＊2 (P.126/148) VEHICLE STABILITY ASSIST (VSA) OFF SWITCH (P.296) ACCESSORY POWER SOCKET (P.
Windshield Wipers and Washers Push the right lever up or down to select a position. LO − The wipers run at low speed. HI − The wipers run at high speed. MIST − The wipers run at high speed until you release the lever. ADJUSTMENT RING INT − The length of the wipe interval is varied automatically according to vehicle’s speed. EX model is shown. EX models 1. MIST 2. OFF 3. INT − Intermittent 4. LO − Low speed 5. HI − High speed 6.
Windshield Wipers and Washers, Turn Signals and Headlights Rear Window Wiper and Washer 4. Rotate the switch counterclockwise also to spray the window washer and turn the wiper on. Turn Signals and Headlights When you shift the transmission to the reverse position with the front windshield wiper activated, the rear wiper operates automatically even if the rear wiper switch is off. The rear window washer uses the same fluid reservoir as the windshield washer. 1.
Turn Signals and Headlights Headlights − Turning the switch to the ‘‘ ’’ position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. High Beams − Push the left lever forward until you hear a click. The blue high beam indicator will come on (see page 69 ). Pull the lever back to return to the low beams. Turning the switch to the ‘‘ ’’ position turns on the headlights. To flash the high beams, pull the lever back lightly, then release it.
Headlights On EX models AUTO − The automatic lighting feature turns on the headlights, all other exterior lights, and the instrument panel lights when it senses low ambient light. To turn on the automatic lighting, turn the light switch to the AUTO position. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator turn off automatically when the system senses high ambient light.
Headlights The headlights revert to normal operation when you turn them on with the switch. Instruments and Controls Daytime Running Lights With the headlight switch off or in the position, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
Instrument Panel Brightness To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the or position. Turning the knob to the right until you hear a tone will cancel the reduced brightness. INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness with the ignition switch in the ON (II) position and the parking lights on.
Instrument Panel Brightness, Hazard Warning Button If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door. Hazard Warning Button HAZARD WARNING BUTTON Instruments and Controls If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds. Push the button next to the audio system to turn on the hazard warning lights (four-way flashers).
Rear Window Defogger The defogger will shut itself off within about 10 to 30 minutes according to the outside temperature (over 32°F, 0°C). Make sure all rear windows are clear and you have good visibility before starting to drive. U.S. EX model is shown. The rear window defogger will clear fog, frost, and thin ice from the windows. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. It also shuts off when you turn off the ignition switch.
ECON Button ECON MODE INDICATOR When you turn off and then restart the engine, the ECON mode setting remains the same as previously set. ECON BUTTON The ECON button turns the ECON mode on and off. The ECON mode helps you improve your fuel economy by modifying some vehicle functions.
Steering Wheel Adjustments Make any steering wheel adjustments before you start driving. Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash. Adjust the steering wheel only when the vehicle is stopped. 3. Push the lever forward fully to lock the steering wheel in position. Make sure the lever is positioned securely at the bottom of the steering column as shown. To adjust To lock LEVER 1.
Keys and Locks KEY NUMBER TAG IGNITION KEYS WITH REMOTE TRANSMITTER You should have received a key number tag with your keys. You will need this number if you ever have to get a lost key replaced. Use only Honda-approved key blanks. These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged. Do not drop the keys or set heavy objects on them. Two ignition keys come with your vehicle.
Immobilizer System The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine’s fuel system is disabled. When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key.
Ignition Switch LOCK (0) − You can insert or remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly. The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). If you leave the key in the ignition switch in the ACCESSORY (I) position and open the driver’s door, you will see a ‘‘RETURN IGNITION SWITCH TO LOCK (0) POSITION’’ message on the multi-information display and hear a reminder beeper.
Ignition Switch ON (II) − This is the normal key position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position. START (III) − Use this position only to start the engine. The switch returns to the ON (II) position when you let go of the key. You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door.
Door Locks MASTER DOOR LOCK SWITCH Lock LOCK TAB To unlock To lock To lock all doors and the hatch, push the front of the master door lock switch on the driver’s door, pull the lock tab rearward on the driver’s door, or use the key on the outside lock on the driver’s door. You can customize the door lock/ unlock settings (see page 108 ). The lock tab on each passenger’s door locks and unlocks that door.
Door Locks To lock any passenger’s door when getting out of the vehicle, pull the lock tab rearward and close the door. To lock the driver’s door, remove the key from the ignition switch, pull the lock tab rearward or push the front of the master switch, then close the door. Default setting When the vehicle speed reaches about 10 mph (U.S.)/15 km/h (Canada) or more, all the doors and the hatch lock automatically. When you shift to P after driving, the driver’s door unlocks.
Remote Transmitter LED PANIC BUTTON LOCK − Press this button once to lock all doors and the hatch. Some exterior lights will flash once. When you press LOCK twice within 5 seconds, the horn will sounds to verify that the doors are locked. You cannot lock the doors if any door or the hatch is not fully closed or if the key is in the ignition switch. On LX and EX models If you press the LOCK button twice within 5 seconds, you will hear a horn to verify that the security system has set.
Remote Transmitter PANIC − Press and hold this button for about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch. Remote Transmitter Care Avoid dropping or throwing the transmitter. Protect the transmitter from extreme temperatures.
Remote Transmitter COIN KEYPAD SCREW To replace the battery: 1. Remove the screw at the base of the transmitter with a small Phillips-head screwdriver. NOTE: Be careful when removing this screw as the head of the screw can strip out. 3. Place a cloth on the edge of the keypad to prevent scratches, and remove the upper half by carefully prying on the edge with a coin. 4. Remove the old battery and note the polarity.
Remote Transmitter An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal. As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Hatch The hatch will lock or unlock when you lock/unlock the driver’s door with the key, the remote transmitter, the master door lock switch, or the lock tab on the driver’s door. RELEASE To open the hatch, push the release, and lift up. To close the hatch, use the handle to lower it, then press down on the back edge. Keep the hatch closed at all times while driving to avoid damaging the hatch and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 56 .
Hatch Unlocking the Hatch COVER Unlock RELEASE LEVER If the power door lock system cannot unlock the hatch, unlock it manually. Place a cloth on the top side of the cover to prevent scratches, then use a small flat-tip screwdriver to remove the cover on the back of the hatch. 140 Push the release lever to the lower left as shown, and push the hatch to open it. If you need to unlock the hatch manually, it means there is a problem with the hatch. Have the vehicle checked by your dealer.
Seats Front Seat Adjustments Driver’s Seat Height Adjustment See pages 14 − 15 for important safety information and warnings about how to properly position seats and seat-backs. To change the seat-back angle of the front seat, pull up the lever on the outside of the seat bottom. To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and release the bar. Try to move the seat to make sure it is locked in position.
Seats Head Restraints Front Position See page 16 for important safety information and a warning about improperly positioning head restraints. CUSHION Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from the likelihood of whiplash and other injuries. RELEASE BUTTON LEGS They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint.
Seats Removing the Head Restraint Rear Center Position CUSHION Rear Outer Position CUSHION For Rear Seat Head Restraints LEGS SEAT-BACK RELEASE BUTTON RELEASE BUTTON LEGS SEAT-BACK The seat-back must be folded forward (see page 145 ) to get ceiling clearance for removal of the head restraints. When a passenger is seated in the rear center seating position, the center head restraint should be adjusted up or down, to match the passenger’s height.
Seats Active Head Restraints Failure to reinstall, or correctly reinstall, the head restraints can result in severe injury during a crash. After a collision, the activated restraint should return to its normal position. Always replace the head restraints before driving. When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button. Make sure the head restraint locks in position when you reinstall it.
Seats For a head restraint system to work properly: Do not place any object between an occupant and the seat-back. Install each restraint in its proper location. Only use genuine Honda replacement head restraints. RED INDICATOR Each side folds down separately, so you can still carry one or two passengers in the rear seat. Remove any items from the seat before folding down the seat-back, and make sure there are no items on the floor before folding down the seats. 1.
Seats Reverse this procedure to return the seat-back to the upright position. Pull on the seat-back to make sure it is latched. If the seat-back is not latched fully, the seat belt will not work properly and you will see the red indicator behind the release lever as shown on the previous page. Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have to brake hard (See Carrying Cargo on page 258 ).
Mirrors Adjusting the Power Mirrors UP DOWN Daytime Position ADJUSTMENT SWITCH 4. When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings. Night Position Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. The inside mirror has day and night positions. The night position reduces glare from headlights behind you.
Mirrors Power Mirror Heaters HEATED MIRROR BUTTON On U.S. EX models and all Canadian models The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the rear window defogger button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters and the defogger off. 148 This heated mirror function has a timer (see page 126 ).
Power Windows MAIN SWITCH Closing a power window on someone’s hands or fingers can cause serious injury. DRIVER’S WINDOW SWITCH FRONT PASSENGER’S WINDOW SWITCH Turn the ignition switch to the ON (II) position to raise or lower any window. To open a window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.
Power Windows When you push the main switch in, the indicator comes on and the passengers’ windows cannot be raised or lowered. Use the main switch when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally. To cancel this feature, push on the switch again. The switch will pop out. The windows and the main switch feature will operate for up to 10 minutes after you turn off the ignition switch. Opening either front door cancels this function.
Parking Brake PARKING BRAKE LEVER Instruments and Controls EX model is shown. If you drive without releasing the parking brake, a beeper will sound, and you will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display. Driving the vehicle with the parking brake applied can damage the rear brakes and hubs. A beeper will sound if the vehicle is put into gear with the parking brake on. To apply the parking brake, pull the lever up fully.
Interior Convenience Items COAT HOOK REAR DOOR BEVERAGE HOLDER USB ADAPTER CABLE＊ VANITY MIRROR＊ FRONT DOOR POCKET SUN VISOR CENTER POCKET CARGO AREA COVER＊ GLOVE BOX FLOOR STORAGE COMPARTMENT CARGO AREA UNDER FLOOR STORAGES ＊: If equipped EX model with navigation system is shown.
Interior Convenience Items To retract the cover, slip the rods out of the hooks and guide the cover so it rolls back fully into its housing. Cargo Area Cover HANDLE On Canadian EX model only You can use the cargo area cover to conceal your parcels and protect them from direct sunlight. MOUNTING ROD To extend the cargo area cover, pull out the cover from the housing by pulling the handle on the cover’s leading edge, then clip the mounting rods in the slots at both sides of the hatch opening.
Interior Convenience Items To reinstall the cargo area cover housing unit, place one end of the unit in the holder on the side panel, then push it into the side panel slightly and insert the other end into its holder. Push HOUSING UNIT The cargo area cover housing unit can be removed to give you more cargo space. Storing the Cargo Area Cover CARGO AREA COVER LID Make sure the housing unit is securely placed so it will not come loose while you are driving.
Interior Convenience Items Under Floor Storages CARGO AREA COVER STORAGES CARGO FLOOR Floor Storage Compartments STRAP 3. Store the cover in its holders as shown in the illustration above. 4. Reinstall the cargo floor lid. To open the cargo floor, fold the cargo floor forward. To use the storage compartment located on the left side of the cargo area floor, hold the strap and raise the lid. Close the lid by pressing until it latches.
Interior Convenience Items Beverage Holders FRONT FRONT BEVERAGE HOLDERS BEVERAGE HOLDERS EX model Insight model and LX model Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Liquid can also spill from the front and rear door pocket beverage holders when you open or close the doors. Use only resealable containers in the door pockets. Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.
Interior Convenience Items Accessory Power Socket It will not power an automotive type cigarette lighter element. Console Compartment Instruments and Controls Make sure to put the socket cover back in place to prevent any small foreign objects from getting into the socket. LEVER Your vehicle has an accessory power socket in the front console panel. To use an accessory power socket, the ignition switch must be in the ACCESSORY (I) or ON (II) position. On EX and U.S.
Interior Convenience Items Glove Box Center Tray An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. PARTITION Always keep the glove box closed while driving. Open the glove box by pulling the handle to the left. Close it with a firm push. There is a tray in the front of the center console. You can also take the partition out to extend the tray.
Interior Convenience Items Center Pockets KNOB Instruments and Controls Push LID On EX models On all models To open the center pocket, press the release button. The lid will unlatch and swing up. To close it, push the lid down until it latches. To open the center pocket, push on the knob. To close it, push the lid up until it latches.
Interior Convenience Items Coat Hook Sun Visors Vanity Mirror COAT HOOK EX model is shown. To use a coat hook, slide it out slightly, then pull it down. Make sure the coat hook is pulled up when you are not using it. This hook is not designed for large or heavy items. 160 To use the sun visor, pull it down. You can also use the sun visor at the side window. Remove the support rod from the clip and swing the sun visor toward the side window.
Interior Lights Ceiling Light DOOR ACTIVATED POSITION After all doors are closed tightly, the light dims slightly, then fades out in about 30 seconds. To change the ‘‘INTERIOR LIGHT DIMMING TIME’’ setting, see page 105 . The ceiling light has a three-position switch: ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you: If you leave any door open without the key in the ignition switch, the ceiling light will go off after about 15 minutes.
Interior Lights Cargo Area Light SPOTLIGHTS Push Push U.S. LX model CARGO AREA LIGHT Your vehicle has a cargo area light on the left side panel of the cargo area. It comes on when you open the hatch.
Features The climate control system in your vehicle provides a comfortable driving environment in all weather conditions. Your vehicle has an anti-theft audio system that requires a code number to enable it. The security system helps to discourage vandalism and theft of your vehicle. Insight model Playing the AM/FM Radio ........... 171 Playing a Disc ................................. 175 Disc Player Error Messages ........ 182 LX model and EX model without navigation system Playing the FM/AM Radio ....
Climate Control System FAN CONTROL BAR AIR CONDITIONING BUTTON MODE CONTROL BUTTON TEMPERATURE CONTROL DIAL FRESH AIR BUTTON RECIRCULATION BUTTON REAR WINDOW DEFOGGER/ HEATED MIRRORS BUTTON WINDSHIELD DEFROST BUTTON U.S.
Climate Control System Voice Control System On models with navigation system The climate control system for your vehicle can also be operated using the voice control system. See the navigation system manual for complete details. Using Automatic Climate Control The automatic climate control system in your vehicle maintains the interior temperature you select. The system also adjusts the fan speed and airflow levels. Temperature Control Turning this dial clockwise increases the temperature of the airflow.
Climate Control System When you set the temperature to its lower limit ( ) or its upper limit ( ), the system runs at full cooling or heating only. It does not regulate the interior temperature. When you adjust a fan control, the fan is taken out of AUTO mode. ON/OFF Button Each time you press this button, the climate control system switches between on and off. Turning on the system with this button selects your last climate control selection.
Climate Control System Air Conditioning (A/C) Button Recirculation Button Rear Window Defogger Button This button turns the air conditioning on and off. You will see A/C ON or A/C OFF in the display. When the recirculation indicator is on, air from the vehicle’s interior is sent throughout the system again. This button turns the rear window defogger on and off (see page 126 ).
Climate Control System To remove fog from the inside of the windows, set as follows: Mode Control Windshield Defroster Button Use the mode control button to select the vents the air flows from. Some air will flow from the dashboard vents in all modes. This button directs the main airflow to the windshield for faster defrosting. It also overrides any mode selection you may have made. Airflow is divided between the floor and corner vents and the defroster vents at the base of the windshield.
Climate Control System Sunlight, Temperature, and Humidity Sensors Features SUNLIGHT SENSOR Insight model and LX model EX models SUNLIGHT SENSOR TEMPERATURE/HUMIDITY SENSOR To regulate the interior temperature and humidity, the climate control system has two sensors. A sunlight sensor is located in the top of the dashboard and a temperature/ humidity sensor is next to the steering column. Do not cover the sensors or spill any liquid on them.
Audio System An audio system is standard on all models. Read the appropriate pages (as shown below) to use your vehicle’s audio system. For Insight model, see pages 171 through 182 . For LX and EX models without navigation system, see pages 183 through 213 . For EX model with navigation system, see navigation system manual for how to operate the audio system.
Playing the AM/FM Radio (Insight model) AM FM BUTTON BUTTON Features POWER/ VOLUME KNOB TUNE KNOB A.
Playing the AM/FM Radio (Insight model) To Play the AM/FM Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the power/volume knob or the AM or FM button. Adjust the volume by turning the power/volume knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM or FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Playing the AM/FM Radio (Insight model) Preset − Each preset button can store one frequency on AM and two frequencies on FM. 2. Use the tune, seek, or scan function to tune the radio to a desired station. 3. Pick a preset button (1−6), then press and hold it until you hear a beep. 4. Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM. Press the left side of the A. SEL/SCAN bar. You will see A.
Playing the AM/FM Radio (Insight model) Adjusting the Sound Press the SOUND (TUNE) knob repeatedly to display the BASS, TREBLE, FADER, BALANCE, and SVC (speed-sensitive volume compensation) settings. SVC − Adjusts the volume level based on the vehicle speed. Speed-sensitive Volume Compensation (SVC) Each mode is shown in the display as it changes. Turn the TUNE knob to adjust the setting to your liking. The SVC mode controls the volume based on vehicle speed.
Playing a Disc (Insight model) CD/AUX BUTTON EJECT BUTTON RANDOM BUTTON REPEAT BUTTON Features LOAD INDICATOR POWER/VOLUME KNOB TUNE KNOB A.
Playing a Disc (Insight model) To Play a Disc To load or play a disc, the ignition switch must be in the ACCESSORY (I) or ON (II) position. You operate the disc player with the same controls used for the radio. To select the disc player, press the CD/ AUX button. You will see ‘‘CD’’ in the display. Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit. This audio system can also play CD-Rs and CD-RWs compressed in MP3 or WMA formats.
Playing a Disc (Insight model) Text Data Display Function Each time you press the DISP button, the display shows you the text data on a disc, if the disc was recorded with text data. You cannot load and play 3-inch (8-cm) discs in this system. You can see the album, artist, and track name in the display. If a disc is recorded in MP3 or WMA, you can see the folder and file name, and the album, artist, and track tag.
Playing a Disc (Insight model) You will also see some text data under these conditions: When a new folder, file, or track is selected. When you change the audio mode to play a disc with text data or in MP3 or WMA. When you insert a disc, and the system begins to play. When playing a CD-DA with text data, the album and track name are shown in the display. With a disc in MP3 or WMA, the display shows the folder and file name.
Playing a Disc (Insight model) In MP3 or WMA mode FOLDER-REPEAT − This feature, when activated, replays all files in the selected folder in the order they are compressed. To activate folder repeat, press the RPT button twice. You will see F-RPT in the display. The system continuously replays the current folder. Press the RPT button again to turn it off. Pressing the RDM button, or selecting a different folder with the TUNE knob also turns off the repeat feature.
Playing a Disc (Insight model) In MP3 or WMA mode FOLDER-RANDOM − This feature, when activated, plays all files on the selected folder in random order. To activate folder random, press the RDM button. You will see F-RDM in the display. The system will then select and play files randomly. This continues until you deactivate folder random by pressing and holding the RDM button for 2 seconds.
Playing a Disc (Insight model) You can also eject the disc when the ignition switch is off. If you turn the system off while a disc is playing, either with the power/volume knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off. Features To Stop Playing a Disc Press the eject button ( ) to remove the disc.
Disc Player Error Messages (Insight model) If you see an error message in the display while playing a disc, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation.
Playing the FM/AM Radio (LX model and EX model without navigation system) BUTTON Features PRESET BUTTONS BUTTON VOL/SELECT KNOB A.
Playing the FM/AM Radio (LX model and EX model without navigation system) To Play the FM/AM Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the FM/AM button. Adjust the volume by turning the VOL/SELECT knob. The band and frequency that the radio was last tuned to are displayed. To change bands, press the FM/AM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction in AM is not available.
Playing the FM/AM Radio (LX model and EX model without navigation system) Preset − Each preset button can store one frequency on AM and two frequencies on FM. 1. Select the desired band, AM or FM. 3. Pick a preset button (1−6), then press and hold it until you hear a beep. 4. Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM. Press the A. SEL button. ‘‘A. SEL’’ flashes in the display, and the system goes into scan mode for several seconds.
Playing the FM/AM Radio (LX model and EX model without navigation system) If the station you are listening to is not an RDS station, the display continues to show the frequency with the PS name display function on. Radio Data System (RDS) On the FM band, you can select a favorite station and display the program service name provided by the radio data system (RDS). When you turn off this function by pressing the TITLE button, the display shows ‘‘RDS INFO OFF.
Playing the FM/AM Radio (LX model and EX model without navigation system) Radio Data System (RDS) Category With the FM band selected, you can select the program category provided by the RDS. Press or button to display and select an RDS category. The principal RDS categories are shown as follows; Press or button to select an RDS category. The display shows the selected RDS category name for about 10 seconds. You can use the search or scan function to find radio stations in the selected RDS category.
Playing the FM/AM Radio (LX model and EX model without navigation system) RDS Program Search RDS Program SCAN This function searches a frequency for a strong signal from the frequency that carry the selected RDS category information. This can help you to find a station in your favorite category. To activate it, press the or side of the SEEK button. You will see the selected RDS category name blinking while searching it.
Playing the FM/AM Radio (LX model and EX model without navigation system) SVC − Adjusts the volume level based on the vehicle speed. BAS − Adjusts the bass. The SVC mode controls the volume based on vehicle speed. The faster you go, the louder the audio volume becomes. As you slow down, the audio volume decreases. TREBLE − Adjusts the treble. FADER − Adjusts the front-to-back strength of the sound. BALANCE − Adjusts the side-toside strength of the sound. Each mode is shown in the display as it changes.
Playing a Disc (LX model and EX model without navigation system) BUTTON EJECT BUTTON BUTTON CD BUTTON DISC SLOT RDM BUTTON TITLE BUTTON RPT BUTTON SCAN BUTTON SEEK BUTTON SEEK BUTTON BUTTON 190
Playing a Disc (LX model and EX model without navigation system) Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit. This audio system can also play CD-Rs and CD-RWs compressed in MP3 or WMA formats. The numbers of the folder and track playing are shown in the display on the disc player. A disc can support more than 99 folders, and each folder can hold more than 255 playable files. A disc can hold up to 999 files in total.
Playing a Disc (LX model and EX model without navigation system) To Load a Disc Text Data Display Function Insert a disc about halfway into the disc slot. The drive will pull the disc in the rest of the way to play it. You operate the disc player with the same controls used for the radio. The number of the current track is shown in the display. When playing a disc in MP3 or WMA, the numbers of the current folder and file are shown. The system will continuously play a disc until you change modes.
Playing a Disc (LX model and EX model without navigation system) If you press and hold the TITLE button again, the display shows the first 15 characters again. You will also see some text data under these conditions: When a new folder, file, or track is selected. When you change the audio mode to play a disc with text data or in MP3 or WMA. When you insert a disc, and the system begins to play. When playing a CD-DA with text data, the album and track name are shown in the display.
Playing a Disc (LX model and EX model without navigation system) In MP3/WMA mode In MP3/WMA mode In MP3/WMA mode FOLDER SELECTION − To select a different folder, press the or button. Press the button to skip to the next folder, and the button to skip to the previous folder. FOLDER-REPEAT − This feature, when activated, replays all the files in the selected folder in the order they are compressed in MP3/WMA.
Playing a Disc (LX model and EX model without navigation system) In MP3/WMA mode FOLDER-SCAN − This feature, when activated, samples the first file in each folder on the disc in the order they are recorded. To activate the folder scan feature, press the SCAN button repeatedly. You will see ‘‘F-SCAN’’ in the display. The system will then play the first file in the main folders for about 10 seconds. When it plays a file that you want to continue listening to, press and hold the SCAN button.
Disc Player Error Messages (LX model and EX model without navigation system) The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For the additional information on damaged discs, see page 217 .
Playing an iPod (U.S.
Playing an iPod (U.S. LX model and EX model without navigation system) To Play an iPod This audio system can play the audio files on the iPod with the same controls used for the in-dash disc player. To play an iPod, connect it to the USB adapter cable in the console compartment by using your dock connector, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position. The iPod will also be recharged with the ignition switch in these positions.
Playing an iPod (U.S. LX model and EX model without navigation system) If the iPod indicator does not appear in the audio display, check the connections, and try to reconnect the iPod a few times. Connecting an iPod USB CONNECTOR USB ADAPTER CABLE 1. Unclip the USB connector by pivoting it, and pull out the USB adapter cable in the console compartment. DOCK CONNECTOR 2. Connect your dock connector to the iPod correctly and securely. 3. Install the dock connector to the USB adapter cable securely.
Playing an iPod (U.S. LX model and EX model without navigation system) Text Data Display Function Each time you press the TITLE button the display mode switches between the album name, the song name, the artist name, or name off (which turns off the text display). The display shows up to 16 characters of the selected data. If the text data has more than 16 characters, you will see the first 15 characters and the ＞ indicator in the display.
Playing an iPod (U.S. LX model and EX model without navigation system) The display shows items on the selected list. Turn the VOL/ SELECT knob to select an item, then press the VOL/SELECT knob to set your selection. Press the VOL/SELECT knob. Pressing the button goes back to the previous display and pressing the TITLE button cancels this setting mode. You can also select a file from any list on the iPod menu: playlists, artists, albums and songs, by using the VOL/SELECT knob.
Playing an iPod (U.S. LX model and EX model without navigation system) SHUFFLE ALBUM − This feature plays all available albums in a selected list (playlists, artists, albums or songs) in random order. The files in each album are played in the recorded order. To activate the shuffle album feature, press the RDM button repeatedly. You will see ‘‘F-RDM’’ in the display. To turn it off, press and hold the RDM button.
iPod Error Messages (U.S. LX model and EX model without navigation system) If you see an error message on the audio display while playing an iPod, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Cause USB ROM Error UNSUPPORTED VER. Use of unsupported iPod CONNECT RETRY Appears when an incompatible device is connected No files in iPod Recognition failure of iPod There is a problem with the USB adapter unit.
Playing a USB Flash Memory Device (U.S.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) The audio system reads and plays the audio files on the USB flash memory device in MP3, WMA or AAC＊ formats. Depending on the format, the display shows MP3, WMA or AAC when a USB flash memory device is playing. ＊: Only AAC format files recorded with iTunes are playable on this audio unit. The recommended USB flash memory devices are 256 MB or higher, and formatted with the FAT file system.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) NOTE: Do not use a device such as a card reader or hard drive as the device or your files may be damaged. Do not connect your USB flash memory device using a hub. Do not use an extension cable to the USB adapter cable equipped with your vehicle. Do not keep a USB flash memory device in the vehicle. Direct sunlight and high heat will damage it.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) When the USB flash memory device is connected, the USB indicator is shown in the display. Connecting a USB Flash Memory Device USB CONNECTOR Features USB ADAPTER CABLE 1. Unclip the USB connector by pivoting it, and pull out the USB adapter cable in the console compartment. USB ADAPTER CABLE 2. Connect the USB flash memory device to the USB connector correctly and securely.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) Text Data Display Function Each time you press the TITLE button, the display mode shows you in sequence, the folder name, the file name, the artist name, the album name, the song name, or name off (which turns off the text display). The display shows up to 16 characters of the selected data. If the text data has more than 16 characters, you will see the first 15 characters and the ＞ indicator in the display.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) To Select a File from Folder and File Lists Folder Selection To Select Repeat, Random or Scan Mode: You can select any type of repeat, random and scan modes by using the RPT button, RDM button, or SCAN button. Features Track Selection Pressing the button goes back to the previous display and pressing the TITLE button cancels this setting mode. Press the VOL/SELECT knob.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) REPEAT − This feature continuously plays a file. To activate the repeat feature, press the RPT button. You will see ‘‘RPT’’ in the display. To turn it off, press and hold the RPT button. FOLDER REPEAT − This feature replays all the files in the selected folder in the order they are stored. To activate the folder repeat feature, press the RPT button repeatedly. You will see ‘‘F-RPT’’ in the display.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) FOLDER RANDOM − This feature plays the files in the current folder in random order. To activate the folder random feature, press the RDM button repeatedly. You will see ‘‘F-RDM’’ in the display. To turn it off, press and hold the RDM button. FOLDER SCAN − This feature samples the first file in each folder in the order they are stored. To activate the folder scan feature, press the SCAN button repeatedly.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system) To Stop Playing a USB Flash Memory Device To play the radio when a USB flash memory device is playing, press the FM/AM button. If a disc is in the audio unit, press the CD button to play the disc. Disconnecting a USB Flash Memory Device You can disconnect the USB flash memory device at any time even if the USB mode is selected on the audio system.
USB Flash Memory Device Error Messages (U.S. LX model and EX model without navigation system) If you see an error message on the audio display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.
FM/AM Radio Reception Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
FM/AM Radio Reception Electrical interference from passing vehicles and stationary sources can cause temporary reception problems. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.
Protecting Your Discs General Information When using CD-R or CD-RW discs, use only high quality discs labeled for audio use. When recording a CD-R or CD-RW, the recording must be closed for it to be used by the system. Play only standard round discs. Odd-shaped discs may jam in the drive or cause other problems. Handle your discs properly to prevent damage and skipping. Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
Protecting Your Discs Examples of these discs are shown to the right: 1. Bubbled, wrinkled, labeled, and excessively thick discs Bubbled/ Wrinkled With Label/ Sticker 2. Damaged discs Chipped/ Cracked Using Printer Label Kit Sealed With Plastic Ring 3. Poor quality discs Warped Burrs CONTINUED 217 Features Additional Information on Recommended Discs The in-dash disc player/changer has a sophisticated and delicate mechanism.
Protecting Your Discs 4. Small, irregular shaped discs 3-inch (8-cm) CD 5. Discs with scratches, dirty discs Triangle Shape Fingerprints, scratches, etc. CD-R or CD-RW may not play due to the recording conditions. Scratches and fingerprints on the discs may cause the sound to skip. Can Shape 218 Arrow Shape Recommended discs are printed with the following logo. Audio unit may not play the following formats.
Remote Audio Controls The VOL button adjusts the volume up (▲) or down (▼). Press the top or bottom of the button and hold it until the desired volume is reached, then release it. CH BUTTON MODE BUTTON On U.S. LX model and EX models Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel. If you are listening to the radio, use the CH button to change stations.
Remote Audio Controls, Auxiliary Input Jack In MP3 or WMA mode, you can use the seek function to select folders. Press and hold the top (＋) of the CH button until you hear a beep to skip forward to the first file of the next folder. Press the bottom (−) to skip backward to the previous folder. If you are playing a PC card, press the top (＋) of the CH button to advance to the next file. Press the bottom (−) to go back to the previous file.
Radio Theft Protection The Anti-theft Identification Card also lists your audio serial number. It is best to store the card in a safe place at home. In addition, you should write the audio system’s serial number in this owner’s manual. If you make a mistake entering the code, do not start over; complete the five-digit sequence, then enter the correct code. You have ten tries to enter the correct code.
Setting the Clock (Models without navigation system) To set the time, press the CLOCK button until you hear a beep. The displayed time begins to blink. Insight model EX model without navigation system and LX model CLOCK BUTTON (A.SEL side of the A.SEL/SCAN bar) HOUR BUTTON (PRESET 1) Change the hours by pressing the H (hour) button until the numbers advance to the desired time. Change the minutes by pressing the M (minute) button until the numbers advance to the desired time.
Security System SECURITY SYSTEM INDICATOR Once the security system is sets, opening any door, the hatch, or the hood without using the key or the remote transmitter, will cause the alarm to activate. It also activates if the audio unit is removed from the dashboard or the wiring is cut. NOTE: To see if the system is set after you exit the vehicle, press the LOCK button on the remote transmitter within five seconds. If the system is set, the horn will beep once.
Cruise Control On LX and EX models Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather. Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather.
Cruise Control Changing the Set Speed You can increase the set cruising speed in any of these ways: To increase your speed in very small amounts, tap the RES/ ACCEL button. Each time you do this, the vehicle will speed up about 1 mph (1.6 km/h). Push on the accelerator pedal. Accelerate to the desired cruising speed, then press the SET/ DECEL button. Press and hold the SET/DECEL button. Release the button when you reach the desired speed. To slow down in very small amounts, tap the SET/DECEL button.
Cruise Control Canceling Cruise Control CRUISE BUTTON EX models only RES/ACCEL BUTTON CANCEL BUTTON SET/DECEL BUTTON You can cancel cruise control in any of these ways: Tap the brake pedal. Push the CANCEL button on the steering wheel. Push the CRUISE button on the steering wheel. 226 Tapping either of the paddle shifters shifts the speed up or down, but does not cancel the cruise control. For more information on driving with paddle shifters, see page 278 .
Bluetooth HandsFreeLink (Models without navigation system) Bluetooth HandsFreeLink (HFL) allows you to place and receive phone calls using voice commands, without handling your cell phone. To use HFL, you need a Bluetoothcompatible cell phone. For a list of compatible phones, pairing procedures, and special feature capabilities: Using HFL HFL Buttons HFL TALK BUTTON Features In the U.S., visit handsfreelink.honda. com or call (888) 528-7876. In Canada, visit www.handsfreelink.ca, or call (888) 528-7876.
Bluetooth HandsFreeLink (Models without navigation system) Voice Control Tips MICROPHONE Air or wind noise from the dashboard and side vents and all windows may interfere with the microphone. Adjust or close them as necessary. 228 Press and release the HFL Talk button each time you want to make a command. After the beep, speak in a clear, natural tone. Many commands can be spoken together. For example, you can say ‘‘Call 123-456-＃＃＃＃’’ or ‘‘Dial Peter.’’ Try to reduce all background noise.
Bluetooth HandsFreeLink (Models without navigation system) Help Features To hear general HFL information, including help on pairing a phone or setting up the system, say ‘‘Tutorial.’’ Information Display As an incoming call notification, you will see the following display: SIGNAL STRENGTH BATTERY LEVEL STATUS Features For help at any time, including a list of available commands, say ‘‘Hands free help.’’ Some phones may send battery, signal strength, and roaming status information to HFL.
Bluetooth HandsFreeLink (Models without navigation system) How to Use HFL The ignition switch must be in the ACCESSORY (I) or ON (II) position.
Bluetooth HandsFreeLink (Models without navigation system) Redial the last number called (See page 237) ‘‘Transfer’’ Transfer a call from HFL to your phone, or from your phone to HFL (See page 238) ‘‘Mute’’ Mute your voice to the person at the other end of the call (See page 238) ‘‘Send’’ Send numbers or names during a call (See page 238) Press HFL Talk button ‘‘Phonebook’’ Features ‘‘Redial’’ ‘‘Store’’ Store a phonebook entry (See page 239) ‘‘Edit’’ Edit the number of an existing phonebook e
Bluetooth HandsFreeLink (Models without navigation system) ‘‘Security’’ ‘‘System Set up’’ ‘‘Change Passcode’’ Change your security passcode (See page 242) ‘‘Call Notification’’ Set how you would like to be notified of an incoming call (See page 242) ‘‘Auto Transfer’’ Press HFL Talk button Apply a security passcode to the system that must be input at each key cycle to access the system (See page 241) ‘‘Clear’’ Set calls to automatically transfer from your phone to HFL when you enter the vehicle (Se
Bluetooth HandsFreeLink (Models without navigation system) To use HFL, you need to pair your Bluetooth-compatible cell phone to the system. Phone Setup This command group is available for paired cell phones. Phone pairing tips You cannot pair your phone while the vehicle is moving. Up to six phones can be paired. Your phone’s battery may drain faster when it is paired to HFL. If after three minutes your phone is not ready to pair or a phone is not found, the system will time out and return to idle. 2.
Bluetooth HandsFreeLink (Models without navigation system) To rename a paired phone: To delete a paired phone: Press and release the HFL Talk button before a command. Press and release the HFL Talk button before a command. 1. Say ‘‘Phone setup.’’ 1. Say ‘‘Phone setup.’’ 2. Say ‘‘Edit ’’ after the prompts. 2. Say ‘‘Delete’’ after the prompts. 3. If there is more than one phone paired to the system, HFL will ask you which phone’s name you want to change. Follow the HFL prompts and rename the phone.
Bluetooth HandsFreeLink (Models without navigation system) To hear which paired phone is currently linked: To change from the currently linked phone to another paired phone: Press and release the HFL Talk button before a command. Press and release the HFL Talk button before a command. 1. Say ‘‘Phone setup.’’ 1. Say ‘‘Phone setup.’’ 2. Say ‘‘Status’’ after the prompts. 2. Say ‘‘Next phone’’ after the prompts. To change the pairing code setting: Press and release the HFL Talk button before a command.
Bluetooth HandsFreeLink (Models without navigation system) Making a Call You can make calls using a name in the HFL phonebook or any phone number. You can also redial the last number called. HFL uses a Class 2 Bluetooth, which means, the maximum range between your phone and vehicle is 30 feet (10 meters). During a call, HFL allows you to talk up to 30 minutes after you remove the key from the ignition switch. However, this may weaken the vehicle’s battery.
Bluetooth HandsFreeLink (Models without navigation system) To redial the last number called by HFL: Press and release the HFL Talk button and say ‘‘Redial.’’ Receiving a Call When you receive a call, an incoming call notification (if activated) will play and interrupt the audio system if it is on. To return to the original call, press the HFL Talk button again. If you don’t want to answer the incoming call, disregard it and continue with your original call.
Bluetooth HandsFreeLink (Models without navigation system) Transferring a Call You can transfer a call from HFL to your phone, or from your phone to HFL. Muting a Call You can mute your voice to the person you are talking to during a call. Press and release the HFL Talk button and say ‘‘Transfer.’’ To mute your voice during a call, press and release the HFL Talk button and say ‘‘Mute.’’ To unmute your voice, press and release the HFL Talk button and say ‘‘Mute’’ again.
Bluetooth HandsFreeLink (Models without navigation system) To store a phonebook entry: Press and release the HFL Talk button before a command. NOTE: Avoid using duplicate name entries. Avoid using ‘‘home’’ as a name entry. To edit the number stored in a name: Press and release the HFL Talk button before a command. 1. Say ‘‘Phonebook .’’ 2. Say ‘‘Edit ’’ after the prompts. It is easier for HFL to recognize a multisyllabic or longer name.
Bluetooth HandsFreeLink (Models without navigation system) To delete a name: To list all names in the phonebook: Press and release the HFL Talk button before a command. Press and release the HFL Talk button before a command. 1. Say ‘‘Phonebook .’’ 1. Say ‘‘Phonebook .’’ 2. Say ‘‘Delete’’ after the prompts. 2. Say ‘‘List ’’ after the prompts. 3. Say the name you want to delete and follow the HFL prompts to complete the deletion. 3. HFL begins reading the names in the order they were stored.
Bluetooth HandsFreeLink (Models without navigation system) System Setup This command group allows you to change or customize HFL basic settings. To set a 4-digit passcode to lock the HFL system for security purposes: Press and release the HFL Talk button before a command. 1. Say ‘‘System setup.’’ NOTE: Once a passcode is set, you will need to enter it to use HFL each time you start the vehicle.
Bluetooth HandsFreeLink (Models without navigation system) Press and release the HFL Talk button before a command. To change your security passcode: To select either a ring tone or a prompt as the incoming call notification＊: 1. Say ‘‘System setup.’’ Press and release the HFL Talk button before a command. 2. Say ‘‘Change passcode’’ after the prompts. 3. Follow the HFL prompts and say the new 4-digit passcode. 4. Follow the HFL prompts to confirm the number.
Bluetooth HandsFreeLink (Models without navigation system) Quick Language Selection Canadian models only To quickly change the language: Press and release the HFL Talk button before a command. Press and release the HFL Talk button before a command. 1. Say the language you want to change to in that language. 1. Say ‘‘System setup.’’ 2. Follow the HFL prompts.
Bluetooth HandsFreeLink (Models without navigation system) Change Language Canadian models only To change the system language between English and French: Press and release the HFL Talk button before a command. 1. Say ‘‘Change language.’’ 2. Follow the HFL prompts to change the language to English or French. If you have not named your paired phone in the language you just selected, HFL will ask you to name it in the current language.
Before Driving Break-in Period .............................. 246 Fuel Recommendation .................. 246 Service Station Procedures .......... 247 Refueling..................................... 247 Tighten Fuel Cap Message ...... 249 Opening and Closing the Hood ........................................ 250 Oil Check .................................... 251 Engine Coolant Check .............. 252 Fuel Economy ................................ 253 Accessories and Modifications .... 256 Carrying Cargo .....
Break-in Period, Fuel Recommendation Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Fuel Recommendation Your vehicle is designed to operate on unleaded gasoline with a pump octane number of 87 or higher. Use of a lower octane gasoline can cause a persistent, heavy metallic rapping noise that can lead to engine damage. Avoid full-throttle starts and rapid acceleration.
Fuel Recommendation, Service Station Procedures For further important fuel-related information for your vehicle, or information on gasoline that does not contain MMT, visit Owner Link at owners.honda.com. In Canada, visit www.honda.ca for additional information on gasoline. For more information on top tier gasoline, visit Refueling FUEL FILL DOOR www.toptiergas.com. Push 1. Park with the driver’s side closest to the service station pump. 2.
Service Station Procedures Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. HOLDER FUEL FILL CAP Stop the engine, and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. TETHER 3. Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank equalizes. The fuel fill cap is attached to the fuel filler with a tether. Place the cap in the holder on the fuel fill door. 248 4.
Service Station Procedures Tighten Fuel Cap Message Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another message, press the INFO button. The ‘‘TIGHTEN FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off. 6.
Service Station Procedures If the system still detects a leak in the vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page 367 .
Service Station Procedures To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched. GRIP DIPSTICK CLIP 3. Holding the grip, pull the support rod out of its clip. Insert the end into the designated hole in the hood. Wait a few minutes after turning the engine off before you check the oil. 1. Remove the dipstick (orange loop).
Service Station Procedures Engine Coolant Check MAX RESERVE TANK UPPER MARK LOWER MARK MIN 4. Remove the dipstick again, and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Engine Oil on page 312 . 252 Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If it is below the MIN line, see Adding Engine Coolant on page 317 for information on adding the proper coolant.
Fuel Economy Actual Mileage and EPA Fuel Economy Estimates Comparison. Fuel economy is not a fixed number. It varies based on driving conditions, driving habits, and vehicle condition. Therefore, it is not possible for one set of estimates to predict fuel economy precisely for all drivers in all environments. City MPG − Represents urban driving in light traffic. A range of miles per gallon achieved is also provided.
Fuel Economy Fuel Economy Factors The following factors can lower your vehicle’s fuel economy: Aggressive driving (hard acceleration and braking) Excessive idling, accelerating and braking in stop-and-go traffic Cold engine operation (engines are more efficient when warmed up) Driving with a heavy load or the air conditioner running Improperly inflated tires Use the recommended viscosity motor oil, displaying the API Certification Seal (see page 313).
Fuel Economy Minimize the use of the air conditioning system − The A/C puts an extra load on the engine which makes it use more fuel. Use the fresh-air ventilation when possible. Miles driven Gallons of fuel Miles per Gallon 100 Liter Kilometers Before Driving Plan and combine trips − Combine several short trips into one. A warmed-up engine is more fuel efficient than a cold one.
Accessories and Modifications Modifying your vehicle, or installing non-Honda accessories, may make your vehicle unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Honda accessories that allow you to personalize your vehicle. These accessories have been designed and approved for your vehicle, and are covered by warranty.
Accessories and Modifications Non-Honda wheels, because they are a universal design, can cause excessive stress on suspension components and will not be compatible with the tire pressure monitoring system (TPMS)＊. Some examples are: Larger or smaller wheels and tires can interfere with the operation of your vehicle’s anti-lock brakes and other systems.
Carrying Cargo FLOOR STORAGE COMPARTMENT DOOR POCKETS CENTER POCKET GLOVE BOX However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, and make it unsafe. Before carrying any type of cargo, be sure to read the following pages. CARGO AREA UNDER FLOOR STORAGES SEAT-BACK POCKETS＊ CENTER TRAY＊/ CENTER POCKET＊ CONSOLE COMPARTMENT＊ EX with navigation system model is shown.
Carrying Cargo Load Limits The maximum load for your vehicle is 850 lbs (385 kg). See Tire And Loading Information label attached to the driver’s doorjamb. Label Example Follow all load limits and other loading guidelines in this manual. Steps for Determining Correct Load Limit − (1)Locate the statement ‘‘The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.’’ on your vehicle’s placard.
Carrying Cargo Example 1 Max Load 850 lbs (385 kg) Passenger Weight 150 lbs x 2 = 300 lbs (68 kg x 2 = 136 kg) Cargo Weight 550 lbs (249 kg) Max Load 850 lbs (385 kg) Passenger Weight 150 lbs x 4 = 600 lbs (68 kg x 4 = 272 kg) Cargo Weight 250 lbs (113 kg) Max Load 850 lbs (385 kg) Passenger Weight 150 lbs x 5 = 750 lbs (68 kg x 5 = 340 kg) Cargo Weight 100 lbs (45 kg) Example 2 Example 3 260 In addition, the total weight of the vehicle, all occupants, accessories, cargo, and trailer tongue loa
Carrying Cargo Carrying Items in the Passenger Compartment Store or secure all items that could be thrown around and hurt someone during a crash. Keep the glove box closed while driving. If it is open, a passenger could injure their knees during a crash or sudden stop. Try to secure the items with rope or cord so they will not shift while you are driving. Do not place items on the cargo area cover (if equipped), or stack objects higher than the top of the back seat.
Carrying Cargo Air Intake AIR INTAKE The air intake for the IMA battery and electronics is located on the rear left pillar. Do not block this air intake. Doing so may cause the IMA battery and the power control unit to overheat, causing the IMA to shut down. It will start working again after it cools. 262 Do not spill any liquids over the air intake or insert any foreign objects in it. This may damage the IMA battery and the power control unit.
Driving This section gives you tips on starting the engine under various conditions, and how to operate the automatic transmissions (CVT). It also includes important information on parking your vehicle, the braking system, the vehicle stability assist (VSA ) system, and the tire pressure monitoring system (TPMS). 263 Driving Preparing to Drive ......................... 264 Starting the Engine........................ 265 Eco Assist System ......................... 266 Automatic Transmission (CVT) ..
Preparing to Drive You should do the following checks and adjustments before you drive your vehicle. 4. Check that any items you may be carrying are stored properly or fastened down securely. 9. Fasten your seat belt. Check that your passengers have fastened their seat belts (see page 17 ). 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 5. Check the seat adjustment (see page 141 ). 10.
Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Make sure the shift lever is in Park. Press on the brake pedal. The engine is harder to start in cold weather. Also, the thinner air f ound at altitudes above 8,000 f eet (2,400 meters) adds to this problem. Driving 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Eco Assist System ECON MODE INDICATOR Ambient Meter ECON BUTTON ECO-drive Result ECO-guide feedback Eco Assist System is a driver feedback system designed to help you develop and maintain a fuel efficient driving style. The system monitors your driving style, and can display how it impacts your vehicle’s fuel economy. You can then make adjustments to your driving style to maximize fuel economy. (For additional information on fuel economy, see page 253 .
Eco Assist System Eco Guide Feedback Center Position Acceleration Deceleration Monitor Monitor ECO DRIVE BAR The Eco Drive Bar on the Eco guide feedback display appears on the multi-information display while you drive. During deceleration, the bar extends to the left of the center line. If the bar stays within the Efficient Driving Zones, your current driving style is conducive to good fuel economy.
Eco Assist System Ambient Meter AMBIENT METER (Background Color) Meter Background Color Fuel Economy Green High Blue Green U.S. model is shown. The Ambient Meter (the light behind the speedometer) changes color to show the effects of your driving style. This feature can be turned off (see page 103 ).
Eco Assist System Eco Assist Scoring A point system is used so you can monitor your driving style and the impact on fuel economy.
Eco Assist System Drive Cycle Score − The score from your just completed trip is represented on the Eco Score screen by the ‘‘plant’’ icons. Drive Cycle Score/Lifetime Points TROPHY STAGE-UP RECOGNITION ICON Lifetime Points − Cumulative, or lifetime trips, which build up over time, represented by a bar graph at the bottom of the Eco Score display. Each time you turn the ignition switch to the LOCK (0) position, the Eco Score displays for a few seconds to show your current stage and lifetime points.
Eco Assist System There are three Eco stages, with five plants per stage. As you accumulate a specified number of leaves, you advance from one stage to the next. The plant grows leaves from left to right, or loses them from right to left. A trophy icon appears once you have reached the maximum third stage score. Real time scores must accumulate over time to result in a stage change.
Eco Assist System As you progress to a higher level, the system monitors your driving style more strictly. As a result, you must further refine your driving style to continue to move up to the next level.
Automatic Transmission (CVT) Continuously Variable Transmission (CVT) Honda’s Continuously Variable Transmission’s unique design provides a smooth, constant flow of power. It is electronically controlled for more precise operation and better fuel economy. Shift Lever Position Indicators These indicators on the instrument panel show which position the shift lever is in. The ‘‘D’’ indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position.
Automatic Transmission (CVT) Shifting Insight and LX models To shift from: P to R R to P N to R D to S S to L L to S S to D D to N N to D R to N To shift from Park to any position, press the brake pedal, the release button on the front of the shift lever, then pull the lever. You cannot shift out of Park when the ignition switch is in the LOCK (0) or the ACCESSORY (I) position. 274 EX models Do this: Press the brake pedal and press the release button. To shift from: Press the release button.
Automatic Transmission (CVT) Park (P) − This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Press the release button on the front of the shift lever to move it. You must also press the release button to shift into Park. To avoid transmission damage, come to a complete stop before shifting into Park.
Automatic Transmission (CVT) Insight and LX models EX models Low (L) − To shift to Low, press the release button on the front of the shift lever. Use Low to make better use of engine power when climbing, and for maximum engine braking when going down steep hills. Second (S) − To shift into the S position, press the release button on the front of the shift lever, and move the lever to S.
Automatic Transmission (CVT) Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. RELEASE BUTTON 1. Set the parking brake. 2. Remove the key from the ignition switch. 4. Insert the key in the shift lock release slot. 5. Push down on the key while you press the release button on the shift lever and move the shift lever out of Park to neutral. 6.
Driving with the Paddle Shifters Using the Paddle Shifters in the D position (D-Paddle Shift Mode) On EX models When you are driving in the D position, pulling either paddle shifter switches from the D-normal shift mode to the D-paddle shift mode. You can shift the transmission up or down through seven-stages manually with the paddle shifters. Downshifting gives you more power when climbing, and provides engine braking when going down a steep hill.
Driving with the Paddle Shifters Downshifting with the − (left) paddle shifter allows you to increase the engine braking when going down steep or long hills, and provides more power when climbing uphills. You can upshift the transmission manually to reduce the rpm. To cancel the D-paddle shift mode manually, pull and hold the ＋ side paddle shifter until the shift indicator goes out. The transmission remains in the selected speed if you do not accelerate.
Driving with the Paddle Shifters Each time you pull either paddle shifter, the transmission shifts one speed up or down. If you want to shift up or down more than two speeds, pull the paddle shifter twice, pause, and then pull it again. The automatic transmission (CVT) will not allow you to shift if: You downshift before the engine speed reaches the highest threshold of the lower speed.
Driving with the Paddle Shifters Using the Paddle Shifters in the S position (7-Speed Manual Shift Mode) ‘‘M’’ INDICATOR On EX models With the shift lever in the S position, you can select the 7-Speed Manual shift mode to shift speeds; much like a manual transmission using the paddle shifters, but without a clutch pedal. The transmission also shifts automatically as the vehicle comes to a complete stop. It downshifts to first speed when the vehicle speed reaches 6 mph (10 km/h) or less.
Driving with the Paddle Shifters The automatic transmission (CVT) will not allow you to shift if: You downshift before the engine speed reaches the highest threshold of the lower speed. If you try to do this, the shift indicator will flash the number of the lower speed several times, then return to a higher speed. You upshift before the engine speed reaches the lowest threshold of the higher speed. You pull both paddle shifters at the same time.
Auto Idle Stop To help maximize fuel economy, your vehicle has an Auto Idle Stop function. Depending on environmental conditions and vehicle operation, the engine will shut off when you come to a stop. When the ECON mode is on, the engine is more likely to stop than when it is off (see page 127 ). The engine will not stop automatically under the following conditions: Vehicle speed does not go above 9 mph (15 km/h) after starting the engine. The transmission fluid temperature is low.
Auto Idle Stop The engine may not stop automatically under the following conditions: The ECON button is off, and there is a significant difference between the ambient temperature and the temperature setting of the climate control system. The climate control system is dehumidifying the air. The engine automatically restarts when: The engine coolant temperature becomes low. The brake pedal is released. The pressure on the brake pedal is repeatedly applied and released slightly during a stop.
Auto Idle Stop Auto Idle Stop Indicator If the auto idle stop function turns off the engine for a long time, the charge of the IMA and 12 volt batteries becomes low, and the engine may not restart automatically. Always turn the ignition switch to the LOCK (0) position, set the parking brake, and remove the key if you are getting out of the vehicle. The time that auto idle stop is activated may be reduced if you operate the windshield wipers with the climate control system on.
Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline. Set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission. Parking Tips Make sure the windows are closed. Turn off the lights. Place any packages, valuables, etc. in the cargo area or take them with you. Lock the doors and the hatch.
Braking System Your vehicle is equipped with front disc brakes. The brakes on the rear wheels are drum. A power assist helps reduce the effort needed on the brake pedal. The ABS helps you retain steering control when braking very hard. Constant application of the brakes when going down a long hill builds up heat and reduces their effectiveness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower speed. Check the brakes after driving through deep water.
Braking System Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.
Anti-lock Brakes (ABS) The anti-lock brake system (ABS) helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it. You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal: it is the ABS rapidly pumping the brakes. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates.
Anti-lock Brakes (ABS) If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the EBD system may also be shut down. Test your brakes as instructed on page 368 . If the brakes feel normal, drive slowly and have your vehicle repaired by your dealer as soon as possible. Avoid sudden hard braking which could cause the rear wheels to lock up and possibly lead to a loss of control.
Tire Pressure Monitoring System (TPMS) U.S. models only Your vehicle is equipped with a tire pressure monitoring system (TPMS) that turns on every time you start the engine and monitors the pressure in your tires while driving. If you think you can safely drive a short distance to a service station, proceed slowly to the station, then inflate the tire to the recommended pressure.
Tire Pressure Monitoring System (TPMS) For example, if you check and fill your tires in a warm area, then drive in extremely cold weather, the tire pressure will be lower than measured and could be underinflated and cause the low tire pressure/ TPMS indicator to come on. Or, if you check and adjust your tire pressure in cooler conditions, and drive into extremely hot conditions, the tires may become overinflated. However, the low tire pressure/ TPMS indicator will not come on if the tires are overinflated.
Tire Pressure Monitoring System (TPMS) Also, the low tire pressure/TPMS indicator begins to flash, then stays on (see page 291 ). When you restart the vehicle with the compact spare tire, the TPMS system message will also be displayed on the multi-information display after several miles (kilometers) driving. After the flat tire is replaced with the spare tire, the low tire pressure/ TPMS indicator stays on while driving.
Tire Pressure Monitoring System (TPMS) Never use a puncture-repairing agent in a flat tire. If used, you will have to replace the tire pressure sensor. Have the flat tire repaired by your dealer as soon as possible. As required by the FCC: This device complies with Part 15 of the FCC rules.
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System On U.S. models If the low tire pressure/TPMS indicator comes on (see page 291 ), or the multi-information display shows a ‘‘CHECK TPMS SYSTEM’’ message with the indicator flashing (see page 292 ), the VSA system automatically turns on even if the VSA system is turned off with the VSA OFF switch. In this case, you cannot turn the VSA system off by pressing the VSA OFF switch again.
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction. When replacing tires, make sure they are of the same size and type as your original tires (see page 344 ). To activate hill start assist, you must come to a complete stop and make sure the shift lever is in any of D, S or L (either in D or S on models with the paddle shifters) when facing uphill, or reverse when facing downhill.
Towing a Trailer Your vehicle is not designed to tow a trailer. Attempting to do so can void your warranties.
Maintenance This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions. This section also includes instructions on how to read the Maintenance Minder messages on the multi-information display, and instructions for simple maintenance tasks you may want to take care of yourself. Maintenance Safety ....................... 300 Maintenance MinderTM.................. 301 Fluid Locations...............................
Maintenance Safety All service items not detailed in this section should be performed by a certified technician or qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required. Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off. To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.
Maintenance MinderTM Your vehicle displays engine oil life and maintenance service items on the multi-information display to show you when you should have your dealer perform engine oil replacement and indicated maintenance service. Based on the engine operating conditions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.
Maintenance MinderTM MAINTENANCE SUB ITEM CODE(S) Pressing either INFO button (▲/▼) switches the display from the message to another display. Once you switch the display, this message will go off. SUB ITEM(S) Along with the message, the system message indicator comes on (see page 70 ).
Maintenance MinderTM Pressing either INFO button (▲/▼) switches the display from the message to another display. Once you switch the display, this message will go off. Along with the message, the system message indicator comes on (see page 70 ). Press the SEL/RESET button on the steering wheel repeatedly to select the engine oil life.
Maintenance MinderTM These messages will come on every time you turn the ignition switch to the ON (II) position. Immediately have the service performed, and make sure to reset the display as described on page 306 . Pressing either INFO button (▲/▼) switches the display from the message to another display. To see the message again, press either INFO button repeatedly.
Maintenance MinderTM NEGATIVE DISTANCE TRAVELED U.S. Canada This message is displayed again when you drive over 10 miles (for U.S. models) or 10 km (for Canadian models) after seeing the 0% message. U.S. Canada Immediately have the service performed, and make sure to reset the display as described on page 306 .
Maintenance MinderTM Maintenance Main Items and Sub Items MESSAGE DISPLAY MAINTENANCE MAIN ITEM ENGINE OIL LIFE DISPLAY MAINTENANCE SUB ITEMS All the maintenance items displayed in the multi-information display are in code. For an explanation of the maintenance codes, see page 310 . 306 Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service.
Maintenance MinderTM SEL/RESET BUTTON DX model Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the correct maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed. INFO BUTTON (▲/▼) Maintenance 4.
Maintenance MinderTM Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described.
Maintenance MinderTM U.S. Vehicles: According to state and federal regulations, failure to perform maintenance on the items marked with ＃ will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the multiinformation display. Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.
Maintenance MinderTM Maintenance Minder Symbol A B Maintenance Main Items Replace engine oil＊ Replace engine oil＊ and oil filter Inspect front and rear brakes Check parking brake adjustment Inspect these items: Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS/VSA) All fluid levels and condition of fluids Exhaust system＃ Fuel lines and connections＃ ＊ : If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is
Fluid Locations BRAKE FLUID (Black cap) ENGINE OIL FILL CAP AUTOMATIC TRANSMISSION (CVT) FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) ENGINE COOLANT RESERVOIR RADIATOR CAP 311 Maintenance ENGINE OIL DIPSTICK (Orange loop)
Adding Engine Oil ENGINE OIL FILL CAP Unscrew and remove the engine oil fill cap on the valve cover. Pour the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment. 312 Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick. Do not fill above the upper mark; you could damage the engine.
Adding Engine Oil API CERTIFICATION SEAL Ambient Temperature Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API Certification Seal and it is the proper weight. You must follow the oil and filter change intervals shown on the multiinformation display. Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.
Changing the Oil and Filter Always change the oil and filter according to the maintenance messages shown on the multiinformation display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service stationtype hydraulic lift for this service.
Changing the Oil and Filter 6. Install a new oil filter according to the instructions that come with it. Make sure to clean off any dirt and dust on the contacting surface of a new oil filter. BOLT 7. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (39 N·m , 4.0 kgf·m) WASHER 5. Remove the oil filter, and let the remaining oil drain. A special wrench (available from your dealer) is required.
Changing the Oil and Filter 9. Reinstall the engine oil fill cap. Start the engine. The oil pressure indicator should go out within 5 seconds. If it does not, turn off the engine, and check your work. 10.Let the engine run for several minutes, then check the drain bolt and oil filter for leaks. 316 11.Turn off the engine, let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil. 12.Put the under-cover back in place and reinstall the holding clips and screws.
Engine Coolant Adding Engine Coolant RESERVE TANK If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
Engine Coolant If the reserve tank is completely empty, you should also check the coolant level in the radiator. 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment. Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Windshield Washers Check the fluid level in the windshield washer reservoir at least monthly during normal use. On all Canadian models If the washer fluid is low, a ‘‘WASHER FLUID LOW’’ message appears on the multi-information display. Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. Do not use engine antif reeze or a vinegar/water solution in the windshield washer reservoir.
Automatic Transmission Fluid Continuously Variable Transmission (CVT) Check the fluid level with the engine at normal operating temperature. 1. Park the vehicle on level ground. Start the engine, let it run until the radiator fan comes on, then shut off the engine. For accurate results, wait about 60 seconds (but no longer than 90 seconds) before doing step 2. HOT Range LOWER MARK DIPSTICK 2. Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth. 3.
Automatic Transmission Fluid, Brake Fluid 5. If the level is below the lower mark, add fluid into the dipstick hole to bring it to the level between the upper and lower marks. Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment. 6. Insert the dipstick all the way back into the transmission securely.
Brake Fluid Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. Using any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible. Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.
Lights Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the cargo area, readjustment may be required. Adjustments should be done by your dealer or another qualified technician. Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter. HOLDING CLIP CONNECTOR 1. Open the hood.
Lights CONNECTOR BULB 6. Install the new bulb, and turn it one-quarter turn clockwise to lock it in place. 7. Push the electrical connector back onto the bulb. Make sure it is on all the way. 8. Reinstall the cover over the back of the headlight assembly and turn it clockwise to lock it in place. Push the electrical connector back onto the cover. COVER 4. Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down. 324 5.
Lights (Right side) 10.Install the upper part of the windshield washer reservoir tank in the reverse order of removal. Low Beam Headlight BULB 4. Install the new bulb, and turn it one-quarter turn clockwise to lock it in place. 5. Push the electrical connector back onto the bulb. Make sure it is on all the way. 6. Turn on the headlights to test the new bulb. CONNECTOR Maintenance 1. Open the hood. 2. Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down. 3.
Lights 4. Install the socket back into the headlight assembly. Turn it clockwise to lock it in place. Replacing a Front Parking Light Bulb BULB HOLDING CLIP 5. Turn on the lights to make sure the new bulb is working. (Right side) 6. Install the upper part of the windshield washer reservoir tank in the reverse order of removal. SOCKET 1. Open the hood. To change the bulb on the right side, remove the upper part of the windshield washer reservoir tank.
Lights 4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Replacing the Front Turn Signal Light Bulb SOCKET BULB 5. Insert the socket back into the front turn signal light assembly. Turn it clockwise to lock it in place. 6. Turn on the lights to make sure the new bulb is working. COVER 1. Place a cloth on the notch of the light assembly garnish to prevent scratches. Remove the cover by carefully prying in the notch with a flat-tip screwdriver.
Lights Replacing a Front Side Marker Light Bulb 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. BULB 4. Install the socket back into the headlight assembly. Turn it clockwise to lock it in place. SOCKET 1. Open the hood. 2. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise. 328 5. Turn on the lights to make sure the new bulb is working.
Lights Replacing the Rear Bulbs HOOKS CLIP TRIM HOOKS CLIP 2. Push on the area of the trim as shown in the illustration above to detach the upper hooks from the light assembly. 3. Pry on the gap between the trim and light assembly carefully with a flat-tip screwdriver to detach the lower hooks. 4. Make sure that all hooks are removed from the light assembly. Unclip the top half of the trim from the body by pulling it out. Then unclip the bottom half. CONTINUED 329 Maintenance 1. Open the hatch.
Lights BOLT Front Left side Front BULB ORIGINAL POSITION 5. Remove the two mounting bolts with an 8 mm wrench. Left side 6. Pull the rear of the light assembly out as shown in the illustration above ( ), then push the assembly back to the original position carefully ( ). The front part of the rear light assembly raises slightly ( ). 7. Determine which of the three bulbs is burned out: back-up light, turn signal, or side marker. 330 SOCKET SNAP FASTENERS 8.
Lights 11.Install the new bulb in the socket by pushing it straight in the socket until it bottoms. 12.Reinstall the socket into the light assembly. Turn it clockwise to lock it in place. 13.Test the lights to make sure the new bulb is working. 15.To reinstall the trim, set the bottom edge of the trim in the original position and push the bottom half of the trim to clip it back securely. Then push the upper half of the trim to secure the top clip. 16.
Lights Stop/taillights The stop/taillights should be replaced by your dealer. Rear License Plate Light Bulbs The license plate has two lights above it. The bulbs should be replaced by your dealer. Side Turn Signal Lights EX models Each outside mirror has side turn signal lights. The lights should be replaced by your dealer. 332 High-mount Brake Light The high-mount brake light should be replaced by your dealer.
Audio Antenna, Cleaning the Seat Belts, Floor Mats Audio Antenna Cleaning the Seat Belts Floor Mats LOOP To unlock Driver’s floor mat is shown. Before entering or parking in areas with low ceiling height, remove the antenna. If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air dry before you use the vehicle.
Floor Mats, Dust and Pollen Filter, Wiper Blades If you remove a floor mat, make sure to re-anchor it when you put it back in your vehicle. If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats. Make sure the rear floor mats are properly positioned. If not, the floor mat will interfere with the seat operation and make the front passenger’s weight sensors ineffective.
Wiper Blades WIPER ARM WIPER ARMS 1. Raise each wiper arm off the windshield, lifting the driver’s side first, then the passenger’s side. 2. Disconnect the blade assembly from the wiper arm: Put a cloth on the edge of the lock tab to prevent scratches, then push up on the lock tab carefully with a flat-tip screwdriver. Pivot the blade assembly toward the wiper arm until it releases from the wiper arm.
Wiper Blades BLADE 4. Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade. BLADE 3. Remove the blade from its holder by grabbing the tabbed end of the blade. Pull firmly until the tabs come out of the holder. 5. Place the top of the wiper blade on the end of the blade assembly, and slide the blade onto the assembly.
Wiper Blades 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. REAR 7. Make sure the blade is completely installed and that its edge is not bunched up. 8. Lower the wiper arm down against the windshield, the passenger’s side first, then the driver’s side. COVER 1. Raise the wiper arm off the rear window. 2. Disconnect the blade assembly from the wiper arm by pulling up the cover.
Wiper Blades WIPER ARM BLADE 5. Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade. REINFORCEMENT TOP BLADE 3. Push the blade assembly toward the base of the arm. When replacing a wiper blade, make sure not to drop the wiper blade or wiper arm down on the windshield. 4.
Wiper Blades 7. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 8. Make sure the blade is completely installed and that its edge is not bunched up. 9. Lower the wiper arm down against the windshield. Maintenance 6. Place the top of the wiper blade on the end of the blade assembly, and slide the blade onto the assembly. Make sure the blade is completely installed.
Tires Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced. Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding tire inflation and maintenance.
Tires Recommended Tire Pressures The following chart shows the recommended cold tire pressures for most normal driving conditions. You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges. The compact spare tire pressure is: 60 psi (420 kPa , 4.
Tires INDICATOR LOCATION MARKS TREAD WEAR INDICATOR Your tires have wear indicators molded into the tread. When the tread wears down, you will see a 1/2 inch (12.7 mm) wide band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire this worn gives very little traction on wet roads. You should replace the tire if you can see three or more tread wear indicators.
Tires Tire Rotation Front Front (Front Non-directional (Front Directional Tires and Wheels) Tires and Wheels) It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling. Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy.
Tires Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tires recommended in this owner’s manual. Wheel and Tire Specifications Wheels: 15 x 6J Tires: P185/60R15 84T See page 384 for DOT tire quality grading information, and page 384 for tire size information.
Tires When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads. Follow all instructions in this owner’s manual regarding the selection and use of tire chains.
Checking the 12 Volt Battery Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent further corrosion. TEST INDICATOR WINDOW Check the condition of the 12 volt battery monthly by looking at the test indicator window.
Checking the 12 Volt Battery If your vehicle’s battery is disconnected, or goes dead, the time setting may be lost. To reset the time, see page 222 . If your vehicle’s battery is disconnected or goes dead, the audio system may disable itself. The next time you turn on the radio, you will see ‘‘ENTER CODE’’ in the frequency display. Use the preset buttons to enter the code (see page 221 ). On vehicles with navigation system The navigation system will also disable itself.
Vehicle Storage If you need to park your vehicle for an extended period (more than 1 month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors. If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground. Leave one window open slightly (if the vehicle is being stored indoors).
Taking Care of the Unexpected This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed. Compact Spare Tire....................... 350 Changing a Flat Tire ..................... 351 If the Engine Won’t Start ..........
Compact Spare Tire Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can. Check the air pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm ) Follow these precautions: Never exceed 50 mph (80 km/h). This tire gives a harsher ride and less traction on some road surfaces. Use greater caution while driving.
Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. TAB The vehicle can easily roll off the jack, seriously injuring anyone underneath. HOLDER Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack. FLOOR 3. Open the hatch. 4.
Changing a Flat Tire JACK BOX SPARE TIRE CASING 5. Take the box out of the spare tire. 6. Take the spare tire casing out of the cargo area. 7. Unscrew the wing bolt and take the spare tire out of its well. 352 SPARE TIRE KNOB COVER 8. Remove the jack compartment cover by pulling the knob. 9. Turn the jack’s end bracket counterclockwise to loosen it, then remove the jack. WHEEL NUT WRENCH 10.Loosen each wheel nut 1/2 turn with the wheel nut wrench.
Changing a Flat Tire JACKING POINTS EXTENSION WHEEL NUT WHEEL COVER Insight and LX models 12.Remove the wheel cover by carefully prying under its edge with the flat tip of the extension. EXTENSION 13.Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground. 14.Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up.
Changing a Flat Tire BRAKE HUB 16.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten the wheel nuts fully. 17.Lower the vehicle to the ground, and remove the jack. 15.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving. 354 18.
Changing a Flat Tire CARPET CENTER CAP EX models SPARE TIRE CASING 20.Place the flat tire face down in the spare tire well. 21.Remove the carpet from the spare tire casing and store it in the casing. 22.Install the spare tire casing in the original position in the spare tire well. SPACER CONE For normal tire For compact spare tire 23.Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt. 24.Secure the flat tire by screwing the wing bolt back into its hole.
Changing a Flat Tire 25.Store the tools in the spare tire casing and the jack in its holder. Turn the jack’s end bracket clockwise to lock it in place, and reinstall the cover. Loose items can fly around the interior in a crash and could seriously injure the occupants. Store the wheel, jack, and tools securely before driving. 26.Store the center cap in the cargo area. Make sure it does not get scratched or damaged. FLOOR 27.Place the cargo area floor in its original position. Close the hatch. U.S.
Changing a Flat Tire Installing a wheel cover CLIPS CLIPS Insight and LX models 2. Align the valve mark on the wheel cover to the tire valve on the wheel, then install the wheel cover. 3. Make sure the wire support ring is on the outer side of the tire valve as shown. 357 Taking Care of the Unexpected 1. Make sure the wire support ring is hooked into the clips around the edge of the wheel cover.
If the Engine Won’t Start The engine normally starts with the IMA motor. If the engine does not start while the IMA battery charge is normally sufficient, check the following: Check the transmission interlock. The transmission must be in Park or neutral or the starter will not operate. 358 Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page 130 ).
If the Engine Won’t Start When the IMA battery charge is low, the starter motor is used to start the engine. If the engine does not start, check the following: Turn the ignition switch to the ON (II) position. Turn on the headlights, and check their brightness. If the headlights are very dim or do not come on at all, the battery is discharged. See Jump Starting on page 360 .
Jump Starting Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery. You cannot start your vehicle by pushing or pulling it. 360 To jump start your vehicle: 1. Open the hood, and check the physical condition of the 12 volt battery. If a battery sits in extreme cold, the electrolyte inside can f reeze.
Jump Starting 6. Start the vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact. 7. Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery. 4. Connect the second jumper cable to the negative (−) terminal on the booster battery. Connect the other end to the grounding strap as shown.
Jump Starting, If the Engine Overheats If your vehicle’s 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading will not be correct the next time you turn the ignition switch to the ON (II) position. It will show less than the actual level temporarily. It will show the correct level after you drive for at least 30 minutes. If the Engine Overheats The high temperature indicator should be off under most conditions.
If the Engine Overheats Steam and spray from an overheated engine can seriously scald you. Do not open the hood if steam is coming out. 1. Safely pull to the side of the road. Put the transmission in Park, and set the parking brake. Turn off all the accessories, and turn on the hazard warning lights. 2. If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood. 3.
If the Engine Overheats Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator cap. 8. Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off. 364 9.
Low Oil Pressure Indicator This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action. You will also see a ‘‘CHECK ENGINE OIL LEVEL’’ message on the multi-information display when this indicator comes on. Running the engine with low oil pressure can cause serious mechanical damage almost immediately.
12 Volt Battery Charging System Indicator If the charging system indicator comes on brightly when the engine is running, the 12 volt battery is not being charged. You will also see a ‘‘CHECK CHARGING SYSTEM’’ message on the multi-information display (see page 89 ). Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows. Keep the engine running; starting the engine will discharge the battery rapidly.
Malfunction Indicator Lamp If the indicator comes on while driving, it means one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage. If your vehicle’s battery has been disconnected or gone dead, these codes are erased. It can take several days of driving under various conditions to set the codes again.
Brake System Indicator U.S. Canada (Red) The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position and as a reminder to check the parking brake. If you do not release the parking brake, the indicator will stay on, and you will see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display. If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal.
Fuses FUSE BOX INTERIOR COVER LABEL The vehicle’s fuses are contained in three fuse boxes. CONTINUED 369 Taking Care of the Unexpected The interior fuse box is behind the dashboard on the driver’s side. The interior fuse box label is attached on the back side of the cover. To see the interior fuse box label, remove the cover by pulling it toward you while holding the bottom center part of cover.
Fuses UNDER-HOOD (On the battery) Next to the battery TAB TAB The under-hood fuse is on the positive terminal of the battery. To open it, push the tabs as shown. 370 The under-hood fuse box is located next to the battery. To open it, push the tab as shown.
Fuses Checking and Replacing Fuses If something electrical in your vehicle stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 374 and 375 , or the diagram on the fuse box lid, which fuse or fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works. BLOWN 2.
Fuses BLOWN 5. Look for a blown wire inside the fuse. If it is blown, replace the fuse with one of the spare fuses of the same rating or lower. 372 FUSE PULLER The fuse puller is in the interior fuse box. If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).
Fuses Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating. Taking Care of the Unexpected 6. If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem with your vehicle. Leave the blown fuse in that circuit, and have your vehicle checked by a qualified technician.
Fuse Locations INTERIOR FUSE BOX 374 No. Amps. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 15 A (7.5 A) 20 A − 10 A 10 A 10 A 7.5 A − 7.5 A 7.5 A 10 A 20 A 7.5 A 7.5 A 10 A 20 A 18 20 A 19 20 A 20 21 22 15 A 15 A 7.
Fuse Locations No. Amps. 60 7.5 A − 30 A 10 A 15 A 15 A 10 A 15 A 10 A − 10 A 30 A 30 A 30 A 30 A 40 A − 50 A Circuits Protected Hatch Lock Not Used Condenser Fan Motor Left Headlight High Beam Door Lock Motor 2 (Unlock) Door Lock Motor 1 (Unlock) Right Headlight High Beam DBW IMA 2 Not Used Heated Mirror＊2, ＊3 Front Wiper Blower Motor ABS/VSA Motor Rear Defogger＊1 Rear Defogger＊2, ＊3 Not Used IG Main UNDER-HOOD FUSE BOXES On the battery No. Amps.
Emergency Towing If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous. There are two ways to tow your vehicle: Flat-bed Equipment − The operator loads your vehicle on the back of a truck. This is the best way to transport your vehicle. Wheel-lift Equipment − The tow truck uses two pivoting arms that go under the tires (front) and lift them off the ground. The other two tires remain on the ground.
Emergency Towing, If Your Vehicle Gets Stuck Trying to lif t or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight. The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (I) position, and make sure the steering wheel turns f reely bef ore you begin towing.
If Your Vehicle Gets Stuck WHEEL NUT WRENCH 3. Screw the towing hook into the hole, and tighten it with the wheel nut wrench. To avoid damage to your vehicle, use the towing hook f or straight, f lat ground towing only. Do not tow at an angle. The tow hook should not be used to tow the vehicle onto a f lat bed. Do not use it as a tie down.
Technical Information The diagrams in this section give you the dimensions and capacities of your vehicle and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Identification Numbers ................. 380 Specifications ................................. 382 DOT Tire Quality Grading (U.S. Vehicles) ....................... 384 Uniform Tire Quality Grading ................................... 384 Treadwear .......
Identification Numbers Your vehicle has several identifying numbers in various places. The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
Identification Numbers The engine number is stamped into the engine block. The transmission number is on a label on top of the transmission. The IMA Motor Number is stamped on the motor housing.
Specifications Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating Seating Capacities Total Front Rear Engine Type Bore x Stroke Displacement Compression ratio Spark plugs 382 172.3 in (4,377 mm) 66.7 in (1,695 mm) 56.2 in (1,427 mm) 100.4 in (2,550 mm) 58.3 in (1,481 mm) 58.0 in (1,472 mm) See the certification label attached to the driver’s doorjamb. 5 2 3 Water cooled 4-stroke SOHC i-VTEC gasoline engine with Hybrid Electric Motor 2.87 x 3.15 in (73.
Specifications Air Conditioning Refrigerant type Charge quantity Lubricant oil type Lights Headlights 12 Volt Battery Capacity Fuses Interior 12 V − 60 W (HB3) 12 V − 55 W (H11) 12 V − 21 W (Amber) 12 V − 5 W 12 V − 5 W LED type＊2 12 V − 21 W (Amber) LED type＊2 12 V − 16 W 12 V − 2 CP 12 V − 5 W 12 V − 8 W 12 V − 8 W 12 V − 5 W LED type＊2 12 V − 3.4 W See page 374 or the fuse label attached to the inside of the fuse box door under the steering column. See page 375 or the fuse box cover.
DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
DOT Tire Quality Grading (U.S. Vehicles), Tire Labeling Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Tire Labeling The tires that came on your vehicle have a number of markings. Those you should be aware of are described below.
Tire Labeling Tire Size Whenever tires are replaced, they should be replaced with tires of the same size. Following is an example of tire size with an explanation of what each component means. 84 − Load index (a numerical code associated with the maximum load the tire can carry). T − Speed symbol (an alphabetical code indicating the maximum speed rating). 2KNR − Tire type code. 2202 − Date of manufacture.
Tire Labeling, Tire Pressure Monitoring System (TPMS) − Required Federal Explanation Maximum Load Rating − Means the load rating for a tire at the maximum permissible inflation pressure for that tire. Recommended Inflation Pressure − The cold tire inflation pressure recommended by the manufacturer. Treadwear Indicators (TWI) − Means the projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread.
Tire Pressure Monitoring System (TPMS) − Required Federal Explanation Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
Emissions Controls The burning of gasoline in your vehicle’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.’’ Carbon monoxide does not contribute to smog creation, but it is a poisonous gas.
Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, ignition timing control, exhaust gas recirculation, and three way catalytic converter. These four systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that come out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Emissions Testing Testing of Readiness Codes If you take your vehicle for an emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the onboard diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Emissions Testing 7. Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway in D. Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
394
Warranty and Customer Relations Customer Service Information..... 396 Warranty Coverages ..................... 397 Reporting Safety Defects.............. 398 Authorized Manuals ......................
Customer Service Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The service manager or general manager can help. Almost all problems are solved in this way. Canadian Owners: If you are dissatisfied with the decision made by the dealership’s management, contact Honda Customer Service.
Warranty Coverages U.S. Owners Your new vehicle is covered by these warranties: Emissions Control Systems Defects Warranty and Emissions Performance Warranty − these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional. Please read your warranty booklet for exact information. Rust Perforation Limited Warranty − all exterior body panels are covered for rust-through from the inside for the specified time period with no mileage limit.
Reporting Safety Defects In the US If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying American Honda Motor Co., Inc. In Canada If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Honda Canada Inc. and you may also inform Transport Canada.
Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The publications shown below can be purchased from Helm Incorporated. You can order by phone or online: Call Helm Inc. at 1-800-782-4356 (credit card orders only) Go online at www.helminc.com If you are interested in other years or models, contact Helm Inc. at 1-800-782-4356.
400
Index A Shift Lever Positions ................. 275 Shift Lock Release ..................... 277 Auxiliary Input Jack ....................... 220 B Battery Charging System Indicator............................ 63, 366 Jump Starting ............................. 360 Maintenance ............................... 346 Specifications ............................. 383 Before Driving ............................... 245 Belts, Seat ..................................... 9, 21 Beverage Holder ........................
Index Braking System.............................. 287 Break-in, New Vehicle .................. 246 Brightness Control, Instruments ................................ 124 Bulb Replacement Back-up Lights ........................... 329 Brake Lights............................... 332 Front Side Marker Lights......... 328 Front Turn Signal Lights .......... 327 Headlights .................................. 323 Parking Lights ........................... 326 Rear Turn Signal Lights ........... 329 Specifications .
Index Doors Auto Door Locking .................... 109 Auto Door Unlocking ................ 110 Childproof Door Locks ............. 134 Locking and Unlocking ............. 133 DOT Tire Quality Grading ........... 384 Driver and Passenger Safety ............ 5 Driving ............................................ 263 Economy ..................................... 253 Dust and Pollen Filter ................... 334 E Exhaust Fumes ................................ 56 Expectant Mothers, Use of Seat Belts by ....
Index Fuel .................................................. 246 Fill Door and Cap....................... 247 Gauge ............................................ 73 Octane Requirement ................. 246 Oxygenated ................................ 246 Reserve Indicator......................... 70 Tank, Filling the......................... 247 Fuses, Checking the ...................... 371 G Gas Mileage, Improving................ 253 Gasoline ..........................................
Index Inflation, Recommended Tire ...... 341 Pressures .................................... 341 Information Display ......................... 72 Inside Mirror .................................. 147 Inspection, Tire .............................. 341 Instrument Panel ............................. 61 Instrument Panel Brightness ....... 124 Interior Lights ................................ 161 Introduction ......................................... i iPod ................................................
Index M Maintenance ................................... 299 Main Items and Sub Items ....... 306 Minder......................................... 301 Owner’s Maintenance Checks .................................... 309 Safety........................................... 300 Malfunction Indicator Lamp .. 62, 367 Meters, Gauges.......................... 61, 72 Methanol in Gasoline .................... 246 Mirrors ............................................ 147 Adjusting.....................................
Index Rear Window Defogger ................ 126 Reclining the Seat-backs ............... 141 Recommended Shift Points .......... 282 Remote Audio Controls................. 219 Remote Transmitter ...................... 135 Replacement Information Dust and Pollen Filter ............... 334 Engine Oil and Filter ................. 314 Fuses ........................................... 371 Light Bulbs ................................. 323 Maintenance MinderTM.............. 301 Tires ..............................
Index SRS, Additional Information........... 25 Additional Safety Precautions .... 37 Advanced Airbag System ........... 30 Airbag Service .............................. 36 How the Passenger Airbag Off Indicator Works ....................... 35 How the Side Airbag Off Indicator Works ....................... 34 How the SRS Indicator Works ... 34 How Your Front Airbags Work.......................................... 28 How Your Side Airbags Work.... 32 How Your Side Curtain Airbags Work .......................
Index Tires Snow ............................................ 344 Specifications ............................. 383 Tools, Tire Changing .................... 352 Towing A Trailer ...................................... 298 Emergency Towing ................... 376 Transmission Checking Fluid Level, Automatic ............................... 320 Fluid Selection............................ 321 Identification Number............... 381 Shifting the Automatic .............. 274 Treadwear ............................
11/08/27 15:22:56 31TM8620_417 Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 87 or higher. Fuel Tank Capacity: 10.6 US gal (40 ) Recommended Engine Oil: API Premium grade 0W-20 detergent oil (see page 362 ). Oil change capacity (including filter): 3.4 US qt (3.
