Xenon™ XP 1952g/1952g-BF CCB01-010BT/CCB01-010BT-BF CCB-H-010BT/CCB-H-010BT-BF Cordless Area-Imaging Scanner and Charge Bases Quick Start Guide 1952-52BF-EN-QS-01 Rev (a)
Agency Model: 1952/1952-BF/ CCB-H-010BT/ CCB-H-010BT-BF Note: Refer to your User Guide for information about cleaning your device. Getting Started Turn off computer’s power before connecting the scanner, then power up the computer once the scanner is fully connected. When the base is connected and powered up, put the scanner in the base to establish a link. The green LED on the base flashes to indicate the scanner’s battery or charge pack is charging.
Connecting the Scanner USB: Note: If you are charging the scanner using the USB cable, the current available for charging is reduced and charge times are increased. Charging via the power supply is faster.
Keyboard Wedge: CCB01-010BT or CCB01-010BT-BF Base: CCB-H-010BT or CCB-H-010BT-BF Base: 3
RS232 Serial Port: CCB01-010BT or CCB01-010BT-BF Base: CCB-H-010BT or CCB-H-010BT-BF Base: 4
RS485: CCB01-010BT or CCB01-010BT-BF Base: CCB-H-010BT or CCB-H-010BT-BF Base: 5
Reading The view finder projects an aiming beam that Techniques should be centered over the bar code, but it can be positioned in any direction for a good read. Note: If the scanner beeps 3 times when scanning a bar code, the link has not been established. If the scanner beeps once, the link has been established. Standard Product Defaults The following bar code resets all standard product default settings.
RS485 The RS485 interface defaults to port 5B. If you have an IBM POS Interface terminal using port 9B, scan the appropriate code below to program the terminal, then power cycle the cash register. IBM Port 9B HHBCR-1 Interface IBM Port 9B HHBCR-2 Interface Note: For additional RS485 interface selections, see the User Guide for your product. USB Serial If you are using a Microsoft® Windows® PC, you must download a driver from the Honeywell website. The driver will use the next available COM Port number.
USB PC Scan the following code to program the scanner for a USB PC Keyboard Keyboard. USB PC Keyboard Keyboard Country Scan the appropriate country code below to program the keyboard layout for your country or language. By default, national character replacements are used for the following characters: #$@[\]^‘{|}~ Refer to the ISO 646 Character Replacements chart in your User Guide to view the character replacements for each country.
France Germany/Austria Great Britain Italy Norway Spain Switzerland Note: For a complete list of country codes, see the User Guide for your product.
Locked If you link a scanner to a base using the Locked Link Mode, Link other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into the base, it will charge the scanner, but the scanner will not be linked. Locked Link Mode (Single Scanner) To use a different scanner, you need to unlink the original scanner by scanning the Unlink Scanner bar code.
Unlinking the If the base has a scanner linked to it, that scanner must be Scanner unlinked before a new scanner can be linked. Once the previous scanner is unlinked, it will no longer communicate with the base. Scan the Unlink Scanner bar code to unlink a scanner. Unlink Scanner Trigge r The following bar codes will allow you to use the scanner in Manual Trigger - Normal Mode (need to press the trigger to read) or Presentation mode (the scanner is activated when it “sees” a bar code).
Streaming When in Streaming Presentation mode, the scanner leaves the Presentation™ scan illumination on all the time and continuously searches for bar codes. Streaming Presentation Mode Suffi x If you want a carriage return after the bar code, scan the Add CR Suffix bar code. To add a tab after the bar code, scan the Add Tab Suffix bar code. Otherwise, scan the Remove Suffix bar code to remove the suffixes.
Add Code ID Prefix to all Scan the following bar code if you wish to add a Code ID prefix to Symbologies all symbologies at once. Add Code ID Prefix To All Symbologies (Temporary) Note: For a complete list of Code IDs, see the User’Guide for your product. Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in your User Guide.
Charge Pack Status - Xenon XP 1952gBF The onlyfollowing charge status feedback is provided by a Xenon XP 1952fBF scanner when the scanner is out of the base and has been idle for 5 seconds.
Product Product documentation is available at www.honeywellaidc.com. Documentation Limited Warranty For warranty information, go to www.honeywellaidc.com and click Get Resources > Product Warranty. Patents For patent information, see www.hsmpats.com. Disclaimer Honeywell International Inc.
Copyright 2019 Honeywell International Inc. All rights reserved.
CCB-H-ML-RS-01 Rev (a) CCB-H-010BT and CCB-H-010BT-BF Charge/Communication Base Preliminary Draft 3/26/19 Agency Model: CCB-H-010BT, CCB-H-010BT-BF Product documentation is available at www.honeywellaidc.com. La documentation sur le produit est disponible à www.honeywellaidc.com. La documentation du produit est disponible sur le site www.honeywellaidc.com. La documentazione sul prodotto è disponibile sul sito www.honeywellaidc.com. Die Produktdokumentation ist unter www.honeywellaidc.com verfügbar.
Preliminary Draft 3/26/19 Obtenga información sobre la garantía en www.honeywellaidc.com y seleccione Get Resources (Obtener recursos) > Product Warranty (Garantía del producto.) Get Resources ( www.honeywellaidc.com ) > Product Warranty ( ) Informácie o záruke nájdete na www.honeywellaidc.com v časti Get Resources (Získať zdroje) > Product Warranty (Záruka výrobku). The following statements may not apply to products assembled in Mexico: Para obtener información sobre la garantía, visite el sitio www.