ENEN Owner’sManual Manual Owner’s OriginalInstructions Instructions Original Honda Honda Robotic Robotic Lawnmower Lawnmower HRM310/520 HRM310/520 VP7Z.
VP7Z.
Congratulations on your selection of a Honda Robotic Lawnmower. We are confident that you will enjoy the benefit of your Honda Robotic Lawnmower as we take great pride in creating the finest quality lawn care products. We want to help you get the best results from your new robotic lawnmower and to operate it safely. This manual contains all the information on how to do that; please read it carefully.
CONTENTS Setting Safety Instructions Preparation Menu Settings - Component identification (M page 10) - Installation (M page 12) - Setting up the lawnmower (M page 14) - Setting the work timer (M page 26) - Setting the lawnmower operation (M page 30) - Checking the system (M page 42) - Viewing history (M page 45) - Setting the system (M page 48) Operation Usage Work (Auto) - According to settings, the lawnmower works automatically.
1 OVERVIEW.................................................................................................................4 How the Honda Robotic Lawnmower works.........4 Features........................................................ 4 2 SAFETY INSTRUCTIONS..........................................................................................6 Precautions..................................................6 Label locations.............................................
How the Honda Robotic Lawnmower works / Features 1 OVERVIEW How the Honda Robotic Lawnmower works Configuring the system The mowing area is determined by the boundary wire that emits a signal; when the lawnmower detects the boundary it turns and it cuts the grass randomly. When battery starts running out, it goes back to the docking station. Transformer The transformer must be installed in a shaded area protected from rain. Docking station More than 1m More than 2m Pegs Features 4 VP7Z.
How the Honda Robotic Lawnmower works / Features Laying boundary wire 1 OVERVIEW The boundary wire location determines the parameters of the mowing area, this area may consist of multiple sections in which the lawnmower can operate. For mowing start point setup and detailed information please see “4 MENU SETTINGS” (M page 24). Do not lay boundary wire so that it intersects on a slope of more than 10° (17%).
Precautions 2 SAFETY INSTRUCTIONS Precautions Carefully observe the following precautions. • Make sure to keep your hands, feet and any other body parts away from the rotating blades. • Do not touch sharp components such as the blades or blade disc other than when performing maintenance. If you do, you may be injured. • Always press the manual STOP button first before you physically interact with the lawnmower such as lifting, turning sideway or upside down.
Precautions / Observe the following points for your safety • Do not charge the lawnmower with anything other than the docking station. An accident may occur or the lawnmower may be damaged. • If the power supply cord is damaged, immediately stop using the system and contact your servicing dealer. 2 SAFETY INSTRUCTIONS • If there are any holes (such as rabbit holes, etc.) in the work area, fill them in so that the work area is level. Periodically check the work area for holes.
Observe the following points for your safety • Observe the following points when touching the power outlet (House), power cord, and transformer. If you do not, you may be electrocuted. -- Do not touch the power outlet (House), cord, and transformer with wet hands. -- Do not touch the power outlet (House), cord, and transformer if the power outlet (House), power cord, or transformer is wet. -- If the transformer cable insulation is broken, immediately stop work and consult your dealer.
Label locations Label locations 2 SAFETY INSTRUCTIONS POSITIONING OF SAFETY LABELS Your lawnmower should be used with due care and attention. Therefore, figured labels have been placed on various parts of the machine to remind you of the main precautions to be taken. Their full meaning is explained later on. These labels are an integral part of the lawnmower and so, if any of them should become detached or illegible, contact your servicing dealer for their replacement.
Component identification 3 PREPARATION Component identification Body Top view Bottom view Height adjustment dial Charging socket Front (caster) wheels (Ï2) Blade disc Manual STOP button Blades (Ï3) When you press the manual STOP button, the control panel cover pops up.
Component identification Control panel Up/down arrow buttons Press to navigate to the previous/ next item in the display. Display The home screen and menus can be seen here while the lawnmower is turned on. On button Press to turn on the power. Off button Press to turn off the power. Enter button Press to enter your selection in the display. NOTE: - The timer does not function if you turn off the power.
Installation Installation We strongly recommend that an authorised Honda dealer performs the installation of your Robotic Lawnmower. Installation by an authorised Honda dealer will ensure that your system is working correctly. Checking conditions for installation Check with the dealer that performed the installation if the docking station and boundary wire are installed according to the conditions below. Also periodically confirm that these conditions are still met.
Installation Conditions for laying the boundary wire Image Condition Height of objects which the lawnmower might run on top of Crossed The boundary wire entry and exit points for a round area should be separated by less than 5 mm. (However, the boundary wire should not cross itself.) 3 PREPARATION Maximum 5 mm interval Lay boundary wire around objects which the lawnmower might run on top of (e.g. rocks, tree roots, etc.); these objects must be removed from the work area.
Setting up the lawnmower Setting up the lawnmower When turning the lawnmower on initially, the initial settings and setup wizard will appear. Through the initial settings, you can configure the display language, internal date and time, and create your PIN (Personal Identification Number). Through the setup wizard, you can configure the settings for the mowing operation of your lawnmower. NOTE: - If your dealer already configured the setup wizard, the setup wizard screen is not displayed.
Setting up the lawnmower Initial settings When turning the lawnmower on initially, the initial settings will appear to set the display language, internal date and time, and create your PIN (Personal Identification Number). N WARNING - Make sure to press the manual STOP button before performing the following procedure. Select your preferred language and press the H button.
Setting up the lawnmower Configuring the settings through the setup wizard The setup wizard will guide you to configure the settings for your mowing operation as follows: Menu name Usage Configuring and testing the settings [1.Garden layout] For configuring the settings related to the layout of the boundary wire. These setting values are referred from the other settings.
Setting up the lawnmower 1- 1- Select [Clockwise(CW)] or [Anticlockwise(ACW)] referring to the layout of your docking station and boundary wire, and press the H button. 4 Select [NEXT] and press the H button. 5 Enter the values of the boundary wire length and garden size. NOTE: - For details on the boundary wire length or garden size, contact your dealer. - Input the boundary wire length exactly because the values which are automatically configured are associated with the boundary wire length.
Setting up the lawnmower 2. Setting the mowing start points Through this setting, you can set the starting point to operate the lawnmower. If you set the mowing start points and combine them with the settings of work timer, you can effectively mow your garden. 2- 2- 1 Select [2.Mowing start points] and press the H button to configure the mowing start points. Setup wizard 2 Select [Yes] or [No] to the question on the addition of the start points and press the H button.
Setting up the lawnmower 3. Testing the Start points Through this testing, you can check the start points which you added in [2.Mowing start points]. NOTE: - Perform each test when the lawnmower is connected to the docking station. 1 Select [3.Test start points] and press the H button to check the start points. Setup wizard 3- 2 Select a start point number and press the H button. The information of the selected start point is displayed.
Setting up the lawnmower 3- 6 Select [Yes] or [No] to the question of the test result and press H button. If you select [Yes], go to step 3-7. If you select [No], the message “Do you want to modify the start point?“ is displayed and you can modify the start point settings. NOTE: - For details on the start point settings, see step 2-3 of “2. Setting the mowing start points” (M page 18). 7 Close the control panel cover. The lawnmower returns to the docking station.
Setting up the lawnmower 4. Setting the work timer Through this setting, you can configure the work day and work time to operate the lawnmower. 4- Select [4.Work timer] and press the H button to configure the work day and work time. Setup wizard 2 Select [1. Auto fill up timer] or [2. Manual setup] and press the H button. Wo r k t i m e r Recommended Menu name Description [1.
Setting up the lawnmower 4- 4- 4 If you select [1.Auto fill up timer] in step 4-2, confirm the days which are automatically configured referring to the boundary wire length and garden size. If you want to change the work time, select the day and press the H button to change the work time of the lawnmower. If you select [2.Manual setup] in step 4-2, select the day and press the H button to change the work time of the lawnmower.
Setting up the lawnmower 4- 12 Select your region and press the H button. Wo r k t i m e r Select your region. 7/7 1.North 2.North Central 3.South Central 4.South 13 Confirming a percentage of each month, select [NEXT] and press the H button. NOTE: - You can modify the values for operating the lawnmower. - According to the mowing results with the settings which are automatically configured by the system, it may be necessary to adjust the values for operating the lawnmower.
Menu overview 4 MENU SETTINGS The control panel menus are used to set how the lawnmower operates. Menu overview NOTE: - We recommend having your dealer change these settings during installation. Menu screen Selecting [Menu] in the home screen and press the H button, Menu screen is displayed as below: Selectable menu items Menu 1 . Wo r k t i m e r 2.Garden setup 3.Diagnostics 4.History 5.System settings 6.Setup wizard 17:01 Fr i The menu consists of multiple levels of submenus.
Menu overview Full menu diagram Menu Work timer Work timer MON/TUE/WED/THU/FRI/SAT/SUN 1 From/To (Input value) 2 From/To (Input value) Mowing start points MON/TUE/WED/THU/FRI/SAT/SUN Point 1/2/3/4/5 Seasonal timer Modify timer Deactivate Quiet timer Garden setup Auto mode JAN/FEB/MAR/APR/MAY/JUN/ JUL/AUG/SEP/OCT/NOV/DEC (Input value) Blade speed Low/Normal Wheel speed Low/Normal (Select level) Timer (Input value) Mowing start points : This indicates that the item can be set through the
Setting the work timer Setting the work timer You can set the work day and work time for the lawnmower to operate. You can also specify a specific area for each work time. Work timer You can select the day and time on which you want the lawnmower to operate. Menu screen Home screen J [1.Work timer] J [1.Work timer] Configure this setting to have the lawnmower operate on specific days and times. You can set up to two times for operation for one day.
Setting the work timer Mowing start points You can set the mowing start points for each day of week. For example, if you set the following 5 start points in your garden, you enable the lawnmower to reach other areas through narrow passages and mow your garden effectively.
Setting the work timer Seasonal timer The growth speed of lawn depends on the season. With this function, you can configure the ratio of the mowing time for each season. Menu screen Home screen J [1.Work timer] J [3.Seasonal timer] J [1.Modify timer] Configure this setting to have a percentage of each month of lawnmower operation.
Setting the work timer Quiet timer You can set the blade speed, wheel speed and timer for operating the lawnmower quietly. Menu screen Home screen J [1.Work timer] J [4.Quiet timer] (“ON” is checked) Configure this setting to operate the lawnmower with low noise during the period which you configure. Set a start time and an end time for configuring the time for the quiet operation. 2 Press the H button.
Setting the lawnmower operation Setting the lawnmower operation Auto mode You can set up the lawnmower operation as follows: Setting the angle to turn from the boundary wire When leaving the boundary wire, set the angle to turn from the boundary wire. Setting the distance to the start point Until the lawnmower reaches a set starting point in an area, it will run without mowing. L Angle settings in [1.Mowing start points] (M page 32) L Distance settings in [1.
Setting the lawnmower operation Distance from the boundary wire when the lawnmower goes toward the mowing start points: The lawnmower moves between the boundary wire and the specified value at random as it goes toward the mowing start point. Narrow passage Low value Low value Value is too high NOTE: - When the value is too high, lawnmower may not pass through narrow passage.
Setting the lawnmower operation Mowing start points Menu screen Home screen J [2.Garden setup] J [1.Auto mode] J [1.Mowing start points] J [1.Point 1] to [5.Point 5] The lawnmower travels to this location along the boundary wire, and then turns away from the boundary wire to begin mowing. This allows you to send the lawnmower to an area which is difficult to access. TIPS Don’t make the distance value bigger than it needs to be. This will maximise the cutting time.
Setting the lawnmower operation Menu screen Home screen J [2.Garden setup] J [1.Auto mode] J [2.Mowing pattern] J [1.Point 1] to [5.Point 5] You can select from 3 mowing patterns below: [Directional] With the [Directional] setting, when the lawnmower detects the boundary wire, it turns at a narrow angle. This is used for mowing narrow areas. 4 MENU SETTINGS [Random] With the [Random] setting, when the lawnmower detects the boundary wire, it turns at a wide angle.
Setting the lawnmower operation Menu screen Home screen J [2.Garden setup] J [1.Auto mode] J [3.Advanced setting] J [2.Edge cutting] With this function, you can mow the unmown area along the boundary wire. If the edge cutting setting is enabled, the lawnmower goes around your garden along the boundary wire to mow the edge before starting the usual mowing. If you set this function on, the lawnmower mows along the boundary wire when the work timer starts for the first time on selected day(s).
Setting the lawnmower operation Menu screen Home screen J [2.Garden setup] J [1.Auto mode] J [3.Advanced setting] J [3.Spiral cutting] With this function, the lawnmower can be focused on mowing the area where the lawn is not completely mown, or the growth speed of the lawn is fast. The lawnmower detects the dense area and mow there spirally. Select [ON] or [OFF] for configuring the spiral cutting, and press the H button. If you select [ON], go to step 2.
Setting the lawnmower operation Menu screen Home screen J [2.Garden setup] J [1.Auto mode] J [3.Advanced setting] J [4.Narrow passage] If there are narrow passages on your garden, you can configure the settings of the narrow passages to let the lawnmower pass through them toward the starting point. End of the narrow passage Start of the narrow passage A B B : Distance between the docking station and the end of the narrow passage.
Setting the lawnmower operation Manual mode With this function, you can configure the lawnmower to mow without the work timer function. NOTE: - If you want to operate the lawnmower with [Manual mode], see “Operating the lawnmower with the Manual mode” (M page 70) Mowing pattern 4 MENU SETTINGS You can select from 3 mowing patterns below: [Directional] With the [Directional] setting, when the lawnmower detects the boundary wire, it turns at a narrow angle. This is used for mowing narrow areas.
Setting the lawnmower operation Menu screen Home screen J [2.Garden setup] J [2.Manual mode] You can adjust how the lawnmower moves while mowing. NOTE: - If you want the lawnmower to operate with the manual mode, change the operating mode by pressing the D button. For details, see “5 USAGE” (M page 52). - Among the mowing pattern settings, the [Mixed] setting is also available.
Setting the lawnmower operation Set the edge cutting and select the days on which you want the lawnmower to operate with this function. 17:01 Fr i Manua l m o d e s e t u p Edg e c u t t i n g O N OFF Select d a y s MON TUE WED THU FRI SAT S U N Fi n i s h Garden layout 4 MENU SETTINGS Menu screen Home screen J [2.Garden setup] J [3.Garden layout] J [1.Docking direction] You can set the direction for the lawnmower to move in relation to the docking station.
Setting the lawnmower operation Homing setup Menu screen Home screen J [2.Garden setup] J [4.Homing setup] J [1.Passage width] You can set where the lawnmower moves in relation to the boundary wire as it goes back to the docking station. NOTE: - This setting must be set to a value lower or equal than the lowest width value that is set for any mowing start point setting. For details on the mowing start point settings, see “Mowing start point” (M page 32). 1 Enter a number setting.
Setting the lawnmower operation Menu screen Home screen J [2.Garden setup] J [4.Homing setup] J [2.Capacity for homing] You can set the percentage of remaining amount of the battery when the lawnmower starts to go back to the docking station. TIPS The longer the wire is, the higher this value 1 Select [Auto] or Enter a percentage of battery residual capacity. The range of the percentage of battery residual capacity is 10 – 50%. 2 Press the H button. 4 MENU SETTINGS should be.
Checking the system Checking the system Check signal You can check if the boundary wire signal is correctly reaching the lawnmower and confirm how strong the signal is. Menu screen Home screen J [3.Diagnostics] J [1.Check signal] Signal level indication Signal strength Lv0 No loop signal Lv1 Weak Lv5 Moderate Lv10 Strong 42 VP7Z.
Checking the system Test start points You can check whether the lawnmower can correctly return to the docking station, and whether it can reach each start points according to settings. Menu screen Home screen J [3.Diagnostics] J [2.Test start points] J [1.Point1] to [5.Point5] NOTE: - Perform this test when the lawnmower is connected to the docking station. 1 2 Confirm the value of the selected point settings. 3 Select [Yes] and press the H button.. 4 Close the control panel cover.
Checking the system Menu screen Home screen J [3.Diagonostics] J [2.Test start points] J [0.Home] You can test if the lawnmower will correctly return to the docking station. NOTE: - Perform this test when the lawnmower is not connected to the docking station. 1 Select [Clockwise(CW)] or [Anticlockwise(ACW)]. 2 Press the H button. 3 Close the control panel cover. The lawnmower returns to the docking station. 4 When the lawnmower is docked at the docking station, press the manual STOP button.
Viewing history Viewing history Operation history You can check the cumulative time that the lawnmower has operated and recharged. Menu screen You can view how long the lawnmower has mowed, and how long the lawnmower has charged. 1 Check the history. 2 Press the G button to return to the previous screen. Operating time This is the total cutting time. This is the total charging time. Cutting Charging 17:01 4 MENU SETTINGS Home screen J [4.History] J [1.Operating history] J [1.
Viewing history Work history Menu screen Home screen J [4.History] J [1.Operating history] J [2.Work history] You can view the lawnmower’s cutting history (when the lawnmower was mowing), return history (when the lawnmower was returning to the docking station), and charge history (when the lawnmower was charging). 1 Check the history by pressing the up/ down arrow buttons to scroll the menu. 2 Press the G button to return to the previous screen. NOTE: - Only the history of auto mode is displayed.
Viewing history Fault history You can view the lawnmower’s fault history (when a fault occurred). Menu screen Home screen J [4.History] J [2.Fault history] NOTE: - If the same error occurs on the same day, only the time when the first error occurred is saved. The most recent fault error entry is displayed first. Press the H button for more information. Fault information and the time of the fault are displayed. Select fault history entry by using the up/ down arrow buttons. 2 Press the H button.
Setting the system Setting the system Language ABC You can set the menus of the display to your preferred language. Menu screen Home screen J [5.System settings] J [1.Language] Select the language shown in the display from among 5 languages. NOTE: - If you want to set other languages, contact your dealer. 1 Select your preferred language. 2 Press the H button. 3 Press the G button to return to the previous screen. Display/Sound Menu screen Home screen J [5.System settings] J [2.
Setting the system Menu screen Home screen J [5.System settings] J [2.Display/Sound] J [Keypad] You can set whether or not a beep sound is emitted when you press control panel buttons. Select [ON] or [OFF] by pressing the up/ down arrow buttons. 2 Press the H button. 3 Press the G button to return to the previous screen. 4 MENU SETTINGS 1 Date and Time You can set the internal date and time for the lawnmower. Menu screen Home screen J [5.System settings] J [3.
Setting the system Security Security settings are used to prevent the lawnmower from being operated by other people and stop the lawnmower from operating for a fixed period of time. Menu screen Home screen J [5.System settings] J [4.Security] J [1.Alarm] NOTE: - Before selecting [1.Alarm], you will need to input your PIN. This setting enables or disables the alarm. When set to [OFF], all alarms other than the alarm before the blades start moving are disabled.
Setting the system Factory reset You can reset all settings to the factory defaults. Menu screen Home screen J [5.System settings] J [5.Factory reset] Execute this command to revert all settings to their factory defaults. Input your PIN and press the H button. 2 Select [Yes]. 3 Press the H button. After the message “Activated” is displayed, the power turns off. 4 MENU SETTINGS NOTE: - This command will not reset the history of the lawnmower (working and fault history).
Checking the mowing area / Connecting to a power source 5 USAGE Checking the mowing area Before operating the lawnmower, ensure the mowing area is free of pets and foreign objects. CAUTION: - If there are any holes (such as rabbit holes, etc.) in the work area, fill them in so that the work area is level. Periodically check the work area for holes. Also confirm that the height of the grass is 65 mm or less. NOTE: - Adjust the height of the blades to mow the grass within 5 mm.
Checking the lawnmower / Turning on / off the power Checking the lawnmower Before operation, check to make sure that it is connected all the way into the docking station. The light above the charging plug changes as follows: Color Description Green The docking station signal setting is correct. Green (blinking) The boundary wire is too long. Amber The lawnmower is correctly connected to the docking station.
Turning on / off the power / Operating the lawnmower in Auto mode Turning off the power 1 Press the manual STOP button. The control panel cover pops up. 2 Press the B (Off) button on the control panel. NOTE: - When you turn off the lawnmower, it will not begin to operate even if you set the timer. Operating the lawnmower in Auto mode Entering your PIN (Personal Identification Number) When turning the lawnmower on, you must enter the PIN. 1 Enter the PIN using the number buttons.
Operating the lawnmower in Auto mode Auto mode operation These instructions can be used to operate the lawnmower at the time scheduled for the Auto mode settings. NOTE: - For details on settings, see “4 MENU SETTINGS” (M page 24). N WARNING - Make sure to press the manual STOP button before performing the following procedure. 1 Press the H button. 2 If the [Auto] is displayed on the Home screen, go to step 2.
Adjusting the height of the blades Adjusting the height of the blades The height of the blades determines how tall or short the grass will be cut. Test the lawnmower on a small area and adjust blade height according to your preference. N WARNING - Make sure to press the manual STOP button before performing the following procedure. CAUTION: - Avoid cutting too much at once. Mow gradually step by step (from level 5 to 1.) - Avoid cutting more than 5 mm of grass at once.
Adjusting the height of the blades / Weekly checks 4 Close the height adjustment dial cover, and close the control panel cover. Repeat the steps above if you need to make additional adjustments. Weekly checks Check the lawnmower and docking station once a week to remove dirt and grass. Also check if the blades and blade disc have been damaged, and verify that there are no other problems.
Carrying the lawnmower Carrying the lawnmower When carrying the lawnmower, observe the following points. N WARNING - Do not carry the lawnmower with the blades pointed toward you. - Take care to avoid dropping the lawnmower when carrying it. - Make sure to press the manual STOP button and turn the lawnmower off before performing the following procedure. - Make sure the lawnmower (especially the blades) does not touch anyone when you are carrying it. 1.
Before contacting your dealer / Messages 6 TROUBLESHOOTING Before contacting your dealer In the unlikely event that you are facing a problem and you need to contact your dealer, ensure that you have the following information available. • Owner’s Manual • Consider any recent work in your garden. • [Fault history] information Home screen J [4.History] J [2.
Messages / Resolving problems Message Cause Solution Outside loop The lawnmower exited the boundary wire. Move the lawnmower into the work area. Check the power supply of the docking station. Check if the boundary wire connectors are correctly connected. If the message does not disappear, check if the boundary wire connectors are correctly connected, and check if there are no similar lawnmowers in the area. If the message still does not disappear, contact your dealer.
Messages / Resolving problems Resolving problems Problem Solution Check the connections, and charge the lawnmower again. If the lawnmower cannot be charged, contact your dealer. The lawnmower will not enter an area, or the blades and movement have stopped. The lawnmower will try to evade an area with a slope of more than 20°.
Periodic inspection and maintenance / Maintenance procedures 7 MAINTENANCE Periodic inspection and maintenance The lawnmower must be periodically inspected and maintained for safety and to keep it running at a high level of performance. Periodic maintenance will also help to extend service life. The required service intervals and the kind of maintenance to be performed are described in the following chart. Honda recommends annual service to be completed by your local authorised Honda dealer.
Maintenance procedures Preparing Perform the following procedures in an area not subject to rainfall. Correct 90 degrees or less • Put on a pair of work gloves. • When checking the blades, turn the lawnmower on its side. Incorrect More than 90 degrees • Do not tilt the lawnmower over an angle of 90 degrees to prevent grass clippings or fluid from entering inside the lawnmower. Cleaning N WARNING - Do not touch the blades with your hands.
Maintenance procedures Cleaning the docking station N WARNING - Unplug the transformer’s plug from the power outlet (House) before cleaning it. Clean dirt and grass off of the docking station using a brush. Brush off dirt and grass from docking station, particularly around parts on which the lawnmower rests and around the charging plug area: Charging plug Checking Checking the manual STOP button N WARNING - Do not touch the blades with your hands.
Maintenance procedures Checking the docking station Check the docking station for problems. Check item(s) Action Docking station Damage to the docking station Visually inspect the docking station. If it is damaged, consult your dealer. Connectors Loosened connectors of the docking station Visually inspect the connectors. If they are loose, consult your dealer.
Maintenance procedures Checking the blades and blade disc Check the condition of the blades and blade disc as follows. Life time of the blades In order to have good cutting performance, maintain the sharp cutting edge on the blades. Typically, the life time of the blades is 160 hours.(2 weeks to 2 months) Because the life time depends on grass condition, it may be necessary to exchange earlier than usual, especially in the spring season.
Maintenance procedures Replacing the blades To replace the blades, perform the procedures below. N WARNING - Put on a pair of work gloves before performing the following procedures. NOTE: - This work requires technical skill and knowledge, as well as special tools. Consult your dealer if you cannot perform the procedures below. - To maintain uniformity, replace all 3 blades and their nuts during replacement. - Before replacing the blades, remove the grass clippings (M page 63) .
8 STORAGE Winter Storage Lawnmower and Docking station It is very important that your lawnmower and docking station is cleaned thoroughly before placing into storage. The battery should be charged before it is stored in a dry place away from frost and protected from the winter weather. Electrical Components It is strongly recommended that you disconnect the transformer and power cables over winter leaving only the boundary wire in the ground.
Specifications 9 TECHNICAL INFORMATION Specifications Model Description code Type EAE HRM310 HRM520 MBEF MBDF EAEN EAB EAS EAE Length 645 mm Width 550 mm Height 275 mm Weight EAEN EAB 11.6 kg 11.9 kg Li-ion 22.2 V / 1800 mAh Li-ion 22.2 V / 3600 mAh EAS Electrical system Battery Transformer Input AC 230 V AC 230 V AC 240 V AC 230 V AC 230 V AC 230 V AC 240 V AC 230 V Output 26.0 V / 2.
Manual mode operation 10 APPENDIX Operating the lawnmower with the Manual mode This setting can be used when 2 or more areas within the boundary wire are connected by a narrow path. If you have 2 or more areas within the boundary wire connected by a path that is less than 1 meter wide, the lawnmower cannot pass between them, and must be carried to the other area manually. Follow the steps below when performing this procedure.
Manual mode operation 10 Press the H button. 11 Press the G button to return to the Home screen. 12 Close the control panel cover. The lawnmower automatically begins to operate. NOTE: - The lawnmower does not turn off automatically when in manual mode. Canceling the Manual mode operation You can cancel the operation which you selected on the Manual mode screen and the lawnmower returns to the docking station. 1 Press the manual STOP button from behind the lawnmower.
Manual mode operation 8 Press the H button. The power turns on, and the startup screen on the control panel is displayed. 9 Press the G button to return to the Home screen. 10 Close the control panel cover. The lawnmower returns to the docking station. 72 VP7Z.
Major Honda Distributor Addresses Major Honda Distributor Addresses BALTIC STATES AUSTRIA (Estonia/Latvia/Lithuania) Honda Motor Europe Ltd Eesti filiaal Meistri 12 13517 Tallinn Estonia Tel. : +372 651 7300 Fax : +372 651 7301 E-mail : honda.baltic@honda-eu.com. Honda Austria Branch of Honda Motor Europe Ltd Hondastraße 1 2351 Wiener Neudorf Tel. : +43 (0)2236 690 0 Fax : +43 (0)2236 690 480 http://www.honda.at HondaPP@honda.co.
“EC Declaration of Conformity” CONTENT OUTLINE “EC Declaration of Conformity” CONTENT OUTLINE EC Declaration of Conformity 1.
“EC Declaration of Conformity” CONTENT OUTLINE Polski ( Polish ) Deklaracja Zgodności WE 1.
LCD MENU INDEX Menu name Step Page A Alarm Auto mode System settings → Security Garden setup → Auto mode P.50 P.30 B BG color System settings → Display/Sound P.48 C Check signal Contrast Create a PIN Diagnostics System settings → Display/Sound System settings → Security P.42 P.48 P.50 D Date and time Docking direction System settings Garden setup → Garden layout P.49 P.39 E Edge cutting Garden setup → Auto mode → Advanced setting P.
LAWN DIAGRAM 77 VP7Z.
DEALER CHECKSHEET The following information is provided by your dealer after setup is complete. Basic setting information (M pages 15, 50) PIN (Personal Identification Number): Language : English / Deutsch / Français / Italiano / Nederlands / Svenska / Norsk / Español / Polski / Dansk / Suomalainen / Čeština / Português Setup wizard setting information (M page 16) The following items are related to the basic settings for Setup wizard.
Other setting item information Please fill the following items if configuring them with the Menu settings. Garden layout setting information (M pages 32, 36, 39, 40) Passage width: Home screen J [2.Garden setup] J [1.Auto mode] J [1.Mowing start points] J [1.Point 1] to [5.Point 5] Point 1: Point 2: Point 3: Point 4: Point 5: Narrow passage: Home screen J [2.Garden setup] J [1.Auto mode]J [3.Advanced setting] J [4.
VP7Z.
QUICK GUIDE QUICK GUIDE Technical tips Fundamentals Turning on / off the power (M page 11, 53) Mowing mode Stopping the lawnmower (M page 10) Adjusting the cutting height (M page 56) Decrease Increase You can select from 2 modes of operation (available in “Menu Settings”). Auto mode (M page 30) The lawnmower automatically mows according to inputted time and garden settings. Manual mode (M page 37) Start mowing anytime without timer settings.
VP7Z.
VP7Z.
32VP7610 32VP7610 00X32-VP7-6100 00X32-VP7-6100 VP7Z.indb 2 Honda Motor Co., 2014 Honda Motor Co., Ltd.Ltd. 2014 xxxx.xxxx.xx xxxx.xxxx.xx xxxx.xxxx.xx xxxx.xxxx.
