Expanding Your System aaa. Maintenance and Use. Cara and Maintenance Replacing the Receiver Bi Troubleshooting Installing the Door 4 Specifications Door Camera Transformer Option. mm. 7 Declaration ., Checking Pack Content: St Hing UP concurrence Pro-instillation Setup . Door Camera... Thank you for choosing this Honeywell product. Please carry out the following the instructions to ensure correct installation and uss, and keep these notes in a sate place for future reference.
VISIONARY DOOR CAMERA FEATURES RECEIVER FEATURES DISPLAY. RE LESS =~ SCREENS THE CAMERA % IMAGE FOR APPROX.
Installation and Use Pr-installation setup Nate: Removing the cover also provides access to the nameplate, so now is a good time to write your name or other information, To use the nameplate, pull the end out from the side of the battery compartment, add your text at the end of the strip and carefully push it back into the slot. 2. Insert six AA-size alkaline batteries in the battery compartment at the back of the door camera as in the following diagram.
VISIONARY Ld HE EE ITS Charge the receiver batteries 1. Remove the battery isolating tab at the rear of the portable receiver. 2. Place the receiver onto the charging base and plug the charging base into a suitable mains socket. The battery indicator flashes slowly if this is the first time the unit has been powered up; the chime tunes play once the batteries have sough power, Before the next step, leave the unit to charge for at least three hours so that the batteries have enough power for the LCD screen.
Installation and Use Installing the door camera Position the door camera HORIZONTAL VERTICAL TOP VIEW Find a position for the door camera where ths call button is easy to press and the camera can ‘see’ visitors clearly. The following points are important: . The height needs to be between 4.5 and § ft. (1.3 and 1.5 m) above the ground or step where visitors normally stand. The camera is adjustable through a 30° total angle left to right, and 60° top to bottom.
VISIONARY stalling the door camera Position the receiver The receiver must be positioned within range of the door camera (i.e. less than typical building}. Test the system To ensure reliable operation, we recommend that both the door camera and receiver are sporadic up in their planned position(s), to check that the receiver has a good signal from the road camera.
Installation and Use stalling the door camera Mount the door camera Do not mount the camera in wet conditions as moisture or condensation will affect the internal parts. Once you have tested the system in place, mount the camera onto a wall or door as follows: 1. Remove the two sowers underneath the door camera. Unhook op and release the front and pull it away from the base. Note the TOP arrow on the base, 2.
VISIONARY stalling the door came! Door camera transformer option For installations where there is frequent use, typically more than five uses per day, the door camera can be powered using an 8-10 volt, 1 amp transformer. Important: Higher voltage transformer might damage the camera, Connect the low voltages output of the transformer to the road camera using suitable low voltage cable such as bell wire. Maximum recommended outer cable diameter mm). The cable run should not exceed 100 ft. 30m).
Installation and Use Installing the receiver Revolver operation When the call button is pressed on the door camera, the receiver chimes {provided the volume switch is not set to 0) and the camera images is displayed for about thirty seconds. If the caller presses the call button again, then the display time will extend to another 30 seconds.
VISIONARY Exp UCR eee) There are many ways to expand your entry system: you can connect your system to a television set or add more cameras, for example. TV connection You can connect the receiver to a TV set via the accessory RCA lead provided. Connect the stereo plug to the Visionary receiver unit and plug the yellow RCA plug to the TV AV input. Set the TV channel to the default AV channel for the said RCA input (refer to TV set instructions).
Installation and Use Maintenance and use CARE AND MAINTENANCE * Fingerprints or dirt on the door camera lens can cuss a dull or blurred picture. Occasionally use a soft, damp cloth to wipe the surface. Do hot usa cleaning products. Over-zealous or too frequent cleaning will scratch the surface and blur the picture. + Keep the receiver and charger base away from rain, liquids or risk of liquid spillage.
VISIONARY Troubleshooting The system does not work... + Make sure the door camera is powered, refer to below. * Marks sure the receiver is powered, refer to below. * Ova the receiver closer to the door camera to receive a better signal. + if new, make sure the door camera is programmed to the receiver ~ see ‘Installation Setup’ on page 3. Door camera is not powered... This is indicated when the red confidence light on the front does not light when the call button is pressed.
Installation and Use Troubleshoot A bops-beep tone sands for 30 seconds... This is an alert triggered by the tamper switch indicating someone is trying to unscrew and remove the door camera. Check outside immediately. The tons may sound if the screws that mount the front of the door camera to the rear are not fully screwed in place. Press any button on the receiver to stop the alert tone. The receiver switches on randomly...
VISIONARY Door Camera Recover Power requirement T10Y AC 210% via charger Battery type 8 x AA-size alkaline batteries 3X Assize NIGH batteries, minimum 1200mAn Battery operating fife typically one year" typically 3 days from full charge* Motion sensor range 121. {4 m) typical (fixed transitivity} NA Optional power via 8V to 10V 1A bell transformer* or 8-12V AC or DC supply NA Maximum number of transmitters Nea 4 (1, 2 with delectable chime tune: {video or door push) program.
DECLARATION Honeywell hereby declares that this product complies with Part 15 of the FCC rules and Industrial Granada standards. This device operation is subject to the following two conditions: (1) This device may not cuss harmful Interference, and {2) This device must accept any Interference received, including interference that may cause undesired operation.