Owner's Manual

ManualsBrandsHonda ManualsTillerHonda FG110 FAAA-1200001 through 1235476

INTRODUCTION

Congratulations on your selection of a Honda FG110 mini-tiller!

We are certain you will be pleased with your purchase of one of the

finest tillers on the market.

We want to help you get the best results from your new tiller and to

operate it safely. This manual contains the information on how to do

that; please read it carefully.

We suggest you read the DISTRIBUTOR’S LIMITED WARRANTY

(page 21) and EMISSION CONTROL SYSTEM WARRANTY

(page 22) to fully understand coverage and your responsibilities of

ownership.

When your tiller needs scheduled maintenance, keep in mind that an

authorized Honda servicing dealer is specially trained in servicing

Honda tillers and is supported by the parts and service divisions of

American Honda. Your Honda dealer is dedicated to your satisfaction

and will be pleased to answer your questions and concerns.

Keep this owner’s manual handy, so you can refer to it at any time.

This owner’s manual is considered a permanent part of the tiller and

should remain with the tiller if resold.

The information and specifications included in this publication were in

effect at the time of approval for printing. American Honda Motor Co.,

Inc. reserves the right, however, to discontinue or change

specifications or design at any time without notice and without

incurring any obligation whatever. No part of this publication may be

reproduced without written permission.

SAFETY MESSAGES

Your safety and the safety of others are very important. We have

provided important safety messages in this manual and on the tiller.

This information alerts you to potential hazards that could hurt you or

others. Please read these messages carefully.

Of course, it is not practical or possible to warn you about all the

hazards associated with operating or maintaining a mini-tiller. You

must use your own good judgment.

You will find important safety information in a variety of forms:

• Safety Labels – on the tiller.

• Instructions – how to use this tiller correctly and safely.

• Safety Messages – preceded by a safety alert A symbol and one

of three signal words: DANGER, WARNING, or CAUTION. These

signal words mean:

Each message tells you what the hazard is, what can happen, and

what you can do to avoid or reduce injury.

• Damage Prevention Messages – You will also see other

important messages that are preceded by the word NOTICE. This

word means:

CONTENTS

B DANGER

You WILL be KILLED or SERIOUSLY

HURT if you don't follow instructions.

B WARNING

You CAN be KILLED or SERIOUSLY

HURT if you don't follow instructions.

B CAUTION

You CAN be HURT if you don't follow

instructions.

NOTICE

Your tiller or other property can be damaged if

you don’t follow instructions.

INTRODUCTION ...............................1

SAFETY MESSAGES........................1

TILLER SAFETY................................2

IMPORTANT SAFETY

INFORMATION.............................2

ATTACHMENTS AND

MODIFICATIONS .........................2

SAFETY LABEL LOCATION ........3

SETTING UP YOUR NEW TILLER ...3

CONTROL LOCATIONS ...................4

BEFORE OPERATION......................4

ARE YOU READY TO OPERATE

THE TILLER? ...............................4

IS YOUR WORKING AREA

READY? .......................................4

IS YOUR TILLER READY TO GO? ..4

OPERATION......................................5

SAFE OPERATING PRECAUTIONS........5

STARTING THE ENGINE.............6

STOPPING THE ENGINE ............7

TILLER OPERATION ...................7

SERVICING YOUR TILLER ..............8

MAINTENANCE SAFETY.............8

MAINTENANCE SCHEDULE .......8

ENGINE OIL .................................9

AIR FILTER ................................10

SPARK PLUG.............................11

SPARK ARRESTER (OPTIONAL

EQUIPMENT) .............................11

REFUELING ............................... 12

TRANSMISSION LUBRICATION............14

TRANSPORTING ............................ 15

STORAGE ....................................... 15

TAKING CARE OF UNEXPECTED

PROBLEMS..................................... 17

TECHNICAL INFORMATION .......... 17

SERIAL NUMBER LOCATIONS. 17

CARBURETOR

MODIFICATION FOR HIGH

ALTITUDE OPERATION ............ 17

EMISSION CONTROL SYSTEM 18

AIR INDEX.................................. 18

SPECIFICATIONS...................... 19

CONSUMER INFORMATION ......... 20

REPLACEMENT PARTS,

OPTIONAL EQUIPMENT, AND

SERVICE ITEMS........................ 20

DEALER LOCATOR

INFORMATION........................... 20

CUSTOMER SERVICE

INFORMATION........................... 20

DISTRIBUTOR'S LIMITED

WARRANTY ............................... 21

ACCESSORIES,

REPLACEMENT PARTS, AND

APPAREL WARRANTY.............. 21

EMISSION CONTROL SYSTEM

WARRANTY ............................... 22

OWNER’S MANUAL

FG110

B WARNING: B

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

31V25033

00X31-V25-0330

POM31V25033

IPC.XXX.2008.11

PRINTED IN U.S.A.

EM5

Summary of content (24 pages)

PAGE 1
INTRODUCTION Congratulations on your selection of a Honda FG110 mini-tiller! We are certain you will be pleased with your purchase of one of the finest tillers on the market. OWNER’S MANUAL FG110 We want to help you get the best results from your new tiller and to operate it safely. This manual contains the information on how to do that; please read it carefully.
PAGE 2
TILLER SAFETY This chapter explains what you need to know to operate your tiller safely. IMPORTANT SAFETY INFORMATION Honda Tiller Usage Honda tillers are designed to give safe and dependable service if operated according to instructions and intended use. IMPORTANT MESSAGE TO EMPLOYERS As an employer, you have special responsibilities to the people who work for you.
PAGE 3
SAFETY LABEL LOCATION Engine Oil The label shown here contains important safety information. Please read it carefully. This label is considered a permanent part of your tiller. If the label comes off or becomes hard to read, contact your authorized Honda tiller dealer for a replacement. The tiller is shipped WITHOUT OIL in the engine. All Honda engines are run at the factory prior to packaging. Most of the oil is removed prior to shipment; however, some oil remains in the engine.
PAGE 4
CONTROL LOCATIONS CHOKE LEVER (P. 6) BEFORE OPERATION ARE YOU READY TO OPERATE THE TILLER? STARTER GRIP PRIMING BULB (P. 6) Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the tiller and its operation before you begin using it. Know how to quickly shut off the engine in case of an emergency. FUEL CAP (P.
PAGE 5
Safety Inspection Tine Installation • Look around the engine for signs of oil or gasoline leaks. Wipe up any spills before starting the engine. Make sure the tines are installed properly with the blades angled inward and the tine spacers facing each other. The leading edge of each blade is slanted. • Replace any damaged parts. TINE SPACERS • Check that all fasteners are in place and secure. Tighten as necessary.
PAGE 6
Moving the Tiller STARTING THE ENGINE The tiller has wheels to allow easy maneuvering to and from the work area. 1. Move the engine switch to the ON position. Do not transport the tiller with the engine running. ENG. SW. OFF ON OFF 2. To start a cold engine, move the choke lever up to the CLOSED (E) position. To restart a warm engine, leave the choke lever down in the OPEN position.
PAGE 7
STOPPING THE ENGINE Tilling With the Drag Bar Installed 1. Release the throttle lever. 1. Install the drag bar and set the tilling depth by moving the drag bar up or down into one of 4 height positions (page 5). ENG. SW. 2. Move the engine switch to the OFF position. OFF ON OFF The ideal height of the drag bar will depend on the type of soil being tilled and soil conditions at the time of tilling. In general, however, the drag bar should be adjusted so that the tiller is tilted slightly backward. 2.
PAGE 8
SERVICING YOUR TILLER Proper maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution. B WARNING Improper maintenance, or failure to correct a problem before operation, can cause a malfunction in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.
PAGE 9
ENGINE OIL capacity is small. Be sure the engine is in a level position, as shown. Oil Recommendations OIL LEVEL Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for general use. Other viscosities shown in the chart may be used when the average temperature in your area is within the recommended range. The SAE oil viscosity and service category are in the API label on the oil container.
PAGE 10
AIR FILTER Cleaning Inspection 1. Move the choke lever to the CLOSED (E) position to prevent dirt from entering the engine. AIR CLEANER BASE CHOKE LEVER 1. Remove the air filter. 2. Clean the air filter in warm soapy water, rinse, and allow it to dry thoroughly. Or, clean in nonflammable solvent and allow it to dry. 2. Squeeze together the air cleaner upper tabs at the top of the air cleaner cover to release it from its catch, then flip the cover down to remove it. 3.
PAGE 11
SPARK PLUG SPARK ARRESTER (OPTIONAL EQUIPMENT) Recommended Spark Plug: NGK - CMR5H Your tiller engine is not factory-equipped with a spark arrester. In some areas, it is illegal to operate an engine without a spark arrester. Check local laws and regulations. An optional USDA approved spark arrester is available from an authorized Honda servicing dealer. See page 20 for part numbers. NOTICE An incorrect spark plug can cause engine damage. 1.
PAGE 12
Throttle Cable Inspection REFUELING Verify the throttle trigger operates smoothly, releases properly, and the throttle cable is undamaged. If there is visible damage, or if the throttle lever does not operate smoothly or release properly, take your tiller to your authorized Honda servicing dealer. Honda recommends using a No-Spill® gas can, which meets the demanding requirements of the California Air Resources Board (page 20).
PAGE 13
Fuel Tube Inspection Fuel Filter and Fuel Tank Cleaning Check the fuel supply and return tubes, and replace any tube that is damaged, cracked, or leaking. 1. Remove the fuel tank cap. Refer to the Honda shop manual for tube replacement instructions, or take the tiller to an authorized Honda servicing dealer. FUEL RETURN TUBE (clear) 2. Tip the tiller as shown and empty the fuel tank into an approved gasoline container. Use a funnel to avoid spilling gasoline. FUEL SUPPLY TUBE (black) 3.
PAGE 14
TRANSMISSION LUBRICATION [a] The transmission is pre-lubricated at the factory. At the beginning of each tilling season, or after every 25 hours of use during the season, the transmission should be filled with grease. Replacement grease should be a high quality petroleum based NLGI #2 general purpose grease usually available in disposable tubes at most hardware or automotive parts stores. [b] [c] [d] RIGHT OUTER TINE 1. Place the tiller on the left side as shown. 2.
PAGE 15
TRANSPORTING STORAGE BEFORE LOADING STORAGE PREPARATION If the engine has been running, allow it to cool for at least 15 minutes before loading the tiller on the transport vehicle. A hot engine and exhaust system can burn you and can ignite some materials. Proper storage preparation is essential for keeping your tiller trouble-free and looking good.
PAGE 16
Adding Fuel Stabilizer To Extend Fuel Storage Life STORAGE PRECAUTIONS When adding a fuel stabilizer, fill the fuel tank with fresh gasoline. If only partially filled, air in the tank will promote fuel deterioration during storage. If you keep a container of gasoline for refueling, be sure that it contains only fresh gasoline. If your tiller will be stored with gasoline in the fuel tank and carburetor, it is important to reduce the hazard of gasoline vapor ignition.
PAGE 17
TAKING CARE OF UNEXPECTED PROBLEMS TECHNICAL INFORMATION SERIAL NUMBER LOCATIONS Engine Will Not Start Possible Cause Correction Engine switch OFF. Turn the engine switch ON (page 6). Choke lever not in CLOSED (E) position (cold engine). Move the lever to the CLOSED (E) position (page 6). Out of fuel. Add fuel and press the priming bulb to fill the carburetor (page 6). Bad fuel, tiller stored without treating or draining gasoline, refueled with bad gasoline. Drain the fuel tank.
PAGE 18
EMISSION CONTROL SYSTEM AIR INDEX Source of Emissions An Air Index Information hang tag/label is applied to engines certified to an emission durability time period in accordance with the requirements of the California Air Resources Board. The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight.
PAGE 19
Maintenance SPECIFICATIONS ENGINE Fuel Model GX25 Type 4-stroke, overhead cam, single cylinder GCALT Description code Displacement 1.5 cu in (25 cc) Bore & stroke 1.4 x 1.0 in (35 x 26 mm) Compression ratio 8.0:1 Cooling system Forced-air Ignition system Transistorized magneto Ignition timing 30° B.T.D.C.
PAGE 20
CONSUMER INFORMATION REPLACEMENT PARTS, OPTIONAL EQUIPMENT, AND SERVICE ITEMS Contact an authorized Honda servicing dealer to purchase any of these (or other) Honda Genuine items for your tiller.
PAGE 21
DISTRIBUTOR'S LIMITED WARRANTY This warranty is limited to the following Honda Power Equipment products when distributed by: American Honda Motor Co., Inc., Power Equipment Division, 4900 Marconi Drive, Alpharetta, Georgia 30005-8847.
PAGE 22
EMISSION CONTROL SYSTEM WARRANTY Your new Honda Power Equipment engine complies with the U.S. EPA, Environment Canada, and State of California emission regulations (models certified for sale in California only). American Honda Motor Co., Inc. provides the emission warranty coverage for engines in the United States and its territories. Honda Canada Inc. provides the emission warranty for engines in the 13 provinces and territories of Canada.
PAGE 23
NOTES
PAGE 24
Printed on Recycled Paper