User's Manual

ManualsBrandsHoneywell International ManualsElectronicsBluetooth Charging Base

RS485:

Base LED Sequences and Meaning

Reading Techniques

The view finder projects an aiming

beam that should be centered over

the bar code, but it can be posi-

tioned in any direction for a good

read.

Hold the scanner over the bar code,

pull the trigger, and center the aim-

ing beam on the bar code.

The aiming beam is smaller when

the scanner is closer to the code and larger when it is farther from

the code. Hold the scanner close to smaller bar codes, and farther

away from large bar codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need to

tilt the scanner at an angle so the bar code can be scanned.

Note: If the scanner beeps 3 times when scanning a bar code, the

link has not been established. If the scanner beeps once, the

link has been established.

Xenon™ 1902G-BF

CCB01-010BT-BF

Battery-Free Wireless Area-Imaging Scanner and

Charge Base

Quick Start Guide

Aller à www.honeywellaidc.com pour le français.

Vai a www.honeywellaidc.com per l'italiano.

Gehe zu www.honeywellaidc.com für Deutsch.

Ir a www.honeywellaidc.com para español.

Para Português, acesse www.honeywellaidc.com.br.

Перейти на русскоязычный сайт www.honeywellaidc.com.

Pro češtinu jdi na www.honeywellaidc.com.

Pre slovenčinu choď na www.honeywellaidc.com

日本語 : www.honeywellaidc.com をご覧ください。

如要到中国

www.honeywellaidc.com

（简体）。

查看繁体版请登陆

www.honeywellaidc.com

한글 www.honeywellaidc.com 로 이동합니다 .

Rev (a)

11/16

Red LED - Host Communication

Red LED

Condition

Off

Power off, USB suspend

On continuously

Power on, system idle

Short blinks. Occurs while

transferring data to the host

port.

Receiving data

LED Indicators - Scanner Instant Charge Pack

Green LED

Yellow LED

Condition

On continuously

Battery has full charge

Slow blink

Battery less than 100%

capacity

Fast blink

Battery less than 50%

capacity

Fast blink

Under 50 scans available

Off

Scanner not in cradle

Note: Refer to your user’s guide for information about cleaning your

device.

Getting Started

Turn off the computer’s power before connecting the base, then

power up the computer once the base is fully connected. When the

base is connected and powered up, put the scanner in the base to

establish a link. The green LED on the base flashes to indicate the

scanner’s instant charge pack is charging. The scanner must be

returned to the base when not in use. A scanner charged on the

base with the power supply for 35 seconds will result in 100 scans,

with one scan every second.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

Connecting the Scanner

USB:

Note: If you are charging the scanner using the USB cable, the

current available for charging is reduced and charge times are

increased. Charging via the power supply is faster.

Keyboard Wedge:

RS232 Serial Port:

Summary of content (5 pages)

PAGE 1
Note: Refer to your user’s guide for information about cleaning your device. Connecting the Scanner Keyboard Wedge: USB: Getting Started Turn off the computer’s power before connecting the base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the scanner in the base to establish a link. The green LED on the base flashes to indicate the scanner’s instant charge pack is charging. The scanner must be returned to the base when not in use.
PAGE 2
Standard Product Defaults The following bar code resets all standard product default settings. COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically use a class driver. USB Serial Standard Product Defaults Note: No extra configuration (e.g., baud rate) is necessary. RS485 Interface The RS485 interface defaults to port 5B.
PAGE 3
Country Code Scan Country Code Scan Belgium Denmark Finland France Germany/Austria Great Britain 1 8 2 3 4 7 Italy Norway Spain Switzerland USA (Default) 5 9 10 6 0 Override Locked Scanner Temporary Streaming Presentation™ Mode If you need to replace a broken or lost scanner that is linked to a base, scan the Override Locked Scanner bar code with a new scanner, and place that scanner in the base.
PAGE 4
Preliminary Draft 11/30/16 Rev (c) FCC Part 15 Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment.
PAGE 5
Preliminary Draft 11/30/16 This document was prepared and executed in the English language. In the event this document is translated into another language and a conflict arises between the English version and a non-English version, the English version shall prevail, it being recognized and acknowledged that the English language version most clearly expresses the intent of the parties. Any notice or communication given in connection with this document must include a version in the English language.