00/08/10 11:51:24 31S5P600_002 Introduction Congratulations! Your selection of a 2001 Honda Civic was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your car so you can refer to it at any time. As you read this manual, you will find information that is preceded by a symbol.
00/08/10 11:51:36 31S5P600_003 A Few Words About Safety Your safety, and the safety of others, is very important. And operating this car safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
00/08/10 11:51:55 31S5P600_004 Contents Turn to the beginning of each section for a complete list of subjects. Your Car at a Glance ................ 2 Driver and Passenger Safety ..... 5 Important information about the proper use and care of your car’s seat belts, an overview of the Supplemental Restraint System, and valuable information on how to protect children with child restraints. Instruments and Controls ......
00/08/10 11:52:02 31S5P600_005 Your Car at a Glance AIRBAGS (P. 10, 47) POWER DOOR LOCK SWITCH (P. 84) AUDIO SYSTEM (P. 116, 128, 140) DIGITAL CLOCK (P. 121, 133, 145) POWER WINDOW SWITCHES (P. 96) FUEL FILL DOOR RELEASE (P. 163) TRUNK RELEASE (P. 88) 2 HOOD RELEASE HANDLE (P. 164) AUTOMATIC TRANSMISSION (P. 180) MANUAL TRANSMISSION (P. 178) HEATING/COOLING CONTROLS (P.
00/08/10 11:52:08 31S5P600_006 Your Car at a Glance HEADLIGHTS/TURN SIGNALS (P. 70, 72) WINDSHIELD WIPERS/WASHERS (P. 72, 73) HAZARD WARNING LIGHTS (P. 74) MOONROOF (P. 98) CRUISE CONTROL MASTER SWITCH (P. 76) MIRROR CONTROLS (P. 99) REAR WINDOW DEFOGGER (P. 74) TILT ADJUSTMENT (P. 75) CRUISE CONTROL SWITCHES (P.
00/08/10 11:52:10 31S5P600_007 4
00/08/10 11:52:15 31S5P600_008 Driver and Passenger Safety This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain infants and children in your car. Important Safety Precautions .......... 6 Your Car’s Safety Features .............. 7 Seat Belts ........................................ 8 Airbags ......................................
00/08/10 11:52:27 31S5P600_009 Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
00/08/10 11:52:35 31S5P600_010 Your Car’s Safety Features (10) (8) (1) (3) (4) Your car is equipped with many features that work together to protect you and your passengers during a crash. (6) (8) (7) (5) (2) (7) (2) (9) Some safety features do not require any action on your part.
00/08/10 11:52:44 31S5P600_011 Your Car’s Safety Features These safety features are designed to reduce the severity of injuries in a crash. However, you and your passengers can’t take full advantage of these safety features unless you remain sitting in a proper position and always wear your seat belts properly. In fact, some safety features can contribute to injuries if they are not used properly.
00/08/10 11:52:53 31S5P600_012 Your Car’s Safety Features Not wearing a seat belt properly increases the chance of serious injury or death in a crash, even if you have airbags. Be sure you and your passengers always wear seat belts and wear them properly. When properly worn, seat belts: Help keep you from being thrown against the inside of the vehicle and against other occupants. Keep you from being thrown out of the vehicle. Help keep you in a good position should the airbags ever deploy.
00/08/10 11:53:04 31S5P600_013 Your Car’s Safety Features the seat belts. Airbags Airbags offer no protection in rear impacts, rollovers, or minor frontal or side collisions. Airbags can pose serious hazards. Your car has a Supplemental Restraint System (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision. Only on models equipped with side airbags.
00/08/10 11:53:13 31S5P600_014 Your Car’s Safety Features Seats & Seat-Backs Your car’s seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
00/08/10 11:53:25 31S5P600_015 Your Car’s Safety Features Pre-Drive Safety Checklist To make sure you and your passengers get the maximum protection from your car’s safety features, check the following each time before you drive away: All adults, and children who have outgrown child safety seats, are wearing their seat belts and wearing them properly (see page 16 ). Any infant or small child is properly restrained in a child seat in the back seat (see page 21 ).
00/08/10 11:53:36 31S5P600_016 Protecting Adults Introduction The following pages provide instructions on how to properly protect the driver and other adult occupants. These instructions also apply to children who have outgrown child seats and are large enough to wear lap/shoulder belts. (See page 37 for important additional guidelines on how to properly protect larger children.) 1.Close and Lock the Doors After everyone has entered the car, be sure the doors are closed and locked. 2.
00/08/10 11:53:46 31S5P600_017 Protecting Adults To reduce the chance of injury, wear your seat belt properly, sit upright with your back against the seat, and move the seat as far back as possible from the steering wheel while still maintaining full control of the car. Also make sure your front seat passenger moves the seat as far to the rear as possible. Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate.
00/08/10 15:22:43 31S5P600_018 Protecting Adults Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant’s chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury. Reclining the seat-back too far can result in serious injury or death in a crash.
00/08/10 11:54:04 31S5P600_019 Protecting Adults spreads the forces of a crash over the strongest bones in your upper body. 5.Fasten and Position the Seat Belts Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Also check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash. Improperly positioning the seat belts can cause serious injury or death in a crash.
00/08/10 11:54:14 31S5P600_020 Protecting Adults If a seat belt does not seem to work as it should, it may not protect the occupant in a crash. No one should 6.Adjust the Steering Wheel sit in a seat with an inoperative seat belt. Anyone using a seat belt that is not working properly can be seriously injured or killed. Have your Honda dealer check the belt as soon as possible. Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back.
00/08/10 11:54:21 31S5P600_021 Protecting Adults 7.Maintain a Proper Sitting Position After all occupants have adjusted their seats and put on seat belts, it is very important that they continue to sit upright, well back in their seats, with their feet on the floor, until the car is parked and the engine is off. Sitting improperly can increase the chance of injury during a crash.
00/08/10 11:54:32 31S5P600_022 Protecting Adults Advice for Pregnant Women Pregnant women should also sit upright and as far back as possible from the steering wheel or dashboard. This will reduce the risk of injuries to both the mother and her unborn child that can be caused by a crash or an inflating airbag. Each time you have a check-up, ask your doctor if it’s okay for you to drive. Additional Safety Precautions Two people should never use the same seat belt.
00/08/10 11:54:38 31S5P600_023 Protecting Adults Do not place hard or sharp objects between yourself and a front airbag. Carrying hard or sharp On models with side airbags, do not attach hard objects on or near a front door. If a side airbag objects on your lap, or driving with a pipe or other sharp object in your mouth, can result in injuries if your front airbag inflates. inflates, a cup holder or other hard object attached on or near the door could be propelled inside the car and hurt someone.
00/08/10 11:54:49 31S5P600_024 Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
00/08/10 11:55:00 31S5P600_025 Protecting Children Additional Precautions to Parents Never hold an infant or child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child. If you are wearing a seat belt, the child can be torn from your arms during a crash. For example, if your car crashes into a parked vehicle at 30 mph (48 km/h), a 20-lb (9 kg) infant will become a 600-lb (275 kg) force, and you will not be able to hold on.
00/08/10 11:55:12 31S5P600_026 Protecting Children Small Children Placing a forward-facing child seat in the front seat of a vehicle equipped with a passenger’s front airbag can be hazardous. If the vehicle seat is too far forward, or the child’s head is thrown forward during a collision, an inflating front airbag can strike the child with enough force to kill or very seriously injure a small child. U.S.
00/08/10 11:55:28 31S5P600_027 Protecting Children Canadian Models To remind you of the front airbag hazards, your car has warning labels on the driver’s and front passenger’s visors. Please read and follow the instructions on these labels. If You Must Drive with Several Children Your car has three seating positions in the back seat where children can be properly restrained.
00/08/10 15:22:49 31S5P600_028 Protecting Children Additional Safety Precautions Do not leave children alone in your vehicle. Leaving children without adult supervision is illegal in most states and Canadian provinces, and can be very hazardous. For example, infants and small children left in a vehicle on a hot day can die from heatstroke. And children left alone with the key in the ignition can accidentally set the vehicle in motion, possibly injuring themselves or others.
00/08/10 11:55:43 31S5P600_029 Protecting Children General Guidelines for Using Child Seats The following pages give general guidelines for selecting and installing child seats for infants and small children. Selecting a Child Seat To provide proper protection, a child seat should meet three requirements: 1. The child seat should meet safety standards. The child seat should meet Federal Motor Vehicle Safety Standard 213 (FMVSS 213) or Canadian Motor Vehicle Safety Standard 213 (CMVSS 213).
00/08/10 11:55:52 31S5P600_030 Protecting Children Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all vehicle seating positions. Before purchasing a child seat, we recommend that parents test the child seat in the specific vehicle seating position (or positions) where they intend to use the seat. If a previously purchased child seat does not fit, you may need to buy a different one that will fit.
00/08/10 15:23:02 31S5P600_031 Protecting Children Placing a Child Seat This page briefly summarizes Honda’s recommendations on where to place rear-facing and forwardfacing child seats in your car. Airbags Pose Serious Risks to Children The passenger’s front airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
00/08/10 11:56:15 31S5P600_032 Protecting Children Installing a Child Seat After selecting a proper child seat, and a good position to install the seat, there are three main steps in installing the seat: 1. Properly secure the child seat to the car. All child seats are designed to be secured to the car with the lap part of a lap/shoulder belt. Some child seats can be secured to the vehicle’s lower anchorages instead. A child whose seat is not properly secured to the car can be endangered in a crash.
00/08/10 11:56:26 31S5P600_033 Protecting Children Protecting Infants Rear-Facing Child Seat Placement Placing a rear-facing child seat in the front seat can result in serious injury or death if the passenger’s front airbag inflates. Always place a rear-facing child seat in the back seat, not the front. Child Seat Type Only a rear-facing child seat provides proper support for a baby’s head, neck, and back. Infants up to about one year of age must be restrained in a rear-facing child seat.
00/08/10 11:56:36 31S5P600_034 Protecting Children When properly installed, a rearfacing child seat may prevent the driver or a front-seat passenger from moving the seat as far back as recommended (see page 13 ). Or it may prevent them from locking the seat-back in the desired upright position (see page 14 ). In either case, we recommend that you place the child seat directly behind the front passenger seat, move the front seat as far forward as needed, and leave it unoccupied.
00/08/10 11:56:44 31S5P600_035 Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. 32 Driver and Passenger Safety 4.
00/08/10 11:56:50 31S5P600_036 Protecting Children To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. Rear-Facing Child Seat Installation Tips For proper protection, an infant must ride in a reclined, or semi-reclined position. To determine the proper reclining angle, check with the baby’s doctor or follow the seat maker’s recommendations.
00/08/10 11:56:59 31S5P600_037 Protecting Children Protecting Small Children Of the different seats available, we recommend those that have a fivepoint harness system as shown. We also recommend that a small child stay in the child seat as long as possible, until the child reaches the weight or height limit for the seat.
00/08/10 11:57:09 31S5P600_038 Protecting Children Child Seat Installation Improperly placing a forwardfacing child seat in the front seat can result in serious injury or death if the front airbags inflate. If you must place a forwardfacing child seat in front, move the vehicle seat as far back as possible and properly restrain the child.
00/08/10 11:57:17 31S5P600_039 Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. 36 Driver and Passenger Safety 4.
00/08/10 11:57:25 31S5P600_040 Protecting Children To deactivate the locking mechanism in order to remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in the back seat and wear a lap/shoulder belt.
00/08/10 11:57:34 31S5P600_041 Protecting Children Checking Seat Belt Fit However, if the belt touches or crosses the child’s neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could cause To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt.
00/08/10 11:57:46 31S5P600_042 Protecting Children Using a Booster Seat A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in a back seat.
00/08/10 11:57:57 31S5P600_043 Protecting Children Of course, children vary widely. And while age may be one indicator of when a child can safely ride in the front, there are other important factors you should consider. Physical Size Physically, a child must be large enough for the lap/shoulder belt to properly fit over the hips, chest, and shoulder (see pages 16 and 38 ). If the seat belt does not fit properly, the child should not sit in the front.
00/08/10 11:58:05 31S5P600_044 Protecting Children Attach the tether strap hook to the tether anchorage point and tighten the strap according to the child seat maker’s instructions. Using Child Seats with Tethers ANCHORAGE POINT COVER Your car has three tether anchorage points under the rear window for securing a tether-style child seat to the car. To use the anchorage point, pivot its cover up.
00/08/10 11:58:15 31S5P600_045 Protecting Children Using the Lower Anchorages To install a child seat designed to attach to the lower anchorages: 1. Move the seat belt buckle or center seat belt away from the anchorages. LOWER ANCHORAGES Your car is equipped with lower anchorages at the outer rear seats. These anchorages are located between the seat-back and seat bottom and are only to be used with a child seat designed to attach to the lower anchorages.
00/08/10 11:58:22 31S5P600_046 Protecting Children Flexible type 4. Follow the child seat maker’s instructions for any additional advice on adjusting or tightening the fit. 5. Attach the tether strap hook to the tether anchorage point and tighten the strap according to the child seat maker’s instructions. 6. Push and pull the child seat forward and from side to side to verify that it is secure enough to stay upright during normal driving maneuvers.
00/08/10 11:58:33 31S5P600_047 Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your belts. If the driver’s seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
00/08/10 11:58:42 31S5P600_048 Additional Information About Your Seat Belts If the shoulder part of the belt is pulled all the way out, the locking mechanism will activate. The belt will retract, but it will not allow the passenger to move freely. Automatic Seat Belt Tensioners If your airbags inflate, the tensioners immediately tighten the front seat belts to help hold the occupants in place. The belts will remain tight until you unbuckle them in the normal way.
00/08/10 11:58:50 31S5P600_049 Additional Information About Your Seat Belts The SRS indicator light will come on if there is a problem with your automatic seat belt tensioners (see page 51 ). Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and that the lap/shoulder belts retract easily.
00/08/10 11:58:56 31S5P600_050 Additional Information About Your Seat Belts If a seat belt is worn during a crash, you should have your dealer inspect the belt, and replace it if necessary. A belt that has been worn during a crash may not provide the same level of protection in a subsequent crash. The dealer should also inspect the anchors for damage and replace them if needed. Automatic seat belt tensioners that deployed during a crash must be replaced.
00/08/10 11:59:07 31S5P600_051 Additional Information About Your Airbags SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver’s airbag is stored in the center of the steering wheel; the front passenger’s airbag is stored in the dashboard. Both are marked ‘‘SRS AIRBAG.’’ Automatic seat belt tensioners (see page 45 ). Sensors that can detect a moderate to severe frontal collision.
00/08/10 11:59:16 31S5P600_052 Additional Information About Your Airbags During a frontal crash, your seat belts help restrain your lower body and torso. Your airbag provides a cushion to help restrain and protect your head and chest. The total time for inflation and deflation is approximately one-tenth of a second, so fast that most occupants are not aware that the airbags deployed until they see them lying in their laps.
00/08/10 15:23:14 31S5P600_053 Additional Information About Your Airbags U.S. Owners: For additional information on how your airbags work, see the booklet titled SRS: What You Need to Know About Airbags that came with your owner’s manual. How Your Side Airbags Work Only on models equipped with side airbags. Only one airbag will deploy during a side impact. If the impact is on the passenger’s side, the passenger’s side airbag will deploy even if there is no passenger.
00/08/10 11:59:35 31S5P600_054 Additional Information About Your Airbags How the SRS Indicator Light Works The purpose of the SRS indicator light is to alert you to a potential problem with your front airbags. On cars with side airbags, this light will also alert you to a potential problem with your automatic seat belt tensioners (page 45 ); or your side airbags or passenger’s side airbag automatic cutoff system (page 50 ). When you turn the ignition ON (II), this indicator will light briefly then go out.
00/08/10 11:59:44 31S5P600_055 Additional Information About Your Airbags How The Side Airbag Indicator Light Works Only on models equipped with side airbags This light alerts you that the passenger’s side airbag has been automatically shut off. To reduce the risk of injury from an inflating side airbag, your car has an automatic cutoff system for the passenger’s side airbag.
00/08/10 11:59:54 31S5P600_056 Additional Information About Your Airbags Airbag Service Your front and side airbag systems (if equipped) are virtually maintenance-free, and there are no parts you can safely service. However, you must have your car serviced if: Your airbags ever inflate. Any airbag that has deployed must be replaced along with the seat belt tensioners, control unit and other related parts. Do not try to remove or replace any airbag by yourself.
00/08/10 12:00:03 31S5P600_057 Carbon Monoxide Hazard Your car’s exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside. 54 Driver and Passenger Safety Carbon monoxide gas is toxic.
00/08/10 12:00:21 31S5P600_058 Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. DASHBOARD SUN VISOR U.S. models only U.S. models If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.
00/08/10 12:00:29 31S5P600_059 Safety Labels HOOD On models without side airbags On models with side airbags 56 Driver and Passenger Safety
00/08/10 12:00:35 31S5P600_060 Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach. Control Locations ............................ 58 Indicator Lights................................ 59 Gauges .............................................. 66 Speedometer ................................ 66 Tachometer .................................. 66 Odometer .....................
00/08/10 15:23:21 31S5P600_061 Control Locations MOONROOF (P. 98) MIRROR CONTROLS (P. 99) HEATING/COOLING CONTROLS (P. 108) POWER DOOR LOCK SWITCH (P. 84) CRUISE CONTROL (P. 76) AUDIO SYSTEM (P. 116, 128, 140) DIGITAL CLOCK (P. 119, 131, 143) POWER WINDOW SWITCHES (P. 96) FUEL FILL DOOR RELEASE (P. 163) TRUNK RELEASE (P. 88) 58 Instruments and Controls HOOD RELEASE HANDLE (P. 164) CRUISE CONTROL (P.
00/08/10 15:23:30 31S5P600_062 Indicator Lights U.S.: HX, LX, EX, Canada: LX, Si SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P. 61) TRUNK-OPEN INDICATOR (P. 63) ANTI-LOCK BRAKE SYSTEM INDICATOR*1 (P. 62) SEAT BELT REMINDER LIGHT (P. 61) SIDE AIRBAG INDICATOR (P. 61) IMMOBILIZER SYSTEM INDICATOR (P. 64) CRUISE CONTROL INDICATOR (P. 63) LOW OIL PRESSURE INDICATOR (P. 278) LOW FUEL INDICATOR (P. 63) CHARGING SYSTEM INDICATOR (P. 279) MALFUNCTION INDICATOR LAMP (P. 280) HIGH BEAM INDICATOR (P.
00/08/10 15:23:38 31S5P600_063 Indicator Lights DX TRUNK-OPEN INDICATOR (P. 63) SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P. 61) SEAT BELT REMINDER LIGHT (P. 61) SIDE AIRBAG INDICATOR (P. 61) MAINTENANCE REQUIRED INDICATOR (P. 64) IMMOBILIZER SYSTEM INDICATOR (P. 64) LOW OIL PRESSURE INDICATOR (P. 278) LOW FUEL INDICATOR (P. 63) CHARGING SYSTEM INDICATOR (P. 279) MALFUNCTION INDICATOR LAMP (P. 280) * HIGH BEAM INDICATOR (P. 63) The U.S. instrument panel is shown.
00/08/10 12:01:11 31S5P600_064 Indicator Lights The instrument panel has many indicators to give you important information about your car. Seat Belt Reminder Light This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt. Supplemental Restraint System Indicator This indicator lights when you turn the ignition switch ON (II).
00/08/10 12:01:22 31S5P600_065 Indicator Lights Charging System Indicator If this light comes on when the engine is running, the battery is not being charged. For complete information, see page 279 . Low Oil Pressure Indicator The engine can be severely damaged if this light flashes or stays on when the engine is running. For complete information, see page 278 . Parking Brake and Brake System Indicator This light has two functions: U.S. Canada 1.
00/08/10 15:23:57 31S5P600_066 Indicator Lights Malfunction Indicator Lamp See page 280 . Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 248 ). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling. When you turn on the Hazard Warning switch, both turn signal lights blink.
00/08/10 12:01:49 31S5P600_067 Indicator Lights Immobilizer System Indicator This indicator comes on for a few seconds when you turn the ignition switch ON (II). It will then go off if you have inserted a properly-coded ignition key. If it is not a properlycoded key, the indicator will blink and the engine will not start (see page 80 ). This indicator also blinks several times when you turn the ignition switch from ON (II) to ACCESSORY (I) or LOCK (0).
00/08/10 12:01:56 31S5P600_068 Indicator Lights Your dealer will reset this indicator after completing the scheduled maintenance. If this maintenance is done by someone other than your Honda dealer, reset the indicator as follows. 1. Turn off the engine. 2. Press and hold the select/reset button in the instrument panel, then turn the ignition switch ON (II). 3. Hold the button until the indicator resets (approximately ten seconds).
00/08/10 12:02:07 31S5P600_069 Gauges U.S.: HX, LX, EX, Canada: LX, Si TACHOMETER SPEEDOMETER TEMPERATURE GAUGE FUEL GAUGE ODOMETER/TRIP METER SELECT/RESET BUTTON Speedometer Canadian Models U.S. Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph). This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h).
00/08/10 15:26:29 31S5P600_070 Gauges Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. DX TEMPERATURE GAUGE FUEL GAUGE SPEEDOMETER There are two trip meters: Trip A and Trip B. Switch between these displays and the odometer by pressing the Select/Reset button repeatedly. Each trip meter works independently, so you can keep track of two different distances.
00/08/10 12:02:22 31S5P600_071 Gauges Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom white mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (Hot) mark, pull safely to the side of the road. Turn to page 275 for instructions and precautions on checking the engine’s cooling system.
00/08/10 12:02:30 31S5P600_072 Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. HEADLIGHTS/ TURN SIGNALS MOONROOF HAZARD WARNING LIGHTS WINDSHIELD WIPERS/WASHERS The hazard warning lights switch is on the dashboard between the center air vents.
00/08/10 12:02:39 31S5P600_073 Controls Near the Steering Wheel Headlights The rotating switch on the left lever controls the lights. Turning this switch to the ‘‘ ’’ position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the ‘‘ ’’ position turns on the headlights.
00/08/10 12:02:46 31S5P600_074 Controls Near the Steering Wheel Daytime Running Lights Instrument Panel Brightness Canadian models only With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake. The headlights revert to normal operation when you turn them on with the switch.
00/08/10 12:02:55 31S5P600_075 Controls Near the Steering Wheel Turn Signals Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn. If you push it up or down all the way, the turn signal continues to blink even when you release the lever. It shuts off automatically as you complete the turn. To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it.
00/08/10 12:03:03 31S5P600_076 Controls Near the Steering Wheel In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continuously. Windshield Washers To operate the wipers in mist mode, push the control lever up from the OFF position. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield. To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever.
00/08/10 12:03:12 31S5P600_077 Controls Near the Steering Wheel Hazard Warning Rear Window Defogger Make sure the rear window is clear and you have good visibility before starting to drive. The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side. Push the button between the center vents to turn on the hazard warning lights (four-way flashers).
00/08/10 12:03:23 31S5P600_078 Controls Near the Steering Wheel 3. Push the lever up to lock the steering wheel in that position. Steering Wheel Adjustment See page 17 for important safety information about how to properly position the steering wheel. 4. Make sure you have securely locked the steering wheel in place by trying to move it up and down. Make any steering wheel adjustment before you start driving.
00/08/10 12:03:31 31S5P600_079 Steering Wheel Controls Cruise Control On HX, LX and EX models in the U.S., and LX and Si models in Canada Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions.
00/08/10 12:03:43 31S5P600_080 Steering Wheel Controls RESUME/ accel SET/decel 3. Press and release the SET/decel button on the steering wheel. The CRUISE CONTROL light on the instrument panel comes on to show the system is now activated. The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down to the desired speed. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button.
00/08/10 12:03:54 31S5P600_081 Steering Wheel Controls You can decrease the set cruising speed in any of these ways: Press and hold the SET/decel button. The car will decelerate. Release the button when you reach the desired speed. To slow down in very small amounts, tap the SET/decel button repeatedly. Each time you do this, your car will slow down about 1 mph (1.6 km/h). Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL light on the instrument panel will go out.
00/08/10 12:04:06 31S5P600_082 Steering Wheel Controls, Keys and Locks When you push the CANCEL button, or tap the brake or clutch pedal, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way. The system remembers the previously-set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h), then press the RESUME/accel button.
00/08/10 12:04:16 31S5P600_083 Keys and Locks These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged. Protect the keys from direct sunlight, high temperature, and high humidity. Do not drop the keys or set heavy objects on them. Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth. The keys do not contain batteries. Do not try to take them apart.
00/08/10 12:04:25 31S5P600_084 Keys and Locks The system may not recognize your key’s coding if another immobilizer key or other metal object is near the ignition switch when you insert the key. To make sure the system recognizes the key code: Do not keep other immobilizer keys on the same key ring. Use a plastic or leather key fob, not metal. Keep other keys away from your car’s key and the ignition switch while trying to start the engine.
00/08/10 12:04:33 31S5P600_085 Keys and Locks Ignition Switch The ignition switch is on the right side of the steering column. It has four positions: • LOCK (0) • ACCESSORY (I) • ON (II) • START (III) 82 Instruments and Controls LOCK (0) − You can insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park.
00/08/10 12:04:44 31S5P600_086 Keys and Locks ACCESSORY (I) − In this position, you can operate the audio system and the accessory power socket. ON (II) − This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY to ON. START (III) − Use this position only to start the engine. The switch returns to ON (II) when you let go of the key.
00/08/10 12:04:52 31S5P600_087 Keys and Locks Power Door Locks MASTER DOOR LOCK SWITCH The front doors can be locked and unlocked from the outside with the key. Standard on HX, LX and EX models in the U.S., and LX and Si models in Canada The master door lock switch allows control of both door locks from the driver’s door. Push the switch down to lock both doors, and up to unlock them.
00/08/10 12:05:02 31S5P600_088 Keys and Locks Remote Transmitter LED LOCK BUTTON UNLOCK BUTTON PANIC BUTTON Standard on EX model in the U.S., and Si model in Canada Optional on HX and LX models in the U.S., and on LX in Canada model When you push the LOCK button a second time within 5 seconds after you have locked the doors, the horn will sound once to verify that the doors are locked. When you push the UNLOCK button once, only the driver’s door unlocks.
00/08/10 12:05:14 31S5P600_089 Keys and Locks Panic Mode Replacing the Battery Panic mode allows you to remotely activate your car’s horn and exterior lights to attract attention. When activated, the horn will sound, and the exterior lights will flash, for about 30 seconds. To activate panic mode, press and hold the PANIC button for about one second. To cancel PANIC mode before 30 seconds, press any button on the remote transmitter. You can also turn the ignition switch to ACCESSORY (I) or ON (II).
00/08/10 12:05:24 31S5P600_090 Keys and Locks Reinstall the cushion ring. Align the ▽ mark on the cover with the ◎ mark on the transmitter, then set the cover in place and turn it clockwise. Transmitter Care Avoid severe shock to the transmitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures. Clean the transmitter case with a soft cloth. Do not use strong cleaners or solvents that could harm the case.
00/08/10 12:05:35 31S5P600_091 Keys and Locks Trunk TRUNK RELEASE HANDLE You can open the trunk in two ways: Pull the trunk release handle to the left of the driver’s seat. Use the master key to open the trunk lock. The valet key does not work in this lock. 88 Instruments and Controls MASTER KEY To close the trunk, press down on the trunk lid. See page 171 for cargo loading and weight limit information.
00/08/10 12:05:44 31S5P600_092 Keys and Locks Emergency Trunk Opener U.S. models only Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page 25 . As a safety feature, your car has a release lever on the trunk latch so the trunk can be opened from the inside. To open the trunk, push the release lever to the left.
00/08/10 12:05:52 31S5P600_093 Seat Adjustments Front Seat Adjustments See pages 13 − 15 for important safety information and warnings about how to properly position seats and seat-backs. Make all seat adjustments before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion’s front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
00/08/10 12:06:04 31S5P600_094 Seat Adjustments Driver’s Seat Height Adjustment Driver’s Seat Armrest Rear Seat Access On EX model in the U.S., and Si model in Canada On EX model in the U.S., and Si model in Canada To adjust the height of the driver’s seat, turn the dial on the outside of the seat bottom. To use the driver’s seat armrest, pivot it down. To get into the back seat on the driver’s side, pull up on the seat-back adjustment lever. On HX, EX and LX models in the U.S.
00/08/10 12:06:10 31S5P600_095 Seat Adjustments Push the passenger’s seat-back while pushing down on the release lever to tilt the seat-back out of the way. The entire seat will slide forward at the same time. 92 Instruments and Controls Front Passenger’s Seat with Position Memory On HX model in the U.S., and all Canadian models Adjust the seat-back angle to the desired position with the adjustment lever on the outside of the seat bottom. On EX and LX models in the U.S.
00/08/10 12:06:18 31S5P600_096 Seat Adjustments Head Restraints See page 15 for important safety information and a warning about how to properly position the head restraints. The front head restraints help protect you and your passenger from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint. A taller person should adjust the restraint as high as possible.
00/08/10 12:06:25 31S5P600_097 Folding Rear Seat The back of the rear seat folds down to give you direct access to the trunk. Each side folds down separately. With only half the seat folded, you can still carry a passenger in the back seat. The seat-back can be released from inside the car or inside the trunk. To fold down either side of the seatback from inside the car, insert the master key in the lock on the rear shelf.
00/08/10 12:06:34 31S5P600_098 Folding Rear Seat Make sure all rear shoulder belts are positioned in front of the rear seatback whenever the seat-back is in its upright position. Do not put any heavy items on the seat-back when it is folded. RELEASE Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard. See Carrying Cargo on page 171 .
00/08/10 12:06:41 31S5P600_099 Power Windows On LX and EX models in the U.S., and LX and Si models in Canada Your car’s windows are electricallypowered. Turn the ignition switch to ON (II) to raise or lower any window. Closing a power window on someone’s hands or fingers can cause serious injury. Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop.
00/08/10 12:06:48 31S5P600_100 Power Windows The master control panel also contains these extra features: AUTO − To open the driver’s window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly. The MAIN switch controls power to the passengers’ windows. With this switch off, the passengers’ windows cannot be raised or lowered.
00/08/10 12:06:55 31S5P600_101 Moonroof To lift the rear of the moonroof for ventilation, push the button. To slide the moonroof back, push the switch. Hold it until the moonroof reaches the desired position, then release the switch. To close the moonroof, press and hold the switch. On EX model in the U.S., and Si model in Canada Opening or closing the moonroof on someone’s hands or fingers can cause serious injury. Use the switches on the dashboard under the left vent to operate the moonroof.
00/08/10 12:07:07 31S5P600_102 Mirrors Adjusting the Power Mirrors SELECTOR SWITCH ADJUSTMENT SWITCH TAB Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position. On HX, LX and EX models in the U.S.
00/08/10 12:07:14 31S5P600_103 Mirrors, Parking Brake Parking Brake Driving the car with the parking brake applied can damage the rear brakes and axles. PARKING BRAKE LEVER On Canadian Si model The outside mirrors are heated to remove fog and frost. With the ignition switch ON (II), turn on the heaters by pressing the button. The light in the button comes on as a reminder. Press the button again to turn the heaters off. 100 Instruments and Controls To apply the parking brake, pull the lever up fully.
00/08/10 12:07:20 31S5P600_104 Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. Open the glove box by squeezing the handle. Close it with a firm push.
00/08/10 12:07:29 31S5P600_105 Beverage Holder, Console Compartment Beverage Holder Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior. 102 Instruments and Controls Console Compartment On EX model in U.S. A beverage holder for rear seat passengers is in the back of the console. To use it, pivot the lid down. On EX model in the U.S.
00/08/10 12:07:39 31S5P600_106 Coin Box, Center Pocket, Accessory Power Socket Coin Box Center Pocket Accessory Power Socket The coin box is located under the air vent. To open the coin box, pull the bottom edge. Close it with a firm push. On EX model in the U.S., and LX and Si models in Canada To use the accessory power socket, pull up the cover. The ignition switch must be in ACCESSORY (I) or ON (II). The center pocket is located under the audio system. To open the lid, pull it down.
00/08/10 12:07:49 31S5P600_107 Coat Hook, Cargo Hooks Coat Hook Cargo Hooks To use a coat hook, push on the lid. Close it with a firm push. The hooks on the floor of the cargo area enable you to tie down items stored in the back. Make sure all stored items are secured before driving. Make sure the coat hook is closed when you are not using it. This hook is not designed for large or heavy items. 104 Instruments and Controls Cargo Net On EX models in the U.S.
00/08/10 12:07:57 31S5P600_108 Interior Lights The ceiling light (with the switch in the center position) comes on when you remove the key from the ignition switch. If you do not open a door, the light stays on, then fades out in about 10 seconds. Ceiling Light The ceiling light (with the switch in the center position) also comes on when you unlock the door with the key or the remote transmitter (see page 85 ). The ceiling light has a three-position switch.
00/08/10 12:08:07 31S5P600_109 Interior Lights Spotlights Courtesy Lights LX On EX model in the U.S., and Si model in Canada Turn on the spotlight by pushing the button next to each light. Push the button again to turn it off. You can use the spotlights at all times. 106 Instruments and Controls On LX model On EX model in the U.S. Turn on the spotlight by pushing the lens. Push the lens again to turn it off. You can use the spotlights at all times.
00/08/10 12:08:13 31S5P600_110 Comfort and Convenience Features The heating and air conditioning* systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) * Air conditioning is standard on LX and EX models in the U.S., and LX model in Canada.
00/08/10 12:08:27 31S5P600_111 Heating and Cooling Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. If your car does not have air conditioning, it can be installed at any time. Your dealer can install a Genuine Honda air conditioning system that meets Honda’s high quality standards and is designed to exactly fit your car. Please contact your dealer for more information.
00/08/10 12:08:38 31S5P600_112 Heating and Cooling Mode Control Dial Use the MODE control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. Air flows from the floor vents. Air flow is divided between the floor vents and the defroster vents at the base of the windshield.
00/08/10 12:08:49 31S5P600_113 Heating and Cooling Vent Controls CENTER VENT SIDE VENT Open You can adjust the direction of the air coming from the dashboard vents by moving the tab in the center of each vent up-and-down and side-toside. 110 Comfort and Convenience Features How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting.
00/08/10 12:08:58 31S5P600_114 Heating and Cooling It is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears. The outside air intakes for the heating and cooling system are at the base of the windshield.
00/08/10 12:09:08 31S5P600_115 Heating and Cooling To Cool with A/C 1. Turn on the A/C by pressing the button. The light in the button comes on when a fan speed is selected. 2. Make sure the temperature control dial is all the way to the left. . 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.
00/08/10 12:09:19 31S5P600_116 Heating and Cooling To Heat To warm the interior: 1. Start the engine. and Fresh Air mode. 2. Select 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with the temperature control dial. To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Switch the fan on. 2. Turn on the air conditioning. and Fresh Air mode. 3. Select 4.
00/08/10 12:09:26 31S5P600_117 Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: 1. Start the engine. . 2. Select When you select , the system automatically switches to Fresh Air mode and turns on the A/C. 3. Switch the fan and temperature controls to maximum.
00/08/10 12:09:33 31S5P600_118 Heating and Cooling These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial beside each vent. This will send more warm air to the windshield defroster vents. For safety, make sure you have a clear view through all the windows before driving away.
00/08/10 12:09:41 31S5P600_119 Audio System AM/FM Stereo Audio System STEREO INDICATOR For DX model Your Honda’s audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pressing the PWR/ VOL knob or the AM/FM button. Adjust the volume by turning the knob.
00/08/10 12:09:49 31S5P600_120 Audio System You can use any of five methods to find radio stations on the selected band: TUNE, SEEK, SCAN, AUTO SELECT, and the Preset buttons. TUNE − Use the TUNE knob to tune the radio to a desired frequency. Turn the knob clockwise to tune to a higher frequency, or counterclockwise to tune to a lower frequency. To change the frequency rapidly, press and hold the top or bottom of the SEEK bar. Release the bar when the display reaches the desired frequency.
00/08/10 12:10:00 31S5P600_121 Audio System Preset − You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. STEREO INDICATOR AM/FM BUTTON SCAN INDICATOR AUTO SELECT BUTTON SCAN BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. PRESET BUTTONS PWR/VOL KNOB 2.
00/08/10 12:10:09 31S5P600_122 Audio System AUTO SELECT − If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will appear in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
00/08/10 12:10:20 31S5P600_123 Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the TUNE knob. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the TUNE knob. Balance/Fader − These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength.
00/08/10 12:10:32 31S5P600_124 Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 71 ). The audio system illuminates when the parking lights are on, even if the radio is turned off. Digital Clock The audio system also displays the time. To set the time, the ignition switch must be in ACCESSORY (I) or ON (II), and you must wait about five seconds after performing any other operations with the system.
00/08/10 12:10:41 31S5P600_125 Audio System Operating the Optional Cassette Player The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
00/08/10 12:10:50 31S5P600_126 Audio System Tape Search Functions With a cassette playing, you can use the FF, REW, SKIP, or REPEAT function to find a desired program. FF/REW − Fast Forward and Rewind move the tape rapidly. To rewind the tape, push the REW button. You will see REW in the display. To fast forward the tape, push the FF button. You will see FF displayed. Press the PLAY button to take the system out of rewind or fast forward.
00/08/10 12:10:58 31S5P600_127 Audio System REPEAT − The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
00/08/10 12:11:08 31S5P600_128 Audio System Operating the Optional CD Player/Changer A trunk-mounted Compact Disc changer is available through your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio. CD/TAPE BUTTON AM/FM BUTTON RANDOM INDICATOR REPEAT INDICATOR RANDOM BUTTON REPEAT BUTTON Your dealer also has an accessory indash single CD player available that is operated by the radio controls.
00/08/10 12:11:19 31S5P600_129 Audio System CD Player Insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way. Push the CD/TAPE button and the disc will start to play. You will see the track number being played in the display. You can also play 3-inch (8-cm) discs without using an adapter ring. In all cases, play only standard round discs. Odd-shaped CDs may jam in the drive or cause other problems.
00/08/10 12:11:32 31S5P600_130 Audio System CD Player and Changer You can use the SEEK/SKIP bar to select tracks within a disc. If you press and release the SEEK/SKIP bar, the system will move to the beginning of a track. Press the side to move to the beginning of the next track, and the side to move to the beginning of the current track. If you push and hold the SEEK/ SKIP bar, the system will continue to move across tracks. Release the bar when you think it has reached the desired place on the disc.
00/08/10 12:11:42 31S5P600_131 Audio System AM/FM/Cassette Stereo Audio System For HX and LX models in the U.S. STEREO INDICATOR SCAN INDICATOR AM/FM BUTTON Your Honda’s audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play.
00/08/10 12:11:51 31S5P600_132 Audio System You can use any of five methods to find radio stations on the selected band: TUNE, SEEK, SCAN, AUTO SELECT, and the Preset buttons. TUNE − Use the TUNE knob to tune the radio to a desired frequency. Turn the knob clockwise to tune to a higher frequency, or counterclockwise to tune to a lower frequency. To change the frequency rapidly, press and hold the top or bottom of the SEEK bar. Release the bar when the display reaches the desired frequency.
00/08/10 12:12:02 31S5P600_133 Audio System Preset − You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. STEREO INDICATOR SCAN INDICATOR AM/FM BUTTON AUTO SELECT BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. PWR/VOL KNOB PRESET BUTTONS SEEK BAR 2.
00/08/10 12:12:11 31S5P600_134 Audio System AUTO SELECT − If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will appear in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
00/08/10 12:12:22 31S5P600_135 Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the TUNE knob. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the TUNE knob. Balance/Fader − These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength.
00/08/10 12:12:34 31S5P600_136 Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 71 ). The audio system illuminates when the parking lights are on, even if the radio is turned off. Digital Clock The audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II).
00/08/10 12:12:44 31S5P600_137 Audio System You can quickly set the time to the nearest hour. If the displayed time is before the half hour, the clock is set back to the previous hour by pressing and holding the CLOCK button, then pressing the RESET (Preset 6) button. If the displayed time is after the half hour, the clock is set forward to the beginning of the next hour.
00/08/10 12:12:53 31S5P600_138 Audio System Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the button. When the system reaches the end of the tape, it will automatically reverse direction and play the other side. If you want to remove the cassette from the drive, press the EJECT button.
00/08/10 12:13:02 31S5P600_139 Audio System REPEAT − The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
00/08/10 12:13:11 31S5P600_140 Audio System Operating the Optional CD Player/Changer A trunk-mounted Compact Disc changer is available for your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio and cassette player. AM/FM BUTTON RANDOM INDICATOR REPEAT INDICATOR CD/TAPE BUTTON Your dealer also has an accessory indash single CD player available that is operated by the radio controls.
00/08/10 12:13:22 31S5P600_141 Audio System CD Player Insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way. Push the CD/TAPE button and the disc will start to play. You will see the track number being played in the display. You can also play 3-inch (8-cm) discs without using an adapter ring. In all cases, play only standard round discs. Odd-shaped CDs may jam in the drive or cause other problems.
00/08/10 12:13:35 31S5P600_142 Audio System CD Player and Changer You can use the SEEK/SKIP bar to select tracks within a disc. If you press and release the SEEK/SKIP bar, the system will move to the beginning of a track. Press the side to move to the beginning of the next track, and the side to move to the beginning of the current track. If you push and hold the SEEK/ SKIP bar, the system will continue to move across tracks. Release the bar when you think it has reached the desired place on the disc.
00/08/10 12:13:44 31S5P600_143 Audio System AM/FM/CD Audio System For EX model in the U.S., and LX and Si models in Canada STEREO INDICATOR SCAN INDICATOR AM/FM BUTTON Your Honda’s audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The anti-theft feature will disable the system if it is disconnected from the car’s battery. To get the system working again, you must enter a code number (see page 159 ).
00/08/10 12:13:52 31S5P600_144 Audio System You can use any of five methods to find radio stations on the selected band: TUNE, SEEK, SCAN, AUTO SELECT, and the Preset buttons. TUNE − Use the TUNE knob to tune the radio to a desired frequency. Turn the knob clockwise to tune to a higher frequency, or counterclockwise to tune to a lower frequency. To change the frequency rapidly, press and hold the top or bottom of the SEEK bar. Release the bar when the display reaches the desired frequency.
00/08/10 12:14:03 31S5P600_145 Audio System Preset − You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. AM/FM BUTTON STEREO INDICATOR SCAN INDICATOR AUTO SELECT BUTTON SCAN BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. PWR/VOL KNOB PRESET BUTTONS SEEK BAR 2.
00/08/10 12:14:12 31S5P600_146 Audio System AUTO SELECT − If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
00/08/10 12:14:22 31S5P600_147 Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the TUNE knob. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the TUNE knob. Balance/Fader − These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength.
00/08/10 15:26:41 31S5P600_148 Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 71 ). The audio system illuminates when the parking lights are on, even if the radio is turned off. Digital Clock The display of your audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II).
00/08/10 12:14:44 31S5P600_149 Audio System You can quickly set the time to the nearest hour. If the displayed time is before the half hour, the clock is set back to the previous hour by pressing and holding the CLOCK button, then pressing the RESET (Preset 6) button. If the displayed time is after the half hour, the clock is set forward to the beginning of the next hour. For example: 1:06 would RESET to 1:00. 1:52 would RESET to 2:00.
00/08/10 12:14:52 31S5P600_150 Audio System Radio Reception How well your Honda’s radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions. A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out.
00/08/10 12:14:59 31S5P600_151 Audio System Electrical interference from passing vehicles and stationary sources can cause temporary reception problems. As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills.
00/08/10 12:15:09 31S5P600_152 Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. CD/TAPE BUTTON With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display.
00/08/10 12:15:20 31S5P600_153 Audio System You can switch to the radio while a CD is playing by pressing the AM/ FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off. If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the disc from the drive.
00/08/10 12:15:31 31S5P600_154 Audio System Operating the CD Changer (Optional) A trunk-mounted Compact Disc changer is available for your vehicle. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs.
00/08/10 12:15:40 31S5P600_155 Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. To clean a disc, use a clean soft cloth.
00/08/10 15:26:49 31S5P600_156 Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer. Indication Cause FOCUS Error Mechanical Error High temperature. Solution Press the EJECT button and pull out the disc. Check if the disc is inserted correctly in the CD player. Make sure the disc is not scratched or damaged.
00/08/10 15:27:00 31S5P600_157 Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer. Indication Cause FOCUS Error No CD in the CD magazine Mechanical Error High temperature. No CD magazine in the CD changer.
00/08/10 12:16:09 31S5P600_158 Audio System Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. CD/TAPE BUTTON REPEAT INDICATOR NR INDICATOR AM/FM BUTTON Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.
00/08/10 12:16:19 31S5P600_159 Audio System The tape direction indicator will light to show you which side of the cassette is playing. The ▲ indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button. Dolby noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby noise reduction, turn it off by pressing the NR button. Dolby remains off until you turn it on by pressing the button again.
00/08/10 12:16:25 31S5P600_160 Audio System SKIP − The Skip Function allows you to find the beginning of a song or passage. To find the beginning of the song or passage currently playing, push the lower part of the SKIP bar. You will see REW flashing in the display as the tape rewinds. To find the beginning of the next song, push the upper part of the SKIP bar. You will see FF flashing in the display as the tape fast forwards.
00/08/10 12:16:36 31S5P600_161 Audio System Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available. If you do not clean the cassette player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit. Use 100-minute or shorter cassettes.
00/08/10 12:16:44 31S5P600_162 Audio System Theft Protection For EX model in the U.S., and LX and Si models in Canada Your car’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.
00/08/10 12:16:47 31S5P600_163 160
00/08/10 12:16:52 31S5P600_164 Before Driving Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. Break-in Period .............................. 162 Gasoline ..........................................
00/08/10 12:17:04 31S5P600_165 Break-in Period, Gasoline Break-in Period Help assure your car’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km). Do not change the oil until the recommended time or mileage interval shown in the maintenance schedule.
00/08/10 12:17:15 31S5P600_166 Service Station Procedures Filling the Fuel Tank Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 1. Because the fuel fill cap is on the driver’s side of the car, park with that side closest to the service station pumps. 3. Remove the fuel fill cap slowly.
00/08/10 12:17:24 31S5P600_167 Service Station Procedures 5. Screw the fuel fill cap back on, tighten it until it clicks several times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 280 ). Opening the Hood HOOD RELEASE HANDLE LATCH 6. Push the fuel fill door closed until it latches. 1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
00/08/10 12:17:33 31S5P600_168 Service Station Procedures If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 226 ). After closing the hood, make sure it is securely latched. SUPPORT ROD 3. Pull the support rod out of its clip and insert the end into the hole on the left side of the hood.
00/08/10 12:17:42 31S5P600_169 Service Station Procedures Oil Check DIPSTICK Check the engine oil level every time you fill the car with fuel. Wait a few minutes after turning the engine off before you check the oil. 1. Remove the dipstick (orange handle). 166 Before Driving 2. Wipe the dipstick with a clean cloth or paper towel. 3. Insert it all the way back in its tube.
00/08/10 12:17:51 31S5P600_170 Service Station Procedures Engine Coolant Check MAX UPPER MARK LOWER MARK 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 209 . Refer to Owner Maintenance Checks on page 207 for information on checking other items in your Honda. MIN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines.
00/08/10 12:18:03 31S5P600_171 Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 207 ). For example, an underinflated tire causes more ‘‘rolling resistance,’’ which uses fuel.
00/08/10 12:18:15 31S5P600_172 Accessories and Modifications Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty. Non-Honda accessories are usually designed for universal applications.
00/08/10 12:18:26 31S5P600_173 Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
00/08/10 12:18:33 31S5P600_174 Carrying Cargo CONSOLE COMPARTMENT*1 FRONT DOOR POCKET Your car has several convenient storage areas so you can stow cargo safely. The glove box, and the pockets in the front doors and seat-back, are designed for small, lightweight items. The trunk is intended for larger, heavier items. In addition, the back seat can be folded down to allow you to carry more cargo or longer items.
00/08/10 12:18:45 31S5P600_175 Carrying Cargo Load Limit The maximum load for your car is 850 lbs (395 kg). This figure includes the total weight of all occupants, cargo, and accessories. To figure out how much cargo you can carry: Add up the weight of all occupants. Subtract the total from 850 lbs (395 kg). The final number is the total weight of cargo you can carry. Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed.
00/08/10 12:18:52 31S5P600_176 Carrying Cargo Carrying Cargo in the Trunk or on a Roof Rack Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible. If you can carry any items on a roof rack, be sure the total weight of the rack and the items does not exceed the maximum allowable weight. Please contact your Honda dealer for further information.
00/08/10 12:18:55 31S5P600_177 174
00/08/10 12:19:00 31S5P600_178 Driving This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, and the braking system. Preparing to Drive ......................... 176 Starting the Engine........................ 177 Starting in Cold Weather at High Altitude ..................... 177 5-speed Manual Transmission ..... 178 Recommended Shift Points ......
00/08/10 12:19:13 31S5P600_179 Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and trunk are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. 5.
00/08/10 12:19:28 31S5P600_180 Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
00/08/10 12:19:35 31S5P600_181 5-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’ The manual transmission is synchronized in all forward gears for smooth operation.
00/08/10 12:19:46 31S5P600_182 5-speed Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control.
00/08/10 12:19:55 31S5P600_183 Automatic Transmission Your Honda’s transmission has four forward speeds, and is electronically controlled for smoother shifting. It also has a ‘‘lock-up’’ torque converter for better fuel economy. You may feel what seems like another shift when the converter locks. Shift Lever Position Indicator To operate the HX model’s Continuously Variable Transmission (CVT), refer to page 185 . U.S.
00/08/10 12:20:04 31S5P600_184 Automatic Transmission Shift Lever Positions To shift from: P to R R to P N to R D3 to 2 2 to D3 D3 to D D to N D to D3 N to D R to N The shift lever has six positions. It must be in Park or Neutral to start the engine. When you are stopped in D, D3, 2, N or R, press firmly on the brake pedal, and keep your foot off the accelerator pedal. Do this: Press the brake pedal and press the release button. Press the release button. Move the lever.
00/08/10 12:20:12 31S5P600_185 Automatic Transmission If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 184 . You must also press the release button to shift into Park. To avoid transmission damage, come to a complete stop before shifting into Park. The shift lever must be in Park before you can remove the key from the ignition switch. 182 Driving Reverse (R) − To shift to Reverse from Park, see the explanation under Park.
00/08/10 12:20:20 31S5P600_186 Automatic Transmission Drive (D3) −This position is similar to D4, except only the first three gears are selected. Use D3 to provide engine braking when going down a steep hill. D3 can also keep the transmission from cycling between third and fourth gears in stop-and-go driving. For faster acceleration when in D3 or D4, you can get the transmission to automatically downshift by pushing the accelerator pedal to the floor.
00/08/10 12:20:33 31S5P600_187 Automatic Transmission Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. RELEASE BUTTON 1. Set the Parking brake. 2. Remove the key from the ignition switch. COVER 3. Put a cloth on the edge of the Shift Lock Release slot cover next to the shift lever.
00/08/10 15:27:12 31S5P600_188 Automatic Transmission (CVT) Continuously Variable Transmission (CVT) Shift Lever Position Indicator Shift Lever Positions This indicator on the instrument panel shows which position the shift lever is in. The ‘‘D’’ indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission.
00/08/10 12:20:52 31S5P600_189 Automatic Transmission (CVT) To shift from: P to R R to P N to R S to L L to S S to D D to S D to N N to D R to N Do this: Press the brake pedal and press the release button. Press the release button. Move the lever. Park (P) − This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine.
00/08/10 12:21:03 31S5P600_190 Automatic Transmission (CVT) Reverse (R) − To shift from Reverse to Park, see the explanation under Park. To shift to Reverse from Neutral, come to a complete stop first. Press the release button before shifting into Reverse from Neutral. Neutral (N) − Use Neutral if you need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Always shift to Park position if you need to leave the vehicle for any reason.
00/08/10 12:21:15 31S5P600_191 Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb. If you have a manual transmission, put it in first gear.
00/08/10 12:21:23 31S5P600_192 The Braking System All Civics are equipped with front disc brakes. The brakes on the rear wheels are drum. A power assist helps reduce the effort needed on the brake pedal. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work. It also keeps your brake lights on all the time, confusing drivers behind you.
00/08/10 12:21:33 31S5P600_193 The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Front 190 Driving Anti-lock Brakes The U.S. EX model has an Anti-lock Brake System (ABS) as standard equipment.
00/08/10 12:21:41 31S5P600_194 The Braking System Activation varies with the amount of traction your tires have. On dry pavement, you will need to press on the brake pedal very hard before you activate the ABS. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice. Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking.
00/08/10 12:21:47 31S5P600_195 The Braking System ABS Indicator ABS INDICATOR* * U.S. indicator shown The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 62 ). This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system without antilock, providing normal stopping ability. You should have the dealer inspect your car as soon as possible.
00/08/10 12:21:56 31S5P600_196 Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Technique − Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
00/08/10 12:22:04 31S5P600_197 Driving in Bad Weather, Towing a Trailer Traction − Check your tires frequently for wear and proper pressure. Both are important in preventing ‘‘hydroplaning’’ (loss of traction on a wet surface). In the winter, mount snow tires on all four wheels for the best handling. Watch road conditions carefully, they can change from moment to moment. Wet leaves can be as slippery as ice. ‘‘Clear’’ roads can have patches of ice.
00/08/10 12:22:12 31S5P600_198 Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual.
00/08/10 12:22:18 31S5P600_199 Maintenance Safety Regularly maintaining your car is the best way to protect your investment. Proper maintenance is essential to your safety and the safety of your passengers. It will also reward you with more economical, trouble-free driving and help reduce air pollution. Improperly maintaining this car or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
00/08/10 12:22:27 31S5P600_200 Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts.
00/08/10 12:22:40 31S5P600_201 Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for passengers and their possessions.
00/08/10 12:22:49 31S5P600_202 Maintenance Schedule Driving on muddy, dusty, or deiced roads. NOTE: If you only OCCASIONALLY or NEVER, drive under a ‘‘severe’’ condition, you should follow the Maintenance Schedule for Normal Conditions. Canadian Owners − Follow the Maintenance Schedule for Severe Conditions. Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect.
00/08/10 12:23:08 31S5P600_203 Maintenance Schedule for Normal Conditions Service at the indicated distance or time − whichever comes first.
00/08/10 12:23:20 31S5P600_204 10,000 mil/16,000 km/1 yr 20,000 mil/32,000 km/1 yr 30,000 mil/48,000 km/2 yrs 40,000 mil/64,000 km/2 yrs 50,000 mil/80,000 km/3 yrs 60,000 mil/96,000 km/3 yrs 70,000 mil/112,000 km/4 yrs 80,000 mil/128,000 km/4 yrs 90,000 mil/144,000 km/5 yrs 100,000 mil/160,000 km/5 yrs Every 110,000 mil/176,000 km, otherwise adjust only if noisy 110,000 mil/176,000 km 110,000 mil/176,000 km/6 yrs 110,000 mil/176,000 km/7 yrs 120,000 mil/192,000 km/6 yrs At 120,000 mil/192,000 km or 120 mon
00/08/10 12:23:41 31S5P600_205 Maintenance Schedule for Severe Conditions Service at the indicated distance or time − whichever comes first.
00/08/10 12:23:51 31S5P600_206 Severe Conditions □Replace transmission fluid (MT, AT). Do items in A, B, C, D, E. Do items in A. Do items in A, B. Do items in A, E. Do items in A, B, C. Do items in A. □Replace transmission fluid (AT). Do items in A, B, D, E. A □Replace engine oil. B □Inspect front and rear brakes. □Rotate tires (follow pattern on page 237). □Lubricate all hinges, locks, and latches with multipurpose grease. □Inspect tie rod ends, steering gear box and boots.
Maintenance Schedule for Severe Conditions (listed by distance/time) 00/08/10 12:23:59 31S5P600_207 95,000 mi/152,000 km/5-½ yrs 100,000 mi/160,000 km/5 yrs 100,000 mi/160,000 km/5 yrs 105,000 mi/168,000 km/6 yrs 110,000 mil/176,000 km 110,000 mi/176,000 km/6 yrs 110,000 mi/176,000 km/7 yrs 115,000 mi/184,000 km/6-½ yrs 120,000 mi/192,000 km/6 yrs 120,000 mi/192,000 km/10 yrs 204 Maintenance Do items in A. Do items in A, B, C. □Replace transmission fluid (CVT). Do items in A, E, F.
00/08/10 12:24:08 31S5P600_208 Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 200 ) or severe conditions (page 202 ). Keep the receipts for all work done on your vehicle.
00/08/10 12:24:18 31S5P600_209 Required Maintenance Record (for Normal and Severe Schedules) 65,000 mi 104,000 km Signature or dealer stamp mi/km 95,000 mi 152,000 km mi/km Date 75,000 mi 120,000 km mi/km 100,000 mi 160,000 km (or 5 years) mi/km 105,000 mi 168,000 km mi/km Date 80,000 mi 128,000 km (or 4 years) mi/km 85,000 mi 136,000 km mi/km 110,000 mi 176,000 km Date mi/km Date 206 Maintenance Date Date mi/km Date 115,000 mi 184,000 km Date 90,000 mi 144,000 km mi/km Date Date 70
00/08/10 12:24:27 31S5P600_210 Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level − Check every time you fill the fuel tank. See page 166 . Engine coolant level − Check the radiator reserve tank every time you fill the fuel tank. See page 167 . Windshield washer fluid − Check the level in the reservoir monthly.
00/08/10 12:24:33 31S5P600_211 Fluid Locations ENGINE OIL DIPSTICK (Orange loop) ENGINE OIL FILL CAP BRAKE FLUID (Gray cap) CLUTCH FLUID (Gray cap) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) ENGINE COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP 208 Maintenance AUTOMATIC TRANSMISSION FLUID DIPSTICK (CVT) (Yellow loop)
00/08/10 12:24:43 31S5P600_212 Engine Oil Adding Oil ENGINE OIL FILL CAP To add oil, unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil, and install the engine oil fill cap. Tighten it securely. Wait a few minutes and recheck the oil level. Do not fill above the upper mark; you could damage the engine. Recommended Oil Oil is a major contributor to your engine’s performance and longevity.
00/08/10 12:24:52 31S5P600_213 Engine Oil The SAE number tells you the oil’s viscosity or weight. Select the oil for your vehicle according to this chart. 5W-20 oil is formulated for yearround protection of your Honda, to improve cold weather starting, and to help your engine use less fuel. If 5W-20 oil is not available, a 5W-30 oil may be used. However, it should be replaced with 5W-20 at the next oil change.
00/08/10 12:25:04 31S5P600_214 Engine Oil Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service.
00/08/10 12:25:14 31S5P600_215 Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: (U.S.: DX, LX, Canada: DX, LX) 33 lbf·ft (44 N·m , 4.5 kgf·m) (U.S.: EX) 29 lbf·ft (39 N·m , 4.0 kgf·m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): (U.S.: DX, LX, Canada: DX, LX) 3.4 US qt (3.2 , 2.8 Imp qt) (U.S.: EX, HX) 3.7 US qt (3.5 , 3.1 Imp qt) 212 Maintenance 7. Replace the engine oil fill cap. Start the engine.
00/08/10 12:25:25 31S5P600_216 Cooling System Adding Engine Coolant RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. This coolant should always be a mixture of 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water. Always use Honda All Season Antifreeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water.
00/08/10 12:25:34 31S5P600_217 Cooling System RADIATOR CAP 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3. Remove the radiator cap by pushing down and turning counterclockwise. 214 Maintenance RESERVE TANK 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. 5. Put the radiator cap back on. Tighten it fully. 6. Pour coolant into the reserve tank.
00/08/10 12:25:45 31S5P600_218 Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Honda All Season Antifreeze/ Coolant Type 2. Draining the coolant requires access to the underside of the car. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic. 1. Turn the ignition ON (II).
00/08/10 15:27:26 31S5P600_219 Cooling System NUT BOLT BOLT TAB 9. Reconnect the battery cables to the terminals. Connect the positive (+) cable first, then the negative (−) cable. WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. On U.S. EX and Canadian LX and Si 4. Disconnect the battery cables from the terminals. Disconnect the negative (−) cable first, then the positive (+) cable. 5.
00/08/10 15:27:38 31S5P600_220 Cooling System 10.When the coolant stops draining, tighten the drain plug in the bottom of the radiator. Apply nonhardening sealant to the drain bolt threads, put a new washer on the drain bolt, and reinstall the drain bolt in the engine block. Tighten it securely. Tightening torque: 58 lbf·ft (78 N·m , 8.0 kgf·m) FILLER NECK The cooling system capacity is: With 5-speed manual transmission: 1.03 US gal (3.9 , 0.86 Imp gal) With automatic transmission: 1.00 US gal (3.
00/08/10 12:26:20 31S5P600_221 Cooling System 18. Start the engine and hold it at 1,500 rpm until the radiator fan comes on. Turn off the engine. Check the coolant level in the radiator and add coolant if needed. 12. Start the engine and let it run for about 30 seconds. Then turn off the engine. 13. Check the level in the radiator, add coolant if needed. 19. Install the radiator cap, and tighten it fully. 14. Fill the reserve tank to the MAX mark. Install the reserve tank cap. 20.
00/08/10 12:26:29 31S5P600_222 Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. LEVEL GAUGE The windshield washer reservoir is located behind the driver’s side headlight. Check the reservoir’s fluid level by removing the cap and looking at the level gauge attached to the cap.
00/08/10 12:26:39 31S5P600_223 Transmission Fluid Automatic Transmission DIPSTICK (CVT) UPPER MARK LOWER MARK DIPSTICK Check the fluid level with the engine at normal operating temperature. 1. Park the car on level ground. Shut off the engine. For accurate results, wait at least 60 seconds, and no more than 90 seconds, after shutting off the engine to check the fluid level. 220 Maintenance 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. 3.
00/08/10 12:26:47 31S5P600_224 Transmission Fluid 5. If the level is below the lower mark, add fluid into the filler hole to bring it to the upper mark. Always use Honda ATF-Z1 (Automatic Transmission Fluid). If it is not available, you may use a DEXRON III automatic transmission fluid as a temporary replacement. However, continued use can affect shift quality. Have the transmission flushed and refilled with Honda ATF-Z1 as soon as it is convenient. 6.
00/08/10 12:26:56 31S5P600_225 Transmission Fluid 5-speed Manual Transmission FILLER BOLT Correct Level Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.
00/08/10 12:27:07 31S5P600_226 Brake and Clutch Fluid Always use Honda DOT 3 brake fluid. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. However, the use of any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda DOT 3 brake fluid as soon as possible. Brake fluid marked DOT 5 is not compatible with your car’s braking system and can cause extensive damage.
00/08/10 12:27:14 31S5P600_227 Power Steering You should check the fluid level in the power steering reservoir at least once a year. Check the level when the engine is cold. Look at the side of the reservoir. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If it is below the LOWER LEVEL, add power steering fluid to the UPPER LEVEL. UPPER LEVEL Turning the steering wheel to f ull lef t or right lock and holding it there can damage the power steering pump.
00/08/10 12:27:25 31S5P600_228 Air Cleaner Element The air cleaner element should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement BOLTS The air cleaner element is inside the air cleaner housing in the engine compartment. BOLTS To replace it: 1. Loosen the seven bolts and remove the air cleaner housing cover. 2. Remove the old air cleaner element. AIR CLEANER ELEMENT 3. Carefully clean the inside of the air cleaner housing with a damp rag. 4.
00/08/10 12:27:30 31S5P600_229 Hood Latch PIVOTS Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts, including the pivot. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer.
00/08/10 12:27:40 31S5P600_230 Spark Plugs The spark plugs in your car should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement CLIPS 1. Remove the cover by turning the two clips one quarter turn counterclockwise. 2. Clean up any dirt and oil that have collected around the ignition coils. 3. Use a wrench to remove the nut holding the ignition coil. Remove the ignition coil by pulling it straight out. 4.
00/08/10 12:27:48 31S5P600_231 Spark Plugs 5. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket. 228 Maintenance 6. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 7. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 13 lbf·ft (18 N·m , 1.
00/08/10 12:27:58 31S5P600_232 Spark Plugs 8. Install the ignition coil. Reinstall the nut. Tighten the spark plugs caref ully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 9. Push the wire connector onto the ignition coil. Make sure it locks in place. Specifications: NGK: DENSO: PZFR6F-11 PKJ20CR-M11 Spark Plug Gap: 0.04 in (1.1 mm) +−00.1 mm 10.Repeat this procedure for the other three spark plugs. 11.
00/08/10 12:28:06 31S5P600_233 Battery Check the condition of your car’s battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. TEST INDICATOR WINDOW Check the battery condition by looking at the test indicator window on the battery. The label on the battery explains the test indicator’s colors. 230 Maintenance Check the battery terminals for corrosion (a white or yellowish powder).
00/08/10 12:28:14 31S5P600_234 Battery If you need to connect the battery to a charger, disconnect both cables to prevent damage to the car’s electrical system. The battery gives off explosive hydrogen gas during normal operation. If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative (−) cable first and reconnect it last.
00/08/10 12:28:22 31S5P600_235 Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. 232 Maintenance 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
00/08/10 12:28:31 31S5P600_236 Wiper Blades BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Lower the wiper arm down against the windshield. BLADE 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. REINFORCEMENT 4. Examine the new wiper blades.
00/08/10 12:28:39 31S5P600_237 Air Conditioning System On U.S. LX and EX, Canadian LX models Your car’s air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine’s radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency.
00/08/10 12:28:49 31S5P600_238 Air Conditioning Filter On U.S. LX and EX models, and LX model in Canada Replacement HOOKS The air conditioning filter removes pollen and dust that is brought in from the outside through the heating and cooling system. This filter should be replaced every 30,000 miles (48,000 km) under normal conditions.
00/08/10 12:28:56 31S5P600_239 Air Conditioning Filter 4. Install the new filters. Reinstall the cover. AIR CONDITIONING FILTERS 5. Pivot the glove box up into position. Reinstall the hooks into the side panel of the glove box. Close the glove box. 3. Remove the first filter by pulling it straight out of the air conditioning unit. Remove the second filter by sliding it to the left, then pulling it out.
00/08/10 12:29:09 31S5P600_240 Drive Belts, Timing Belt Drive Belts The belts should have the following ‘‘play’’ or deflection. POWER STEERING BELT Compressor belt (On cars with A/C): 0.20−0.30 in (5.0−7.5 mm) Alternator belt (On cars without A/C): 0.22−0.31 in (5.5−8.0 mm) ALTERNATOR BELT Check the condition of the two drive belts. Examine the edges of each belt for cracks or fraying. Check the tension of each belt by pushing on it with your thumb midway between the pulleys. Power steering belt: 0.
00/08/10 12:29:18 31S5P600_241 Tires To safely operate your car, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how and when to check air pressure, how to inspect your tires for damage and wear, and what to do when your tires need to be replaced. Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.
00/08/10 15:27:51 31S5P600_242 Tires You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges. Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. (U.S.
00/08/10 12:29:41 31S5P600_243 Tires Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. INDICATOR LOCATION MARKS You should look for: Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Excessive tread wear.
00/08/10 12:29:49 31S5P600_244 Tires Make sure the installer balances the wheels when you have new tires installed. This increases riding comfort and tire life. Your car’s original tires were dynamic or ‘‘spin’’ balanced at the factory. For best results, have the installer perform a dynamic balance. Improper wheel weights can damage your car’s aluminum wheels. Use only Genuine Honda wheel weights f or balancing.
00/08/10 12:29:57 31S5P600_245 Tires Replacing Tires and Wheels The tires that came with your car were selected to match the performance capabilities of the car while providing the best combination of handling, ride comfort, and long life. You should replace them with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall). Mixing radial and bias-ply tires on your car can reduce its braking ability, traction, and steering accuracy.
00/08/10 12:30:10 31S5P600_246 Tires Wheels and Tires Wheels: (U.S.: DX, LX, Canada: DX, LX) 14 x 5 1/2 JJ (U.S.: EX, Canada: Si) 15 x 6 JJ (U.S.: HX) 14 x 5 V2 JJ Tires: (U.S.: DX, HX, LX, Canada: DX, LX) P185/70R14 87S (U.S.: EX, Canada: Si) P185/65R15 86H Winter Driving Tires that are marked ‘‘M+ S’’ or ‘‘All Season’’ on the sidewall have an all-weather tread design. They should be suitable for most winter driving conditions.
00/08/10 12:30:17 31S5P600_247 Tires Traction Devices Mount traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Install them only on the front tires. Because your Honda has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices. Metal link-type ‘‘chains’’ should not be used. No matter how tight they seem to be installed, they can come into contact with the body and suspension, causing serious damage.
00/08/10 12:30:23 31S5P600_248 Lights Check the operation of your car’s exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car’s visibility and the ability to signal your intentions to other drivers.
00/08/10 15:29:34 31S5P600_249 Lights Check the following: SIDE MARKER LIGHT TURN SIGNAL LIGHT HIGH-MOUNT STOP LIGHT Headlights (low and high beam) Parking lights Taillights Brake lights High-mount stop light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 295 to determine what type of replacement bulb is needed.
00/08/10 12:30:40 31S5P600_250 Lights Headlight Aiming The headlights were properly aimed when your car was new. If you regularly carry heavy items in the trunk, readjustment may be required. Adjustment of the headlights should be performed by a Honda technician or other qualified mechanic. Replacing a Headlight Bulb Your car has halogen headlight bulbs, one on each side. When replacing a bulb, handle it by its steel base and protect the glass from contact with your skin or hard objects.
00/08/10 12:30:52 31S5P600_251 Lights WEATHER SEAL BULB 5. Insert the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place and clip the end into the slot. 6. Install the rubber seal over the back of the headlight assembly. Make sure it is right side up; it is marked ‘‘TOP.’’ CONNECTOR HOLD-DOWN WIRE 2. Remove the electrical connector from the bulb by squeezing the connector on both sides to unlock the tab. Pull the connector straight off. 3.
00/08/10 12:31:03 31S5P600_252 Lights 6. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. HOLDING CLIP 7. Test the lights to make sure the new bulb is working. 8. Put the inner fender cover in place. Install the holding clip. Lock it in place by pushing on the center. 2. Use a flat-tipped screwdriver to remove the holding clip from the inner fender. 4. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise. 3.
00/08/10 12:31:15 31S5P600_253 Lights 4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Replacing Rear Bulbs (in Fenders) 5. Reinstall the socket into the light assembly by turning it clockwise until it locks. 6. Test the lights to make sure the new bulb is working. 7. Reinstall the trunk lining. Make sure it is installed under the edge of the trunk seal. FASTENER 1. Open the trunk.
00/08/10 12:31:27 31S5P600_254 Lights Replacing a High-mount Brake Light Bulb 1. Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 2. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 3. Reinstall the socket. Turn it clockwise until it locks. Make sure the new bulb is working. Replacing a Rear License Plate Bulb 1.
00/08/10 12:31:35 31S5P600_255 Lights 3. Turn on the parking lights and check that the new bulb is working. Replacing the Trunk Light Bulb 4. Reinstall the socket back in place by pushing it in until it latches. 1. Remove the trunk light assembly by using a small flat-tipped screwdriver to pry carefully on the left edge of the assembly. 2. Pull the bulb straight out of the holder. Push the new bulb straight into the holder until it bottoms. 3.
00/08/10 12:31:46 31S5P600_256 Lights Replacing Bulbs in the Interior Lights CEILING LIGHT Although the ceiling light and spotlights come apart the same way, they do not use the same type of bulbs. FRONT CEILING LIGHT SPOTLIGHTS U.S.: EX, Canada: Si LX On LX models Spotlights: Pry on the edge between the lenses. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. Snap the lens back in place. 1.
00/08/10 12:32:00 31S5P600_257 Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Block the rear wheels. If the car is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.
00/08/10 12:32:05 31S5P600_258 Appearance Care Regular cleaning and polishing of your Honda helps to keep it ‘‘new’’ looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 256 Washing ...................................... 256 Waxing ........................................ 257 Paint Touch-up ................
00/08/10 12:32:16 31S5P600_259 Exterior Care Washing Frequent washing helps preserve your car’s beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner’s Manual.
00/08/10 12:32:26 31S5P600_260 Exterior Care Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes − A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc.
00/08/10 12:32:35 31S5P600_261 Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam.
00/08/10 12:32:44 31S5P600_262 Interior Care Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner. Vinyl Remove dirt and dust with a vacuum cleaner.
00/08/10 12:32:52 31S5P600_263 Interior Care Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces. The rear window def ogger and antenna wires are bonded to the inside of the glass. Wiping vigorously up-anddown can dislodge and break these wires.
00/08/10 12:33:02 31S5P600_264 Corrosion Protection Two factors normally contribute to causing corrosion in your car: 1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the car stays damp, promoting corrosion in that area. 2. Removal of paint and protective coatings from the exterior and underside of the car. Many corrosion-preventive measures are built into your Honda.
00/08/10 12:33:08 31S5P600_265 Body Repairs Body repairs can affect your car’s resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work. Make sure the repair facility uses genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance.
00/08/10 12:33:13 31S5P600_266 Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 264 Changing a Flat Tire .....................
00/08/10 12:33:24 31S5P600_267 Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put it back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
00/08/10 12:33:34 31S5P600_268 Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. SPARE TIRE TRUNK FLOOR The car can easily roll off the jack, seriously injuring anyone underneath.
00/08/10 12:33:42 31S5P600_269 Changing a Flat Tire JACK JACKING POINTS WHEEL WRENCH 6. Turn the jack’s end bracket counterclockwise to loosen it, then remove the jack. 266 Taking Care of the Unexpected 7. Loosen the four wheel nuts 1/2 turn with the wheel wrench. 8. Find the jacking point nearest the wheel you are removing. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point.
00/08/10 12:33:51 31S5P600_270 Changing a Flat Tire WHEEL NUTS WHEEL WRENCH EXTENSION 9. Use the extension and wheel wrench as shown to raise the car until the flat tire is off the ground. WHEEL NUTS WHEEL COVER 10.Remove the wheel nuts and wheel cover. The wheel cover cannot be removed without first removing the wheel nuts. Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. 11.Remove the flat tire.
00/08/10 12:33:59 31S5P600_271 Changing a Flat Tire BRAKE HUB 12.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully, it may be hot from driving. 268 Taking Care of the Unexpected 13.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. 14.
00/08/10 12:34:10 31S5P600_272 Changing a Flat Tire WING BOLT 15.Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m) 16. On HX model in the U.S., Si model in Canada Remove the center cap before storing the flat tire in the trunk well. SPACER CONE 17.Place the flat tire face down in the spare tire well. 18.
00/08/10 12:34:16 31S5P600_273 Changing a Flat Tire 20.Store the jack in the trunk with the end bracket on the left side. Turn the jack’s end bracket to lock it in place. Store the tool kit. Loose items can fly around the interior in a crash and could seriously injure the occupants. Store the wheel, jack and tools securely before driving. 21.Store the wheel cover in the trunk. Make sure it does not get scratched or damaged. 22.Lower the trunk floor, then close the trunk lid.
00/08/10 12:34:27 31S5P600_274 If Your Engine Won’t Start Diagnosing why your engine won’t start falls into two areas, depending on what you hear when you turn the key to START (III): You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
00/08/10 12:34:36 31S5P600_275 If Your Engine Won’t Start The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to START (III), but the engine does not run. Your car has the Immobilizer System. You should use a properly-coded master or valet key to start the engine (see page 80 ). A key that is not properly coded will cause the immobilizer system indicator in the dash panel to blink rapidly.
00/08/10 12:34:46 31S5P600_276 Jump Starting If your car’s battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. To jump start your car, follow these directions closely: 1. Open the hood and check the physical condition of the battery (see page 230 ).
00/08/10 12:34:55 31S5P600_277 Jump Starting BOOSTER BATTERY 3. Connect one jumper cable to the positive (+) terminal on your Honda’s battery. Connect the other end to the positive (+) terminal on the booster battery. 4. Connect the second jumper cable to the negative (−) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. 5.
00/08/10 12:35:04 31S5P600_278 Jump Starting, If Your Engine Overheats 7. Once your car is running, disconnect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery. Keep the ends of the jumper cables away from each other and any metal on the car until all are disconnected. Otherwise, you may cause an electrical short.
00/08/10 12:35:13 31S5P600_279 If Your Engine Overheats 1. Safely pull to the side of the road. Put the transmission in Neutral or Park and set the parking brake. Turn off the heating and cooling system and all other accessories. Turn on the hazard warning indicators. 2. If you see steam and/or spray coming from under the hood, turn off the engine. 3. If you do not see steam or spray, leave the engine running and watch the temperature gauge.
00/08/10 12:35:22 31S5P600_280 If Your Engine Overheats 8. If there was no coolant in the reserve tank, you may also have to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the temperature gauge, or lower, before checking the radiator. Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator cap. 9.
00/08/10 12:35:31 31S5P600_281 Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the car stopped. 1. Safely pull off the road and shut off the engine. Turn on the hazard warning indicators. This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running.
00/08/10 12:35:37 31S5P600_282 Charging System Indicator CHARGING SYSTEM INDICATOR Immediately turn off all electrical accessories: radio, heater, A/C, rear defogger, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly.
00/08/10 12:35:45 31S5P600_283 Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP This indicator should light when the ignition switch is ON (II), and go out after the engine starts. If it comes on at any other time, it indicates one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your car’s performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
00/08/10 12:35:51 31S5P600_284 Malfunction Indicator Lamp Readiness Codes Your car has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed. If your car’s battery has been disconnected or gone dead, these codes are erased. It takes several days of driving under various conditions to set the codes again.
00/08/10 12:36:00 31S5P600_285 Brake System Indicator BRAKE SYSTEM INDICATOR* * U.S. indicator shown The Brake System Indicator normally comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. It comes on and stays lit if you do not fully release the parking brake. 282 Taking Care of the Unexpected If it comes on at any other time, it indicates a problem with the car’s brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir.
00/08/10 12:36:10 31S5P600_286 Closing the Moonroof If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 285 ). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the trunk. 4.
00/08/10 12:36:17 31S5P600_287 Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in two fuse boxes. UNDER-HOOD INTERIOR TAB The under-hood fuse box is located in the engine compartment on the passenger’s side. To open it, push the tabs as shown. 284 Taking Care of the Unexpected The interior fuse box is underneath the steering column. To open it, turn the knobs as shown.
00/08/10 12:36:28 31S5P600_288 Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 287 and 288 , or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component’s operation. 1. Turn the ignition switch to LOCK (0).
00/08/10 12:36:37 31S5P600_289 Fuses BLOWN 5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower. If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).
00/08/10 12:36:44 31S5P600_290 Fuses UNDER-HOOD FUSE BOX No. Amps. 1 20 A 2 15 A 3 7.
00/08/10 12:36:52 31S5P600_291 Fuses INTERIOR FUSE BOX No. Amps. No. Amps. 1 2 3 4 5 15 A 20 A 10 A 10 A − 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Circuits Protected Ignition Coil LAF Heater Daytime running lights* Alternator Not Used * 288 Taking Care of the Unexpected 7.5 A 20 A 7.5 A − 7.5 A 7.5 A 7.5 A 10 A 10 A − − 15 A 15 A 7.
00/08/10 12:37:03 31S5P600_292 Emergency Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. There are three popular types of professional towing equipment. Flat-bed Equipment − The operator loads your car on the back of a truck. This is the best way to transport your Honda.
00/08/10 12:37:10 31S5P600_293 Emergency Towing With the front wheels on the ground, it is best to tow the car no farther than 50 miles (80 km), and keep the speed below 35 mph (55 km/h). If your car is equipped with a front spoiler, remove it before towing so it is not damaged. If you decide to tow your car with all four wheels on the ground, make sure you use a properly-designed and attached tow bar.
00/08/10 12:37:15 31S5P600_294 Technical Information The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Identification Numbers ................. 292 Specifications ................................. 294 DOT Tire Quality Grading (U.S. Cars) .............................. 296 Treadwear ..................................
00/08/10 12:37:21 31S5P600_295 Identification Numbers Your car has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
00/08/10 12:37:27 31S5P600_296 Identification Numbers The Engine Number is stamped into the engine block. The Transmission Number is on a label on top of the transmission.
00/08/10 15:29:55 31S5P600_297 Specifications Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating 174.7 in (4,438 mm) 66.7 in (1,695 mm) 55.1 in (1,399 mm) 103.1 in (2,620 mm) 57.9 in (1,470 mm) 57.9 in (1,470 mm) Capacities Fuel tank Engine coolant See the certification label attached to the driver’s doorjamb. Engine oil Engine Type Bore x Stroke Displacement Compression ratio Spark plugs *1 : U.S.: DX, LX Canada: DX, LX *2 : U.S.
00/08/10 12:38:11 31S5P600_298 Specifications Air Conditioning Refrigerant type Charge quantity Lubricant oil type Lights Headlights (HI/LO) Front turn signal/side marker lights Front parking light Rear turn signal lights Stop/Taillights/Rear side marker lights Back-up lights Taillights High-mount stop light License plate lights Ceiling light Front ceiling light *1 Spotlights Trunk light HFC-134a (R-134a) 17.6−19.
00/08/10 12:38:22 31S5P600_299 DOT Tire Quality Grading (U.S. Cars) The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
00/08/10 12:38:27 31S5P600_300 DOT Tire Quality Grading (U.S. Cars) Temperature − A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
00/08/10 12:38:36 31S5P600_301 Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel’s contents.
00/08/10 12:38:41 31S5P600_302 Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
00/08/10 12:38:51 31S5P600_303 Emissions Controls The burning of gasoline in your car’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.
00/08/10 12:39:04 31S5P600_304 Emissions Controls Onboard Refueling Vapor Recovery The Onboard Refueling Vapor Recovery (ORVR) system captures the fuel vapors during refueling. The vapors are adsorbed in a canister filled with activated carbon. While driving, the fuel vapors are drawn into the engine and burned off. Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, Ignition Timing Control and Three Way Catalytic Converter.
00/08/10 12:39:13 31S5P600_305 Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent. The three way catalytic converter must operate at a high temperature for the chemical reactions to take place.
00/08/10 12:39:24 31S5P600_306 State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not complete the test. This is because of certain ‘‘readiness codes’’ that must be set in the on-board diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
00/08/10 12:39:29 31S5P600_307 State Emissions Testing Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway in D (A/T) or 5th (M/T). Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
00/08/10 12:39:33 31S5P600_308 Warranty and Customer Relations Customer Relations Information ................................. 306 U.S. Zone Office Map .................... 307 Canada Zone Office Map .............. 308 Warranty Coverages ..................... 309 Reporting Safety Defects (U.S. Vehicles) ........................... 310 Authorized Manuals ......................
00/08/10 12:39:39 31S5P600_309 Customer Relations Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
00/08/10 12:39:57 31S5P600_310 U.S. Zone Office Map Western Zone P.O. Box 2260 700 Van Ness Avenue Torrance, California 90501-1490 (310) 781-4565 Mid-Atlantic Zone 902 Wind River Ln., Suite 200 Gaithersburg, Maryland 20878 (301) 990-2020 1 ZONE 2 ZONE 9 ZONE 8 ZONE 4 ZONE 5 ZONE 10 ZONE 1 ZONE 6 ZONE 15 Northwestern Zone P.O. Box 20186 12439 N.E.
00/08/10 12:40:02 31S5P600_311 Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTÈLE Honda Canada Inc. 715 Milner Avenue Toronto, ON M1B 2K8 Tel: 1-888-9-HONDA-9 Fax: Toll-free 1-877-939-0909 Toronto (416) 287-4776 Honda Canada Inc.
00/08/10 12:40:15 31S5P600_312 Warranty Coverages U.S. Owners Your new Honda is covered by these warranties: New Vehicle Limited Warranty − covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty − these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional.
00/08/10 12:40:20 31S5P600_313 Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
00/08/10 12:40:32 31S5P600_314 Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356.
00/08/10 12:40:40 31S5P600_315 Authorized Manuals NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention the shipment should be sent. For purchases outside U.S.A. please write to the address shown below for a quotation. S H I P T O Customer Name Attention Street Address − No P.O.
00/08/10 12:40:46 31S5P600_316 Index A Accessories and Modifications .... 169 Accessories................................. 169 Additional Safety Precaution.... 170 Modifications ............................. 170 ACCESSORY (Ignition Key Position) ........................................ 82 Accessory Power Socket .............. 103 Additives, Engine Oil..................... 209 Airbag (SRS) .............................. 10, 48 Air Cleaner Element ...................... 225 Air Conditioning System ..........
00/08/10 12:40:51 31S5P600_317 Index C Capacities Chart............................. 294 Carbon Monoxide Hazard .............. 54 Cargo Hook .................................... 104 Carrying Cargo .............................. 171 Cassette Player Care ............................................. 158 Operation .................... 122, 134, 155 CAUTION, Explanation of ............... ii CD Changer ................... 125, 137, 151 CD Player ....................... 125, 137, 149 Ceiling Light .............
00/08/10 12:40:57 31S5P600_318 Index Driving ............................................ 175 Economy ..................................... 168 In Bad Weather .......................... 193 In Foreign Countries ................. 299 E Economy, Fuel ............................... 168 Emergencies on the Road............. 289 Battery, Jump Starting .............. 273 Brake System Indicator ............ 282 Changing a Flat Tire ................. 265 Charging System Indicator ...... 279 Checking the Fuses....
00/08/10 12:41:05 31S5P600_319 Index Fuses, Checking the ...................... 284 G Gas Mileage, Improving................ 168 Gasohol ........................................... 298 Gasoline .......................................... 162 Fuel Reserve Indicator ................ 63 Gauge ............................................ 67 Octane Requirement ................. 162 Tank, Filling the......................... 163 Gas Station Procedures................. 163 Gauges Engine Coolant Temperature ....
00/08/10 12:41:12 31S5P600_320 Index K Lubricant Specifications Chart .... 294 Luggage .......................................... 171 NOTICE, Explanation of .................... i Numbers, Identification ................ 292 Keys ................................................... 79 M O L Label, Certification ........................ 292 Lane Change, Signaling .................. 72 Lap/Shoulder Belts ......................... 44 Lights Bulb Replacement ..................... 247 Indicator ...........
00/08/10 12:41:18 31S5P600_321 Index P Paint Touch-up ............................... 257 Panel Brightness Control ............... 71 Park Gear Position......................... 181 Parking ............................................ 188 Parking Brake ................................ 100 Parking Lights.................................. 70 Parking Over Things that Burn ... 302 PGM-FI System.............................. 301 Polishing and Waxing ................... 257 Pre-Drive Safety Checklist ...........
00/08/10 12:41:24 31S5P600_322 Index Maintenance ................................. 46 Reminder Light and Beeper ....... 61 System Components.................... 44 Use During Pregnancy................ 19 Wearing a Lap/Shoulder Belt .... 16 Seats, Adjusting the ......................... 90 Serial Number ................................ 292 Service Intervals ............................ 198 Service Manual* ............................ 311 Service Station Procedures .......... 163 Setting the Clock ..........
00/08/10 12:41:31 31S5P600_323 Index Time, Setting the ........... 121, 133, 145 Timing Belt ..................................... 237 Tire Chains ..................................... 244 Tire, How to Change a Flat .......... 265 Tires ................................................ 238 Air Pressure ............................... 238 Checking Wear .......................... 240 Compact Spare ........................... 264 DOT Tire Quality Grading ....... 296 Inflation ..................................
00/08/10 12:41:34 31S5P600_324 Index Operating the Power ................... 96 Rear, Defogger ............................ 74 Windshield Cleaning ........................................ 72 Defroster .................................... 113 Washers ........................................ 73 Wipers, Windshield Changing Blades ........................ 232 Operation ...................................... 72 Worn Tires ..................................... 240 Wrecker, Emergency Towing ...... 289 * : U.S.
00/08/10 15:30:13 31S5P600_325 Service Information Summary Fuel Tank Capacity: 13.2 US gal (50 , 11.0 Imp gal) Automatic Transmission Fluid: Honda ATF-Z1 (Automatic Transmission Fluid) preferred, or a DEXRON III ATF as a temporary replacement (see page 220 ). Power Steering Fluid: Honda Power Steering Fluid preferred, or another brand of power steering fluid as a temporary replacement. Do not use ATF (see page 224 ). Recommended Engine Oil: API Premium grade 5W-20 detergent oil (see page 209 ).