Owner’s Manual SUBMERSIBLE PUMP WSP50 lWSPlOO I I I I I I I I I I I I I I I I I I I I I I i i i i i i i i i i i i i i i i i i i i i I
USE AND MAINTENANCE INSTRUCTIONS MANUAL 1.1 MANUFACTURER DATA EBARA INTERNATIONAL CORPORATION 1651 CEDAR LINE DRIVE ROCK HILL, SC 29730 1.2 PUMP DATA Description: Model: Year of manufacture: SUBMERSIBLE SOLIDS PUMP WSP5OAM, WSP50AA, WSPI OOAM, WSPI OOAA see plate on the pump. If the malfunction of the pump is not among those included in the troubleshooting table (chapter 14. I), contact the nearest appointed dealer.
7. TECHNICAL DATA CARD 7.1. Pump technical data 7.2. Motor technical data 8. RECOMMENDED AND NON-RECOMMENDED USES 8.1. Recommended conditions of use 8.2. Non-recommended conditions of use 9. HANDLING AND TRANSPORT 9.1. Unpacking 9.2. Handling and disconnecting 9.3. Transport 10. INSTALLATION 10.1. Fixed installation 10.2. Temporary installation 11. ASSEMBLY AND DISASSEMBLY 12. PREPARATION FOR USE 12.1. Electric connection 12.2. Adjusting and registering 13. USE AND STARTUP 73.1. Automatic Pumps 13.2.
FAILURE TO OBSERVE THESE WARNINGS AND /OR TAMPERING WITH THE PUMP RELIEVES THE MANUFACTURER OF ANY RESPONSIBILITY IN THE EVENT OF DAMAGE TO PERSONS OR OBJECTS AND/OR TO THE PUMP. Before starting the pump it is important for the user to know how to perform all the operations described in this manual and to apply them at all times during use or maintenance of the pump. 5.1.
.1 GENERAL DESCRIPTION WSPSO and WSPl 00 series pumps are all similar from the functional constructive point of view; the only differences are the following: and -power -flow rate -head -weight -dimensions WSP50 and WSPlOO series pumps are used for handling water, even at high temperatures (chapter 7.7). Thanks to their small bulk and ease of transport, they may be used for fixed or temporary installations, with or without automatic start.
.2. MOTOR TECHNICAL Power (Versions) DATA WSP5O/WSPlOO l/2 hp 7 hp 7% Poles Insulation class Degree of protection Type of duty Phase-frequency-voltage Overload .L F IP58 continuous single-phase 6OHz 775 thermal protection single-phase molded steel stainless steel sow-A/so protection Motor structure Shaft material Cable material material THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE TECHNICAL DATA IN ORDER TO MAKE IMPROVEMENTS AND BRING THEM UP-TODATE.
9.1. UNPACKING Check that there are no breaks or severe dents in the packing; if there are, point this out immediately to the person who delivers the material. After removing the pump from the package, check that it has not suffered any damage during transport; if damage is found, inform the dealer within 8 days of delivery. Then check that the characteristics stated on the plate of the pump are the same as you requested in your order. 9.2.
-ITO LIFT OR LOWER THE PUMP, USE A ROPE FIXED TO THE HANDLE; NEVER USE THE ELECTRIC POWER CABLE. 70.1. FIXED INSTALLATION a) The pump must be placed on a level surface. b) Lower the pump with a cable fixed to the handle. c) When positioning the pump, observe the minimum required distancesGig. from walls, from the sides of the drain or other location, so as to allow functioning, use and maintenance operations in safe conditions.
b) The outlet must have an efficient ground system complying with the electrical standards in force in the user’s country; the installer is responsible for checking this. c) The WSPSO and WSPlOO pumps have a plug with ground contact; grounding is provided by the plug itself when it is inserted in the socket. d) We advise fitting a higb-sensitivity differential switch in the electric system (0.03 A). The electric connection must be by a licensed technician. 12.2.
a) If the intake mouth is blocked it must be cleaned; always wear gloves to protect your hands. b) If the impeller is dirty proceed as follows (fig. 4): -wear protective gloves to avoid cutting your hands; -unscrew the six socket head screws (1) (not the nut, because it is welded to the pump body); -slip off the pump body (2); -remove the O-ring (3); -the impeller is now uncovered; check that it is clean; check also that the space between the impeller and the protective casing is clean.
TYPE OF FAULT The pump stops after brief periods of operation (tripping of the thermal protection) CAUSE REMEDY Impeller blocked by foreign bodies. Remove the foreign bodies (ch. 74). Be certain to disconnect power. Liquid temperature too high. The temperature exceeds the technical limits of the pump. Internal defect. Contact the nearest distributor.
15.1. DIAGRAM SPACES (fig.
15.2. WIRING DIAGRAM 15.3. WIRING 1 115v DIAGRAM 1 WSP50AA AND FOR WSP50AM Bmm, WSPIOOAA AND (fig. 2) WSPlOOAM (fig.
.4. DIAGRAM FOR PUMP IMPELLER COVER DISASSEMBLY 13 (fig.
Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership’s management. The Service Manager or General Manager can help. Almost all problems are solved in this way. If you are dissatisfied with the decision made by the dealership’s tact the Honda Power Equipment Customer Relations Office.
Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
III Ill 11 11 I I I 11 l . HONDA 00X31 -WSP-8000 I I I I Recycled Paper I I I PRINTED IN U.S.A.
