User's Guide
Table Of Contents
- Voyager™ 1200g/1202g/1202g-BF User’s Guide
- Table of Contents
- Getting Started
- Programming the Interface
- Introduction
- Programming the Interface - Plug and Play
- USB Serial Commands
- Verifone® Ruby Terminal Default Settings
- Gilbarco® Terminal Default Settings
- Honeywell Bioptic Aux Port Configuration
- Datalogic™ Magellan© Bioptic Aux Port Configuration
- NCR Bioptic Aux Port Configuration
- Wincor Nixdorf Terminal Default Settings
- Wincor Nixdorf Beetle™ Terminal Default Settings
- Wincor Nixdorf RS232 Mode A
- Keyboard Country Layout
- Keyboard Wedge Modifiers
- RS232 Modifiers
- NCR Modifiers
- Scanner to Bioptic Communication
- Cordless System Operation (Voyager 1202g)
- How the Charge and Communications Base Works
- Linking the Scanner to a Base
- Communication Between the Cordless System and the Host
- RF (Radio Frequency) Module Operation
- System Conditions
- Page Button
- About the Battery
- Voyager 1202g Battery Removal
- Flash Updates
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanning While in Base Cradle
- Base Charging Modes
- Paging
- Scanner Address
- Base Address
- Scanner Modes
- Unlinking the Scanner
- Override Locked Scanner
- Out-of-Range Alarm
- Scanner Power Time-Out Timer
- RangeGate
- Batch Mode
- Scanner Name
- Using the Scanner with Bluetooth Devices
- Minimizing Bluetooth/ISM Band Network Activity
- Reset Scanner and Base
- Cordless System Operation (Voyager 1202g-BF)
- How the Charge and Communications Base Works
- Linking the Scanner to a Base
- Communication Between the Cordless System and the Host
- RF (Radio Frequency) Module Operation
- System Conditions
- About the Instant Charge Pack
- Flash Updates
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanning While in Base Cradle
- Paging
- Scanner Address
- Base Address
- Scanner Modes
- Unlinking the Scanner
- Override Locked Scanner
- Out-of-Range Alarm
- Using the Scanner with Bluetooth Devices
- Minimizing Bluetooth/ISM Band Network Activity
- Reset Scanner and Base
- Input/Output Settings
- Data Editing
- Data Formatting
- Symbologies
- All Symbologies
- Message Length Description
- Codabar
- Code 39
- Interleaved 2 of 5
- NEC 2 of 5
- Code 93
- Straight 2 of 5 Industrial (three-bar start/stop)
- Straight 2 of 5 IATA (two-bar start/stop)
- Matrix 2 of 5
- Code 11
- Code 128
- GS1-128
- Telepen
- UPC-A
- UPC-A/EAN-13 with Extended Coupon Code
- UPC-E0
- EAN/JAN-13
- EAN/JAN-8
- MSI
- Plessey Code
- GS1 DataBar Omnidirectional
- GS1 DataBar Limited
- GS1 DataBar Expanded
- Trioptic Code
- GS1 Emulation
- Postal Codes
- Utilities
- Serial Programming Commands
- Product Specifications
- Maintenance and Troubleshooting
- Reference Charts
10 - 20
ISBT 128 User-Defined Concatenation
Sequences On/Off
*Off ISBUCE0 8-21
Allow User-Defined Sequence ISBUCE1 8-21
Require User-Defined Sequence ISBUCE2 8-21
Content Verification *Off ISBXM00 8-21
On ISBXM01 8-21
Transmit Identifiers Off ISBXM10 8-22
*On ISBXM11 8-22
Flag Conversion *Off ISBXM20 8-22
On ISBXM21 8-22
GS1-128 Default All GS1-128 Settings GS1DFT 8-23
*On GS1ENA1 8-23
Off GS1ENA0 8-23
GS1-128 Application Identifier Parsing *Off GS1EMU0 8-23
Transmit Without Identifiers GS1EMU1 8-23
Transmit With Identifiers GS1EMU2 8-23
GS1-128 Redundancy Range (0 - 10) *0 GS1VOT## 8-23
GS1-128 Message Length Minimum (1 - 80) *3 GS1MIN 8-24
Maximum (0 - 80) *80 GS1MAX 8-24
Telepen Default All Telepen
Settings
TELDFT 8-24
*Off TELENA0 8-24
On TELENA1 8-24
Telepen Output *AIM Telepen Output TELOLD0 8-24
Original Telepen Output TELOLD1 8-24
Telepen Redundancy Range (0 - 10) *0 TELVOT## 8-25
Telepen Message Length Minimum (1 - 80) *3 TELMIN## 8-25
Maximum (1 - 80) *80 TELMAX## 8-25
UPC-A Default All
UPC-A Settings
UPADFT 8-25
Off UPBENA0 8-25
*On UPBENA1 8-25
UPC-A Number System Off UPANSX0 8-26
*On UPANSX1 8-26
UPC-A Check Digit Off UPACKX0 8-26
*On UPACKX1 8-26
UPC-A 2 Digit Addenda *Off UPAAD20 8-26
On UPAAD21 8-26
UPC-A 5 Digit Addenda *Off UPAAD50 8-27
On UPAAD51 8-26
UPC-A Addenda Required *Not Required UPAARQ0 8-27
Required UPAARQ1 8-27
Addenda Timeout Range (0 - 65535) *100 DLYADD##### 8-27
Selection
Setting
* Indicates default
Serial Command
# Indicates a numeric entry
Page