Use Instructions Part 15

ManualsBrandsHoneywell International ManualsElectronicsKey fob security transmitter

N7674-3 4/05 PRELIMINARY

Honeywell International Inc.

5804AP

WIRELESS KEY

TRANSMITTER

INSTALLATION INSTRUCTIONS

For use with QED control panels ONLY!

GENERAL INFORMATION

The 5804AP is a compact, 4-button portable

wireless transmitter intended for use only

with wireless alarm systems that support

QED 5800AP series receivers. Each button

on the transmitter may be programmed for

any zone response, but is typically used for

arming, disarming, panic, and relay

activation. Each button's response is

assigned when programming the transmitter

at the control (see the QED control's

installation instructions).

The 5804AP is powered by two replaceable

lithium batteries designed to provide up to 4

years of life. For battery installation, see

Battery Access.

PROGRAMMING THE 5804AP

Each 5804AP is assigned a unique serial

number during manufacture. Each button on

the unit also has a distinct "loop" number

(refer to Figure 1 that you must programme

into the QED control panel during

installation. Assign each button to an

individual zone and designate the Input Type

as "BR" (Button Type RF). You must

program the lower left-hand button (Loop 4;

see Figure 1). If it is not programmed, a

"check" condition will occur when the button

is accidentally pressed.

You can also program the unit by entering

the serial number manually through a

keypad or by downloading it to the control

panel using Ademco's V-LINK Downloading

Software (Rev. 4 or higher). If you use one of

these methods, be sure to include the loop

number of each button (see Figure 1).

For complete details on how to program the

5804AP transmitter's serial number at the

control panel, see the QED control unit's

installation instructions.

Note: Buttons on this transmitter must be

pressed for at least 1/2 second to activate the

transmitter. This feature minimizes the

possibility of accidental transmissions.

YOU MUST

PROGRAMME

THIS BUTTON

LOOP 3

LOOP 1

LOOP 2

LOOP 4

Figure 1: 5804AP showing button designations

If you choose not to use the lower left-hand

button (Button 4), do the following:

1. Program it into the system anyway (see

previous explanation).

2. After the serial number has been

programmed, re-enter Zone Programming

for that zone.

3. At the "Zone Type" prompt, enter 00 and

press [*]. On VISTA 20/4111XM panels,

the system will ask whether you want to

permanently delete that zone. Enter 0

(No). This will cause the system to retain

the serial number, but render the button

inactive. On 4140XMPT2/VISTA-120

panels and above, continue to press [*]

until you see the "Enter Zone No?"

prompt. At this point, press 00 and [*].

Then enter *99 to exit program mode.

INSTALLING ADHESIVE LABELS AND

BUTTONS

The 5804AP is supplied with colored buttons

(red and blue) and colored adhesive

identification labels (blue, red, gray, and

green). Each label has a specified command

Summary of content (2 pages)

PAGE 1
N7674-3 4/05 PRELIMINARY 5804AP WIRELESS KEY TRANSMITTER INSTALLATION INSTRUCTIONS Honeywell International Inc. For use with QED control panels ONLY! GENERAL INFORMATION The 5804AP is a compact, 4-button portable wireless transmitter intended for use only with wireless alarm systems that support QED 5800AP series receivers. Each button on the transmitter may be programmed for any zone response, but is typically used for arming, disarming, panic, and relay activation.
PAGE 2
function and symbol printed on it, as well as an adhesive back for easy pasting. To paste a label on a button, slowly peel off a label with a selected function and paste it on the button of the transmitter. If you decide later to reprogram a button, the label can be easily removed or a new label pasted over the existing one. Additional colored buttons (red and blue) are also provided which can be used with or without the labels.