Front Cover.
Inside front cover.ai 1 3/22/2016 12:32:57 PM ! WARNING: ! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. C M Y CM California Proposition 65 This product contains or emits chemicals known to the state of California to cause cancer, birth defects or other reproductive harm MY CY CMY K Keep this owner’s manual handy, so you can refer to it any time.
INTRODUCTION Congratulations on your selection of a Honda snow blower! We are certain you will be pleased with your purchase of one of the finest snow blowers on the market. We want to help you get the best results from your new snow blower and to operate it safely. This manual contains the information on how to do that; please read it carefully. As you read this manual, you will find information preceded by a symbol.
INTRODUCTION A FEW WORDS ABOUT SAFETY Your safety and the safety of others are very important. And using this snowblower safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining a snow blower.
CONTENTS SNOW BLOWER SAFETY...........................................................5 IMPORTANT SAFETY INFORMATION.......................................5 SAFETY LABEL LOCATIONS ...................................................8 INITIAL USE INSTRUCTIONS .....................................................9 LIST OF LOOSE PARTS ..........................................................9 ADD ENGINE OIL.................................................................10 REGISTER YOUR SNOW BLOWER ...........
CONTENTS REFUELING.........................................................................44 FUEL RECOMMENDATIONS..................................................45 ENGINE OIL LEVEL CHECK ...................................................46 ENGINE OIL CHANGE...........................................................47 ENGINE OIL RECOMMENDATIONS ........................................48 SPARK PLUG SERVICE.........................................................49 TRACK ADJUSTMENT ........................
SNOW BLOWER SAFETY IMPORTANT SAFETY INFORMATION Honda snow blowers are designed to clear snow from driveways and walkways. Other uses can result in injury to the operator or damage to the snow blower and other property. Most injuries or property damage with snow blowers can be prevented if you follow all instructions in this manual and on the snow blower. The most common hazards are discussed below, along with the best way to protect yourself and others.
SNOW BLOWER SAFETY Keep Shields in Place Guards and shields are designed to protect you from being hit by thrown objects and to keep you from touching hot engine parts and moving components. For your safety and the safety of others, keep all shields in place when the engine is running. Adjust the snow discharge chute to avoid hitting the operator, bystanders, windows, and other objects with ejected snow. Stay clear of the snow discharge chute while the engine is running.
SNOW BLOWER SAFETY Operating Conditions Do not use the snow blower when visibility is poor. Under conditions of poor visibility, there is a greater risk of striking an obstacle or causing injury. Adjust the snow discharge chute to avoid hitting bystanders or vehicles. Stay clear of the snow discharge chute while the engine is running and be aware that loose clothing can get drawn into the moving parts.
SNOW BLOWER SAFETY SAFETY LABEL LOCATIONS These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact your Honda snow blower dealer for a replacement.
INITIAL USE INSTRUCTIONS LIST OF LOOSE PARTS Remove the loose parts carton and compare the loose parts against the following list. Contact an authorized Honda dealer from whom you purchased the snow blower if any of the loose parts shown are not included with your snow blower. Ref No. Description Qty.
INITIAL USE INSTRUCTIONS ADD ENGINE OIL The snow blower is shipped WITHOUT OIL in the engine. OIL FILLER CAP UPPER LIMIT 1.With the snow blower on a level surface, remove the oil filler cap/ dipstick. 2.Add oil from the included bottle(s) of oil into the oil filler opening until it reaches the upper limit mark on the dipstick. Do not thread the dipstick in when checking the oil level. All Honda engines are run at the factory prior to packaging.
INITIAL USE INSTRUCTIONS PLEASE REGISTER YOUR SNOW BLOWER Please take a few minutes and register your purchase with Honda. You can register by: • Completing and mailing the registration card included with your snow blower • Going online to powerequipment.honda.
CONTROLS & FEATURES COMPONENT & CONTROL LOCATIONS Use the illustrations on these pages to locate and identify the most frequently used controls.
CONTROLS & FEATURES JOYSTICK CHUTE CONTROL FUEL TANK CAP THROTTLE LEVER SHIFT LEVER DRIVE CLUTCH LEVER CHUTE GUIDE SNOW DISCHARGE CHUTE MUFFLER WHEEL AUGER AUGER CLUTCH LEVER LED WORK LIGHT SNOW CLEARING BAR ENGINE OIL FILLER CAP STEERING CONTROL LEVER (2) ENGINE SERIAL NUMBER CHOKE KNOB ENGINE SWITCH FUEL VALVE STARTER GRIP SKID SHOE (2) FRAME SERIAL NUMBER 13
CONTROLS & FEATURES CONTROLS Engine Switch OFF ON The engine switch controls the ignition system. The key can only be inserted and removed when turned to OFF. (Recoil Starter AT, AW) OFF – Stops the engine. ON – Running position, and for starting with the recoil starter. (DC Electric Starter ATD, AWD) RECOIL ENGINE SWITCH OFF ON OFF – Stops the engine. START ON – Running position, and for starting with the recoil starter. START - Use this position to start the engine with the DC electric starter.
CONTROLS & FEATURES Hour Meter (HSS1332A ATD) OFF – The accumulated engine running time indicator is OFF. HOUR METER ON – The hour meter comes on, then the accumulated engine running time is shown. START – After starting, the dot of the hour meter blinks and the engine running time is accumulated. Fuel Valve Lever The fuel valve opens and closes the fuel line leading from the fuel tank to the carburetor. Make sure that the fuel valve lever is positioned exactly at either the ON or OFF position.
CONTROLS & FEATURES Throttle Lever The throttle lever controls engine speed from SLOW to FAST, and it will stay in any designated position. NOTE: For best snow blowing performance, keep the throttle lever in the FAST position. FAST FAST FAST SLOW SLOW SLOW THROTTLE LEVER Choke Knob The choke knob opens and closes the choke valve in the carburetor. The CLOSED position enriches the fuel mixture for starting a cold engine.
CONTROLS & FEATURES Shift Lever Forward and reverse directions can be selected by shifting the shift lever. The lever will remain in any designated position. Actual movement of the snow blower takes affect when the drive clutch lever is engaged. Set the lever in ‘‘N’’ (Neutral) when the snow blower is not in use and when starting.
CONTROLS & FEATURES Drive Clutch Lever Depress the drive clutch lever to move the snow blower forward or backward based on the position of the shift lever (see previous page). When transporting the snow blower, depress the drive clutch lever without the auger clutch lever. DRIVE CLUTCH LEVER DRIVE CLUTCH DISENGAGE DISENGAGED ENGAGE ENGAGED Auger Clutch Lever Depress the auger clutch lever to start the snow blowing mechanism.
CONTROLS & FEATURES When both levers are depressed, the drive clutch lever locks the auger clutch lever down. Releasing the drive clutch lever then unlocks and releases the auger clutch lever. DRIVE CLUTCH LEVER LOCKED Both levers depressed The auger clutch lever remains locked down as long as one hand continues to depress the drive clutch lever. Steering Control Levers The steering control levers are located under the handlebar grips.
CONTROLS & FEATURES Pull the left steering control lever against the handlebar to turn the snow blower to the left. LEFT TURN Pull the right steering control lever against the handlebar to turn the snow blower to the right. RIGHT TURN Do not partially engage or release the steering control levers. Always fully engage or fully release the levers. Pull both steering control levers at the same time to momentarily disengage the transmission.
CONTROLS & FEATURES Height Adjust Lever (AT, ATD) Use the infinitely variable height adjust lever to change the height of the auger housing. 1.Hold the handlebar with both hands and depress the lever with your left thumb. 2.Move the handle up or down as needed to obtain the desired auger height position. 3.Release the lever to lock the height of the auger in position. • LOWER: Hard snow or fine finish • MIDDLE: Normal use • HIGHER: Deep snow or for transporting the snow thrower.
CONTROLS & FEATURES FEATURES LED Work Light LED WORK LIGHT The LED work light comes ON while the engine is running, and it goes OFF when the engine stops. The light does not come ON when the engine switch is turned ON unless the engine is started. Snow Clearing Bar If the snow discharge chute or snow blowing mechanism becomes restricted, stop the engine and make sure all rotating parts have come to a complete stop. Remove the spark plug cap from the spark plug.
CONTROLS & FEATURES Hour Meter HSS1332A (ATD only) The hour meter shows the accumulated engine running time of the snow blower. Use it as a guide for inspection or maintenance. When the engine switch is turned to the ‘‘ON’’ position, the total accumulated engine running time is shown. After starting the engine, the dot blinks and the engine running time starts to accumulate. HOUR METER DOT Five digits are provided to show running time (to 9,999.
CONTROLS & FEATURES Auger-Lock Indicator HSS1332A (ATD only) The auger-lock indicator comes on when the engine switch is turned to the ‘‘ON’’ position, then goes off after starting the engine. To prevent damage to the auger and/or auger transmission, the snow blower stops the engine and blinks the red auger-lock indicator under following conditions: AUGER-LOCK INDICATOR • A foreign object (for example: stone) is lodged in the rotating auger. • The auger contacts a curb.
BEFORE OPERATION ARE YOU READY TO GET STARTED? Your safety is your responsibility. A little time spent in preparation will significantly reduce the risk of injury. Knowledge Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the snow blower and its operation before you begin using it. Know how to quickly shut off the snow blower in case of an emergency.
BEFORE OPERATION Check the General Condition of the Snow Blower: • Before each use, look around and underneath the snow blower for signs of oil or gasoline leaks. • Check the auger housing and the discharge chute for accumulation of packed snow or ice. Clean the auger housing and discharge chute before starting the snow blower. • Look for signs of damage. • Check each control for proper operation. • Check the auger and blower for loose or broken bolts. If broken, replace them with new ones.
BEFORE OPERATION CHECK YOUR WORK AREA For your safety and the safety of others, always inspect the area before operating the snow blower. Objects Anything that can be picked up by the auger and thrown is a potential hazard to you and others. Thoroughly inspect the area where the equipment is to be used and remove all doormats, newspapers, sleds, boards, wires, stones, and nails from the work area.
OPERATION SNOW BLOWING PRECAUTIONS Before operating the snow blower for the first time, please review both the SNOW BLOWER SAFETY chapter (see page 5) and the BEFORE OPERATION chapter (see page 25). Even if you have operated other snow blowers, take time to become familiar with how this snow blower works, and practice in a safe area until you build up your skills. Never tamper with or alter any of the controls or safety devices on the snow blower. Tampering is a violation of Federal and California law.
OPERATION STARTING THE ENGINE N (NEUTRAL) 1.Move the shift lever to ‘‘N’’ (Neutral) position. SHIFT LEVER 2.Be sure that the drain knob is tightened securely. Turn the fuel valve to the ON position. ON DRAIN KNOB FUEL VALVE LEVER 3.In cold weather or when the engine is cold, pull the choke knob to the CLOSED position and move the throttle lever to the FAST position. FAST THROTTLE LEVER CLOSED CHOKE KNOB 4.Start the engine.
OPERATION Electric-start Models (ATD, AWD type) Turn the engine switch to the START position and release the switch after the engine has started. The switch automatically returns to the ON position. Do not operate the starter for more than one minute. If the engine fails to start, release the button and allow the starter to cool for 15 minutes before operating it again. Manual Starting only a. Turn the engine switch to the ON position. b.
OPERATION 5.Let the engine warm up for several minutes. If the choke knob has been pulled to the CLOSED position to start the engine, gradually push it to the OPEN position as the engine warms up. Move the throttle lever to the SLOW position. FAST SLOW OPEN CHOKE KNOB THROTTLE LEVER 6.While warming the engine up, also warm the transmission as follows: a. Check that the shift lever is in the ‘‘N’’ (Neutral) position.
OPERATION b. Squeeze the drive clutch lever for about 30 seconds to warm up the transmission fluid. DRIVE DRIVE CLUTCH LEVER CLUTCH DISENGAGE ENGAGE STOPPING THE ENGINE To stop the engine in an emergency, simply turn the engine switch to the OFF position. OFF Under normal conditions, use the following procedure.
OPERATION 1.Release the auger and drive clutch levers. The drive and snow blowing mechanism will stop operation. DRIVE CLUTCH LEVER AUGER CLUTCH LEVER 2.Move the shift lever to ‘‘N’’ (Neutral) position. N (NEUTRAL) SHIFT LEVER 3.Turn the throttle lever to the SLOW position.
OPERATION 4.Turn the engine switch to the OFF position. OFF ENGINE SWITCH 5.Turn the fuel valve lever to the OFF position.
OPERATION CLEARING SNOW 1.Move the throttle lever to the FAST position for normal operation. 2.Release the auger clutch lever, and move the shift lever to select the desired drive speed. Slower speed is recommended for removing deep or hardpacked snow. FAST N (NEUTRAL F (FORWARD) SLOW SLOW FAST R (REVERSE) FAST Faster speed is recommended for heavy wet snow conditions. 3.AT, ATD only: Set the auger height to the desired position (see page 21). SHIFT LEVER 4.
OPERATION 6.Depress the drive clutch lever to self-propel the snow blower. If the transmission shift lever (see page 35) is in the “F” (FORWARD) position, the hydrostatic drive will propel the snow blower forward when you squeeze the drive clutch lever. DRIVE CLUTCH LEVER Locked by drive clutch lever When both levers are depressed, the drive clutch lever locks the auger clutch lever down. This frees your right hand to operate the other snow blower controls.
OPERATION SNOW-CLEARING TIPS For best efficiency, clear snow before it melts, refreezes and hardens. Do not reduce engine speed while clearing snow. Operating tips for clearing hard or deep snow: • Reduce forward speed. If that is not sufficient, use the shift lever to clear snow with a back and forth motion. • Clear a narrower swath. Make several passes with the auger overlapping the cleared areas.
OPERATION REMOVING OBSTRUCTIONS If the snow discharge chute or snow blowing mechanism becomes restricted, review snow clearing tips (see page 37) to reduce the possibility of reoccurring obstructions. 1.Before removing the obstruction, be sure to stop the engine and ensure all rotating parts have come to a complete stop. Remove the spark plug cap from the spark plug. SNOW CLEARING BAR 2.Remove the snow clearing bar, or use a wooden stick to clear the obstruction.
SERVICING YOUR SNOW BLOWER THE IMPORTANCE OF MAINTENANCE Good maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution. To help you properly care for your snow blower, the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools.
SERVICING YOUR SNOW BLOWER MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Improper maintenance can cause an unsafe condition. Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed. Always follow the procedures and precautions in this manual.
SERVICING YOUR SNOW BLOWER TOOL KIT The tools necessary for performing some of the periodic maintenance, simple adjustments, and repairs are supplied in the tool kit. Spare shear bolts and nuts are also included in the tool kit.
SERVICING YOUR SNOW BLOWER MAINTENANCE SCHEDULE Every year REGULAR SERVICE PERIOD (1) Perform at every indicated month or operating hour interval, whichever comes first.
SERVICING YOUR SNOW BLOWER Every year REGULAR SERVICE PERIOD (1) Perform at every indicated month or operating hour interval, whichever comes first.
SERVICING YOUR SNOW BLOWER REFUELING With the engine stopped, remove the fuel tank cap and check the fuel level. Refill the tank if the fuel level is low. Do not fill above the base of the filler neck. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Keep heat, sparks, and flame away • Stop the engine and let it cool before refueling • Refuel only outdoors • Wipe up spills immediately FUEL TANK CAP FUEL GAUGE MAXIMUM FUEL LEVEL FUEL TANK TOP 1.
SERVICING YOUR SNOW BLOWER Never refuel the snow blower inside a building where gasoline fumes may reach flames or sparks. Keep gasoline away from appliance pilot lights, barbecues, electric appliances, and power tools. Spilled fuel is not only a fire hazard, it causes environmental damage. Wipe up spills immediately. Fuel can damage paint and plastic. Be careful not to spill fuel when filling your fuel tank. Damage caused by spilled fuel is not covered under warranty.
SERVICING YOUR SNOW BLOWER ENGINE OIL LEVEL CHECK Check the engine oil level with the engine stopped and in a level position. 1.Remove the oil filler cap. 2.Check the oil level. Do not thread the dipstick in when checking the oil level. If it is below the upper limit on the dipstick, fill with the recommended oil to the upper limit on the dipstick (see page 48). 3.Reinstall the oil filler cap securely. OIL FILLER CAP UPPER LIMIT Running the engine with a low oil level can cause engine damage.
SERVICING YOUR SNOW BLOWER ENGINE OIL CHANGE Drain the oil while the engine is still warm to assure rapid and complete draining. 1.Place the snow blower on a level surface. 2.Place a suitable container below the engine to catch the used oil, then remove the oil filler cap and the drain plug. To avoid loosening the drain plug extension, hold it with a 17 mm wrench while loosening the drain plug with a 10 mm wrench. DRAIN PLUG SEALING WASHER 3.
SERVICING YOUR SNOW BLOWER 4.With the engine in a level position, fill to the upper limit on the dipstick with the recommended oil (shown below). Do not thread the dipstick in when checking the oil level. Maximum oil capacity: 1.2 US qt (37 oz, 1.1 L) OIL FILLER CAP UPPER LIMIT Running the engine with a low oil level can cause engine damage. This type of damage is not covered by the Distributor’s Limited Warranty. 5.Reinstall the oil filler cap securely.
SERVICING YOUR SNOW BLOWER SPARK PLUG SERVICE Required spark plug: BPR5ES (NGK) or W16EPR-U (DENSO) Use only the required spark plug or equivalent. Spark plugs which have an improper heat range may cause engine damage. To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler. 1.Remove the spark plug cap. SPARK PLUG WRENCH 2.
SERVICING YOUR SNOW BLOWER 5.Measure the plug gap with a wire-type feeler gauge. Correct as necessary by carefully bending the side electrode. The gap should be: 0.028–0.031 in (0.7–0.8 mm) 6.Make sure that the spark plug sealing washer is in good condition, and thread the spark plug in by hand to prevent cross-threading. SIDE ELECTRODE 0.028–0.031 in (0.7–0.8 mm) SEALING WASHER INSULATOR 7.After the spark plug is seated, tighten with a spark plug wrench to compress the washer.
SERVICING YOUR SNOW BLOWER TRACK ADJUSTMENT Make sure the tracks are clean and dry before adjustment. The tracks cannot be correctly adjusted if clogged with snow or debris, or coated with ice. With the snow blower resting on its tracks, check track deflection by pressing down midway between the wheels with a force of 11 lbf (49 N). When correctly adjusted, track deflection should be: 7/16–5/8 in (11–16 mm) 11 lbf (49 N) 7/16–5/8 in (11–16 mm) TRACK Adjusting Procedure TENSION BOLT 1.
SERVICING YOUR SNOW BLOWER TIRE INSPECTION 1.Check the side wall and tread surface of each tire for cracks, damage, or excessive wear. 2.Check the tire pressure. Tire pressure: 20 psi (138 kPa) Excessive inflation pressure can damage the tires. Do not inflate the tires beyond the recommended pressure of 23 psi (159 kPa). AUGER AND BLOWER INSPECTION Check the auger, auger housing, blower, and shear bolts for signs of damage or other faults.
SERVICING YOUR SNOW BLOWER SHEAR BOLT REPLACEMENT Always use correctly sized replacement shear bolts. Use of bolts other than correctly sized shear bolts can cause damage to your snow blower. 1.Place the snow blower on a firm, level surface. 2.Turn the engine switch OFF, and remove the cap from the spark plug. 3.Clean the auger and blower of snow, ice, or any other foreign particles. 4.Check the entire snow clearing mechanism. 5.Replace any broken shear bolts. Tighten securely.
SERVICING YOUR SNOW BLOWER SKID SHOES AND SCRAPER To service, turn the engine switch to the OFF position and disconnect the spark plug cap so the engine cannot be accidentally started while you are near the auger. The skids are installed on the rear of the auger housing for track models (AT, ATD) and on the side for wheel models (AW, AWD). Loosen the bolts to move the skids, and then set the skids to the convenient position and tighten the bolts securely.
SERVICING YOUR SNOW BLOWER 4.After adjusting, raise the auger off the ground and then slowly lower and make sure both skid shoes contact the ground at the same time. Auger clearance: Ordinary snow conditions Smooth, ice-covered surfaces Rough or uneven surfaces 5/32–5/16 in (4.0–8.0 mm) 0–3/16 in (0–5.0 mm) 1–1-3/16 in (25.0–30.0 mm) Operation on rough or uneven surfaces with less than the recommended auger ground clearance can damage the snow blower. 5.
STORAGE STORAGE PREPARATION Proper storage preparation is essential for keeping your snow blower trouble-free and looking good. The following steps will help to keep rust and corrosion from impairing your snow blower’s function and appearance, and will make the engine easier to start when you use the snow blower again. Cleaning 1.Rinse the auger housing and wheels (or tracks) with a garden hose. Wipe the rest of the snow blower with a moist rag.
STORAGE Fuel Depending on the region where you operate your equipment, fuel formulations may deteriorate and oxidize rapidly. Fuel deterioration and oxidation can occur in as little as 30 days and may cause damage to the carburetor and/or fuel system. Please check with your servicing dealer for local storage recommendations. Gasoline will oxidize and deteriorate in storage. Old gasoline will cause hard starting, and it leaves gum deposits that clog the fuel system.
STORAGE Adding a Fuel Stabilizer to Extend Fuel Storage Life When adding a fuel stabilizer, fill the fuel tank with fresh gasoline. If only partially filled, air in the tank will promote fuel deterioration during storage. If you keep a container of gasoline for refueling, be sure that it contains only fresh gasoline. Add fuel stabilizer following the manufacturer’s instructions.
STORAGE Draining the Fuel Tank and Carburetor 1.Place an approved gasoline container below the carburetor, and use a funnel to avoid spilling fuel. 2.Loosen the carburetor drain knob, then move the fuel valve lever to the ON position. Drain the carburetor until the fuel tank is empty. DRAIN KNOB Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Keep heat, sparks, and flames away. • Handle fuel only outdoors. • Wipe up spills immediately. 3.
STORAGE Engine Oil 1.Change the engine oil (see page 47). 2.Remove the spark plug (see page 49). 3.Pour a teaspoon (5 cc) of clean engine oil into the cylinder. 4.Pull the starter rope slowly several times to distribute the oil. 5.Reinstall the spark plug. 6.Pull the starter grip slowly until you feel resistance, then return the starter grip gently. This will close the valves so moisture cannot enter the engine cylinder. Tires Check the air pressure (see page 52).
STORAGE Battery Removal/Charging/Installation (ATD, AWD) A commercially available 12 V battery charger should be used that can be adjusted to deliver 2 amps or less. An automatic battery charger is recommended (see page 73). 1.Remove the battery cover by first pulling the battery strap from the bottom hook. Pull the cover upward to unsnap the two cover pins. BATTERY COVER BATTERY STRAP COVER PINS 2.
STORAGE 3.To remove the battery, remove the battery strap from the bottom hook. 4.Connect the battery charger positive (+) cable to the battery positive (+) terminal and then connect the battery charger negative (–) cable to the battery negative (–) terminal. 5.Charge the battery: 5–10 hours at 1.2 A (HSS928A) 5–10 hours at 1.8 A (HSS1332A) 6.Install the battery in the reverse order of removal. 7.
STORAGE STORAGE PRECAUTIONS If your snow blower will be stored with gasoline in the fuel tank and carburetor, it is important to reduce the hazard of gasoline vapor ignition. Select a well-ventilated storage area away from any appliance that operates with a flame, such as a furnace, water heater, or clothes dryer. Also avoid any area with a spark-producing electric motor, or where power tools are operated. If possible, avoid storage areas with high humidity, which promote rust and corrosion.
TRANSPORTING BEFORE LOADING 1.Loading the snow blower on a trailer should be performed on a firm, level surface. 2.Use a loading ramp that is strong enough to support the combined weight of the snow blower and the operator. Weight of snow blower (operating weight): Types AT ATD AW AWD Models HSS928A 276 287 243 254 lbs lbs lbs lbs (125 (130 (110 (115 HSS1332A kg) kg) kg) kg) 287 lbs (130 kg) 309 lbs (140 kg) — — 3.The loading ramp must be long enough so that its slope is 15° (26%) or less.
TRANSPORTING LOADING 1.Track type: Raise the auger to the HIGH position (see page 21). 2.Start the engine and maneuver the snow blower backward into line with the loading ramp. 3.Track type: Run the snow blower backward slowly up the loading ramp. Wheel type: Push down the handles to raise the auger and run the snow blower up the loading ramp. Be careful to avoid striking the chute or other parts of the machine. BACKWARD 5 ft (1.5 m) minimum headroom DOWN UP H L 4.
TRANSPORTING Track models: Lower the auger housing so the skids rest on the vehicle floor. Do not tie with rope or straps stronger than necessary to prevent damage to the snow blower.
TAKING CARE OF UNEXPECTED PROBLEMS ENGINE PROBLEMS Starter operates, but engine will not start Possible cause Throttle not in proper position. Fuel valve is OFF. Sediment cup obstructed. Stale or old fuel. Spark plug cap off. Improper electrode gap or deposits in the spark plug gap. Correction Throttle must be in FAST position, choke OFF for a hot start, choke ON for a cold start. Turn fuel valve lever to ON (see page 15). Check for contaminates in sediment cup (see page 59). Be sure tank has fresh fuel.
TAKING CARE OF UNEXPECTED PROBLEMS Engine has low power (continued) Possible cause Spark plug cap not secure. Improper electrode gap or deposits on the electrodes. Choke in wrong position or choke plate sticking. Stale or old fuel. Correction Make sure spark plug cap is securely connected. Verify the spark plug is free of deposits and has the proper gap. Check choke plate movement. Add fresh fuel. Drain carburetor and sediment cup (page 59).
TAKING CARE OF UNEXPECTED PROBLEMS Snow not discharging properly Possible cause Auger spinning too slowly. Wet, deep snow is difficult to blow. Belt worn, not on pulleys or not properly installed. Snow blower moving too fast for snow conditions. Correction Keep throttle in FAST position (page 14). Reduce snow blowing swath or speed. See servicing Honda snow blower dealer. Use shift lever to reduce ground speed (page 17).
TECHNICAL INFORMATION Serial Number Locations Record the engine and frame serial numbers in the spaces below. You will need these serial numbers when ordering parts, and when making technical or warranty inquiries (see page 78).
TECHNICAL INFORMATION Carburetor Modification for High Altitude Operation At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting. Operation at an altitude that differs from that at which this engine was certified, for extended periods of time, may increase emissions.
TECHNICAL INFORMATION Emission Control System Information Source of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon monoxide does not react in the same way, but it is toxic.
TECHNICAL INFORMATION Problems That May Affect Emissions If you are aware of any of the following symptoms, have your engine inspected and repaired by your authorized Honda servicing dealer.
TECHNICAL INFORMATION Air Index An Air Index Information hang tag/label is applied to engines certified to an emission durability time period in accordance with the requirements of the California Air Resources Board. The bar graph is intended to provide you, our customer, the ability to compare the emissions performance of available engines. The lower the Air Index, the less pollution. The durability description is intended to provide you with information relating to the engine’s emission durability period.
TECHNICAL INFORMATION Specifications Frame Model HSS928A Type Items Description code Overall length Overall width Overall height Handlebar height Dry mass [weight] Width of snow clearance Height of snow clearance Snow throwing distance (varies with snow conditions) Clearing capacity AT ATD 28.9 in 37.0 in 265 lbs (120 kg) AW AWD SADA 58.5 in (1,485 mm) (735 mm) 30.5 in (775 mm) 43.5 in (1,105 mm) (940 mm) 36.6 in (930 mm) 276 lbs 231 lbs 243 lbs (125 kg) (105 kg) (110 kg) 28.0 in (710 mm) 21.
TECHNICAL INFORMATION Frame Model HSS1332A Items Description code Overall length Overall width Type Overall height Handlebar height Dry mass [weight] Width of snow clearance Height of snow clearance Snow throwing distance (varies with snow conditions) Clearing capacity AT ATD SAFA 58.5 in (1,485 mm) 32.9 in (835 mm) 43.5 in 48.4 in (1,105 mm) (1,230 mm) 37.0 in (940 mm) 276 lbs (125 kg) 298 lbs (135 kg) 31.9 in (810 mm) 21.7 in (550 mm) Max.
CONSUMER INFORMATION Dealer Locator Information To find an authorized Honda Servicing Dealer anywhere in the United States, visit our website at powerequipment.honda.com and click on Dealer Locator. Honda Publications Shop Manual This manual covers complete maintenance and overhaul procedures. It is intended to be used by a skilled technician. Visit our website at powerequipment.honda.com and click on Product Support.
CONSUMER INFORMATION Customer Service Information Honda Power Equipment dealership personnel are highly trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership’s management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
CONSUMER INFORMATION REPLACEMENT PARTS, OPTIONAL EQUIPMENT, AND SERVICE ITEMS Contact an authorized Honda servicing dealer to purchase any of these (or other) Honda Genuine items for your snow blower. Replacement Parts Item Part Number Notes Spark plug 98079-55846 NGK - BPR5ES Shear bolt 90121-V45-A00 90119-V45-A00 Blower 6 x 18 (carriage type) Auger 6 x 18 Fuse 98200-40500 5 Amp Optional Equipment Item Part Number Notes Cover See your local dealer.
DISTRIBUTOR’S LIMITED WARRANTY Honda Power Equipment This warranty is limited to the following Honda Power Equipment products when distributed by American Honda Motor Co., Inc., Power Equipment Division, 4900 Marconi Drive, Alpharetta, Georgia 30005. The following warranty applies to products purchased at retail or placed in rental service on or after January 1, 2010.
DISTRIBUTOR’S LIMITED WARRANTY Exclusions: 1.
EMISSION CONTROL SYSTEM WARRANTY Your new Honda Power Equipment engine complies with the U.S. EPA, Environment Canada, and State of California (models certified for sale in California only) emission regulations. American Honda Motor Co., Inc. provides the emission warranty coverage for engines in the United States and its territories. Honda Canada Inc. provides the emission warranty for engines in the 13 provinces and territories of Canada.
EMISSION CONTROL SYSTEM WARRANTY You are responsible for presenting your power equipment engine to a Honda Power Equipment dealer as soon as a problem exists. The emission related warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your emission warranty rights and responsibilities, you should contact the Honda office in your region: American Honda Motor Co., Inc.
EMISSION CONTROL SYSTEM WARRANTY TO OBTAIN WARRANTY SERVICE: You must, at your own expense, take your Honda Power Equipment engine or the product on which it is installed, along with your sales registration card or other proof of original purchase date, to any Honda Power Equipment dealer who is authorized by Honda to sell and service that Honda product during their normal business hours.
EMISSION CONTROL SYSTEM WARRANTY EMISSION CONTROL SYSTEM WARRANTY PARTS: SYSTEMS COVERED BY THIS WARRANTY: Fuel Metering PARTS DESCRIPTION: Carburetor assembly (includes starting enrichment system), Oxygen sensor, Throttle body, Engine temperature sensor, Engine control module, Fuel injector, Fuel regulator, Intake manifold Evaporative Fuel tank, Fuel cap, Fuel hoses, Vapor hoses, Carbon canister, Canister mounting brackets, Fuel strainer, Fuel valve, Fuel pump, Fuel hose joint, Canister purge hose joint E
NOTES 86
NOTES 87
NOTES 88
Inside back cover.ai 1 3/22/2016 12:34:15 PM QUICK REFERENCE INFORMATION C Fuel Type Unleaded gasoline with an ethanol content of no more than 10% and a pump octane rating of 86 or higher Engine Oil Type SAE 5W-30 API SJ or later for general use Maximum oil capacity: 1.2 US qt (37 oz, 1.1 L) Spark Plug Type BPR5ES (NGK) W16EPR-U (DENSO) Tires Tire Pressure 20 psi (138 kPa) Maintenance Before each Engine oil level. use, check the Tire air pressure. following. Auger skid shoes and scraper.
Rear Cover.ai 1 3/22/2016 12:33:46 PM C M Y CM MY CY CMY K © 2016 American Honda Motor Co., Inc. —All Rights Reserved Printed on Recycled Paper HPE.2016.05 PRINTED IN U.S.
