, Owner s Manual TILLER F220 AH 英 FM Hi 31V14641 00X31-V14-6410 BK PANTONE 186C Includes US and Canadian Models Printed in Japan C 2018 Honda Motor Co., Ltd.
31V146410-00.fm 0 ページ ２０１８年３月１２日 月曜日 午後８時３６分 The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. California Proposition 65 This product contains or emits chemicals known to the state of California to cause cancer, birth defects or other reproductive harm Keep this owner’s manual handy, so you can refer to it any time.
1V146410.book 1 ページ ２０１８年３月７日 水曜日 午前９時８分 INTRODUCTION Congratulations on your selection of a Honda tiller. We are certain you will be pleased with your purchase of one of the finest tillers on the market. We want to help you get the best results from your new tiller and to operate it safely. This manual contains the information on how to do that; please read it carefully. As you read this manual, you will find information preceded by a symbol.
31V146410.book 2 ページ ２０１８年３月７日 水曜日 午前９時８分 INTRODUCTION A FEW WORDS ABOUT SAFETY Your safety and the safety of others are very important. And using this tiller safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
31V146410.book 3 ページ ２０１８年３月７日 水曜日 午前９時８分 CONTENTS TILLER SAFETY..........................................................................................5 IMPORTANT SAFETY INFORMATION .................................................5 SAFETY LABEL LOCATIONS.................................................................9 CONTROLS ..............................................................................................11 COMPONENT & CONTROL LOCATIONS...........................................
31V146410.book 4 ページ ２０１８年３月７日 水曜日 午前９時８分 CONTENTS SERVICING YOUR TILLER (continued) AIR FILTER INSPECTION .....................................................................36 AIR FILTER CLEANING ........................................................................37 SPARK PLUG SERVICE........................................................................38 CLUTCH CABLE ADJUSTMENT .........................................................40 THROTTLE CABLE ADJUSTMENT ..............................
31V146410.book 5 ページ ２０１８年３月７日 水曜日 午前９時８分 TILLER SAFETY IMPORTANT SAFETY INFORMATION Honda tillers are designed to cultivate earth outdoors. Other uses can result in injury to the operator or damage to the tiller and other property. Most injuries or property damage can be prevented if you follow all the instructions in this manual and on the tiller. The most common hazards are discussed below, along with the best way to protect yourself and others.
31V146410.book 6 ページ ２０１８年３月７日 水曜日 午前９時８分 TILLER SAFETY Fire and Burn Hazards • The exhaust system gets hot enough to ignite some materials. – Keep the tiller at least 3 feet (1 meter) away from buildings and other equipment during operation. – Keep flammable materials away from the tiller. • The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Be careful not to touch the muffler while it is hot. Let the engine cool before storing the tiller indoors.
31V146410.book 7 ページ ２０１８年３月７日 水曜日 午前９時８分 TILLER SAFETY Keep Shields in Place Guards and shields are designed to protect you from being hit by thrown objects and to keep you from touching hot engine parts and moving components. For your safety and the safety of others, keep all shields in place when the engine is running. Wear Protective Clothing Wearing protective clothing will reduce your risk of injury. Do not wear loose clothing, jewelry, short pants, sandals, or go barefoot.
31V146410.book 8 ページ ２０１８年３月７日 水曜日 午前９時８分 TILLER SAFETY Attachments and Modifications Do not make any modifications to your tiller. Modifying your tiller or installing non-Honda attachments can make your tiller unsafe. If you need attachments for your tiller, use only Honda Genuine attachments (see page 59). These products have been designed for your tiller. Non-Honda attachments are usually designed for universal applications.
31V146410.book 9 ページ ２０１８年３月７日 水曜日 午前９時８分 TILLER SAFETY SAFETY LABEL LOCATIONS These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact your Honda servicing dealer for a replacement.
31V146410.book 10 ページ ２０１８年３月７日 水曜日 午前９時８分 TILLER SAFETY Canadian model * * * *: French labels come with the tiller.
31V146410.
31V146410.
31V146410.book 13 ページ ２０１８年３月７日 水曜日 午前９時８分 CONTROLS CONTROLS Fuel Valve FUEL VALVE The fuel valve opens and closes the connection between the fuel tank and the carburetor. The fuel valve must be in the ON position for the engine to run. ON OFF After stopping the engine, turn the fuel valve to the OFF position. Choke Lever CHOKE LEVER The choke lever opens and closes the choke valve in the carburetor. The CLOSED position enriches the fuel mixture for starting a cold engine.
31V146410.book 14 ページ ２０１８年３月７日 水曜日 午前９時８分 CONTROLS Starter Grip STARTER GRIP Pulling the starter grip operates the recoil starter to crank the engine for starting. Throttle Lever The throttle lever controls engine speed. FAST Moving the throttle lever in the directions shown makes the engine run faster or slower. Tine speed is controlled by adjusting the throttle lever. At the maximum throttle position, the tines will rotate at the highest speed.
31V146410.book 15 ページ ２０１８年３月７日 水曜日 午前９時８分 CONTROLS Clutch Lever The clutch lever engages and disengages the transmission that drives the tines. The tiller tines begin to rotate once the engine is started and the clutch lever is squeezed. The tines may momentarily rotate after clutch lever is released. ENGAGED CLUTCH LEVER DISENGAGED Drag Bar The drag bar controls tilling depth and should always be used when tilling. It enables you to compensate for the hardness of the soil.
31V146410.book 16 ページ ２０１８年３月７日 水曜日 午前９時８分 BEFORE OPERATION ARE YOU READY TO GET STARTED? Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Knowledge Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the tiller and its operation before you begin using it. Know how to quickly disengage the controls and shut off the engine in case of an emergency.
31V146410.book 17 ページ ２０１８年３月７日 水曜日 午前９時８分 BEFORE OPERATION Do not place flammable objects close to the engine. Before beginning your pre-operation checks, be sure the tiller is on a level surface and the engine switch is in the OFF position. Check the Engine • Before each use, look around and underneath the engine for signs of oil or gasoline leaks. • Check the oil level (see page 30). • Check the air filter (see page 36).
31V146410.book 18 ページ ２０１８年３月７日 水曜日 午前９時８分 OPERATION SAFE OPERATING PRECAUTIONS Before operating the tiller for the first time, please review both the TILLER SAFETY chapter (see page 5) and the chapter titled BEFORE OPERATION (see page 16). For your safety, do not start or operate the tiller in an enclosed area such as a garage. Your tiller’s exhaust contains poisonous carbon monoxide gas that can collect rapidly in an enclosed area and cause illness or death.
31V146410.book 19 ページ ２０１８年３月７日 水曜日 午前９時８分 OPERATION STARTING THE ENGINE Refer to Safe Operating Precautions on page 18. 1. Check that the drain knob is tightened securely. Turn the fuel valve to the ON position. FUEL VALVE FUEL DRAIN KNOB ON 2. Move the choke lever to the CLOSED position to start a cold engine. Leave the choke lever in the OPEN position to restart a warm engine. CHOKE LEVER OPEN CLOSED 3. Turn the engine switch to the ON position.
31V146410.book 20 ページ ２０１８年３月７日 水曜日 午前９時８分 OPERATION 4. Move the throttle lever away from the SLOW position, about 1/3 of the way toward the FAST position. THROTTLE LEVER SLOW 5. Hold the handle and pull the starter grip until you feel resistance, then pull briskly in the direction of the arrow as shown. Direction to pull Do not allow the starter grip to snap back against the engine. HOLD HERE WHEN STARTING STARTER GRIP 6.
31V146410.book 21 ページ ２０１８年３月７日 水曜日 午前９時８分 OPERATION OPERATING THE CONTROLS FOR TILLING If the tines dig in but the machine will not move forward, move the handlebars from side to side. When turning, push down on the handlebars to bring the tiller’s weight to the rear; this will make turning easier. Handlebar Height Adjustment Stop the engine before adjusting the handlebar height.
31V146410.book 22 ページ ２０１８年３月７日 水曜日 午前９時８分 OPERATION Tilling Depth Adjustment RETAINER The drag bar is used to control the tilling depth, which can be adjusted by removing the pin and retainer and sliding the drag bar up and down as necessary. During operation, if the machine jerks forward while tilling, press down on the handlebars. This will cause the drag bar to dig more deeply into the soil.
31V146410.book 23 ページ ２０１８年３月７日 水曜日 午前９時８分 OPERATION HANDLING TIPS • Adjust the handlebar height to a comfortable position (waist height for normal tilling). • The drag bar should always be used when tilling. It enables you to compensate for the hardness of the soil. The ideal height of the drag bar will depend on the type of soil being tilled and soil conditions at the time of tilling. In general, however, the drag bar should be adjusted so that the tiller is tilted slightly backward.
31V146410.book 24 ページ ２０１８年３月７日 水曜日 午前９時８分 OPERATION STOPPING THE ENGINE To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the following procedure. 1. Release the clutch lever to the DISENGAGED position. Even if you release the clutch, the tine may not stop immediately. ENGAGED CLUTCH LEVER DISENGAGED 2. Move the throttle lever to the slowest position. FAST THROTTLE LEVER SLOW 3. Turn the engine switch to the OFF position.
31V146410.book 25 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER THE IMPORTANCE OF MAINTENANCE Good maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution. To help you properly care for your tiller, the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools.
31V146410.book 26 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Improper maintenance can cause an unsafe condition. Failure to properly follow maintenance instructions and precautions can cause serious injuries or death.
31V146410.book 27 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER MAINTENANCE SCHEDULE REGULAR SERVICE PERIOD (2) Perform at every indicated month or operating hour interval, whichever comes first.
31V146410.book 28 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER REFUELING With the engine stopped and on a level surface, remove the fuel tank cap and check the fuel level. Refill the tank if the fuel level is low. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine and let it cool before handling fuel. • Keep heat, sparks, and flame away. • Handle fuel only outdoors. • Keep away from your vehicle. • Wipe up spills immediately.
V146410.book 29 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER FUEL TANK CAP UPPER LIMIT LINE FUEL TANK GASOLINE After refueling, tighten the fuel tank cap securely. FUEL RECOMMENDATIONS This engine is certified to operate on unleaded gasoline with a pump octane rating of 86 or higher. Never use gasoline that is stale, contaminated, or mixed with oil. Avoid getting dirt or water in the fuel tank.
31V146410.book 30 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER ENGINE OIL LEVEL CHECK Check the engine oil level with the engine stopped and in a level position. Make sure the area around the oil filler cap is clean. 1. Remove the oil filler cap. 2. Check the oil level. If it is below the upper limit, fill with the recommended oil (see page 32) to the upper limit. 3. Reinstall the oil filler cap securely.
31V146410.book 31 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER ENGINE OIL CHANGE Drain the oil while the engine is warm to assure rapid and complete draining. Make sure the area around the drain plug and the oil filler cap are clean. 1. Place a suitable container below the engine to catch the used oil, and then remove the oil filler cap, drain plug, and sealing washer. 2. Allow the used oil to drain completely, and then reinstall the drain plug with a new sealing washer. Tighten the plug securely.
31V146410.book 32 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER ENGINE OIL RECOMMENDATIONS Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for general use. Other viscosities shown in the chart may be used when the average temperature in your area is within the recommended range. AMBIENT TEMPERATURE The SAE oil viscosity and service category are in the API label on the oil container.
31V146410.book 33 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER TRANSMISSION OIL LEVEL CHECK (USA model) Check the transmission oil level with the tiller on a level surface and the engine stopped. Make sure the area around the oil level check bolt is clean. 1. Remove the transmission oil level check bolt and sealing washer. Check the oil level. The oil should be level with the lower edge of the oil filler hole. If the transmission oil level is low, add the recommended oil by the following procedure.
31V146410.book 34 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER 3. Remove the recoil cover cap nuts and remove the recoil cover. 4. Remove the fuel tank cap, neck seal, and fan cover. Carefully remove the choke rod from the choke valve hole as shown. CAP NUT (3) RECOIL COVER CHOKE ROD FUEL TANK CAP NECK SEAL FAN COVER CHOKE VALVE HOLE 5. Reinstall the fuel tank cap to prevent foreign objects from entering the fuel tank. 6. Make sure the area around the oil filler cap is clean.
31V146410.book 35 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER Assembly 8. Remove the fuel tank cap. Verify the choke lever is in the CLOSED position and reinstall the fan cover by inserting the choke rod into the choke valve hole. • The choke lever will not operate if the choke rod is not inserted correctly into the choke valve hole as shown below. 9. Reinstall the neck seal and fuel tank cap as shown. NECK SEAL 10.Reinstall the recoil cover, and tighten the recoil cover cap nuts securely.
31V146410.book 36 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER AIR FILTER INSPECTION Press the latch tabs on the fuel tank side of the air cleaner cover, remove the air cleaner cover, and remove the filter. Check the filter to be sure it is clean and in good condition. If the filter is dirty, remove the filter and clean it as described on page 37. Replace the filter if it is heavily clogged or damaged. Reinstall the filter and air cleaner cover. Make sure the latch tabs are secured.
31V146410.book 37 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER AIR FILTER CLEANING A dirty air filter will restrict air flow to the carburetor, reducing engine performance. If you operate the tiller in very dusty areas, clean the air filter more frequently than specified in the Maintenance Schedule. 1. Tap the air filter element several times on a hard surface to remove dirt, or blow compressed air [not exceeding 207 kPa (2.1 kgf/cm2, 30 psi)] through the air filter from the air cleaner housing side.
31V146410.book 38 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER SPARK PLUG SERVICE Recommended spark plug: U14FSR-UB (DENSO) An incorrect spark plugs can cause engine damage. For good performance, the spark plug must be properly gapped and free of deposits. Allow the engine to cool before servicing the spark plug. 1. Disconnect the spark plug cap, and remove any dirt from around the spark plug area. 2. Remove the spark plug with a spark plug wrench.
31V146410.book 39 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER 3. Inspect the spark plug. Replace it if the electrodes are worn or the insulator is cracked, chipped, or fouled. 4. Measure the spark plug electrode gap with a wire-type feeler gauge. Correct the gap, if necessary, by carefully bending the side electrode. 0.024 – 0.028 in (0.6 – 0.7 mm) SEALING WASHER The gap should be: 0.024 – 0.028 in (0.6 – 0.7 mm) 5. Install the spark plug carefully, by hand, to avoid cross-threading. 6.
31V146410.book 40 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER CLUTCH CABLE ADJUSTMENT 1. Set the handlebar height in the center position (see page 21). 2. Measure the spring lengths when the clutch lever is operated to the DISENGAGED and ENGAGED positions. 3. With the clutch lever ENGAGED, adjust so that the extension value of the clutch spring is as measured below. Extension value: A (ENGAGED) - a (DISENGAGED) = 0.08 ± 0.02 in (2 ± 0.
31V146410.book 41 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER THROTTLE CABLE ADJUSTMENT Measure the free play at the lever tip. Free play: 0.39 – 0.59 in (10.0 – 15.0 mm) If the free play is incorrect, loosen the lock nut and turn the adjusting nut in or out as required. After adjustment, tighten the lock nut. LOCK NUT 0.39 – 0.59 in (10.0 – 15.
31V146410.book 42 ページ ２０１８年３月７日 水曜日 午前９時８分 SERVICING YOUR TILLER SPARK ARRESTER SERVICE (optional part) Your engine is not factory-equipped with a spark arrester. In some areas, it is illegal to operate an engine without a spark arrester. Check local laws and regulations. A spark arrester is available from Honda servicing dealers. The spark arrester must be serviced every 100 hours to keep it functioning as designed. If the engine has been running, the muffler will be very hot.
31V146410.book 43 ページ ２０１８年３月７日 水曜日 午前９時８分 STORAGE STORAGE PREPARATION Proper storage preparation is essential for keeping your tiller trouble free and looking good. The following steps will help to keep rust and corrosion from impairing your tiller’s function and appearance, and will make the engine easier to start when you use the tiller again. Cleaning 1. Wash the tiller, including the underside. Engine Wash the engine by hand, and be careful to prevent water from entering the air cleaner.
31V146410.book 44 ページ ２０１８年３月７日 水曜日 午前９時８分 STORAGE 2. After washing the tiller, wipe dry all accessible surfaces. 3. Start the engine outdoors, and let it run until it reaches normal operating temperature to evaporate any water remaining on the engine. 4. While the engine is running, operate the clutch lever to expel water from the pulleys, belts, and other moving items. 5. Stop the engine and allow it to cool. 6.
31V146410.book 45 ページ ２０１８年３月７日 水曜日 午前９時８分 STORAGE The Distributor's Limited Warranty (U.S.) / Distributor's Warranty (CA.) does not cover fuel system damage or engine performance problems resulting from neglected storage preparation. You can extend fuel storage life by adding a gasoline stabilizer that is formulated for that purpose, or you can avoid fuel deterioration problems by draining the fuel tank and carburetor.
31V146410.book 46 ページ ２０１８年３月７日 水曜日 午前９時８分 STORAGE Draining the Fuel Tank and Carburetor 1. Place an approved gasoline container below the carburetor, and use a funnel to avoid spilling fuel. 2. Loosen the carburetor drain knob, and then move the fuel valve to the ON position. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine and let it cool before handling fuel. • Keep heat, sparks, and flame away. • Handle fuel only outdoors.
31V146410.book 47 ページ ２０１８年３月７日 水曜日 午前９時８分 STORAGE Engine Oil Change the engine oil (see page 31). Engine Cylinder 1. Remove the spark plug (see page 38). 2. Pour a teaspoon (5 cc) of clean engine oil into the cylinder. 3. Gently pull the starter grip several times to distribute the oil in the cylinder. 4. Reinstall the spark plug and spark plug cap. 5. Pull the starter grip slowly until you feel resistance, and then return the starter grip gently.
31V146410.book 48 ページ ２０１８年３月７日 水曜日 午前９時８分 STORAGE STORAGE PRECAUTIONS Follow Honda's recommendations for safe storage of your tiller. If your tiller will be stored with gasoline in the fuel tank and carburetor, it is important to reduce the hazard of gasoline vapor ignition. Select a well ventilated storage area away from any appliance that operates with a flame, such as a furnace, water heater, or clothes dryer.
31V146410.book 49 ページ ２０１８年３月７日 水曜日 午前９時８分 TRANSPORTING Follow Honda's recommendations for safe loading, unloading, and transporting your tiller. BEFORE LOADING If the engine has been running, allow it to cool for at least 15 minutes before loading the tiller on the transport vehicle. A hot engine and exhaust system can burn you and can ignite some materials. To prevent fuel spillage, drain fuel from the fuel tank (see page 46). Always turn the engine switch to the OFF position.
31V146410.book 50 ページ ２０１８年３月７日 水曜日 午前９時８分 TAKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT START Possible Cause Fuel valve OFF. Choke OPEN. Correction Turn valve ON. Move to CLOSE unless engine is warm. Turn engine switch to ON. Refuel (p. 28). Drain fuel tank and carburetor (p. 46). Refuel with fresh gasoline (p. 28). Gap or replace spark plug (p. 38). Engine switch OFF. Out of fuel. Bad fuel, tiller stored without treating or draining gasoline, or refueled with bad gasoline.
31V146410.book 51 ページ ２０１８年３月７日 水曜日 午前９時８分 TAKING CARE OF UNEXPECTED PROBLEMS ENGINE LACKS POWER Possible Cause Air filter clogged. Bad fuel, tiller stored without treating or draining gasoline, or refueled with bad gasoline. Fuel filter clogged, carburetor malfunction, ignition malfunction, valves struck, etc. Correction Clean or replace air filter (P. 37). Drain fuel tank and carburetor (p. 46). Refuel with fresh gasoline (p. 28). Replace or repair faulty components as necessary.
31V146410.book 52 ページ ２０１８年３月７日 水曜日 午前９時８分 TECHNICAL INFORMATION Serial Number Locations FRAME SERIAL NUMBER ENGINE SERIAL NUMBER Record the engine and frame serial numbers in the spaces below. You will need these serial numbers when ordering parts, and when making technical or warranty inquiries (see page 60).
31V146410.book 53 ページ ２０１８年３月７日 水曜日 午前９時８分 TECHNICAL INFORMATION Carburetor Modification for High Altitude Operation At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting. Operation at an altitude that differs from that at which this engine was certified, for extended periods of time, may increase emissions.
31V146410.book 54 ページ ２０１８年３月７日 水曜日 午前９時８分 TECHNICAL INFORMATION Emission Control System Information Source of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon monoxide does not react in the same way, but it is toxic.
31V146410.book 55 ページ ２０１８年３月７日 水曜日 午前９時８分 TECHNICAL INFORMATION Problems That May Affect Emissions If you are aware of any of the following symptoms, have your engine inspected and repaired by your authorized Honda servicing dealer. • • • • • Hard starting or stalling after starting. Rough idle. Misfiring or backfiring under load. Afterburning (backfiring). Black exhaust smoke or high fuel consumption.
31V146410.book 56 ページ ２０１８年３月７日 水曜日 午前９時８分 TECHNICAL INFORMATION Air Index (Models certified for sale in California) An Air Index Information label is applied to engines certified to an emission durability time period in accordance with the requirements of the California Air Resources Board. The bar graph is intended to provide you, our customer, the ability to compare the emissions performance of available engines. The lower the Air Index, the less pollution.
31V146410.book 57 ページ ２０１８年３月７日 水曜日 午前９時８分 TECHNICAL INFORMATION Emission Control System Warranty Your new Honda complies with both the U.S. EPA and State of California emission regulations. American Honda provides the same emission warranty coverage for Honda Power Equipment engines sold in all 50 states. In all areas of the United States, your Honda Power Equipment engine is designed, built, and equipped to meet the U.S.
31V146410.book 58 ページ ２０１８年３月７日 水曜日 午前９時８分 TECHNICAL INFORMATION Specifications Model Type Description code Dry mass [weight] Length Width Height Engine model F220K1 AT2 type Engine type Displacement Bore x Stroke Ignition system Spark plug Oil capacity Fuel tank capacity Clutch Transmission oil capacity CT2 type FAAJ 52.9 lbs (24 kg) 57.3 lbs (26 kg) 47.2 in (1,200 mm) 21.5 in (545 mm) 23.0 in (585 mm) 38.
31V146410.book 59 ページ ２０１８年３月７日 水曜日 午前９時８分 CONSUMER INFORMATION Dealer Locator Information To find an authorized Honda Servicing Dealer For USA: Visit our website: http://powerequipment.honda.com/dealer-locator For Canada: Call 1-888-946-6329 or visit our website: English http://powerequipment.honda.ca/dealerlocator French http://powerequipment.honda.ca/trouver-concessionaire Honda Publications Shop Manual This manual covers complete maintenance and overhaul procedures.
31V146410.book 60 ページ ２０１８年３月７日 水曜日 午前９時８分 CONSUMER INFORMATION Customer Service Information Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership’s management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
31V146410.book 61 ページ ２０１８年３月７日 水曜日 午前９時８分 QUICK REFERENCE INFORMATION Fuel Type Engine Oil Type Spark Plug Type Before each use, check the following. Maintenance First 20 hours Subsequent Regular unleaded gasoline with an ethanol content of no more than 10% and a pump octane rating of 86 or higher (see page 29) SAE 10 W – 30, API SJ or later, for general use (see page 32) Maximum oil capacity: 10 US oz (0.30 L, 10.
, Owner s Manual TILLER F220 AH 英 FM Hi 31V14641 00X31-V14-6410 BK PANTONE 186C Includes US and Canadian Models Printed in Japan C 2018 Honda Motor Co., Ltd.
