User's Guide
Table Of Contents
- Voyager™ 1200g/1202g/1202g-BF User’s Guide
- Table of Contents
- Getting Started
- Programming the Interface
- Introduction
- Programming the Interface - Plug and Play
- USB Serial Commands
- Verifone® Ruby Terminal Default Settings
- Gilbarco® Terminal Default Settings
- Honeywell Bioptic Aux Port Configuration
- Datalogic™ Magellan© Bioptic Aux Port Configuration
- NCR Bioptic Aux Port Configuration
- Wincor Nixdorf Terminal Default Settings
- Wincor Nixdorf Beetle™ Terminal Default Settings
- Wincor Nixdorf RS232 Mode A
- Keyboard Country Layout
- Keyboard Wedge Modifiers
- RS232 Modifiers
- NCR Modifiers
- Scanner to Bioptic Communication
- Cordless System Operation (Voyager 1202g)
- How the Charge and Communications Base Works
- Linking the Scanner to a Base
- Communication Between the Cordless System and the Host
- RF (Radio Frequency) Module Operation
- System Conditions
- Page Button
- About the Battery
- Voyager 1202g Battery Removal
- Flash Updates
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanning While in Base Cradle
- Base Charging Modes
- Paging
- Scanner Address
- Base Address
- Scanner Modes
- Unlinking the Scanner
- Override Locked Scanner
- Out-of-Range Alarm
- Scanner Power Time-Out Timer
- RangeGate
- Batch Mode
- Scanner Name
- Using the Scanner with Bluetooth Devices
- Minimizing Bluetooth/ISM Band Network Activity
- Reset Scanner and Base
- Cordless System Operation (Voyager 1202g-BF)
- How the Charge and Communications Base Works
- Linking the Scanner to a Base
- Communication Between the Cordless System and the Host
- RF (Radio Frequency) Module Operation
- System Conditions
- About the Instant Charge Pack
- Flash Updates
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanning While in Base Cradle
- Paging
- Scanner Address
- Base Address
- Scanner Modes
- Unlinking the Scanner
- Override Locked Scanner
- Out-of-Range Alarm
- Using the Scanner with Bluetooth Devices
- Minimizing Bluetooth/ISM Band Network Activity
- Reset Scanner and Base
- Input/Output Settings
- Data Editing
- Data Formatting
- Symbologies
- All Symbologies
- Message Length Description
- Codabar
- Code 39
- Interleaved 2 of 5
- NEC 2 of 5
- Code 93
- Straight 2 of 5 Industrial (three-bar start/stop)
- Straight 2 of 5 IATA (two-bar start/stop)
- Matrix 2 of 5
- Code 11
- Code 128
- GS1-128
- Telepen
- UPC-A
- UPC-A/EAN-13 with Extended Coupon Code
- UPC-E0
- EAN/JAN-13
- EAN/JAN-8
- MSI
- Plessey Code
- GS1 DataBar Omnidirectional
- GS1 DataBar Limited
- GS1 DataBar Expanded
- Trioptic Code
- GS1 Emulation
- Postal Codes
- Utilities
- Serial Programming Commands
- Product Specifications
- Maintenance and Troubleshooting
- Reference Charts
10 - 12
Scanner Modes Charge Only Mode :*:BASLNK0 4-6
*Charge and Link Mode :*:BASLNK1 4-6
Locked Link Mode :*:BASCON0 4-7
*Open Link Mode :*:BASCON1 4-7
Unlink Scanner BT_RMV 4-7
Override Locked Scanner BT_RPL1 4-7
Out-of-Range Alarm Scanner Alarm Type BT_ORW 4-8
Scanner Alarm Duration (Range 1 - 3000
sec (*1))
BT_ORD 4-8
Auto Reconnect Mode *Auto Reconnect On BT_ACM1 4-8
Auto Reconnect Off BT_ACM0 4-8
Maximum Link Attempts Maximum Link Attempts
Range 0-255 (*0)
BT_MLA### 4-9
Reset Reset Base RESET_ 4-10
Reset Scanner :*:RESET_ 4-10
Input/Output Selections
Power Up Beeper Power Up Beeper Off - Scanner BEPPWR0 5-1
*Power Up Beeper On - Scanner BEPPWR1 5-1
Beep on BEL Character Beep on BEL On BELBEP1 5-1
*Beep on BEL Off BELBEP0 5-1
Beeper - Good Read Off BEPBEP0 5-1
*On BEPBEP1 5-1
Beeper Volume - Good Read Off BEPLVL0 5-1
Low BEPLVL1 5-2
Medium BEPLVL2 5-2
*High BEPLVL3 5-2
Beeper Pitch - Good Read
(Frequency)
Low (1600 Hz) BEPFQ11600 5-2
*Medium (2350 Hz) BEPFQ12350 5-2
High (4200 Hz) BEPFQ14200 5-2
Beeper - Transmit Order Before Transmission BEPWHN1 5-2
After Transmission BEPWHN2 5-2
Beeper Pitch - Error (Frequency) *Razz (100 Hz) BEPFQ2100 5-3
Medium (2000 Hz) BEPFQ22000 5-3
High (4200 Hz) BEPFQ24200 5-3
Beeper Duration - Good Read *Normal Beep BEPBIP0 5-3
Short Beep BEPBIP1 5-3
Number of Beeps - Good Read Range 1 - 9 (*1) BEPRPT# 5-3
Number of Beeps - Error Range 1 - 9 (*1) BEPERR# 5-4
Selection
Setting
* Indicates default
Serial Command
# Indicates a numeric entry
Page