Install Instructions

ManualsBrandsHoneywell Home ManualsDampers6" Round Automatic TrueZONE Damper

INSTALLATION INSTRUCTIONS

33-00040-03

TrueZONE ARD, EARD, and ZD

Series Dampers

APPLICATION

ARD Series Damper

The ARD is a round damper with a 24 Vac, spring-Open

return damper motor used to control circulating air in

heating, cooling, and ventilating systems.

EARD Series Damper

The EARD is a round damper with a 24 Vac powered-

open/spring-closed motor. It is used for fresh air intake for

Ventilation or for combustion makeup air.

ZD Series Damper

The ZD is a power close and spring open damper. It has a

24-volt motor used to control circulating air in HVAC

systems and used when a normally-open damper is

required. The ZD is typically used with the TrueZONE and

other electronic zoning systems.

FEATURES

• Taping Flange and non-interfering set screw

• High Temperature outer plastic for hot environments

• Redesigned all Metal Drive Train Gears

• Front facing display with LED Indication light for

Open and Close.

• Adjustable damper position range stops

• Quiet operation.

ARD Features

• Adjustable close position range stops

• Shipped as power closed/spring return open damper.

• Available in 5 to 10” inch, 12, 14, 16, 18, and 20 inch

diameter sizes.

• Male (crimped) and female (uncrimped) ends to

connect to any rigid or flexible round duct.

• Rated to operate up to 1 in. wc

• Blade closes off tightly against gasket for minimal

leakage.

• Fail-safe, normally open operation

• Simple, easy-to-wire, two-wire installation with a third

wire option M4 for LED open only light

EARD Features

• Adjustable open position range stops

• Shipped as power open/spring return closed damper.

• Blade closes off tightly against gasket for minimal

leakage.

• Galvanized steel

• Rated to operate up to 1 in. wc

• Simple, easy-to-wire, two-wire installation

• Male (crimped) and female (uncrimped) ends to

connect to any rigid or flexible round duct.

ZD Features

• Adjustable closed position range stops

• Rated to operate up to 1 in. wc

• Solid construction using extruded aluminum frame and

blades

• Parallel blade design for low leakage performance

• Simple, easy-to-wire, two-wire installation with a third

wire option M4 for LED open light

• Fail-safe, normally open operation

• Ordering Instructions: Order ZD (dimension 1) x

(dimension 2). (Motor is always mounted on dimension

2 side.) For example, ZD10x8TZ is a 10 in. x 8 in. damper

with the motor on the 8 in. side; but a ZD8x10TZ is a 8

in. x 10 in. damper that has the motor on the 10 in. side.

• Damper can be installed in any orientation (mounting

side can be on either the bottom or the side of the duct).

Summary of content (8 pages)

PAGE 1
TrueZONE ARD, EARD, and ZD Series Dampers INSTALLATION INSTRUCTIONS APPLICATION ARD Features The EARD is a round damper with a 24 Vac poweredopen/spring-closed motor. It is used for fresh air intake for Ventilation or for combustion makeup air. • Adjustable close position range stops • Shipped as power closed/spring return open damper. • Available in 5 to 10” inch, 12, 14, 16, 18, and 20 inch diameter sizes. • Male (crimped) and female (uncrimped) ends to connect to any rigid or flexible round duct.
PAGE 2
TRUEZONE ARD, EARD, AND ZD SERIES DAMPERS SPECIFICATIONS Maximum Static Pressure: 1 in. wc for all models except 0.3 in. wc for ARD20. IMPORTANT The specifications given in this publication do not include normal manufacturing tolerances. Therefore, this unit may not exactly match the listed specifications. Also, this product is tested and calibrated under closely controlled conditions, and some minor differences in performance can be expected if those conditions are changed.
PAGE 3
TRUEZONE ARD, EARD, AND ZD SERIES DAMPERS Installing the Round (ARD and EARD) Dampers 1. 2. 3. Planning the Installation Insert the crimped end of the ARD or EARD into the uncrimped end of the rigid round duct and secure with sheet metal screws (not provided). When using flexible duct, slip the duct over the end of the ARD or EARD and secure it with duct straps (not provided).
PAGE 4
TRUEZONE ARD, EARD, AND ZD SERIES DAMPERS WIRING Wiring a Motor See Fig. 6 for motor wiring hookups for ARD and ZD Dampers. CAUTION Personal Electrical Shock Hazard. Can cause electrical shock or equipment damage. Disconnect power before beginning installation. The damper motor has a 24 Vac, 50/60 cycle, 8 VA rating. The spring-return ARD and ZD damper requires 24 Vac to M1 and M6 to power the damper closed. The damper then returns to its normal open position once power is removed.
PAGE 5
TRUEZONE ARD, EARD, AND ZD SERIES DAMPERS Wiring TH8321WF or TH8321R without EIM S1 C S1 K EARD R W RC 1 C Y R G U1 W HVAC Y G W2 U1 Y2 A TH8321WF OR TH8321R THERMOSTAT 1 JUMPERS NEEDED M37607 Fig. 4. TH8321WF or TH8321R without EIM controlling EARD damper.
PAGE 6
TRUEZONE ARD, EARD, AND ZD SERIES DAMPERS Wiring TH8321R or Prestige with EIM TO THERMOSTAT R C CONV POWER W HEAT W2 COOL W3 FAN W Y G Y U1 Y2 U2 G U3 HVAC R C A U3 U3 U2 U2 U1 EARD U1 *1 A RH B RC C R D C S4 S2 S4 S2 S3 SENSORS S3 S1 S1 THM5421 R1021 EIM 1 JUMPERS NEEDED M37606 Fig. 5. TH8321R or Prestige with EIM controlling EARD damper.
PAGE 7
TRUEZONE ARD, EARD, AND ZD SERIES DAMPERS CHECKOUT Wiring ARD or ZD Damper To check out the ARD or ZD: 1. With 24 Vac applied to M1 and M6, observe the motor powering the damper to the closed position. 2. With power removed, observe the damper returning to the normally-open position. NOTE: To remove power, disconnect one wire from the motor. 3.
PAGE 8
TRUEZONE ARD, EARD, AND ZD SERIES DAMPERS Resideo Inc., 1985 Douglas Drive North, Golden Valley, MN 55422 www.resideo.com 33-00040—03 M.S. Rev. 04-19 | Printed in United States This product is manufactured by Resideo Technologies, Inc., Golden Valley, MN, 1-800-468-1502 ©2019 Resideo Technologies, Inc. The Honeywell Home trademark is used under license from Honeywell International Inc. All rights reserved.