User's Manual

ManualsBrandsHoneywell International ManualsElectronicsKeypad Transceiver

ADEMCO 6162RF Keypad / Transceiver – Installation and Setup Guide

Alphanumeric Addressable Keypad/Transceivers for use with Honeywell Control Panels; incorporates functions

of a High RF Receiver and a 5800 Transmitter module.

= READY to Arm

= NOT READY to Arm

= System ARMED

= System NOT ARMED

Arming Keys

6162: 4-Line Alpha Display

Custom Zone Designators

6162rf-KEYPAD-LBLD-V0-032713

Programmable Function Keys

Sounder

Wall

Surface

Control Panel Terminal Strip

AU X DATA

DATA

OUT

AUX

To Control Panel

Terminal Strip

Optional Front Cover Securing Screw

(Required in European Installations)

Install Four (4)

Mounting Screws

Control Panel

1. OPEN

Keypad

Front Cover

2. WIRE

3. MOUNT

• Connect only one wire per terminal.

• For Daisy-Chain Configurations, use

wire splicing so only one wire is

connected to each terminal.

• Mount on drywall, or in

a single or double-gang

electrical box.

6162RF-installation-3-21-13

Black (Gnd)

Red (+12vdc)

Green (Data To Control)

Yellow (Data From Control)

To activate Function keys,

press and hold key for at

least 2 seconds; key pairs

are activated immediately.

Table 1 – Programmable

Function Keys

A or

and

B or and

C or and

Note: See the control's instructions for

details on programming the Function

keys for panic alarms or other special

functions (i.e., macros).

• Supports wireless key transmitters

(e.g., 5834-4) and bi-directional

transmitters (e.g.; 5804BD,

5828/5828V).

• Supports wireless keys with high-

security (encryption) capability (e.g.;

5834-4).

• Provides a nominal range of 200

feet for RF transmitters (some

transmitters have a shorter range).

• Supports RF jam detection.

Table 3 – Icon Descriptions

ICON DESCRIPTION

TEST SYSTEM

BYPASS ZONES

ASSIGN CODES

CHIME MODE

ARM MAXIMUM

ARM INSTANT

ARM AWAY

ARM NIGHT STAY

DISARM

ARM STAY

SETTINGS

Table 2 – Settings Ke

Settings Ke

Result

Press

Displays Settings Menu*:

1 Set Time/Date

2 View Event Log

3 Reboot Keypad

4 Set User Code**

* Follow instructions in the User Guide for these options; selecting

option 3 reboots the 6162 keypad.

** Set User Code option available only with the following Control

Panels: VISTA-10P Rev 4.16, VISTA-15P Rev 9.16, VISTA-

20P Rev 9.16 and VISTA-21iP Rev 3.16.

GO TO PAGE 4

FOR FCC / IC

INFORMATION

Summary of content (4 pages)

PAGE 1
GO TO PAGE 4 FOR FCC / IC INFORMATION ADEMCO 6162RF Keypad / Transceiver – Installation and Setup Guide Alphanumeric Addressable Keypad/Transceivers for use with Honeywell Control Panels; incorporates functions of a High RF Receiver and a 5800 Transmitter module. 6162: 4-Line Alpha Display Custom Zone Designators • Supports wireless key transmitters (e.g., 5834-4) and bi-directional transmitters (e.g.; 5804BD, 5828/5828V). • Supports wireless keys with highsecurity (encryption) capability (e.g.; 5834-4).
PAGE 2
APPLICATION GUIDELINES FOR THE 6162RF Table 4 – Application Guidelines If… This is the only transceiver on the system, And… You want to use both the receiver and transmitter function on a single-partition system, Then… • Set the keypad to a device address assigned to the desired partition.* • Enable the receiver. • Program a system House ID in the control panel (this will enable the transmitter function).** • Set the wireless devices that will communicate with this 6162RF to the same system House ID.
PAGE 3
Table 5 – 6162RF Programming (continued) STEP DESCRIPTION 6. DISPLAY House ID. This prompt will only appear if the receiver is disabled. If the receiver is enabled the 6162RF will use the House ID programmed in the panel. Refer to Application Guidelines section when selecting a House ID.
PAGE 4
TROUBLESHOOTING The error messages listed in the following table cause the 6162RF to produce a single ding tone. The table describes the error messages and the corrective actions. Table 8 – Troubleshooting Display Probable Cause Open Ckt Check 100 RF Receiver Check 8xx* No data is being received from the control panel. 1. The control panel does not see the 6162RF Receiver, or the Receiver is not functioning. 2. Another device on the keypad terminals is conflicting with this receiver address.