User's Manual

ManualsBrandsHoneywell International ManualsElectronicsWireless Smoke / Carbon Monoxide (CO) Detector

W4-IC Combination Smoke/

Carbon Monoxide (CO) Detector

with Built-in Wireless Transmitter

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6583

www.systemsensor.com

BEFORE INSTALLATION

Please read this manual thoroughly along with the Application Guides for Sys-

tem Sensor Smoke (A05-1003) and CO Detectors (A05-1099), which provide

detailed information on detector spacing, placement, zoning and special ap-

plications. Copies of these manuals are available at systemsensor.com.

IMPORTANT: This detector must be tested and maintained regularly following

NFPA 72/NFPA 720 requirements.

GENERAL DESCRIPTION

The W4 series is a battery-operated, system-connected, combination carbon

monoxide/smoke detector with a built-in wireless transmitter for use with

iControl wireless control panel models. It will report maintenance, tamper and

independent smoke alarm or CO alarm signals to a compatible wireless con-

trol panel. It has a speaker for vocal feedback, multi-criteria smoke detection,

and integrated side LED windows that are viewable from 360 degrees when

the detector is in an alarm condition.

FEATURES

Smoke Features

• Multi-criteria smoke sensing using a combination of photoelectric, heat,

flame flicker and carbon monoxide sensing.

• Drift compensation and noise rejection algorithms.

• Smoke test button.

• 360 degree, side viewable red LED smoke indication.

CO Features

• 10 year electrochemical CO sensor.

• Sensor end-of-life notification.

• CO test button.

• RealTest® functional gas entry test capable.

• 360 degree, side viewable blue LED CO indication.

Audible Annunciation

• Local integral sounder.

• Voice speaker provides supplemental instructions during alarm, installa

tion and maintenance feedback.

Installation and Maintenance

• Universal mounting base.

• Audible maintenance information including smoke sensitivity.

Other Features

• Ships with 4 CR-123 lithium batteries.

• UL/ULC listed to standards 268 and 2075.

SPECIFICATIONS

Electrical Specifications

Voltage: 3 volts DC

Battery Type: CR-123 lithium

Battery Manufacturer: Duracell DL123A or Panasonic CR123A

Use of a different battery may have a detrimental effect on device operation

Number of Batteries: 4

Sensitivity 0.9 to 2.64/ft. (.27 to .80/m)

Audible Signal: 85dBA

Physical Specifications

Diameter: 5.95 inches (15.113 cm)

Height: 2.03 inches (5.1562cm)

Weight: 13.92oz (383 g)

Operating Temperature Range: 0 - 38° C (32 - 100°F)

Storage Temperature Range: -10 - 70° C (14 - 158° F)

Operating Humidity Range: 20-95% RH

This product is compatible with iControl Technicolor TCA203 control panels

*NFPA requires a UL listed sounder on the NAC circuit.

Notice: This manual shall be left with the owner/user of this equipment.

I56-5942-000

VISIBLE ANNUNCIATON

The W4 series detector has a multi-color top LED; Green, Red, and Amber.

The LED is green for supervisory indication; it blinks during power on, reset,

and during normal operation. The LED is amber to signal maintenance and

trouble events. W4 utilizes the side LED windows to indicate alarm events;

red for smoke and blue for CO.

INSTALLATION GUIDELINES

Ceiling: Detector should be at least 12 inches (30 cm) from any wall.

Wall: Detector should be no closer than 6 inches (15 cm) from ceiling.

• Do not install outdoors or in any environment that does not comply with

the detector’s environmental specifications.

• Install in accordance with NFPA 72 and 720 standards.

NFPA 72 and

720 define standards for both commercial and residential installation of

smoke and CO detectors. Local laws involving CO detection should also

be considered.

• If the installation can be interpreted as residential, consult the section

of NFPA 720 that outlines residential applications.

Chapter 9.4.1.1, for

example, states that carbon monoxide alarms or detectors shall be in-

stalled as follows:

• Outside each separate dwelling unit sleeping area in the immediate

vicinity of the bedroom.

• On every level of a dwelling unit, including basements.

• Consult NFPA 72, the local Authority Having Jurisdiction (AHJ), and/

or applicable codes for specific information regarding the spacing and

placement of smoke detectors.

FIGURE 1: ALARM LOCATION DIAGRAM FOR RESIDENTIAL APPLICATION

LIVING

ROOM

BEDROOM BEDROOM

BEDROOM

KITCHEN

CLOSED

DOOR

BASEMENT

GARAGE

CARBON MONOXIDE/SMOKE ALARM

LOCATION FOR MULTI-LEVEL RESIDENCE

–

S0295-01

Global 2.4 Ghz wireless use

ZigBee® Certified is a registered

trademark of the Zigbee Alliance.

1 I56-5942-000

09-14

Summary of content (4 pages)

PAGE 1
W4-IC Combination Smoke/ Carbon Monoxide (CO) Detector with Built-in Wireless Transmitter SPECIFICATIONS Electrical Specifications Voltage: Battery Type: Battery Manufacturer: 3825 Ohio Avenue, St. Charles, Illinois 60174 1-800-SENSOR2, FAX: 630-377-6583 www.systemsensor.com 3 volts DC CR-123 lithium Duracell DL123A or Panasonic CR123A Use of a different battery may have a detrimental effect on device operation 4 0.9 to 2.64/ft. (.27 to .
PAGE 2
• Do not install detectors in the following areas: • In or near areas where particles of combustion are normally present such as kitchens, in garages, near furnaces, hot water heaters, or gas space heaters. • In very cold or very hot areas that may be outside the detectors operating range. • In wet or excessively humid areas, or next to bathrooms with showers. • In dusty, dirty, or insect-infested areas. • Near fresh air inlets or returns or excessively drafty areas.
PAGE 3
FIGURE 2: TEST BUTTON LOCATION AND OPERATION FIGURE 3: CO GAS ENTRY LOCATION CO S0338-00 SMOKE ENTRY TEST / SMOKE SENSITIVITY READOUT To smoke test W4, because it is a multi-criteria detector), it must be put into the smoke test mode as follows: S0339-00 1. With the detector in standby mode, press and hold the smoke test button for 3 to 5 seconds. The W4 will provide diagnostic information including sensor status and smoke sensitivity reading and will prompt for smoke entry and annunciate per Table 2.
PAGE 4
CO WARNING 4. Test the detector to insure it is fully functional. (See Testing section.) 5. Notify the proper authorities when the system is back in service. Do not paint, and do not use cleaning agents, bleach or polish the detector. WARNING WARNING: Carbon Monoxide is an odorless, colorless, tasteless gas when unit is in alarm move to fresh air immediately.