Installation Instructions

ManualsBrandsHonda ManualsMotorGoldwing F6B Backrest

Issue Date

December 2012

INSTALLATION

INSTRUCTIONS

Accessory Application Publication No.

MII 14360

PARTS LIST

87940-MJG-6701

1 of 5

BACKREST WITH PAD

P/N 08R71-MJG-670

GL1800B

No. Description Qty

(1) Installation Instruction URL 1

(2) Backrest 1

(3) Backrest bracket 1

(4) Center backrest stay 1

(5) Backrest cover 1

(6) 8 mm socket bolt (long) 4

(7) 5 mm screw 2

(8) Clip 2

(9) Hex plug 4

(10) 8 mm socket bolt (short) 2

(11) 6 mm flange bolt 4

(12) Rubber 2

TOOLS REQUIRED

Socket (10 mm)

Ratchet

Hex wrench (5 and 6 mm)

Torque wrench

TORQUE CHART

Tighten all screws, bolts, and nuts to their specified

torque values. Refer to the Service Manual for the torque

values of the removed parts.

Item N·m kgf·m Ibf·ft

5 mm screw 4.2 0.4 3.1

6 mm flange bolt 12 1.2 9

8 mm socket bolt 22 2.2 16

8 mm SH flange bolt 27 2.8 20

(11)

(3)

(8)

(2)

(5)

(7)

(12)

(9)

(6)

(4)

(1)

(10)

8 mm SOCKET

BOLT (short)

8 mm SOCKET BOLT

(medium) (Save)

CARRIER

PLATE

COLLAR

(long)

COLLAR (short)

HEX PLUG (Save)

INSTALLATION

NOTE:

This Carrier & Backrest Attachment is required for •

installation of this accessory.

Steps 2 through 9 are not required if the motorcycle •

is already equipped with the Rear Carrier.

1. Remove the carrier plate as shown.

This step is applicable only if the motorcycle •

is already equipped with the Rear Carrier.

No. Description Qty

(1) Right backrest stay 1

(2) Left backrest stay 1

(3) Right rear top lid 1

(4) Left rear top lid 1

(5) 8 mm SH flange bolt 4

Not required if the motorcycle is already

equipped with the rear carrier.

(3)

(1)

(5)

(4)

(2)

CARRIER & BACKREST ATTACHMENT (Sold separately)

Summary of content (5 pages)

PAGE 1
Accessory Application Publication No. MII 14360 INSTALLATION INSTRUCTIONS BACKREST WITH PAD GL1800B P/N 08R71-MJG-670 Issue Date December 2012 PARTS LIST TOOLS REQUIRED Socket (10 mm) Ratchet Hex wrench (5 and 6 mm) Torque wrench (1) (2) (10) (8) (5) (11) TORQUE CHART Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts. (4) (9) (3) (6) Item (7) (12) No.
PAGE 2
. Remove the motorcycle’s parts as shown. BOLT 4. Remove the motorcycle’s parts as shown. RIGHT PASSENGER GRIP CENTER REAR TOP COVER WASHER LEFT PASSENGER GRIP FLANGE COLLAR BOLT BOLT BOLT WASHER WASHER FLANGE COLLAR END REAR TOP COVER FLANGE COLLAR SEAT 5. Remove the rear top lids as shown. • Take care not to break the retaining tabs of the rear top lid. RIGHT REAR TOP LID (Save) LEFT REAR TOP LID (Save) CENTER REAR TOP COVER 3. Remove the antenna as shown.
PAGE 3
6. 8. Install the accessory rear top lids as shown. ACCESSORY LEFT REAR TOP LID Install the backrest stays as shown. ACCESSORY RIGHT REAR TOP LID 8 mm SH FLANGE BOLT CENTER REAR TOP COVER LEFT BACKREST STAY RIGHT BACKREST STAY ANTENNA BASE (Reuse) Install the screws as shown. SCREW (Reuse) 9. Install the motorcycle’s parts in the reverse order of removal. 10. Install the center backrest stay as shown. CENTER BACKREST STAY REAR TOP LID 7. Remove the bolt as shown.
PAGE 4
14. Install the backrest cover as shown. 11. Install the rubbers on the backrest bracket as shown. RUBBER BACKREST BACKREST BRACKET BACKREST COVER 12. Install the assembled backrest on the backrest bracket as shown. 15. Secure the backrest cover as shown. ASSEMBLED BACKREST 8 mm SOCKET BOLT (short) BACKREST BACKREST COVER BACKREST BRACKET 13. Install the clips to the backrest cover as shown.
PAGE 5
16. Install the assembled backrest as shown. ASSEMBLED BACKREST HEX PLUG of the accessory 8 mm SOCKET BOLT (long) When installing the Rear carrier (Sold separately) HEX PLUG of the accessory 8 mm SOCKET BOLT (long) Included in the rear carrier. 8 mm SOCKET BOLT (short) Included in the rear carrier. CARRIER PLATE BACKREST COLLAR (short) Included in the rear carrier. COLLAR (long) Included in the rear carrier.