2020/3820/3820i Cordless System User’s Guide ™
Disclaimer Honeywell International Inc. (“Honeywell”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Honeywell to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Honeywell.
Product Agency Compliance USA FCC Part 15 Subpart C This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment.
c-UL Statement C-UL listed: CSA C22.2 No.60950-1-03, 2nd Edition for I.T.E. product safety. Europe The CE marking on the product indicates that this device is in conformity with all essential requirements of the 1999/5/EC R&TTE Directive. In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with recommended power supply. For CE-related inquiries, please contact: Honeywell Imaging & Mobility Europe BV International Inc.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration. You may also contact your supplier for more information on the environmental performances of this product. Germany If your product is marked with the GS symbol, then the product has been issued a GS certificate showing compliance to EN 60950-1, Second Edition. This device is not intended for use in direct field of view at visual display workplaces.
Brazil (3820i, 2020-5 Scanner and AP-010BT) This product is approved by Anatel, according to the procedures regulated by Resolution No. 242/2000 and meets the technical requirements applied. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução No. 242/2000 e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site da ANATEL – www.anatel.gov.
! • Do not disassemble or modify batteries. Caution: Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the recycle program for batteries as directed by the governing agency for the country where the batteries are to be discarded. LED Safety Statement Scanner LEDs have been tested and classified as “EXEMPT RISK GROUP” to the standard: IEC 62471:2006.
Required Safety Labels Scanner Compliance Label locations Item Number, Serial Number and Revision Information location
Base Compliance Label locations Item Number, Serial Number and Revision Information location
Table of Contents Chapter 1 - Getting Started About This Manual ...................................................... 1-1 Unpacking the System ................................................ 1-1 Models......................................................................... 1-1 Cordless System: Main Components .......................... 1-2 About the Battery ........................................................ 1-2 Proper Disposal of the Battery .............................. 1-3 Base Charge Mode .....
Beeper and LED Sequences and Their Meaning ...... 1-14 3820/3820i LED Sequences and Their Meaning . 1-15 2020 LED Sequences and Their Meaning ........... 1-15 Basic Operation of the Cordless System ................... 1-16 System Conditions ............................................... 1-17 Communication Between the Cordless System and the Host ................................................... 1-18 Connecting the Base When Powered by Host (Keyboard Wedge) ................................................
Connecting the Base with RS-232 Serial Port ............ 2-8 RS-232 Baud Rate ................................................ 2-9 RS-232 Word Length: Data Bits, Stop Bits, and Parity......................................................... 2-9 RS-232 Handshaking .......................................... 2-10 Host ACK Selection............................................. 2-11 Host ACK Enable ................................................ 2-12 Wand Emulation ..............................................
Output Sequence Overview....................................... 3-10 Output Sequence Editor ...................................... 3-11 Require Output Sequence ................................... 3-11 Multiple Symbols........................................................ 3-13 No Read..................................................................... 3-14 Video Reverse ........................................................... 3-14 Chapter 4 - Data Editing Prefix/Suffix Overview........................
Message Length.......................................................... 6-2 Codabar ...................................................................... 6-3 Codabar Start/Stop Characters ............................ 6-3 Codabar Check Character..................................... 6-3 Codabar Concatenation ........................................ 6-4 Codabar Message Length ..................................... 6-5 Code 39.......................................................................
UPC A........................................................................ 6-18 UPC A Check Digit .............................................. 6-18 UPC A Number System ....................................... 6-19 UPC A Addenda .................................................. 6-19 UPC A Addenda Required ................................... 6-19 UPC A Addenda Separator.................................. 6-20 UPC-A/EAN-13 with Extended Coupon Code ........... 6-20 UPC E0 and UPC E1........................
Korea Post Code ....................................................... 6-32 Korea Post Message Length ............................... 6-32 PosiCode A and B ..................................................... 6-32 PosiCode Message Length ................................. 6-33 Codablock F .............................................................. 6-34 Codablock F Message Length............................. 6-34 Code 16K ..................................................................
Menu Command Syntax ............................................ 10-1 Query Commands................................................ 10-2 Concatenation of Multiple Commands ................. 10-2 Responses ........................................................... 10-3 Examples of Query Commands ........................... 10-3 Trigger Commands .................................................... 10-4 Resetting the Standard Product Default Settings: Current Application Work Group ..........................
Chapter 13 - Customer Support Product Service and Repair ...................................... 13-1 Online Product Service and Repair Assistance... 13-2 Limited Warranty ................................................. 13-2 Appendix A - Reference Charts Symbology Chart......................................................... A-1 Code Page Mapping of Printed bar codes .................. A-6 Appendix B - Minimizing Bluetooth/ISM Band Network Activity Auto Reconnect Mode....................................
x
1 Getting Started About This Manual This manual contains information to help you set up, operate, and program the cordless system. Product specifications, connector pinouts, a troubleshooting guide, and customer support information are also provided. Honeywell bar code image scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.
Cordless System: Main Components Battery Contained in Handle About the Battery ! We recommend use of Hand Held Products Li-ion battery backs. Use of any non-Hand Held Products battery may result in damage not covered by the warranty. Power is supplied to the cordless image scanner by a rechargeable battery that is integrated in the image scanner handle. Each image scanner is shipped with a battery. (See Product Specifications beginning on page 11-1.
Battery Recommendations • Batteries are shipped approximately 30% to 60% charged and should be fully charged for maximum charge capacity. • The battery is a lithium ion cell and can be used without a full charge, as well as can be charged without fully discharging, without impacting the battery life. There is no need to perform any charge/discharge conditioning on this cell type battery. • Do not disassemble the battery. There are no user-serviceable parts in the battery.
Base Charge Mode In order for the battery to be charged, there must be enough voltage for the circuitry to work. There are three conditions during which power can be supplied to the base: Condition 1:9VDC power supply connected to the barrel connector Condition 2:12VDC host power source only Condition 3:5VDC host power source only The chart below describes each selection by condition.
Linking Image Scanner to Base When newly shipped or defaulted to factory settings, the base and image scanner are not linked. Once the image scanner is placed into the base, the software automatically links the image scanner and the base. If the image scanner and base have previously been linked, you do not receive any feedback. If this is the first time that the image scanner and base are linked, both devices emit a short chirp when their radios link.
Single Image Scanner Operation There are two link modes to accommodate different applications: Locked Link Mode and Open Link Mode. Scan the appropriate bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another. Default = Locked Link Mode. Locked Link Mode - Single Image Scanner If you link an image scanner to a base using the Locked Link Mode, other image scanners are blocked from being linked if they are inadvertently placed into the base.
Multiple Image Scanner Operation To put the image scanner in multiple image scanner mode, scan the bar code below. Once you scan this bar code, the image scanner is unlinked from the base and must be placed into the base to re-link. Multiple Image Scanner Operation Note: Multiple Image Scanner Operation Mode allows you to link up to 7 image scanners to one base. You cannot join an eighth image scanner until you unlink one of the 7 image scanners or take an image scanner out of range.
Changing Image Scanner Name - via Bar codes If you wanted to set up your image scanners with names 0001-0007, you may scan the bar codes below. Scan the Reset bar code after each name change and wait for the image scanner to re-link to the base before scanning the next bar code to name the next image scanner. 0001 0002 0003 0004 0005 0006 0007 Reset Alternatively, you may change the name with a bar code command if you cannot send serial commands to the base.
Image Scanner Report Scan the bar code below to generate a report for the connected image scanners. The report indicates the port, work group, image scanner name, and address. Image Scanner Report Application Work Groups Your cordless system can have up to seven image scanners linked to one base. You can also have up to seven work groups. If you want to have all of the image scanners’ settings programmed alike, you don’t need to use more than one work group.
Application Work Group Selection This programming selection allows you to assign an image scanner to a work group by scanning the bar code below. You may then program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires.
Resetting the Standard Product Default Settings: Current Application Work Group If you aren’t sure what programming options are in your image scanner, or you’ve changed some options and want the standard product default settings restored, scan the Standard Product Default Settings: Current Application Group bar code below. The Menu Commands starting on page 10-6 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
Using the Image Scanner with Bluetooth Devices The 3820/3820i image scanner may be used either with the 2020 base or with other Bluetooth devices. Scanning the Non-Base Bluetooth Connection bar code below allows the image scanner to be used with other Bluetooth devices (e.g., PDA, PC - Bluetooth USB Adapter). After you scan the bar code below, follow the instructions supplied with your Bluetooth device to locate the image scanner and connect to it.
and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save. Default = 0 sec (no alarm). Base Alarm Duration Image Scanner Alarm Note: If you are out of range when you scan a bar code, you will receive an error beep even if you do not have the alarm set. You receive the error beep since the data could not be communicated to the base or the host.
Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process. To program a transmit delay between accumulated scans, scan one of the following delays. Note: In most cases, a short (250 ms (milliseconds) delay is ideal; however, longer delays may be programmed. Contact Technical Support (page 15-1) for additional information.
3820/3820i LED Sequences and Their Meaning LED Indication Beeper Indication Cause Normal Operation Red Flash Green Flash None 1 beep Battery low Successful communication or linking Failed communication Red, blinking Menu Operation Green Flash 3 beeps 2 beeps Red, blinking 3 beeps Successful menu change Unsuccessful menu change 2020 LED Sequences and Their Meaning The base contains a red LED that indicates the status of the unit and verifies its communication with the host system and a green LED t
The tables below list the indication and cause of the LED illumination and beeps for the 2020. System Condition System Status Indicator (Red LED) Power On/System Idle LED is on Power On/Diagnostic Error Blink LED for long duration, pulsing indefinitely Receiving Data (2020 only) Blink LED for short duration in multiple pulses. Occurs while transferring data to/from the RF module or the Host port. Base requests status from its own Bluetooth radio Blink LED once (occurs approx.
RF (Radio Frequency) Module Operation The cordless system uses a state-of-the-art two-way Bluetooth radio to transmit and receive data between the image scanner and the base.
Out of Range and Back into Range with Data Accumulation Mode On The image scanner may store a number of symbols (approximately 500 UPC symbols, others may vary) when out of range and then send them to the base when back in range. You will not hear a communication error beep in this mode, but you will hear a short buzz when you pull the trigger if the radio communication is not working.
2. Disconnect the keyboard cable from the back of the terminal/computer. 3. Connect the appropriate interface cable to the base and to the terminal/ computer and keyboard. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface. 4. Turn the terminal/computer power back on. 5. Program the base for the keyboard wedge interface. See "Keyboard Wedge Connection" on page 1-21.) 6.
Reading Techniques The image scanner has a view finder that projects a bright red aiming beam that corresponds to its horizontal field of view. The aiming line should be centered horizontally over the bar code; it will not read if the aiming line is in any other direction. Good Read Bad Read Bad Read The best focus point for reading most code densities is about 5 inches (12.7 cm) from the unit.
Plug and Play Plug and Play bar codes provide instant image scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge Connection If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below. Keyboard wedge is the default interface. Note: The following bar code also programs a carriage return (CR) suffix.
Wand Emulation Plug & Play In Wand Emulation mode, the image scanner decodes the bar code then sends data in the same format as a wand scanner. The Code 39 Format converts all symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code 128 and Interleaved 2 of 5 without any changes, but converts all other symbologies to Code 39. The Wand Emulation Plug & Play Code 39 Format bar code below sets the terminal ID to 61.
Each bar code above also programs the following suffixes for each symbology: Symbology EAN 8 EAN 13 UPC A UPC E Code 39 Interleaved 2 of 5 Code 128 * Code 128 ** Suffix 0C 16 0D 0A 00 0A 00 0D 00 0A 00 18 0B 0B 0B 0B * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR1, and IBM 4683 Port 17 Interfaces **Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface Connecting the Base with USB A base can be connected to the USB port of a computer. 1.
For additional USB programming and technical information, refer to Honeywell “USB Application Note,” available at www.honeywellaidc.com Note: Without using the 9-volt external, power supply, the base only uses enough power from the host to operate the interface. The image scanner’s battery is not charged when in this mode. Using the 9-volt, external power supply allows the image scanner’s battery to be charged, and no power is drawn from the host.
USB Keyboard (PC) USB Keyboard (Mac) USB Japanese Keyboard (PC) USB HID Scan the following code to program the 3820/3820i for USB HID bar code scanners. Scanning this code changes the terminal ID to 131. USB HID bar code Image Scanner USB Com Port Emulation Scan the following code to program the 3820/3820i to emulate a regular RS232-based Com Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com).
ACK/NAK Mode ACK/NAK On * ACK/NAK Off Connecting the Base with Serial Wedge The 2020 uses TTL signal levels to wedge into an RS-232 serial network. Use only 2020 serial wedge cables to prevent damage to the base. Refer to Connecting the Base with RS-232 Serial Port on page 2-8 to set the baud rate and communications protocol. 1. Turn off power to the computer. 2. Disconnect the existing serial cable from the computer. 3. Connect the appropriate interface cable to the base.
5. Plug the other serial connector into the other device connection and tighten the two screws. 6. Plug the power supply barrel connector to the base, and plug the power supply into the AC source. 7. Once the base has been fully connected, power up the computer. To set up the serial wedge terminal ID, use the serial terminal ID 050 and follow the instructions on page 2-1. Make sure that all of the communication parameters match on all of the connected devices. Choosing Both sends scanned data to P1 and P2.
1 - 28
2 Terminal Interfaces Terminal ID If your interface is not a standard PC AT, refer to "Supported Terminals" on page 2-2 through page 2-3, and locate the Terminal ID number for your PC. Scan the Terminal ID bar code below, then scan the numeric bar code(s) from the Programming Chart inside the back cover of this manual to program the image scanner for your terminal ID. Scan Save to save your selection. For example, an IBM AT terminal has a Terminal ID of 003.
Supported Terminals Terminal DEC DEC Esprit Heath Zenith HP IBM IBM IBM IBM 102 key IBM 122 key IBM 122 key IBM 122 key IBM 122 key IBM DOS/V 106 key IBM SurePOS IBM SurePOS IBM Thinkpad IBM Thinkpad IBM Thinkpad I/O 122 key ITT Lee Data NEC Olivetti Olivetti RS-232 TTL Serial Wedge Silicon Graphics Telex 88 key Telex 88 key Telex 102 key 2-2 Model(s) VT510, 520, 525 (PC style) VT510, 520, 525 (DEC style LK411) 200, 400 PC, AT Vectra XT PS/2 25, 30, 77DX2 AT, PS/2 30–286, 50, 55SX, 60, 70, 70–061, 70–121,
Supported Terminals Terminal Telex 122 key USB PC Keyboard USB Mac Keyboard USB Com Port USB HIDPOS Wand Emulation (Code 39 Format) Wand Emulation (Same Code Format) Model(s) 078, 078A, 79, 80, 191, 196, 1191,1192, 1471, 1472, 1476, 1477, 1482, 1483 Terminal ID 046 124** 125** 130 131** 061 064 * Default for 2020-5BE. **It is best to use the Plug and Play bar codes, beginning on page 1-24 to program these interfaces, rather than scanning the terminal ID listed in this table.
Keyboard Country Scan the appropriate country code below to program the keyboard for your country.
Keyboard Country (continued) Italy Latin America Netherlands (Dutch) Norway Poland Portugal Romania Russia SCS Slovakia Spain Sweden Switzerland (German) Turkey F Turkey Q U.K.
Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. Default = Regular. Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock Automatic Caps Lock is used if you change the Caps Lock key on and off.
Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + ASCII Mode On: The image scanner sends key combinations for ASCII control characters for values 00-1F. Refer to Keyboard Function Relationships, page 7-1 for CTRL+ ASCII Values. Default = Off Control + ASCII Mode On * Control + ASCII Mode Off Turbo Mode: The image scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.
Connecting the Base with RS-232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the base. Note: For the base to work properly, you must have the correct cable for your type of terminal/computer. 3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port. 4. Plug the power supply barrel connector to the base, and plug the power supply into the AC source. 5.
RS-232 Baud Rate Baud Rate sends the data from the image scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the image scanner. Default = 115,200. 300 600 1200 2400 4800 9600 19200 38400 57,600 * 115,200 RS-232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.
Parity provides a means of checking character bit patterns for validity. Default = None. 7 Data, 1 Stop, Parity Even 7 Data, 1 Stop, Parity None 7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd RS-232 Handshaking RS-232 Handshaking allows control of data transmission from the image scanner using software commands from the host device. CTS/RTS operates in mode 2.
transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off when XOFF was sent. Default = RTS/CTS, XON/ XOFF and ACK/NAK Off. RTS/CTS On * RTS/CTS Off XON/XOFF On * XON/OFF Off ACK/NAK On * ACK/NAK Off Host ACK Selection Some applications require that the host terminal (or server) approve or reject incoming bar code data and notify the operator of these actions.
Commands may be strung together to create custom response sequences. An example of a command string is listed below. 0456, The above example will make an image scanner in application work group zero beep low, medium, high. Once Host ACK is enabled, the system works as follows: • The image scanner reads a code and sends data to the base/host system. No audible or visual indication is emitted until you receive an escape command.
2020 Host Escape Commands Command Action a Indicate as if successful menu change made b Indicate as if unsuccessful menu change made 1 Illuminate green LED for 135 milliseconds (followed by at least 70 mSecs. dark time when multiple blinks) 2 Illuminate green LED for two seconds (followed by at least 500 mSecs. dark time when multiple blinks) 3 Illuminate green LED for five seconds (followed by at least 500 mSecs.
Wand Emulation Wand Emulation Connection The Wand Emulation Connection bar codes should be used if you want to change the terminal ID only, without changing any other image scanner settings. We recommend using Wand Emulation Plug & Play bar codes to program your image scanner to emulate a wand reader. The Wand Emulation Plug & Play bar codes change other parameters, in addition to changing the terminal ID. Please refer to Wand Emulation Plug & Play on page 1-22 for further information.
Wand Emulation Transmission Rate The transmission rate is limited by the terminal’s ability to receive data without dropping characters. Default = 25 inches/second. 10 * 25 40 80 120 150 200 Wand Emulation Polarity The Polarity can be sent as standard with black bars high, or reversed with white bars high. Default = Black High. * Black High White High Wand Emulation Idle The idle describes the state of the image scanner when no data is being transmitted.
Wand Emulation Data Block Size This transmits the data in smaller blocks to prevent buffer overflow. Default = 40. 20 * 40 60 80 Wand Emulation Delay Between Blocks This sets the delay time between data blocks. Default = 50ms. 5ms * 50ms 150ms 500ms Wand Emulation Overall Checksum When this option is turned on, a computed check character is added at the end of the entire message.
3 Output Image Scanner Functions Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = On. * Beeper - Good Read On Beeper - Good Read Off Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the image scanner emits on a good read. Default = Medium.
Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the image scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (3250 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the image scanner emits on a good read. Default = Normal. * Normal Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Good Read Delay This sets the minimum amount of time before the image scanner can read another bar code. Default = 0 ms (No Delay.) * No Delay Short Delay (500 ms) Medium Delay (1000 ms) Long Delay (1500 ms) User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
Read Time-Out (Serial Trigger Mode) Use this selection to set a time-out (in milliseconds) of the image scanner’s trigger when using serial commands to trigger the image scanner. Once the image scanner has timed out, you can activate the image scanner either by pressing the trigger or using a serial trigger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save.
If there are no trigger pulls during the “image scanner power time-out timer” interval, the image scanner goes into power down mode. Whenever the trigger is enabled, the “image scanner power time-out timer” is reset. If the image scanner is placed in the 2020 cradle and the battery is in the process of being charged, the image scanner will not go into power down mode.
Hands Free Time-Out The Automatic Trigger and Presentation Modes are referred to as “hands free” modes. If the image scanner’s trigger is pulled when using a hands free mode, the image scanner changes to manual trigger mode. You can set the time the image scanner should remain in manual trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls) the image scanner reverts to the original hands free mode.
Centering Window Use the centering feature to narrow the image scanner’s field of view so the image scanner reads only the bar code you want. When centering is turned on, the image scanner only reads codes that intersect or are contained within the centering window you set up. At least part of a bar code must be within the window to be decoded or output by the image scanner. To change the left or right edge of the centering window, scan Centering On, then scan one of the following bar codes.
Example: If you have two bar codes next to one another and the centering window is set to 40% left edge and 60% right edge, only the bar code that intersects that window will be decoded. Decoded bar code 40% 30% 20% 60% 70% 80% 90% 10% 0% 100% Preferred Symbology The 3820/3820i can be programmed to specify one symbology as a higher priority over other symbologies in situations where both bar code symbologies appear on the same label, but the lower priority symbology cannot be disabled.
High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology bar code below. On the Symbology Chart on page A-1, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart (inside back cover). Scan Save to save your selection. Default = None High Priority Symbology Low Priority Symbology To specify the low priority symbology, scan the Low Priority Symbology bar code below.
Output Sequence Overview Require Output Sequence When turned off, the bar code data will be output to the host as the image scanner decodes it. When turned on, all output data must conform to an edited sequence or the image scanner will not transmit the output data to the host device. Note: This selection is unavailable when the Multiple Symbols Selection is turned on.
5. End Output Sequence Editor Scan F F to enter an Output Sequence for an additional symbology, or Save to save your entries. Other Programming Selections •Discard This exits without saving any Output Sequence changes. Output Sequence Editor Enter Sequence Default Sequence Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the image scanner will not transmit the output data to the host device.
Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the image scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example.
To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or formatted characters as part of the length.
No Read With No Read turned On, the image scanner sends an “NR” to the host if you pull and release the trigger without reading a code (e.g., bad bar code). If No Read is turned Off, the “NR” will not be sent to the host. No Read On * No Read Off If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message using the Data Formatter (page 5-4). The hex code for the No Read symbol is 9C.
4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string. Prefix and Suffix characters are data characters that can be sent before and after scanned data.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252) on page A-4, for the prefix or suffix you wish to enter. Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 6. Repeat Steps 4 and 5 for every prefix or suffix character. Step 7. To add the Code I.D., scan 5, C, 8, 0. To add AIM I.D., scan 5, C, 8, 1. To add a backslash (\), scan 5, C, 5, C.
Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Your change is automatically saved. To Add a Carriage Return Suffix to All Symbologies Scan the following bar code if you wish to add a carriage return suffix to all symbologies at once. This action first clears all current suffixes, then programs a carriage return suffix for all symbologies.
Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the image scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 7-3. When the image scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.
Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual. Prefix Scanned Data 1 2 3 4 Suffix 5 Intercharacter Delay Intercharacter Delay To remove this delay, scan the Intercharacter Delay bar code, then set the number of steps to 0.
Interfunction Delay An interfunction delay of up to 495 milliseconds may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual. Prefix STX 1 Scanned Data HT 2 3 4 5 Suffix CR LF Interfunction Delays Interfunction Delay To remove this delay, scan the Interfunction Delay bar code, then set the number of steps to 0.
5 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the image scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None.
Step 4. Code I.D. In the Appendix A, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 5. Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050.
ASCII Conversion Chart (Code Page 1252) on page A-4, and nn is the numeric value (00-99) for the number of times it should be sent.) E9 Send all but the last “nn” characters, starting from the current cursor position. Syntax = E9nn (nn is the numeric value (00-99) for the number of characters that will not be sent at the end of the message.) Move Commands F5 Move the cursor ahead “nn” characters from current cursor position.
E5 FE EC ED ters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. Terminates character replacement. Syntax = E5. Compare character in current cursor position to the character “xx.” If characters are equal, increment cursor. If characters are not equal, no format match. Syntax = FExx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-4.) Check to make sure there is an ASCII number at the current cursor position.
When Data Formatter is required, all input data must conform to an edited format or the image scanner does not transmit the input data to the host device. Data Format On, Format Required Alternate Data Formats Alternate formats allow you “single shot” capability to scan one bar code using a different data format than your primary format. When data formats are programmed (see page 5-1), you must input whether you are programming the primary format, or an alternate format numbered 1, 2, or 3.
5-6
6 Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults.
Message Length You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code doesn’t match the valid reading length, the image scanner will issue an error beep. You may wish to set the same value for minimum and maximum length to force the image scanner to read fixed length bar code data. This helps reduce the chances of a misread. EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09 Max.
Codabar Codabar * On Off Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the image scanner to read only Codabar bar codes with Modulo 16 check characters. Default = No Check Character.
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the image scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character.
Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length Code 39 < Default All Code 39 Settings > Code 39 * On Off Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters.
Code 39, continued Code 39 Check Character No Check Character indicates that the image scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check character, but will not transmit the check character with the scanned data.
Code 39, continued Code 39 Append This function allows the image scanner to append the data from several Code 39 bar codes together before transmitting them to the host computer. When this function is enabled, the image scanner stores those Code 39 bar codes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data. The image scanner stores the data in the order in which the bar codes are read, deleting the first space from each.
Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = On.
Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
When Check Digit is set to Validate and Transmit, the image scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit Interleaved 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80.
Code 93 < Default All Code 93 Settings > Code 93 * On Off Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 Code Page Code pages define the mapping of character codes to characters.
Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On * Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Straight 2 of 5 IATA, continued On * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 11 Code 11 On * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.
Code 11, continued Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Code 128, continued ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license.
Code 128 Function Code Transmit By default, Code 128 function codes are not transmitted with Code 128 bar code data. However, if you wish to transmit Code 128 function codes with the bar code data, scan the Function Codes On bar code, below. * Function Codes Off Function Codes On Telepen Telepen On * Off Telepen Output Using AIM Telepen Output, the image scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1).
Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length UPC A UPC A * On Off UPC A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
UPC A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data. Default = Off for both 2 Digit and 5 Digit Addenda.
UPC A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. Default = On.
UPC E0 and UPC E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number system, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1). * UPC E0 On UPC E0 Off UPC E1 On * UPC E1 Off UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off.
UPC E0 and UPC E1 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off UPC E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC E0 Number System The numeric system digit of a U.P.C.
UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 EAN/JAN 13 * On Off EAN/JAN 13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
EAN/JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 Addenda Required When Addenda Required is set to on, the image scanner will only read EAN/ JAN 13 bar codes that have addenda. Default = Not Required.
ISBN Translate This selection causes EAN-13 Bookland symbols to be translated into their equivalent ISBN number format. Default = Off. On * Off EAN/JAN 8 EAN/JAN 8 * On Off EAN/JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
EAN/JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 8 Addenda Required When Addenda Required is set to on, the image scanner will only read EAN/ JAN 8 bar codes that have addenda. Default = Not Required.
MSI MSI On * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the image scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate and Transmit, the image scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data.
Plessey Code Plessey Code On * Off Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
GS1 DataBar Omnidirectional * On Off GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited * On Off GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > 6 - 29
GS1 DataBar Expanded * On Off GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. Minimum Message Length Maximum Message Length GS1 Emulation The imager can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol.
China Post Code China Post Code On * Off China Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Korea Post Code Korea Post Code On * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
You have to have PosiCode A and B on to read any of the PosiCode symbologies. A and B On (No Limited) A and B and Limited A On (Limited B Off) * A and B and Limited B On (Limited A Off) PosiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Codablock F Codablock F On * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Code 16K On * Off Code 16K Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-160. Minimum Default = 1, Maximum Default = 160.
Code 49 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81.
7 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the image scanner. Refer to page 2-7 enable Control + ASCII mode.
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Country Codes United States [ \ ] 6 - Belgium [ < ] 6 - Scandinavia 8 < 9 6 - France ^ 8 $ 6 = Germany à + 6 - Italy \ + 6 - Switzerland < ..
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM AT/XT and PS/2 Compatibles, WYSE PC/AT Supported Keys Reserved Enter (KP) Cap Lock ALT make ALT break CTRL make CTRL break CR/Enter Reserved Tab Reserved Tab Delete CR/Enter Insert Escape F11 Home Print Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM, Memorex Telex (102)* Supported Keys Reserved Enter F11 F12 F13 F14 F15 New Line F16 F17 F18 Tab/Field Forward Delete Field Exit Insert Clear Error Reset Home Print Back Space Back Tab F19 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Memorex Telex (88)** Supported Keys Res
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F Esprit 200, 400 ANSI Supported Keys Reserved New Line N/A N/A N/A N/A N/A New Line N/A Tab N/A Tab N/A New Line N/A Escape F11 Insert F13 Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Esprit 200, 400 ASCII Supported Keys Reserved New Line N/A N/A N/A N/
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US DEL 7-6 HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 7F Apple Mac/iMac Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make TAB APPLE break TAB Del RETURN Ins Help ESC F11 Home Prnt Scrn BACKSPACE LSHIFT TAB F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 BACKSPACE
8 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is reset.
Image Scanner Report Scan the bar code below to generate a report for the connected image scanners. The report indicates the port, work group, image scanner name, and address. To assign a name to your image scanner, refer to "Menu Command Syntax" on page 10-1. Image Scanner Report Image Scanner Address Scan the bar code below to determine the address of the image scanner you are using. Image Scanner Address Base Address Scan the bar code below to determine the address of the base you are using.
Resetting the Standard Product Default Settings: All Application Work Groups The following bar code defaults all of the work groups to the factory settings. Standard Product Default Settings: All Application Groups The Menu Commands starting on page 10-6 list the standard product default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
8-4
9 Visual Xpress Visual Xpress Introduction Visual Xpress provides a wide range of PC-based programming functions that can be performed on an imager connected to your PC's COM port. Visual Xpress allows you to download upgrades to the imager's firmware, change programmed parameters, and create and print programming bar codes. Using Visual Xpress, you can even save/open the programming parameters for an imager.
Installing Visual Xpress from the Web Note: Visual Xpress requires .NET software. If .NET is not installed on your PC, you will be prompted to install it during the Visual Xpress installation. 1. Access the Honeywell web site at www.honeywellaidc.com. 2. Click on Software Downloads. 3. Select your product from the dropdown list. 4. Click on the entry for Visual Xpress. 5. When prompted, select Save File, and save the files to the c:\windows\temp directory. 6.
10 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the 2020. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an RS-232 interface (see page 1-21). The following commands can be sent via a PC com port using terminal emulation software.
Data The new value for a menu setting, identified by the Tag and SubTag. Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs the command’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s operation on the device’s non-volatile menu configuration table. Use the non-volatile table only for semi-permanent changes you want saved through a power cycle.
Responses The device responds to serial commands with one of three responses: ACKIndicates a good command which has been processed. ENQIndicates an invalid Tag or SubTag command. NAKIndicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters.
Example #4: What are the device’s settings for all Codabar selections? Enter: cbr?. Response: CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK], DFT[ACK].
The Menu Commands starting on page 10-6 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages). Note: Scanning this bar code also causes both the image scanner and the base to perform a reset and become unlinked. Refer to "Linking Image Scanner to Base" on page 1-5 for additional information.
Menu Commands Selection Base Charge Mode Image Scanner Modes - Single Setting Serial Command Page * Indicates default # Indicates a numeric entry *Automatic BASCHG1 1-4 Full Charge Rate BASCHG2 1-4 Low Charge Rate BASCHG3 1-4 Battery Charge Off BASCHG4 1-4 Unlink Image Scanner BT_RMV 1-5 *Locked Link Mode BASCON0,DNG1 1-6 Open Link Mode BASCON1,DNG1 1-6 Override Locked Image Scanner BT_RPL1 1-6 Multiple Image Scanner Operation Multiple Image Scanner Operation BASCON2,DNG3
Selection Out-of-Range Alarm Setting * Indicates default Base Alarm Duration (Range 1 - 3000 sec (*0)) Image Scanner Alarm Duration (Range 1 3000 sec (*0)) Alarm Sound Type Serial Command # Indicates a numeric entry Page 1-13 BASORD BT_ORD 1-13 1-13 Base Alarm Type BASORW Image Scanner Alarm Type BT_ORW Data Accumulation Mode On BATENA1 1-13 *Off BATENA0 1-13 Batch Mode Transmit Delay *Off BATDLY0 1-14 Short (ms) BATDLY250 1-14 Medium (ms) BATDLY500 1-14 Long (ms) BATDLY1000
Selection Program Keyboard Country 10 - 8 Setting Serial Command Page * Indicates default # Indicates a numeric entry *U.S.A.
Selection Keyboard Style Keyboard Modifiers Serial Port Connection Baud Rate Setting Serial Command Page * Indicates default # Indicates a numeric entry *Regular KBDSTY0 2-6 Caps Lock KBDSTY1 2-6 Shift Lock KBDSTY2 2-6 Automatic Caps Lock KBDSTY6 2-6 Emulate External Keyboard KBDSTY5 *Control + ASCII Off KBDCAS0 2-7 Control + ASCII On KBDCAS2 2-7 *Turbo Mode Off KBDTMD0 2-7 Turbo Mode On KBDTMD1 2-7 *Numeric Keypad Off KBDNPS0 2-7 Numeric Keypad On KBDNPS1 2-7 *Auto
Selection Word Length: Data Bits, Stop Bits, and Parity RS-232 Handshaking Setting * Indicates default Serial Command # Indicates a numeric entry Page 2-10 7 Data, 1 Stop, Parity Even 232WRD3 7 Data, 1 Stop, Parity None 232WRD0 7 Data, 1 Stop, Parity Odd 232WRD6 7 Data, 2 Stop, Parity Even 232WRD4 7 Data, 2 Stop, Parity None 232WRD1 7 Data, 2 Stop, Parity Odd 232WRD7 8 Data, 1 Stop, Parity Even 232WRD5 *8 Data, 1 Stop, Parity None 232WRD2 8 Data, 1 Stop, Parity Odd 232WRD8 *RTS/CTS
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Wand Emulation Polarity *Black High WNDPOL0 2-15 White High WNDPOL1 2-15 Wand Emulation Idle Idle Low WNDIDL0 2-15 *Idle High WNDIDL1 2-15 Wand Emulation Data Block Size 20 WNDBLK0 2-16 *40 WNDBLK1 2-16 60 WNDBLK2 2-16 Wand Emulation Delay Between Blocks Wand Emulation Overall Checksum 80 WNDBLK3 2-16 5ms WNDDLY0 2-16 *50ms WNDDLY1 2-16 150ms WNDDLY2 2-16 500ms WNDDLY3 2-16 *O
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Number of Beeps Good Read *1 BEPRPT1 3-2 Range 1 - 9 BEPRPT# 3-2 Good Read Delay *No Delay DLYGRD0 3-3 Short Delay (500 ms) DLYGRD500 3-3 Medium Delay (1000 ms) DLYGRD1000 Long Delay (1500 ms) DLYGRD1500 User-Specified Good Read Delay Range 0 - 30,000 ms Trigger Mode *Manual Trigger TRGMOD0 Read Time-Out (0 300,000 ms) *30,000 TRGSTO#### Image Scanner Power Time-Out Timer (07200 seconds) *360
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Centering On DECWIN1 3-7 *Centering Off DECWIN0 3-7 Left of Centering Window *40 DECLFT### Right of Centering Window *60 DECRGT### On PRFENA1 3-8 *Off PRFENA0 3-8 High Priority Symbology PRFCOD## Low Priority Symbology PRFBLK## Preferred Symbology Timeout (*500) Range 100-3000 PRFPTO#### Preferred Symbology Default PRFDFT Output Sequence Editor Enter Sequence SEQBLK 3-11 Default Sequence
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Add Suffix SUFBK2## 4-4 Clear One Suffix SUFCL2 4-4 Clear All Suffixes SUFCA2 4-4 *Enable RMVFNC0 4-4 Disable RMVFNC1 4-4 DLYCHR## 4-5 Delay Length DLYCRX## 4-5 Character to Trigger Delay DLY_XX### 4-5 Interfunction Delay DLYFNC## 4-6 Intermessage Delay DLYMSG## 4-6 DFMDF3 5-4 Enter Data Format DFMBK3## 5-4 Clear One Data Format DFMCL3 5-4 Clear All Data Formats DFMCA3 5-4 Off
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Codabar Start/Stop Char. *Don’t Transmit CBRSSX0 6-3 Transmit CBRSSX1 6-3 Codabar Check Char. *No Check Char.
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Interleaved 2 of 5 Off I25ENA0 6-9 *On I25ENA1 6-9 Interleaved 2 of 5 Check Digit *No Check Char.
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Matrix 2 of 5 Message Length Minimum (1 - 80) *4 X25MIN## 6-14 Maximum (1 - 80) *80 X25MAX## 6-14 Code 11 Default All Code 11 Settings C11DFT 6-14 Code 11 *Off C11ENA0 6-14 On C11ENA1 6-14 Code 11 Check Digits Required 1 Check Digit C11CK20 6-14 *2 Check Digits C11CK21 6-14 Code 11 Message Length Minimum (1 - 80) *4 C11MIN## 6-15 Maximum (1 - 80) *80 C11MAX## 6-15 Code 128 Default All
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry UPC A Default All UPC A Settings UPADFT 6-18 UPC A Off UPAENA0 6-18 *On UPAENA1 6-18 UPC A Check Digit Off UPACKX0 6-18 *On UPACKX1 6-18 UPC A Number System Off UPANSX0 6-19 *On UPANSX1 6-19 UPC A 2 Digit Addenda *Off UPAAD20 6-19 On UPAAD21 6-19 UPC A 5 Digit Addenda *Off UPAAD50 6-19 On UPAAD51 6-19 UPC A Addenda Required *Not Required UPAARQ0 6-19 Required UPAARQ1 6-19
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry UPC E 5 Digit Addenda *Off UPEAD50 6-23 On UPEAD51 6-23 UPC E Addenda Required *Not Required UPEARQ0 6-21 Required UPEARQ1 6-21 UPC E Addenda Separator Off UPEADS0 6-22 *On UPEADS1 6-22 EAN/JAN 13 Default All EAN/ JAN 13 Settings E13DFT 6-23 EAN/JAN 13 Off E13ENA0 6-23 *On E13ENA1 6-23 EAN/JAN 13 Check Digit Off E13CKX0 6-23 *On E13CKX1 6-23 EAN/JAN 13 2 Digit Addenda *Off E13
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry EAN/JAN 8 5 Digit Addenda *Off EA8AD50 6-26 On EA8AD51 6-26 EAN/JAN 8 Addenda Required *Not Required EA8ARQ0 6-26 Required EA8ARQ1 6-26 EAN/JAN 8 Addenda Separator Off EA8ADS0 6-26 *On EA8ADS1 6-26 Coupon Code Off CPNENA0 6-26 *On CPNENA1 6-20 MSI Default All MSI Settings MSIDFT 6-27 MSI *Off MSIENA0 6-27 On MSIENA1 6-27 *Validate Type 10, but Don’t Transmit MSICHK0 6-27 Vali
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry GS1 DataBar Expanded Default All GS1 DataBar Expanded Settings RSEDFT 6-30 GS1 DataBar Expanded Off RSEENA0 6-30 *On RSEENA1 6-30 GS1 DataBar Expanded Msg.
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Off POSENA0 6-32 *On POSENA1 6-32 A and B On POSLIM0 6-33 A and B and Limited A On POSLIM1 6-33 *A and B and Limited B On POSLIM2 6-33 PosiCode Msg. Length Minimum (2 - 80) *4 POSMIN## 6-33 Maximum (2 - 80) *48 POSMAX## 6-33 Codablock F Default All Codablock F Settings CBFDFT 6-34 Codablock F *Off CBFENA0 6-34 PosiCode On CBFENA1 6-34 Codablock F Msg.
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Maximum Link Attempts *0 (0 - 100) BT_MLA### B-2 Relink Time-Out *3 (1 - 100) BT_RLT### B-2 10 - 23
10 - 24
11 Product Specifications 3820 Product Specifications Parameter Specification Dimensions (Typical): Height 6.2 inches (15.7 cm) Length 5.3 inches (13.5 cm) Width 3.2 inches (8.1 cm) Weight (with battery) 9.2 ounces (260 g) Light Source 630 nM visible red LED Scan Rate 270 scans per second in most usages Skew Angle ±65 degrees Pitch Angle ±65 degrees Horizontal Velocity 2 inches (5 cm) per second Scan Contrast 20% minimum Battery: Lithium Ion Battery Capacity: Storage: 3.
3820i Product Specifications Parameter Specification Dimensions (Typical): Height 6.5 inches (16.5 cm) Length 5.3 inches (13.5 cm) Width 3.2 inches (8.1 cm) Weight (with battery) 9.6 ounces (272 g) Light Source 630 nM visible red LED Scan Rate 270 scans per second in most usages Skew Angle ±65 degrees Pitch Angle ±65 degrees Horizontal Velocity 2 inches (5 cm) per second Scan Contrast 20% minimum Battery: Lithium Ion Battery Capacity: Storage: 3.
2020-5BE Product Specifications Parameter Specification Dimensions (Typical): Height 3.1 inches (7.9 cm) Length 5.6 inches (14.2 cm) Width 4.3 inches (10.9 cm) Weight 8.8 ounces (250 g) Voltage: DC Barrel 8.5 to 9.5 volts Host Port 4.
2020-CBE Product Specifications Parameter Specification Dimensions (Typical): Height 3.1 inches (7.9 cm) Length 5.6 inches (14.2 cm) Width 4.3 inches (10.9 cm) Weight 8.8 ounces (250 g) Voltage: DC Barrel Current Draw: 9 Volt DC Barrel 8.5 to 9.
10 2 3 4 5 6 7 8 9 1 connects to the base Cord shield Tied to supply power Supply ground Terminal clock Terminal data Supply power input (Refer to tables on page 11-3.
Standard Cable Pinouts Wand Emulation 10 Pin Modular Plug connects to the base connects to your terminal 9 Pin Type D Female 1 9 8 Cord shield 7 Supply ground 6 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 6 Bar code data output 7 Supply power input (Refer to tables on page 11-3.
2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 Receive data - Serial data to image scanner 6 Transmit data - Serial data from image scanner 7 Supply power input (Refer to tables on page 11-3.
Standard Cable Pinouts USB 10 Pin Modular Plug connects to the base 1 2 Data + 3 Tied to supply power 4 Supply ground 5 6 7 5 volt supply power input 8 9 10 Data - 11 - 8
12 Maintenance Maintenance Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center. See "Customer Support" on page 13-1 for further information. Cleaning the Device Reading performance may degrade if the image scanner’s window is not clean. If the window is visibly dirty, or if the image scanner isn’t operating well, clean the window with a soft cloth or lens tissue dampened with water (or a mild soapy water solution).
Replacing the 2020 Interface Cable: 1. Turn the power to the host system OFF. 2. Disconnect the base’s cable from the terminal or computer. 3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release clip. 5. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Changing the 3820/3820i Battery: 1. Remove the screw on the end cap on the 3820.
• The power cable is connected properly and there is power at the power source. • The host system power is on (if external power isn’t used). Is the green LED on? If the green LED isn’t illuminated, check that: • • • • The image scanner is correctly placed in the base. There is external power or 12 volt host power. Charge mode is turned on. (See "Base Charge Mode" on page 1-4) The battery is not bad or deeply discharged.
The image scanner won’t read your bar code at all. 1. Scan the sample bar codes in the back of this manual. If the image scanner reads the sample bar codes, check that your bar code is readable. Verify that your bar code symbology is enabled (see Chapter 6). 2. If the image scanner still can’t read the sample bar codes, scan All Symbologies on page 6-1.
13 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please contact us by using one of the methods below: Knowledge Base: www.hsmknowledgebase.com Our Knowledge Base provides thousands of immediate solutions. If the Knowledge Base cannot help, our Technical Support Portal (see below) provides an easy way to report your problem or ask your question. Technical Support Portal: www.hsmsupportportal.
Mexico Telephone: 01-800-HONEYWELL (01-800-466-3993) Fax: +52 (55) 5531-3672 E-mail: mxservice@honeywell.com Europe, Middle East, and Africa Telephone: +31 (0) 40 2901 633 Fax: +31 (0) 40 2901 631 E-mail: euroservice@honeywell.com Hong Kong Telephone: +852-29536436 Fax: +852-2511-3557 E-mail: apservice@honeywell.com Singapore Telephone: +65-6842-7155 Fax: +65-6842-7166 E-mail: apservice@honeywell.com China Telephone: +86 800 828 2803 Fax: +86-512-6762-2560 E-mail: apservice@honeywell.
product by anyone other than Honeywell or its authorized representatives. This warranty shall extend from the time of shipment for the duration published by Honeywell for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to Honeywell’s factory or authorized service center for inspection.
13 - 4
A Reference Charts Symbology Chart Symbology AIM ID Possible AIM ID Modifiers ( m) All Symbologies Code ID (hex) (0x99) China Post ]X0 Codabar ]Fm 0-1 Q (0x51) a (0x61) Codablock F ]Om 0, 1, 4, 5, 6 q (0x71) Code 11 ]H3 Code 128 ]Cm 0, 1, 2, 4 j (0x6A) Code 16K ]Km 0, 1, 2, 4 o (0x6F) Code 32 Pharmaceutical (PARAF) ]X0 Code 39 (supports Full ASCII mode) ]Am 0, 1, 3, 4, 5, 7 b (0x62) Code 49 ]Tm 0, 1, 2, 4 l (0x6C) Code 93 and 93i ]Gm 0-9, A-Z, a-m i (0x69) EAN-13 (inc
Symbology UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E AIM ID Possible AIM ID Modifiers ( m) Code ID (hex) ]E0 c (0x63) ]E3 c (0x63) ]E3 c (0x63) ]E0 E (0x45) UPC-E with Add-On ]E3 E (0x45) UPC-E1 (obsolete) ]X0 E (0x45) Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details.
ASCII Conversion Chart (Code Page 1252) Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
Printable Characters (Continued) DEC HEX 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F Character ( ) * + , .
Extended ASCII Characters (Continued) DEC HEX 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA Character Œ Ž ‘ ’ “ ” • – — ˜ ™ š › œ ž Ÿ ¡ ¢ £ ¤ ¥ ¦ § ¨ © ª DEC HEX 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6
one the host program is expecting. If this is the case, select the code page with which the bar codes were created. The data characters should then appear properly. Note: The Code Page option is available for Code 39, Code 93, and Code 128.
B Minimizing Bluetooth/ISM Band Network Activity The settings described below can help you customize the re-linking behavior of the cordless linear imaging system to obtain the best compromise between convenience and low interference. Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth.
Event Auto Reconnect On Auto Reconnect Off Image scanner reset due to firmware upgrade Re-link occurs automatically. Image scanner reset due to battery change Re-link occurs automatically. Image scanner placed in different base unit Re-link to new base occurs automatically. Maximum Link Attempts The Maximum Link Attempts setting controls the number of times the image scanner tries to form a connection with a base unit or PC.
Scan the Relink Time-Out bar code, then scan the number of seconds for the setting (from 1-100) from the inside back cover. Scan Save to save the setting. Default = 3 seconds. Relink Time-Out Bluetooth/ISM Network Activity Examples Default values: When the image scanner goes out of range, the image scanner repeatedly attempts to connect to base unit. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time.
Auto Reconnect Mode set to 1 Maximum Link Attempts set to 0 Relink Time-Out set to 10 Image Scanner Power Time-Out Timer set to 1800: Note: See Image Scanner Power Time-Out Timer on page 3-4. The image scanner attempts to connect to the base unit every 15 seconds, measured from start of attempt to start of attempt. After one half hour, the image scanner powers off.
Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN 13 EAN 8 9 780330 290951 654 3210 5 UPC-E 0 456123 8
Sample Symbols Code 39 BC321 Code 93 123456-9$ Matrix 2 of 5 6543210 Codabar A13579B Straight 2 of 5 Industrial 123456 GS1 DataBar (01)00123456789012
Programming Chart 0 1 2 3 4 5 6 7 8 9 A B C D E F Discard Save Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.
