Installation Guide

ManualsBrandsHoneywell International ManualsElectronicsWireless keypad

Preliminary - 6 September 2002

K0903ax 9/6/02

5).(<3$'75$16&(,9(

INSTALLATION GUIDE

GENERAL INFORMATION

The 6160RF keypad/transceiver is a is a combination unit

that contains the following:

• A 6160 Alphanumeric Addressable Keypad

• A 5881M RF Receiver

• A 5800TM Transmitter Module

The 6160RF Keypad/Transceiver may be used on any

control panel that supports the 6160 Keypad (e.g., VISTA-

10SE, VISTA-15, VISTA-20SE, VISTA-40, VISTA-50P).

FEATURES

Wireless Features

• Supports wireless key transmitters (5804, 5804BD).

• Supports wireless keys with Signal Sentry (high-

security) (5804E).

• Provides a nominal range of 200' for the RF

transmitters (some transmitters have a shorter range).

• Supports RF jam detection when the receiver is enabled.

The following transmitters are not intended for use in UL

installations: 5804, 5804BD, 5804BDV, 5804E and 5827BD.

Programming Features

• Provides default settings for the functions of the

wireless keys.

• Provides a method to enroll up to eight (8) encrypted

(high security) devices.

Additional Features

• Provides tamper protection that causes the system to

annunciate a trouble condition if the cover is removed.

(If supported by the control panel). The tamper switch

has not been evaluated for UL installation.

• Capable of sending status signals (Armed, Ready, etc.)

to bi-directional units such as 5804BD, 5804BDV and

5827BD.

APPLICATION GUIDELINES FOR THE 6160RF

Use the following guidelines when planning an

installation:

• If using bi-directional devices, be sure to enable the

transmitter module in the 6160RF.

• If transmitters are programmed into the control

panel, be sure to enable the receiver. (Make sure you

do not exceed the number of receivers supported by

the control panel.)

• You must set the House ID only if you are using RF

keypads and/or bi-directional devices;

AND

the House

ID Source is the 6160RF (Local).

Note:

If the House ID source is the panel, enter *99 into keypad.

6160RF Application Guide

The guide, provided below, outlines how to program the

wireless keys, RF receiver, and the House ID in the

6160RF for your particular installation.

* Two 6160RFs are needed for this application: one connected to partition 1’s keypad terminals, and

one connected to partition 2’s.

** If using an RF keypad on only one partition, the 6160RF’s partition assignment must match the

partition set in field 1*48.

*** If set for Local on a partition control, the 6160RF’s partition assignment must match the one

programmed in the BD device.

Control Panel

RF keypads and/or

Bi-directional

devices on more

than 1 partition?

Program

RF Receiver

House ID

Source

***

VISTA-10SE, VISTA-15,

VIA-30PSE

NO Enable System

VISTA-20SE NO Enable System

YES* Disable Local

VISTA-40, VISTA-50P NO** Enable System

YES Disable Local

Summary of content (4 pages)

PAGE 1
Preliminary - 6 September 2002 K0903ax 9/6/02 5) .(<3$' 75$16&(,9(5 INSTALLATION GUIDE GENERAL INFORMATION Additional Features The 6160RF keypad/transceiver is a is a combination unit that contains the following: • A 6160 Alphanumeric Addressable Keypad • A 5881M RF Receiver • A 5800TM Transmitter Module The 6160RF Keypad/Transceiver may be used on any control panel that supports the 6160 Keypad (e.g., VISTA10SE, VISTA-15, VISTA-20SE, VISTA-40, VISTA-50P).
PAGE 2
Preliminary - 6 September 2002 b. If desired, wires may be strain-relieved to the wire tie point on the inside of the case back with a tie wrap (not supplied). INSTALLING THE 6160RF Locate the 6160RF in an area and at a height where it is convenient for user operation. The 6160RF must be at least 10 ft from the control panel to ensure proper operation of the RF receiver. 3.
PAGE 3
STEP 1. 2. 3. 4. DESCRIPTION Enter the program mode by pressing the [1] and [3] keys simultaneously for a few seconds within 30 seconds after applying power or within 30 seconds after removing the case back. (Keypad Address) Enter the two digit keypad address. Press the [✳] key to continue. (Receiver Enable) Enter [1] to enable, or [0] to disable Receiver. Enable the receiver if RF transmitters or wireless keypads are programmed into the control. Press the [✳] key to continue.
PAGE 4
TROUBLESHOOTING The error messages listed in the following table cause the 6160RF to produce a single ding tone. The table describes the error messages and the corrective actions. Display Probable Cause Lb Low battery in the wireless key Open Ckt Incompat. Con. Check 09 Open circuit Incompatible connection Corrective Action 1. Replace the battery if the wireless key has a replaceable battery. 2. Replace the transmitter if the wireless key does not have a replaceable battery.