User's Guide
Table Of Contents
- Voyager™ 1200g/1202g/1202g-BF User’s Guide
- Table of Contents
- Getting Started
- Programming the Interface
- Introduction
- Programming the Interface - Plug and Play
- USB Serial Commands
- Verifone® Ruby Terminal Default Settings
- Gilbarco® Terminal Default Settings
- Honeywell Bioptic Aux Port Configuration
- Datalogic™ Magellan© Bioptic Aux Port Configuration
- NCR Bioptic Aux Port Configuration
- Wincor Nixdorf Terminal Default Settings
- Wincor Nixdorf Beetle™ Terminal Default Settings
- Wincor Nixdorf RS232 Mode A
- Keyboard Country Layout
- Keyboard Wedge Modifiers
- RS232 Modifiers
- NCR Modifiers
- Scanner to Bioptic Communication
- Cordless System Operation (Voyager 1202g)
- How the Charge and Communications Base Works
- Linking the Scanner to a Base
- Communication Between the Cordless System and the Host
- RF (Radio Frequency) Module Operation
- System Conditions
- Page Button
- About the Battery
- Voyager 1202g Battery Removal
- Flash Updates
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanning While in Base Cradle
- Base Charging Modes
- Paging
- Scanner Address
- Base Address
- Scanner Modes
- Unlinking the Scanner
- Override Locked Scanner
- Out-of-Range Alarm
- Scanner Power Time-Out Timer
- RangeGate
- Batch Mode
- Scanner Name
- Using the Scanner with Bluetooth Devices
- Minimizing Bluetooth/ISM Band Network Activity
- Reset Scanner and Base
- Cordless System Operation (Voyager 1202g-BF)
- How the Charge and Communications Base Works
- Linking the Scanner to a Base
- Communication Between the Cordless System and the Host
- RF (Radio Frequency) Module Operation
- System Conditions
- About the Instant Charge Pack
- Flash Updates
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanning While in Base Cradle
- Paging
- Scanner Address
- Base Address
- Scanner Modes
- Unlinking the Scanner
- Override Locked Scanner
- Out-of-Range Alarm
- Using the Scanner with Bluetooth Devices
- Minimizing Bluetooth/ISM Band Network Activity
- Reset Scanner and Base
- Input/Output Settings
- Data Editing
- Data Formatting
- Symbologies
- All Symbologies
- Message Length Description
- Codabar
- Code 39
- Interleaved 2 of 5
- NEC 2 of 5
- Code 93
- Straight 2 of 5 Industrial (three-bar start/stop)
- Straight 2 of 5 IATA (two-bar start/stop)
- Matrix 2 of 5
- Code 11
- Code 128
- GS1-128
- Telepen
- UPC-A
- UPC-A/EAN-13 with Extended Coupon Code
- UPC-E0
- EAN/JAN-13
- EAN/JAN-8
- MSI
- Plessey Code
- GS1 DataBar Omnidirectional
- GS1 DataBar Limited
- GS1 DataBar Expanded
- Trioptic Code
- GS1 Emulation
- Postal Codes
- Utilities
- Serial Programming Commands
- Product Specifications
- Maintenance and Troubleshooting
- Reference Charts
10 - 16
Data Formatter Selections
Data Format Editor *Default Data Format (None) DFMDF3 7-1
Enter Data Format DFMBK3## 7-2
Clear One Data Format DFMCL3 7-2
Clear All Data Formats DFMCA3 7-2
Data Formatter Data Formatter Off DFM_EN0 7-10
*Data Formatter On,
Not Required,
Keep Prefix/Suffix
DFM_EN1 7-10
Data Format Required,
Keep Prefix/Suffix
DFM_EN2 7-11
Data Formatter On,
Not Required,
Drop Prefix/Suffix
DFM_EN3 7-10
Data Format Required,
Drop Prefix/Suffix
DFM_EN4 7-11
Data Format Non-Match Error Tone *Data Format Non-Match Error Tone On DFMDEC0 7-11
Data Format Non-Match Error Tone Off DFMDEC1 7-11
Primary/Alternate Data Formats Primary Data Format ALTFNM0 7-11
Data Format 1 ALTFNM1 7-11
Data Format 2 ALTFNM2 7-11
Data Format 3 ALTFNM3 7-11
Single Scan Data Format Change Single Scan-Primary
Data Format
VSAF_0 7-12
Single Scan-Data Format 1 VSAF_1 7-12
Single Scan-Data Format 2 VSAF_2 7-12
Single Scan-Data Format 3 VSAF_3 7-12
Symbologies
All Symbologies All Symbologies Off ALLENA0 8-1
All Symbologies On ALLENA1 8-1
Codabar Default All Codabar
Settings
CBRDFT 8-2
Off CBRENA0 8-2
*On CBRENA1 8-2
Codabar Start/Stop Char. *Don’t Transmit CBRSSX0 8-2
Transmit CBRSSX1 8-2
Codabar Check Char. *No Check Char. CBRCK20 8-2
Validate Modulo 16, But Don’t Transmit CBRCK21 8-2
Validate Modulo 16, and Transmit CBRCK22 8-3
Validate Modulo 7 CD, But Don’t Transmit CBRCK23 8-3
Validate Modulo 7 CD, and Transmit CBRCK24 8-3
Validate CLSI, But Don’t Transmit CBRCK25 8-3
Validate CLSI, and Transmit CBRCK26 8-3
Selection
Setting
* Indicates default
Serial Command
# Indicates a numeric entry
Page