Owner's Manual
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
119 68-0312—03
Fig. 312. Inserting wires in thermostat terminal block.
Fig. 313. Inserting wires in EIM terminal block
IMPORTANT
Use 18–22 gauge thermostat wire.
Table 11. Wiring Diagrams by System Type.
System Type
Wiring Diagram
Reference
Standard Heat/Cool 314
Heat Pump with Auxiliary Heat 315
Geothermal radiant heat 316
Heat pump with oil forced air backup. 320
Geothermal radiant heat with geothermal
forced air and backup heat using separate
transformer for the radiant heat
321
Wood stove-fired hot water fan coil with
forced air furnace backup heat
322
Hot water radiant heat with backup heat
(single zone application)
323
Hot water radiant heat with backup forced
air heat. Zoned with forced air zone panel
and zone valves
324
Hot water radiant heat with backup forced
air heat. Zoned with forced air zone panel
and hot water panel.
325
Hot water fan coil with forced air furnace
backup heat.
326
Wood stove with heat pump and backup
electric strips. (For applications in which
the thermostat only needs to run the
blower fan when stove is hot).
Wiring IAQ Equipment or a stage of
Heating/Cooling to U1, U2 or U3 terminals
327–337
Wired Remote Sensors 342–346
Table 12. Zoning Diagrams by System Type.
System Type
Wiring Diagram
Reference
RedLINK VisionPRO thermostats with an
HZ432 zone panel and no IAQ control
347
RedLINK VisionPRO thermostat
controlling one zone with an HZ432 zone
panel and a TrueSTEAM humidifier
348
RedLINK VisionPRO thermostat with an
HZ432 zone panel and a ventilator
349
RedLINK VisionPRO thermostat with an
HZ432 zone panel and a TrueDRY
dehumidifier
350
S1
S1
W
Y
G
W2
Y2
A
S1
S1
O/B
Y
G
AUX
-E
Y2
L/A
K
RC
R
U1
U1
U2
U2
C
CONVENTIONAL
HEAT PUMP
R
C
Y
Y2
G
W
O/B
W2
AUX1
W3
AUX2
A
L/A