Owner's Manual
Table Of Contents
- Application
- Features
- Contents
- Specifications
- System Installation
- Installation Options
- Guidelines for Installing RedLINK Devices
- Installing Equipment Interface Module (if used)
- Wiring 24 Vac Common
- Selecting Discharge and Return Air Temperature Sensor Mounting Locations
- Installing Discharge and Return Air Temperature Sensors
- Selecting Thermostat Location
- Installing Wallplate
- Installing VisionPRO® 8000 with RedLINK™
- Wiring the Thermostat
- Remove Coin Cell Battery Tab
- Mounting Thermostat on Wallplate
- Power Optional RedLINK™ Accessories
- Performing Initial Setup
- Installer Tests
- Operation
- Setting the Time/Date
- Setting the Fan
- Setting System Mode
- Adjusting Program Schedules
- Overriding Schedules: Residential Use
- Overriding Schedules: Commercial Use
- Viewing Equipment Status
- Setting Vacation Hold: Residential Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Remote Setback: Commercial Use
- Adjusting Humidification Settings
- Adjusting Dehumidification Settings: Residential Use
- Adjusting Dehumidification Settings: Commercial Use
- Adjusting Ventilation Settings
- Ventilation Options
- Setting Preferences
- Cleaning the Thermostat Screen
- Adjusting Security Settings
- Viewing Dealer Information
- Advanced Features
- Installer Options
- Using the Temperature Display
- Using the Humidity Display
- Universal Outputs (U1, U2, U3)
- Universal Inputs (S1, S2, S3, S4)
- Data Logs
- Dry Contact Alerts
- Set Up the Dry Contact Alerts
- Staging Control
- Heat Pump and Backup Heat Operation
- Indoor Air Quality (IAQ) Control
- IAQ Reminders
- Customizable Reminders
- MicroSD card
- Commercial Features
- Overriding Schedules: Commercial Use
- Setting Holiday/Event Schedules: Commercial Use
- Setting Custom Events: Commercial Use
- Setting Holiday Schedule: Commercial Use
- Setting Holiday Override: Commercial Use
- Initiating Occupancy Mode: Commercial Use
- Ramp Rates (Commercial Use)
- Remote Setback (Commercial Use)
- Economizer and Time of Day (TOD) Operation
- Pre-Occupancy Purge
- Battery Replacement
- Optional Accessories
- Portable Comfort Control
- Remote Indoor Sensors
- Replacing a Thermostat
- Replacing an Equipment Interface Module
- Wiring
- Zoning
- Troubleshooting
- Regulatory Information
VISIONPRO
®
8000 WITH REDLINK™
15 68-0312—03
2. While the Press Connect message is displayed (listening
mode), press and quickly release the CONNECT button
on each new RedLINK accessory.
NOTE: For locations of CONNECT buttons on
RedLINK accessories, see “Locating the Con-
nect Buttons on RedLINK Accessories” begin-
ning on page 16.
Fig. 35. Thermostat in listening mode.
3. After a short delay (up to 15 seconds), check thermostat
to confirm the connection of each RedLINK accessory.
Touch or to review the list.
Fig. 36. Outdoor sensor added.
4. Touch Done at the thermostat after all new RedLINK
accessories are connected.
NOTE: Thermostat displays a countdown timer while in
the listening mode. If it detects no activity for 15
minutes, it exits listening mode.
Completing Initial Setup
5. Finish the setup by selecting the desired options. Touch
Done after you select the last option you want to change.
Fig. 37. Thermostat type.
The thermostat now displays its Home screen and the
thermostat setup is complete.
Fig. 38. Thermostat home screen.
Adding RedLINK Accessories to the
Thermostat
If you want to add RedLINK accessories after the thermostat
has been setup, follow these steps.
1. Touch Menu.
2. Select Installer Options.
Fig. 39.
3. Enter password (date code) and touch Done. See “Find-
ing Your Password (Date Code) to Access Installer
Options” beginning on page 19 for more information.
Fig. 40.
Press Connect on
New Accessories.
MCR33972
Outdoor Sensor
has been added
M34150
THERMOSTAT TYPE
programmable
M33985
MCR33976
Installer Options
MCR33977
Enter password
0 0 0 0