Quick Install Guide

ManualsBrandsHoneywell International ManualsElectronicsVista Automation Module

Table Of Contents

Untitled

VAM (VISTA Automation Module) - Installation & Setup Guide

Introduction

VISTA Automation Module (herein referred to as “VAM”) combines home automation and home security and is intended

for use with compatible VISTA

series control panels. VAM includes a built-in web server, Wi-Fi

capability, and Z-Wave

technology allowing VISTA installations to support Z-Wave devices.

The VISTA Automation Module also supports Remote Services for controlling Z-Wave devices and Scenes remotely from

an associated Total Connect™ account.

VAM is controlled using a web browser on a Wi-Fi enabled smart device such as a Tablet PC, laptop, Smartphone, etc.

DISPLAY NOTE: For optimum viewing of the screens and menus, the tablet’s font size setting may need to be adjusted.

Make

iring

Connections

Connect VAM to the control panel’s keypad data (ECP)

terminals using a standard 4-wire keypad connector harness.

vam-003-V1

CONTROL PANEL

ECP TERMINALS

YELLOW

RED

BLACK

GREEN

CONTROL PANEL

PC BOARD

VAM

REFER TO THE CONTROL PANEL’S INSTRUCTIONS

FOR MAXIMUM WIRE LENGTHS.

4-WIRE CONNECTOR HARNESS

Wire Connections to the Control Panel

Verify that VAM and other connected devices do not ex

ceed the

control’s Aux Power output capability. If it does, use a

supplementary power supply as shown.

IMPORTANT: When VAM is powered from an auxiliary power

supply, always apply power to the control panel first and then

VAM. Failure to observe this sequence results in improper

operation of VAM and may result in an ECP Error indication.

pwr_supp_conn-011-V0

BLACK

POWER FROM SUPPLEMENTARY

POWER SUPPLY IF USED

BLACK

GREEN

YELLOW

CONTROL

TERMINAL STRIP

SUPPLEMENTARY

+12 VDC

POWER SUPPLY

P/N AD12612

DATA

OUT

AUX

Supplementary Power Connections

Mount

the VAM

VAM is for indoor use only and should be mounted near the control

panel or a keypad connected to the control panel for ease of wiring.

VAM mounts to a wall surface by hanging on two screws. See the

diagram below.

• Leave the screw heads 1/8” above the wall surface.

• If necessary, drill a hole in the wall for the wire harness to pass

through.

• Connect the wire harness to the VAM before mounting.

MOUNTING SCREW

DRILL 3/16” DIA. HOLES 2 PLACES

1.65”

2.5”2.54”

vam-004-V0

Insert an SD/SDHC Memory Card

An SD card must be installed to receive automatic software

upgrades. The SD card can be left in the VAM. See Software

Upgrades section.

• Avoid touching the contacts on the card

• 4GB SD card supplied

• Supports up to 16GB SD Card

Insert the memory card (SD/SDHC Card) as shown.

INSERT

SD CARD

EXHIBIT 7-1

CFS8DLVAM / 573F-VAM

EXHIBIT 7-1

PLEASE GO TO THE BOTTOM OF

PAGE 7 FOR FCC / IC AGENCY

STATEMENTS.

Summary of content (7 pages)

PAGE 1
EXHIBIT 7-1 PLEASE GO TO THE BOTTOM OF PAGE 7 FOR FCC / IC AGENCY STATEMENTS. CFS8DLVAM / 573F-VAM EXHIBIT 7-1 VAM (VISTA Automation Module) - Installation & Setup Guide Introduction VISTA Automation Module (herein referred to as “VAM”) combines home automation and home security and is intended for use with compatible VISTA® series control panels. VAM includes a built-in web server, Wi-Fi® capability, and Z-Wave® technology allowing VISTA installations to support Z-Wave devices.
PAGE 2
Front Panel LEDs Set Up the WiFi Network To set up the WiFi network for VAM, you will need the following: • Wi-Fi enabled smart device (Tablet PC, laptop, Smartphone, etc.) • VAM SSID and WPA2 password (located on the VAM’s label) • VAM default IP address: 192.168.2.1 • Home router SSID and WPA2 password (typically located on the home router’s label); home router must use WPA2 encryption and have a password (key) assigned.
PAGE 3
Program the Control Panel for using VAM Set Up Email Notification At the control, assign an appropriate touchscreen (AUI) type device address (ECP address) for VAM, and set a partition (if applicable). Refer to the control panel’s programming instructions for detailed procedures. After enabling the VAM device address in the control panel, set the VAM to the selected address. See section below.
PAGE 4
Adding Z-Wave Devices Automation & Creating Scenes EXISTING NETWORK NOTE: Z-Wave products from other manufacturers can be included (added) into the VAM network. Z-Wave devices that are always powered can serve as repeaters regardless of manufacturer. To add (include) Z-Wave devices in VAM, log in to the VAM home screen, then do the following: Light, Switch, Outlet Modules 1. Install device according to the manufacturer’s directions. 2. Click Automation > Z-Wave Setup > Z-Wave Enroll / Add. 3.
PAGE 5
Z-Wave Troubleshooting Navigation & Menu Icons • Cannot add new device Make sure the Z-Wave device is within range of the VAM. You may need to move the device closer to the VAM. Refer to the ZWave device Instruction Guide for proper range. To aid in the navigation through the VAM WIFI screens, a set of user-friendly icons has been provided. • Device is within proper range but still is not included 1. At the VAM: a.
PAGE 6
Software Upgrades Set Up Remote Access (Account Setup) Software upgrades may be available for this product. These upgrades can be installed manually, or you can set VAM to notify you that an upgrade is ready and have it automatically installed. Remote access lets the user access VAM’s menus directly via the Internet when away from home. The home router must first be configured for port forwarding. Refer to the router’s instructions for details on port forwarding.
PAGE 7
FEDERAL COMMUNICATIONS COMMISSION (FCC) AND INDUSTRY CANADA (IC) STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use.