User's Manual

5800FLOOD Flood Detector & Temperature Sensor
INSTALLATION INSTRUCTIONS Instructions d’installation
The ADEMCO 5800FLOOD Flood Detector & Temperature
Sensor is a wireless transmitter used with Honeywell’s alarm
systems that support 5800 series devices. Applications include
bathrooms, laundry rooms, boilers and basements etc.
The 5800FLOOD:
• can serve as a hot and/or cold temperature sensor via
internal thermal sensor
(sends alarm to control when temperature is lower than
45°F (Cold condition) or above 95°F, (Hot condition).
• can serve as a Water leakage or Flood Detector via built-in
metal contacts on the bottom of the unit
(sends alarm to control within approximately 40 seconds
after water has come in contact with the metal probes.)
• does not require external probes
• functions (modes) set by programming pre-defined device
loop numbers (see table 1) to separate zones in the control
panel.
• provides tamper supervision, which sends a trouble signal
to the control if the unit’s cover is removed.
INSTALLATION
Check Signal Strength: Before installing permanently,
conduct Go/No Go tests (see control's instructions) to
verify adequate signal strength from the planned location.
Adjust the device location as necessary.
Ce contact de porte / fenêtre sans fil est conçu pour être
utilisé avec les panneaux de commande Honeywell qui
supportent les dispositifs de la série 5800. Applications
include bathrooms, laundry rooms, boilers and basements etc.
The 5800FLOOD:
• can serve as a hot and/or cold temperature sensor via
internal thermal sensor
(sends alarm to control when temperature is lower than
45°F (Cold condition) or above 95°F, (Hot condition).
• can serve as a Water leakage or Flood Detector via built-in
metal contacts on the bottom of the unit
(sends alarm to control within approximately 40 seconds
after water has come in contact with the metal probes.)
• does not require external probes
• functions (modes) set by programming pre-defined device
loop numbers (see table 1) to separate zones in the control
panel.
• provides tamper supervision, which sends a trouble signal
to the control if the unit’s cover is removed.
INSTALLATION
Check Signal Strength: Before installing permanently,
conduct Go/No Go tests (see control's instructions) to
verify adequate signal strength from the planned location.
Adjust the device location as necessary.
 
Water Leak Detection
Place the device on the floor or other desired location near any
area that
potentially can be subject to a water leak condition
(ex. floor near or inside a kitchen cabinet, near the base of a
refrigerator, in a bathroom, basement, etc.).
Make sure the metal contacts at the bottom of the enclosure
are clean and free of any debris before positioning the unit in
place.
To ensure the unit remains in place, use the double-sided tape
to adhere unit to the floor or other surface.
IMPORTANT: After a water leak detection event, make sure the
contacts and the unit are completely dry and free of any
debris
before relocating the device.
Temperature Sensing
Mount the device low on a wall in the desired location with
double-sided adhesive tape (supplied).
If used solely as a temperature sensor, the 5800FLOOD can
be mounted low on a wall with double-sided adhesive tape
(supplied).
Water Leak Detection
Place the device on the floor or other desired location near any
area that
potentially can be subject to a water leak condition
(ex. floor near or inside a kitchen cabinet, near the base of a
refrigerator, in a bathroom, basement, etc.).
Make sure the metal contacts at the bottom of the enclosure
are clean and free of any debris before positioning the unit in
place.
To ensure the unit remains in place, use the double-sided tape
to adhere unit to the floor or other surface.
IMPORTANT: After a water leak detection event, make sure the
contacts and the unit are completely dry and free of any
debris
before relocating the device.
Temperature Sensing
Mount the device low on a wall in the desired location with
double-sided adhesive tape (supplied).
If used solely as a temperature sensor, the 5800FLOOD can
be mounted low on a wall with double-sided adhesive tape
(supplied).