Product Overview

ManualsBrandsHoneywell Home ManualsDampers14 in. x 8 in. TrueZONE Rectangular Parallel Blade Damper

PRODUCT DATA

68-0247-03

ZD Series Dampers

NOTE: Pages 1-4 are for current ZD damper models. These models have "TZ" at the end of the model number.

Pages 5-8 are for legacy ZD series dampers.

APPLICATION

The ZD is a power close, and spring open damper. It has a

24-volt, spring-return, power-closed damper motor used

to control circulating air in heating, cooling and

ventilating systems. It is used when a normally-open

damper is required. The ZD is typically used with

Honeywell Home TrueZONE zone panels.

FEATURES

• Taping flange and non-interfering set screw.

• High temperature outer plastic for hot environments.

• Redesigned all metal drive train gears.

• Front facing display with LED Indication light for

open and close.

• Adjustable damper position range stops.

• Can be mounted on the side or bottom of the duct, as

the application requires. (Actuator mounted on

second damper dimension listed.)

• Quiet operation.

SPECIFICATIONS

IMPORTANT

The specifications given in this publication do not

include normal manufacturing tolerances.

Therefore, this unit may not exactly match the

listed specifications. Also, this product is tested

and calibrated under closely controlled conditions,

and some minor differences in performance can

be expected if those conditions are changed.

Dampers Frame: Solid construction using extruded

aluminum frame and blades.

Available Damper Sizes: See Table 1.

Damper Dimensions: All ZD dampers are actually sized

5/32 in. smaller than the listed size to ensure correct fit.

All ZD dampers are 4 in. thick.

M847D-ZONE Actuator Motor Electrical Rating:

24 Vac, 60 Hz, 8 VA.

Motor Electrical Connection: Push terminals.

Motor Nominal Angular Rotation: 90°.

Motor Torque: Minimum 71 in.-oz. (500 milli-newton

meters) output torque available when motor is

energized and device is at the spring return initial start

position.

Nominal Motor Timing at 77 °F (25 °C) Ambient:

Energized at rated load: 30 seconds.

De-energized (spring return): 10 seconds.

Motor Ambient Temperature Rating:

40 to 140 °F (5 to 60 °C).

Motor Shaft Rotation Direction: Clockwise, when

energized and viewed from the base or shaft end.

Motor Mounting Means: Direct connection to damper

shaft.

Motor Mounting Position: Multi-poise.

Motor Dimensions: See Fig. 1.

Summary of content (8 pages)

PAGE 1
ZD Series Dampers NOTE: Pages 1-4 are for current ZD damper models. These models have "TZ" at the end of the model number. Pages 5-8 are for legacy ZD series dampers. PRODUCT DATA SPECIFICATIONS IMPORTANT The specifications given in this publication do not include normal manufacturing tolerances. Therefore, this unit may not exactly match the listed specifications.
PAGE 2
ZD SERIES DAMPERS 4-31/32 (126) 4-41/64 (118) 4-1/16 (103) 3-61/64 (100) M35186 Fig. 1. Motor dimensions in inches (mm). ORDERING INSTRUCTIONS • Order ZD (dimension 1) x (dimension 2) TZ. Actuator is always mounted on dimension 2 side. All ZD dampers are 4 in. thick. — For example, ZD10x8TZ is a 10 in. x 8 in. damper with the actuator on the 8 in. side; but a ZD8x10TZ is a 8 in. x 10 in. damper that has the actuator on the 10 in. side.
PAGE 3
ZD SERIES DAMPERS INSTALLATION Installing the Damper IMPORTANT — Install dampers into a squared air duct. — Do not weld dampers to the air ducts. — Do not force dampers into undersized air ducts. Excess pressure can damage damper blades. — Be sure high limit setting is less than 200 °F (93 °C). Higher settings can damage the electric actuator. 1. Be sure the ZD is correctly sized to the air duct (see Selecting Damper Size section). 2. Select a ZD location that is three feet from the furnace plenum. 3.
PAGE 4
Wiring Multiple Dampers When the same zone controls two or more dampers, wire the dampers in parallel to terminals M1 and M6 on the zone control panel. RANGE STOP LOCATIONS Wiring a Motor See Fig. 2 for typical motor wiring hookup. a. For 2 wire usage, wire M1 and M6 (Fig. 2). b. For 3 wire usage, break the plastic tab to access M4. See Fig. 3. Changing a Motor M35187A NOTE: All ZD-series dampers (legacy and current models) can be used with the M847D-ZONE actuator. 1. 2. 3. 4. 5. 6. Fig. 4.
PAGE 5
Legacy ZD Series Dampers PRODUCT DATA SPECIFICATIONS ZD Side Mount ZD Bottom Mount IMPORTANT The specifications given in this publication do not include normal manufacturing tolerances. Therefore, this unit may not exactly match the listed specifications. Also, this product is tested and calibrated under closely controlled conditions, and some minor differences in performance can be expected if those conditions are changed. Available Damper Sizes: Even sizes from 6 in. x 6 in. up to 36 in. x 36 in.
PAGE 6
LEGACY ZD SERIES DAMPERS Selecting Damper Size * Nominal Device Dimensions (see FIg. 5.). inches mm A B C 2-3/8 3-3/8 3-1/2 60 84.5 88 To ensure correct operation, be sure to select the correct zone damper size for the air duct: IMPORTANT Be aware that damper sizes are built 5/32 in. smaller than the listed dimensional sizes. • If the damper is forced into an undersized air duct, the excess pressure can jam the damper blades and cause improper operation.
PAGE 7
WIRING Adjusting a Motor 1. CAUTION Personal Electrical Shock Hazard. Can cause electrical shock or equipment damage. Disconnect power before beginning installation. 2. The ZD has a 24 Vac, 50/60 cycle, 0.32 A motor. The ZD is wired to terminals M1 and M6 for power closed/spring return open. See Fig. 6. The ZD is a spring return damper that requires 24 V to the two motor leads to power the damper closed. When power is removed from the motor, the damper springs back to its normally-open position.
PAGE 8
www.resideo.com Resideo Technologies, Inc. 1985 Douglas Drive North, Golden Valley, MN 55422 1-800-468-1502 68-0247—03 M.S. Rev. 07-21 | Printed in United States © 2021 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.