Volume Control Use the Dolphin keyboard to adjust the volume. & VOL Blue To raise the volume, press the Blue modifier key + up arrow. To lower the volume, press the Blue modifier key + down arrow. & Blue PG Or Press the up or down arrow on the Volume Control button on the right side of the device to adjust the volume of the active speaker, see Volume Control Button on page 3-10.
Sending Calls SEND After the number is dialed, tap Talk Note: The or press the Blue + Send key . icon indicates that the phone is in use. Ending Calls END While the phone call is live, tap End or press the Blue + End Key . Accessing Voice Mail Tap > Phone > Speed Dial > Voice Mail > Call. Note: Update the voice mail retrieval number by turning the phone OFF and then ON via the Dolphin Wireless Manager, see Enabling the WWAN Radio on page 9-5.
Security The Security screen provides access to establish or change your security PIN. Check the box next to, “Require a PIN when the phone is used” to enable the PIN security feature. Services For each service, the phone reads settings from the network stored on the SIM card and then displays the available options from the carrier on the screen. To customize the settings, select it from the list and tap “Get Settings”.
Network You can find, select, and set your preferred network order from the Network screen. Data Communication (GSM/HSPA+ Global Radio Dolphin Models) You set up data communication via the Connections Manager. The carrier on the SIM card is the ISP. System Requirements • The GSM radio must be enabled; see Enabling the WWAN Radio on page 9-5. • You must have an active SIM card with a DATA plan installed; see SIM Card Installation on page 9-3.
3. Enter a name for the connection. Select Cellular Line (GPRS) as the modem. Tap Next. 4. Enter the Access point name. Tap Next. 5. Enter the user name and password from the account. Tap Finish.
. The connection you just created should appear in the list on the modem tab. 7. Tap and hold on the connection. Select Connect on the popup menu. 8. The network icon in the Title bar indicates the GSM radio is attempting to connect . Note: When the device is on a 2G (EDGE/GPRS) network, a data connection failure occurs if the phone is in use for a voice call while attempting a data connection. Simultaneous voice and data use is only supported if the device is on a 3G network.
1. When an active SIM card is inserted in the terminal, tap > Settings > Personal > Phone > Menu > Options. 2. Select the Network tab. 3. Under Network selection, select Automatic (the default selection) or Manual. a. If you select Manual, the Phone searches for available networks. b. The found networks appear. c. Select a new network and tap OK. The Phone registers on the new network and the Network tab appears. d.
Data Communication GSM/CDMA Dolphin Models Gobi Manager The Gobi Manager enables you to see real time status of the radio, setup your Network selection, view you’re profile and scan for networks. The Gobi Manager contains four tabs: Status, Setup, Profile, and About. 1. Tap 2. Tap Menu. 3. Select Gobi Settings. Status Tab on the Home screen to access the Dolphin Wireless Manager. The Status tab contains the real time radio status information including: • The power status of the radio (e.g.
Profile Tab The Profile tab allows you to see Radio capability information and network statistics including: • • • • About Tab Radio Hardware and Software versions Radio and SIM identification numbers Serving network connection type and state Available radio interfaces for the current serving network Displays copyright and version information for the Gobi Connection Manager. Establishing Data Communication 1. Tap on the Home screen to access the Dolphin Wireless Manager. 2.
Working with the Bluetooth Radio Enabling the Bluetooth Radio You enable the Bluetooth radio in the Dolphin Wireless Manager (see page 8-6). 1. Tap on the Home screen to access the Dolphin Wireless Manager. 2. Tap anywhere inside the Bluetooth rectangle and Bluetooth begins activating. 3. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON. Now, the Bluetooth radio is transmitting a signal.
Pairing and Trusted Devices The terminal does support pairing. Pairing happens during general connection setup. Paired devices are "trusted" devices. This means that there is unrestricted access to all services (including services that require authorization and authentication). A connection can exclude pairing. A device that is connected to the terminal but not paired with it is considered an untrusted device.
4. Select a device from the list and tap Next. The types of devices in the vicinity of the radio appear in the list of discovered devices. 5. You are prompted to enter a passcode. • If the device has a specific passcode, enter it in the Passcode field and tap Next. When attempting to connect to a printer or headset with Bluetooth capabilities, the passcode may default to either 1111 or 0000. If there is no default, consult the device literature for the number.
8. When the connection is complete, a list of matching and supported services on the device appears. Only the services that are mutually supported on both devices appear in the Partnership Settings window. 9. Select the services you want to use and tap Save. The services on the new devices have to be selected or the pairing won’t include those services, even though the devices are paired. If services are not selected, you will be continually re-prompted for the passcode from the device. 10.
Transferring Files 1. Tap > File Explorer. 2. Navigate to the file you want to transfer. 3. Tap and hold on the file and select Beam File on the popup menu. 4. The Bluetooth radio begins searching for devices. When a Bluetooth device is first found, it appears as an Unknown device; the icon indicates that the device is a Bluetooth device. As data is retrieved, the device IDs appear in the list. 5. Tap the device to begin sending the selected file. 6.
Making the Terminal Discoverable By default, the Dolphin terminal is not discoverable, which means that the terminal will not be found by other Bluetooth devices. To make the terminal discoverable, tap Mode on the Horizontal scroll. Select Make this device visible to other devices and tap OK. Selecting COM Ports You can select COM ports 0-9. For more information, see 99EX and 99GX COM Port Assignment Table on page 8-13.
11 Working with GPS Overview The Dolphin 99EX terminal contains an integrated GPS module that allows location tracking of workers and vehicles, providing better utilization of field assets. Optional mapping and navigation software provides turn-by-turn driving directions and location information. Note: Dolphin 99GX models are not currently offered with GPS capabilities.
Other baud rates are not possible. The baud rate selected on COM7 is the actual baud rate with which the GPS communicates. GPS Intermediate Driver When the first user of GPD1 opens the port, the GPS Intermediate Driver opens the COM7 port. The GPS Intermediate Driver allows multiple applications to open GPD1, and the GPS data is broadcast to all open ports. When the GPSID driver is in use, the COM7 port is allocated to GPSID as READ|WRITE (COM7 is still available for access mode of 0).
12 Dolphin 99EX HomeBase Device (Model 99EX-HB) Overview As the hub of your Dolphin system, the Dolphin 99EX HomeBase (99EX-HB) charging and communication cradle supports both RS232 and USB communications, which make it able to interface with the majority of PC-based enterprise systems. The 99EX-HB charger is designed for use with battery pack models 99EX-BTSC (standard Li-poly 3.7 V, 11.3 watt hour) and 99EX-BTEC (extended Li-ion 3.7 V, 18.5 watt hour) manufactured for Honeywell International Inc.
Convenient Storage The intelligent battery charging system makes this base a safe and convenient storage receptacle for your Dolphin terminal. Capacity The base holds one terminal and features an auxiliary battery well behind the terminal well that can charge a battery pack independently of the terminal well. This means that one base can charge two battery packs: the one installed in the terminal and a spare. ! ! We recommend use of Honeywell Li-ion or Li-poly battery packs.
Power/Dock LED Indicates if power is supplied to the HomeBase and if a terminal is docked properly in the base. This color means… Red The HomeBase has power but no terminal is docked. Green The HomeBase has power and the terminal is properly seated in the base. AUX Battery LED Indicates status of the battery charging in the auxiliary battery well; see Back Panel on page 12-4. This color means… Orange The auxiliary battery is charging.
Back Panel Auxiliary Battery Well USB Port DC Power Jack RS232 Port Auxiliary Battery Well The base enables you to charge an additional battery pack independently of the terminal well in 4 hours for the standard 3.7V battery or 6 hours for the extended 3.7V battery. This feature ensures that you can always have a fully-charged battery for your terminal. See Charging a Spare Battery in the Auxiliary Battery Well on page 12-6. USB Port This USB port is USB v2.0 Hi-Speed compliant.
Bottom Panel For details on how to mount the HomeBase, see Mounting the HomeBase on page 12-9. Serial Number Label Compliance Label Power The base requires 12 Volts DC input for communications, battery charging, and power output to the terminal; the power adapter included with the base converts the voltage from the AC power source to 12 Volts DC. Use only UL listed power supply, which has been qualified by Honeywell, with output rated at 12VDC and 3 amps with the device.
Charging the Main Battery The base powers the terminal and fully charges its main battery pack in 4 hours for the standard battery or 6 hours for the extended battery. The terminal contains an intelligent battery charging system that protects the battery from being damaged by overcharging. The unit senses when a battery pack is fully charged and automatically switches to a trickle charge that maintains the battery at full capacity.
Communication USB Dolphin terminals support USB communications out of the box. The base also supports USB communications via the USB port located on the back. The base acts as a USB device by interfacing the USB signals of the Dolphin terminal to the USB of the host workstation. Using a standard USB cable, the base’s USB interface allows the Dolphin terminal to communicate with a workstation. RS232 The base supports RS232 communications via the RS232 Communications Port located on the back of the device.
• If the base is connected to the workstation, the Dolphin terminal automatically opens ActiveSync or the Windows Mobile Device Center to establish a connection. 2. The base can now transfer data between the terminal and the host device. If communication does not occur, check the port connections to ensure that the cradle is correctly configured. Verifying Communication You can verify that the USB driver is functioning by watching the COMM LED on the USB base.
Serial Connector The following diagram displays the pin diagram of the serial connector of the base. Pin Description 1 Internal Jumper to Pin 6 2 TXD 3 RXD 4 No Connect 5 GND 6 DTR 7 CTS 8 RTS 9 RI Note: The signal names are referenced to the terminal. The terminal is a DCE RS232 device. Refer to section, RS232 Communications Cables and RS232 Pin Configuration for more details. The base is at a right-angle to the printed circuit board (PCB). The ninth pin has a ring indicator (RI).
12 - 10
13 Dolphin 99EX eBase Device (Model 99EX-EHB) Overview The Ethernet Base (eBase) enables a single Dolphin 99EX or 99GX computer to communicate with a host device over an Ethernet network. The 99EX-EHB charger is designed for use with battery pack models 99EX-BTSC (standard Li-poly 3.7 V, 11.3 watt hour) and 99EX-BTEC (extended Li-ion 3.7 V, 18.5 watt hour) manufactured for Honeywell International Inc. and with Dolphin 99EX and 99GX model terminals.
Parts and Functions Front Panel Terminal Well Auxiliary Battery Well Power/Dock LED COMM LED AUX Battery LED Terminal Well Place the terminal in this well to communicate with a host device, power the terminal, and charge the installed battery pack. The eBase completely charges the main battery in a Dolphin terminal in 4 hours for the standard 3.7V battery or 6 hours for the extended 3.7 battery. Auxiliary Battery Well See Auxiliary Battery Well on page 13-4.
This color means… Red Flashing The internal temperature of the auxiliary battery is too hot or there is a battery error. Charge the auxiliary battery in a cooler environment or replace the battery with a Honeywell Li-ion or Li-poly battery. COMM LED The COMM LED indicates the status of data transfer between the Dolphin terminal and the eBase.
Back Panel Auxiliary Battery Well Green LED USB Port Yellow LED DC Power Jack RJ45 Ethernet Port Auxiliary Battery Well The eBase enables you to charge an additional battery pack independently of the terminal well in 4 hours for the standard 3.7V battery or 6 hours for the extended 3.7V battery. This feature ensures that you can always have a fully charged battery for your terminal. USB Port This USB port is USB v2.0 Hi-Speed compliant.
DC Power Jack Use the power cable from Honeywell that comes with the eBase to supply power to this power jack. For more information, see Power on page 13-5. Bottom Panel For details on how to mount the eBase, see Mounting the eBase on page 13-8. Serial Number Label MAC Address Label Compliance Label Power The terminal requires 12 Volts DC input for communications and battery charging; the power adapter on the power cable converts the voltage from the power source to 12 Volts DC.
Charging the Main Battery The eBase provides power to the Dolphin terminal and allows the charging of the terminal’s main battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which means that Dolphin terminals may be stored in the eBase indefinitely without damage to the terminals, battery packs, or the eBase. To check battery power, use the Power system setting; see Power on page 7-16.
• The Kernel version must be 26.01 or later in terminals running Windows Embedded Handheld 6.5 Classic. • In terminals running Windows Embedded Handheld 6.5 Professional, the kernel version must be 25.01 or later. Applications on the Dolphin Terminal Applications running on the Dolphin terminal when it is connected to the eBase should be designed specifically for a partially connected network. For more details, please refer to the Best Practices for Partially Connected Networks document available at www.
Setting Up and Connecting the Dolphin Terminal to the eBase 1. Verify the base has power. If the Power/Dock LED is not illuminated, see Connecting Power to the eBase on page 13-5. 2. Plug the USB communication cable into the USB port on the back of the eBase. Note: The Dolphin terminal should always be removed from the eBase when connecting or disconnecting the USB cable. 3. Connect the other end of the USB cable to the host workstation. 4. Insert the Dolphin terminal in the eBase terminal well.
14 Dolphin 99EX Mobile Base Device (Model 99EX-MB) Overview The 99EX-MB charging and communication cradle is designed specifically for in-premise and in-transit data collection applications. It features a flexible mounting bracket and a cigarette lighter adapter to adapt it to your environment. The 99EX-MB is designed for use with Dolphin 99EX and 99GX model terminals using battery pack model 99EX-BTSC (standard Li-poly 3.7 V, 11.3 watt hour) or 99EX-BTEC (extended Li-ion 3.7 V, 18.
Front Panel Terminal Lock (not in view) Terminal Lock Terminal Well Volume Control Dial (not in view) Ball Joint for Mounting Bracket Status LED Speaker USB Communications Port Mounting Bracket Used to mount the base to a fixed location. Speaker Amplifies the Dolphin’s audio signals. Status LED Illuminates solid green when the Dolphin terminal is properly seated in the terminal well. Terminal Locks The mobile base has a locking switch on the left and right side.
Bottom Panel The power supply and RS232 connectors are located on the bottom of the unit. Power Supply Connector RS232 Communications Port Power Supply Connector To run on vehicle power, you can use the 12 VDC cable. The appropriate cable comes with the kit you ordered. The 12 VDC cable can be used with a cigarette lighter outlet. ! Verify that the power source is always within the specified range and observe correct input voltage polarity.
Back Panel and Mounting Brackets Bracket Base Mounting Bracket Turnscrew USB Port Ball Joint Power supply and RS232 connectors (not in view) Ball Joint Ball Joints There are two ball joints: one on the back of the base and one on the mounting bracket. Both ball joints are inserted into the bracket and secured to mount the base. Connectors The power and RS232 connectors are located on the bottom panel. For more information, see Bottom Panel on page 14-3.
Mounting The adjustable mounting bracket holds the terminal securely in place and gives the user a variety of options for mounting the base. Safety Precautions Honeywell is not responsible for any damages caused to you, your vehicle, or other individuals due to the installation of the Dolphin Mobile mount.
Powering the Dolphin Terminal When seated in a base that is connected to the appropriate power source, the Dolphin terminal receives the power to charge its main battery and run its internal circuitry. Keep the base plugged into the power source so that the Dolphin terminal battery pack stays fully charged. Note: Honeywell recommends that you leave the base connected to its power source at all times. The base is powered via the power connector on the bottom panel; see Bottom Panel on page 14-3.
Establishing ActiveSync or Windows Mobile Device Center Communication The Dolphin terminal is usually auto-detected and configured by ActiveSync or Windows Mobile Device Center based on the communication cable. The synchronization software automatically sets up an RS232 connection when you are using an RS232 cable. For more details, see Connecting and Synchronizing the Terminal and Workstation on page 8-8.
Serial Connector The following diagram displays the pin diagram of the serial connector of the base. Pin Description 1 Internal Jumper to Pin 6 2 TXD 3 RXD 4 No Connect 5 GND 6 DTR 7 CTS 8 RTS 9 RI Note: The signal names are referenced to the terminal. The terminal is a DCE RS232 device. Refer to section, RS232 Communications Cables and RS232 Pin Configuration for more details.The ninth pin has a ring indicator (RI).
15 Dolphin 99EX ChargeBase Device (Model 99EX-CB) Overview The 99EX ChargeBase is a 4-slot charging cradle that can power 4 Dolphin terminals, and charge their main batteries in 4 hours for the standard battery or 6 hours for the extended battery. The 99EX-CB charger is designed for use with battery pack models 99EX-BTSC (standard Li-poly 3.7 V, 11.3 watt hour) and 99EX-BTEC (extended Li-ion 3.7 V, 18.5 watt hour) manufactured for Honeywell International Inc. and with Dolphin 99EX and 99GX model terminals.
Parts and Functions Front Panel Terminal Wells Power/Dock LED Charge LED Terminal Wells The base contains four terminal wells. Each well has its own dedicated Power/Docking LED and Charging LED indicator. Power/Dock LEDs The Power/Dock LED indicates if the ChargeBase has power and if the terminal is properly seated in the terminal well. Each terminal well has its own dedicated Power/Dock LED. This color means… Red The ChargeBase has power but no terminal is docked.
Back Panel Power Supply Connector Power Supply Connector This connector receives input from the power adapter. Plug the power connector cable from the power adapter into this connector. Power The terminal requires 12 Volts DC input for battery charging; the power adapter on the power cable converts the voltage from the power source to 12 volts DC. Use only UL Listed power supply, which has been qualified by Honeywell with output rated 12VDC and 8.5 amps with the device.
Charging the Main Battery The base provides power to the Dolphin terminals and allows charging of the main batteries in the terminals. The main battery of each terminal charges in 4 hours for the standard 3.7V battery or 6 hours for the extended 3.7V battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which means that Dolphin terminals may be seated in the base indefinitely without damage to the terminals, battery packs, or the base.
Hardware Required • 3/16 in. dia x 5/8 in. long pan head screw • 1/2 in. OD x 7/32 in. ID x 3/64 in. thick washer • 3/16 in. dia nut Installing the DIN Rail 1. Slide the DIN Rail into the DIN Rail slot on the bottom panel of the base. 2. Turn the base and DIN Rail right side up. 3. Then, using the appropriate hardware, secure the DIN Rail to a stable, flat horizontal surface. DIN Rail (7.
Hollow Wall Installation 1. Drill four pilot holes in the wall using a 7/8 in. drill bit. 13.78 in. [35 cm] 6.5 in. [16.5 cm] 2. 3. Wall Mount Bracket Wall Mount Holes Slide the bolt through the wall bracket, and thread the toggle nut onto the bolt. Press the ends of the toggle nut together, and insert the bolt/nut into the pilot hole until the nut clears inside wall surface. The toggle nut should spring open preventing the screw from being removed. 4.
To secure the base using the optional DIN Rail: Hardware Required • • • • DIN Rail, Qty. 1 3/16 in. dia x 5/8 in. long pan head screw, Qty. 2 1/2 in. OD x 7/32 in. ID x 3/64 in. thick washer, Qty. 2 3/16 in. dia nut, Qty. 2 1. Position the DIN Rail on the wall bracket, as shown below. 2. Slide the screw through the slot on the DIN Rail and the mounting hole in the bracket. 3. Slide the washer onto the screw and tighten the nut to secure the assembly. Wall Bracket, Qty. 1 Screw, Qty. 2 Washer, Qty.
Channel Bracket Installation (Pre-existing Hardware Installations) When choosing a location and installing the optional channel bracket: • Do not exceed 150 lbs. maximum load on the channel bracket. • Leave a minimum of 16 in. (40.64 cm) of horizontal space between the hardware used to attach the channel bracket to the wall. • An electrical outlet must be easily accessible. • The mounting location should be dry, stable, easily accessible, and well lighted. Tools Required • • • • • Drill 7/8 in.
2. Attach the channel bracket to a dry, stable surface using the hardware listed on page 15-8 for the appropriate mounting surface. Mounting into Wood Stud Washer, Qty. 4 Lag Bolt, Qty. 4 Channel Bracket Minimum 16 in. (40.64 cm) Mounting into Hollow Surface Washer, Qty. 4 Toggle Nut, Qty. 4 Toggle Bolt, Qty. 4 Channel Bracket Minimum 16 in. (40.64 cm) 3. Align the mounting holes on the wall bracket with the spring nuts installed in the channel bracket.
Removing Power to the ChargeBase ! 1. Attempting to remove the cable without disengaging the lock may result in damage to the base and power cable not covered by the warranty. Gently slide back the outer shell of the connector to disengage cable lock. Cable Lock Do not pull on the power connector cable or strain relief. 2. Remove the cable from the power jack.
16 Dolphin 99EX Net Base Device (Model 99EX-NB) Overview The Net Base enables up to four Dolphin 99EX or 99GX mobile computers to communicate with a host device over an Ethernet network. In addition, the Net Base provides a second RJ45 Ethernet port for connection to an additional device such as a printer, workstation, eBase, or another Net Base. The 99EX-NB charger is designed for use with battery pack models 99EX-BTSC (standard Li-poly 3.7 V, 11.3 watt hour) and 99EX-BTEC (extended Li-ion 3.7 V, 18.
Parts and Functions Front Panel Terminal Wells Power/Dock LED COMM LED Terminal Wells The Net Base contains four terminal wells. Each well has its own dedicated Power/Dock LED and COMM LED indicator. Place the Dolphin terminal in any one of the four wells to communicate with a host device, power the terminal, and charge the installed battery pack. The Net Base completely charges the main battery in a Dolphin terminal in 4 hours for the standard 3.7V battery or 6 hours for the extended 3.7 battery.
Back Panel Green LED Yellow LED Port 1: 10/100Mbps RJ45 Ethernet Port DC Power Jack Port 2: 100Mbps Only RJ45 Ethernet Port DC Power Jack Use the power cable from Honeywell that comes with the Net Base to supply power to this power jack. For more information, see Power on page 16-4. RJ45 Ethernet Ports The Net Base contains two RJ45 Ethernet ports.
Bottom Panel For details on how to mount the Net Base, see Mounting the Net Base on page 16-6. MAC Address Label Compliance Label Serial Number Label Power The terminal requires 12 Volts DC input for communications and battery charging; the power adapter on the power cable converts the voltage from the power source to 12 volts DC. Use only UL Listed power supply, which has been qualified by Honeywell with output rated at 12VDC and 8.5 amps with the device.
Charging the Main Battery The base provides power to the Dolphin terminals and allows the charging of the main batteries in the terminals. The main battery of each terminal charges in 4 hours for the standard 3.7V battery or 6 hours for the extended 3.7V battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which means that Dolphin terminals may be stored in the base indefinitely without damage to the terminals, battery packs, or the base.
3. Plug the Ethernet cable into the network. 4. Insert the Dolphin into one of the terminal wells. The DOCK LED for the well changes from red to green and the connection icon on the Dolphin’s title bar changes from x to . 5. By default, the DHCP server assigns a unique IP address to each of the Dolphin terminals docked in the Net Base. This IP address can be used by any application on the Dolphin terminal.
Desk Mounting The DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting on a horizontal surface. Hardware Required • 3/16 in. dia x 5/8 in. long pan head screw • 1/2 in. OD x 7/32 in. ID x 3/64 in. thick washer • 3/16 in. dia nut Installing the DIN Rail 1. Slide the DIN Rail into the DIN Rail slot on the bottom panel of the base. 2. Turn the base and DIN Rail right side up. 3. Then, using the appropriate hardware, secure the DIN Rail to a stable, flat horizontal surface. DIN Rail (7.
Hollow Wall Installation 1. Drill four pilot holes in the wall using a 7/8 in. drill bit. 13.78 in. [35 cm] 6.5 in. [16.5 cm] 2. 3. Wall Mount Bracket Wall Mount Holes Slide the bolt through the wall bracket, and thread the toggle nut onto the bolt. Press the ends of the toggle nut together, and insert the bolt/nut into the pilot hole until the nut clears inside wall surface. The toggle nut should spring open preventing the screw from being removed. 4.
To secure the base using the optional DIN Rail: Hardware Required • • • • DIN Rail, Qty. 1 3/16 in. dia x 5/8 in. long pan head screw, Qty. 2 1/2 in. OD x 7/32 in. ID x 3/64 in. thick washer, Qty. 2 3/16 in. dia nut, Qty. 2 1. Position the DIN Rail on the wall bracket, as shown below. 2. Slide the screw through the slot on the DIN Rail and the mounting hole in the bracket. 3. Slide the washer onto the screw and tighten the nut to secure the assembly. Wall Bracket, Qty. 1 Screw, Qty. 2 Washer, Qty.
Channel Bracket Installation (Pre-existing Hardware Installations) When choosing a location and installing the optional channel bracket: • Do not exceed 150 lbs. maximum load on the channel bracket. • Leave a minimum of 16 in. (40.64 cm) of horizontal space between the hardware used to attach the channel bracket to the wall. • An electrical outlet must be easily accessible. • The mounting location should be dry, stable, easily accessible, and well lighted. Tools Required • • • • • Drill 7/8 in.
2. Attach the channel bracket to a dry, stable surface using the hardware listed on page 16-10 for the appropriate mounting surface. Mounting into Wood Stud Washer, Qty. 4 Lag Bolt, Qty. 4 Channel Bracket Minimum 16 in. (40.64 cm) Mounting into Hollow Surface Washer, Qty. 4 Toggle Nut, Qty. 4 Toggle Bolt, Qty. 4 Channel Bracket Minimum 16 in. (40.64 cm) 3. Align the mounting holes on the wall bracket with the spring nuts installed in the channel bracket.
Removing Power to the Net Base ! 1. Attempting to remove the cable without disengaging the lock may result in damage to the base and power cable not covered by the warranty. Gently slide back the outer shell of the connector to disengage cable lock. Cable Lock Do not pull on the power connector cable or strain relief. 2. Remove the cable from the power jack.
17 Dolphin 99EX QuadCharger Device (Model 99EX-QC) Overview This 4-slot charging station provides intelligent battery management for the rechargeable battery packs used in Dolphin terminals. The 99EX-QC charger is designed for use with battery pack models 99EX-BTSC (standard Li-poly 3.7 V, 11.3 watt hour) and 99EX-BTEC (extended Li-ion 3.7 V, 18.5 watt hour) manufactured for Honeywell International Inc. Note: The QuadCharger is not designed for use in hazardous locations.
Parts and Functions Top Panel Charging Slots (4) Power LED Status LEDs One Per Charging Slot Charging Slots There are 4 charging slots. Each slot holds one Li-ion or Li-poly battery and charges it independently of the other slots. When a battery is placed in each slot, it immediately begins charging. Power LED The power LED indicates if the QuadCharger is powered and operational. When the QuadCharger is receiving power, the LED illuminates green.
Supplying Power The charger must be connected to a power source via the Honeywell power adapter cable so that voltage is adjusted appropriately. Use only UL Listed power supply, which has been qualified by Honeywell with output rated at 12VDC and 3 amps with the device. 1. Locate the AC power adapter cable and plug it into the power source. 2. Connect the power cable to the power adapter. 3. Connect the power cable to the supply connector on the back of the charger.
Mounting the QuadCharger The charger should be on a dry, stable surface and can be mounted on a flat, horizontal surface such as a desktop or workbench. When choosing a location, always bear in mind that: • the mounting location must allow users easy access to the power connector. • the charger should be oriented so that users can easily insert and remove battery packs and see the LEDs. Bottom Panel 3.94 in. [10 cm] DIN Rail Slot Rubber Feet, Qty.
Troubleshooting If you encounter problems with your QuadCharger device, refer to chart below for possible solutions. If problems persist, please contact Honeywell Technical Support. Problem Issue The Status LED does not come on when I insert a battery pack. Check the power connections; make sure the Power cable is inserted into the Power supply connector and the battery pack is properly seated. The Status LED lights red during charging. Try to charge the battery in one of the other charging slots.
17 - 6
18 Customer Support Product Service and Repair Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain warranty or non-warranty service, please visit www.honeywellaidc.com, and select Support > Contact Service and Repair to see your region’s instructions on how to obtain a Return Material Authorization number (RMA #). You should do this prior to returning the product.
HII. In the event that the product is returned to HII or its authorized service center within the Warranty Period and HII determines to its satisfaction that the product is defective due to defects in materials or workmanship, HII, at its sole option, will either repair or replace the product without charge, except for return shipping to HII.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.
