Voyager 1602g Wireless Area-Imaging Pocket Scanner VG1602-UG C Released Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC Honeywell proprietary & Confidential HEC: EAR99 TEC: EAR99 GOV: ESO1.0 User’s Guide The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Table of Contents Customer Support Technical Assistance ............................................................................................................ ix Product Service and Repair .................................................................................................. ix Limited Warranty ................................................................................................................... ix Send Feedback .................................................................
Programming the VG1602 Corded Interface ..................................................................... 2-23 Setting the VG1602 Corded Interface.......................................................................... 2-23 Corded USB PC or Macintosh Keyboard..................................................................... 2-23 Corded USB HID POS................................................................................................. 2-23 Corded USB Serial .................................
Resetting the Factory Defaults: All Application Work Groups ........................................... 3-13 Resetting the Custom Defaults: All Application Work Groups ........................................... 3-13 Access Point Operations ................................................................................................... 3-13 Linking the Scanner to an Access Point ......................................................................
Poor Quality Codes ............................................................................................................. 4-8 Poor Quality 1D Codes .................................................................................................. 4-8 Poor Quality PDF Codes ............................................................................................... 4-9 CodeGate® .........................................................................................................................
Chapter 6 - Data Formatting Data Format Editor Introduction .......................................................................................... 6-1 Add a Data Format .............................................................................................................. 6-1 Other Programming Selections...................................................................................... 6-2 Terminal ID Table .......................................................................................
GS1 DataBar Limited......................................................................................................... 7-31 GS1 DataBar Expanded .................................................................................................... 7-32 Trioptic Code ..................................................................................................................... 7-32 Codablock A ..........................................................................................................
Resetting the Custom Defaults............................................................................................ 9-3 Menu Commands ................................................................................................................ 9-4 Chapter 10 - Product Specifications Voyager 1602g Wireless Pocket Scanner Product Specifications .................................... 10-1 Standard Connector Pinout .........................................................................................
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released HEC: EAR99 Honeywell proprietary & Confidential Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC viii TEC: EAR99 GOV: ESO1.
Customer Support Technical Assistance To search our knowledge base for a solution or to log in to the Technical Support portal and report a problem, go to www.hsmcontactsupport.com. For our latest contact information, see www.honeywellaidc.com/locations. Product Service and Repair Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain warranty or non-warranty service, please visit www.honeywellaidc.
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released HEC: EAR99 Honeywell proprietary & Confidential Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC x TEC: EAR99 GOV: ESO1.
1 Getting Started About This Manual This User’s Guide provides installation and programming instructions for the Voyager 1602g scanners. Product specifications, dimensions, warranty, and customer support information are also included. Note: The selections in this User’s Guide are dependent on the Voyager 1602g model you have purchased. PDF and 2 dimensional bar codes can only be read by model 1602g2D and cannot be read by model 1602g1D.
Charging with a PC Charging your scanner battery through the USB port of a computer will take longer than charging with an electrical outlet. Connect the mini-USB connector to the scanner and the USB connector to the computer, as shown below. Note: The mini-USB connector is only used for charging the scanner. If using a scanner in corded mode, it can also be used to configure the device via EZConfig (see page 8-3 for further information).
Pairing the Scanner with Bluetooth® Devices The scanner can be paired with Bluetooth devices such as personal computers, laptops, tablets, and Apple® devices. 1. Scan the appropriate Bluetooth Connect bar code below to establish one-way communication with the Voyager 1602g.
4 5 6 7 8 9 Save Your personal computer, laptop, tablet, or Apple device should now be paired with the scanner. Once the scanner battery is charged and you have paired it, you may begin scanning bar codes. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. C Released Once the Apple device is connected to the Voyager 1602g using SPP, you must select the app that will be used to send commands to and receive responses from the scanner.
Reading Techniques The Voyager 1602g has a large scan button just forward of a smaller, programmable button. (See Programmable Button on page 4-1 for further information about the programmable button.) Scan button Press the scan button to project an aiming beam. This beam should be centered over the bar code, but it can be positioned in any direction for a good read.
Setting Custom Defaults You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults bar code below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code.
2 Programming the Interface Introduction This chapter describes how to program your scanner for different keyboards and settings, and for an interface when using an Access Point (see Programming an Interface for an Access Point, beginning on page 2-12). The VG1602g is primarily designed as a cordless scanner. However, if you are using the VG1602g as a corded scanner, see Programming the VG1602 Corded Interface beginning on page 2-23.
Keyboard Countries (Continued) Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia GOV: ESO1.0 Czech C Released Czech (QWERTZ) Honeywell proprietary & Confidential Czech (QWERTY) 2-2 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Keyboard Countries (Continued) Denmark Dutch (Netherlands) Estonia Faroese Finland France Gaelic GOV: ESO1.0 Germany Honeywell proprietary & Confidential Greek (220 Latin) Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC C Released Greek (220) 2-3 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Keyboard Countries (Continued) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) GOV: ESO1.0 Hungary C Released Italian (142) Honeywell proprietary & Confidential Irish 2-4 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Keyboard Countries (Continued) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) GOV: ESO1.0 Lithuania Honeywell proprietary & Confidential Macedonia Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC C Released Malta 2-5 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Keyboard Countries (Continued) Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania GOV: ESO1.0 Russia C Released SCS Honeywell proprietary & Confidential Russian (Typewriter) 2-6 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Keyboard Countries (Continued) Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain GOV: ESO1.0 Spanish variation 2-7 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Keyboard Countries (Continued) Tatar Turkey F Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) Keyboard Style C Released This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Keyboard Style settings. Default = Regular. 2-8 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off . This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).
Default = Keyboard Conversion Off. * Keyboard Conversion Off Convert All Characters to Upper Case Convert All Characters to Lower Case Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page 1252) on page A-3. Only codes 00 through 1F are converted (the first column of the chart).
* Control + X Mode Off DOS Mode Control + X Mode On Windows Mode Prefix/Suffix Off Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode. Default = Off. Turbo Mode On * Turbo Mode Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off. Numeric Keypad Mode On Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters.
Programming an Interface for an Access Point If you are using a Honeywell Access Point (AP01-XXXBT) to communicate with the VG1602, you can use the following bar codes to program the Access Point interface. These bar codes set the Access Point for commonly used interfaces. Keyboard Wedge If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below, then power cycle the host. Keyboard wedge is the default interface.
RS485 Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface. This interface is only appropriate for an Access Point. Note: After scanning one of these codes, you must power cycle the cash register.
RS485 Packet Length If you are using Packet mode, you can specify the size of the data “packet” that is sent to the host. Scan the Packet Length bar code, then then the packet size (from 20 - 256) from the Programming Chart inside the back cover of this manual, then Save. Default = 40. Packet Length USB IBM SurePos Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface.
USB HID Scan the following code to program the scanner for USB HID bar code scanners, then power cycle the host. This interface is only appropriate for an Access Point. USB HID Bar Code Scanner USB Serial This interface is only appropriate for an Access Point. Scan the following code to program the scanner to emulate a regular RS232-based COM Port, then power cycle the host. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com).
ReM On Gilbarco® Terminal Default Settings This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a Gilbarco terminal, then power cycle the host. This bar code sets the baud rate to 2400 bps and the data format to 7 data bits, even parity, 2 stop bits.
NCR Bioptic Aux Port Configuration This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration, then power cycle the host.
Wincor Nixdorf RS232 Mode A This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal, then power cycle the host. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit.
38400 57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity.
* 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A scan button push or serial trigger command resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out. A transaction on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds to completely come up.
* RTS/CTS Off RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 15100 milliseconds) by scanning digits from the inside back cover, then scanning Save. RS232 Timeout XON/XOFF Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending data (XON/XOFF Off).
Scanner to Bioptic Communication The following Scanner to Bioptic Communication settings should only be used when connecting through an Access Point. They are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner. See "RS232 Modifiers" on page 2-18, and RS232 Timeout on page 2-21 for further information.
Programming the VG1602 Corded Interface You may convert a VG1602 scanner to a corded scanner using a USB interface cable. Use the following bar codes to program the VG1602g as a corded scanner. Setting the VG1602 Corded Interface Scan one of the following codes to set the scanner’s communication as either Bluetooth, for a cordless scanner, to USB, for a corded scanner. Default = Bluetooth Communication (Cordless Scanner).
Corded USB Serial Scan the following code to program the corded scanner to emulate a regular RS232-based COM Port, then power cycle the host. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically use a class driver. Corded USB Serial Note: No extra configuration (e.g.
3 Wireless System Operation The VG1602g scanner can be used with Bluetooth devices such as personal computers, laptops, PDAs, and Honeywell mobility systems devices. Bluetooth Settings Refer to Pairing the Scanner with Bluetooth® Devices, beginning on page 1-3, to link your scanner to a host via Bluetooth. The following settings allow you to refine your Bluetooth connection.
Minimizing Bluetooth/ISM Band Network Activity The settings described below can help you customize the relinking behavior of the wireless area-imaging system to obtain the best compromise between convenience and low interference. Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth. Auto Reconnect Mode Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is detected.
Scan the Maximum Link Attempts bar code, then scan the number of attempts for the setting (from 0-100) from the inside back cover. Scan Save to save the setting. Default = 0. Maximum Link Attempts Note: When Auto Reconnect Mode is On, setting Maximum Link Attempts to zero will cause the scanner to try to link until the Power Time-Out Timer setting (see page 3-9) expires.
The scanner attempts to connect to the host every 15 seconds, measured from one attempt start to the next attempt start. After one half hour, the scanner powers off. Communication Between the Scanner and the Host When data is scanned, the data is sent to the host system. The wireless scanner provides immediate feedback in the form of a “good read” indication with a green LED on the scanner and an audible beep. This indicates only that the bar code has been scanned correctly.
Power is supplied to the wireless scanner by a rechargeable battery that is integrated in the scanner. Batteries are not shipped fully charged. The battery should be charged for a minimum of 4 hours before initial use to ensure optimal performance. Charging Information The battery is designed to charge while the scanner is plugged into a wall outlet or into a host via the USB cable. Refer to Low Battery Indicator, page 3-6, for an interpretation of the Charge Status indicators.
Scan LED Sequences and Meaning LED Indication Beeper Indication Cause Normal Operation Red flash Green flash Red, blinking Blue, off None 1 beep Razz or error tone None Blue flash None Blue, on Menu Operation Green flash Red, blinking 1 beep Battery low Successful scan Failed communication Bluetooth connection has not been established Scanner is attempting to pair with Bluetooth device Successful Bluetooth pairing 2 beeps Razz or error tone Successful menu change Unsuccessful menu change Low Bat
Scanner Address Scan the bar code below to determine the address of the scanner you are using. Scanner Address Linked Modes Locked Link Mode and Open Link Mode are the link modes that accommodate different applications. Scan the appropriate bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another. Default = Open Link Mode.
Override Locked Scanner If you need to replace a broken or lost scanner that is linked to a host, scan the Override Locked Scanner bar code below with a new scanner and pair that scanner with the host. The locked link will be overridden; the broken or lost scanner’s link with the host will be removed, and the new scanner will be linked. Override Locked Scanner (Single Scanner) Out-of-Range Alarm Note: This feature is only supported by a Honeywell Access Point (AP).
Scanner Idle Alarm When the scanner is idle for over 1 hour, you can set it to beep every minute until the trigger is pressed. Default = Scanner Idle Alarm Off. Scanner Idle Alarm On * Scanner Idle Alarm Off Scanner Power Time-Out Timer When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner power time-out bar code to change the time-out duration (in seconds). Note: Scanning zero (0) is the equivalent of setting no time-out.
Note: When the scanner is in power down mode, press the scan button to power the unit back up. There will be a set of power up beeps and a delay of up to a few seconds for the radio to join. The scanner will then be ready to use. Flexible Power Management If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn down the power output of the scanner.
The default name is in the format “ScannerName_Model_SN_XXXXXXXXXX” If you have more than one scanner linked to a host and they all have the same name, the first scanner linked to the host receives commands. When renaming a series of scanners with identical names, unlink all except one of the scanners from the host. Perform the rename operation using either the bar codes on page 3-11, or by sending the serial command :ScannerName:BT_NAMNewName.
Application Work Groups Note: Application Work Groups can only be used with an Access Point. Your wireless system can have up to 7 scanners linked to one host. You can also have up to 7 work groups. If you want to have all of the scanners’ settings programmed alike, you don’t need to use more than one work group. If you want each scanner to have unique settings (e.g.
Resetting the Factory Defaults: All Application Work Groups The following bar code defaults all of the work groups to the factory default settings. PAPDFT& Factory Default Settings: All Work Groups To see what the factory default settings are, refer to the table of Menu Commands, beginning on page 9-4. The standard product default settings for each of the commands are indicated by an asterisk (*).
Scan the linking bar code on the top of the Access Point to establish a connection between the Access Point and the scanner. The scanner emits a short beep and flashes the green LED to confirm a connection with the Access Point. The Access Point’s Page button remains blue. If the Access Point sounds 5 error tones followed by 3 beeps, it indicates that you are attempting to link to the incorrect model Access Point. The Voyager 1602g scanner can only link to an Access Point model AP01-010BT or AP01-100BT.
Access Point LED Sequences and Meaning The Access Point has a blue LED on the top of the unit that indicates its power up and communication condition. Blue LED - Host Communication Blue LED Communication Condition Off USB suspend On continuously Power on, system idle Short blinks in multiple pulses. Occurs while transferring data to/ from the host. Receiving data Access Point Address Scan the bar code below to determine the address of the Access Point you are using.
High (4200 Hz) Batch Mode Batch mode is used to store bar code data when a scanner is out of range of its host, or when performing inventory. The scanner may store a number of symbols (approximately 500 U.P.C. symbols; others may vary) when it is out of range and then send them to the host when back in range or when the records are manually transmitted. Note: Batch mode has limitations when using multiple scanners with one Access Point.
Batch Mode Beep When scanning in Inventory Batch Mode (page 3-16), the scanner beeps every time a bar code is scanned. When Batch Mode Beep is On, you will also hear a click when each bar code is sent to the host. If you do not want to hear these clicks, scan Batch Mode Beep Off. Default = Batch Mode Beep On. Batch Mode Beep Off * Batch Mode Beep On Batch Mode Storage When a scanner is storing data during a Batch Mode process, you can select whether the data is stored in Flash memory or in RAM.
Batch Mode Quantity On Entering Quantities Quantity Codes (page 3-19) allow you to enter a quantity for the last item scanned, up to 9999 (default = 1). Quantity digits are shifted from right to left, so if a 5th digit is scanned, the 1st digit scanned is discarded and the 2nd, 3rd and 4th digits are moved to the left to accommodate the new digit. For example, if the Quantity 5 bar code is scanned after the quantity has been set to 1234, then the 1 is dropped, the quantity will be 2345.
4 5 6 7 8 9 Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. Batch Mode LIFO Total Records Honeywell proprietary & Confidential If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.
Delete Last Code If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code. Delete Last Code Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes. Clear All Codes Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-16), you must scan the following bar code to transmit all the stored data to the host system.
Host Acknowledgment Some applications require that the host validate incoming bar code data (database look-up) and provide acknowledgment to the scanner whether or not to proceed. In Host ACK Mode, the scanner waits for this acknowledgment after each scan. Visual and audible acknowledgments provide valuable feedback to the scan operator. The Host ACK functionality is controlled via a number of pre-defined escape commands that are sent to the scanner to make it behave in different ways.
Host ACK On/Off Host ACK On * Host ACK Off Host ACK Timeout You can set a timeout for the length of time the scanner waits for a valid escape command when using Host Acknowledgment Mode. Set the length (in seconds) for a timeout by scanning the following bar code, then setting the timeout (from 190 seconds) by scanning digits from the Programming Chart inside the back cover of this manual, then scanning Save. Default = 10.
4 Input/Output Settings Programmable Button The second, smaller button on the scanner can be programmed so that pressing the button displays a virtual keyboard on the host, displays the battery charge status, puts the scanner into flashlight mode, or pairs and unpairs the Bluetooth connection between the scanner and the host. You may program one of these selections to occur after a short button press, and another selection to occur after a long button press.
Battery Charge Status If you want the battery indicator LED to flash in a pattern that indicates the battery charge level, scan one of the following bar codes.
Bluetooth Pair/Unpair The programmable button can be used to toggle between pairing and unpairing from the host.
Power Up Beeper The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On. Power Up Beeper Off * Power Up Beeper On Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On bar code below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off.
Good Read and Error Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = Beeper - Good Read On. Beeper - Good Read Off * Beeper - Good Read On Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High.
High (4200 Hz) Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz. * Razz (250 Hz) Medium (3250 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another.
Manual Trigger Modes When in manual trigger mode, the scanner scans until a bar code is read or until the scan button is released. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode. Enhanced mode is best used when you require a very fast scan speed and don’t require a long working range. Default = Manual Trigger-Normal.
Poor Quality PDF Codes This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. When Poor Quality PDF On is scanned, poor quality PDF code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 1D bar code reading. Default = Poor Quality PDF Reading Off.
Character Activation Mode You may use a character sent from the host to trigger the scanner to begin scanning. When the activation character is received, the scanner continues scanning until either the Character Activation Timeout (page 4-11), the deactivation character is received (see Deactivation Character on page 4-11), or a bar code is transmitted.
Character Activation Timeout You can set a timeout for the length of time the illumination remains on and attempting to decode bar codes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart inside the back cover of this manual, then scanning Save. Default = 30,000 ms.
Aimer Delay The aimer delay allows a delay time for the operator to aim the scanner before the bar code is read. Use these codes to set the time between when the button is pressed and when the bar code is read. During the delay time, the aiming light will appear, but the LEDs won’t turn on until the delay time is over. Default = Off.
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Bar Code 1 passes through the centering window, it will be read. Bar Code 2 does not pass through the centering window, so it will not be read. 0% Bar Code 1 10 Bar Code 2 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100% Note: A bar code needs only to be touched by the centering window in order to be read.
Right of Centering Window Preferred Symbology The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both bar code symbologies appear on the same label, but the lower priority symbology cannot be disabled. For example, you may be using the scanner in a retail setting to read U.P.C. symbols, but have occasional need to read a code on a drivers license.
If you want to set additional low priority symbologies, scan FF, then scan the 2 digit hex value from the Programming Chart for the next symbology. You can program up to 5 low priority symbologies. Scan Save to save your selection. Default = None. Low Priority Symbology Preferred Symbology Time-out Once you have enabled Preferred Symbology and entered the high and low priority symbologies, you must set the time-out period.
5. End Output Sequence Editor Scan F F to enter an Output Sequence for an additional symbology, or Save to save your entries. Other Programming Selections • Discard This exits without saving any Output Sequence changes. Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example.
41 start character match for Code 39, 41h = “A” FF termination string for first code 6A code identifier for Code 128 0013 B - Code 128 sample length (12) plus CR suffix (1) = 13 42 start character match for Code 128, 42h = “B” FF termination string for second code 69 code identifier for Code 93 0012 C - Code 93 sample length (11) plus CR suffix (1) = 12 43 start character match for Code 93, 43h = “C” FF termination string for third code Output Sequence Editor Enter Sequence Default Seq
When the output sequence is Off, the bar code data is output to the host as the scanner decodes it. Default = Off. Note: This selection is unavailable when the Multiple Symbols Selection is turned on. Required On/Not Required *Off Multiple Symbols When this programming selection is turned On, it allows you to read multiple symbols with a single press of the scanner’s button.
Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. The Video Reverse Off bar code below is an example of this type of bar code. Scan Video Reverse Only to read only inverted bar codes. Scan Video Reverse and Standard Bar Codes to read both types of codes. Note: After scanning Video Reverse Only, menu bar codes cannot be read. You must scan Video Reverse Off or Video Reverse and Standard Bar Codes in order to read menu bar codes.
* Upright Vertical, Bottom to Top Upside Down Honeywell proprietary & Confidential Released C 4 - 20 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC HEC: EAR99 TEC: EAR99 GOV: ESO1.
5 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string. Prefix and Suffix characters are data characters that can be sent before and after scanned data.
Example: Add a Tab Suffix to All Symbologies Step 1. Scan Add Suffix. Step 2. Scan 9, 9 from the Programming Chart inside the back cover of this manual to apply this suffix to all symbologies. Step 3. Scan 0, 9 from the Programming Chart inside the back cover of this manual. This corresponds with the hex value for a horizontal tab, shown in the ASCII Conversion Chart (Code Page 1252), beginning on page A-3. Scan Save, or scan Discard to exit without saving.
Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in ASCII Conversion Chart (Code Page 1252) starting on page A-3. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.
Next, scan the Character to Trigger Delay bar code, tthen the 2-digit hex value for a printable character to trigger the delay (see Lower ASCII Reference Table on page A-4). Delay Length Character to Trigger Delay To remove this delay, scan the Delay Length bar code, and set the number of delays to 0. Scan the Save bar code using the Programming Chart inside the back cover of this manual.
6 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None. Normally, when you scan a bar code, it is output automatically.
Step 5. Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming Chart inside the back cover of this manual. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths. Step 6. Editor Commands Refer to Data Format Editor Commands (page 6-3). Scan the symbols that represent the command you want to enter. Step 7. Scan Save to save your data format, or Discard to exit without saving your changes.
Terminal ID Table Terminal USB Serial Keyboard Model(s) PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) PS2 compatibles AT compatibles Terminal ID 124 125 134 130 131 128 129 000 000 051 003 002 Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your input data string.
F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 1234567890 ABCDEFGHIJ Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss” character.
Move Commands Move the cursor forward a number of characters F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. F5 Example: Move the cursor forward and send the data Move the cursor forward 3 characters, then send the rest of the bar code data from the bar code above. End with a carriage return.
Search Commands Search forward for a character F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command. Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list, and xxyy .. zz is the list of characters to be suppressed.
The data is output as: 1234 5678 ABC Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation. Data Formatter When Data Formatter is turned Off, the bar code data is output to the host as read, including prefixes and suffixes. Data Formatter Off You may wish to require the data to conform to a data format you have created and saved.
Data Format Non-Match Error Tone When a bar code is encountered that doesn’t match your required data format, the scanner normally generates an error tone. However, you may want to continue scanning bar codes without hearing the error tone. If you scan the Data Format Non-Match Error Tone Off bar code, data that doesn’t conform to your data format is not transmitted, and no error tone will sound.
For example, you may have set your device to the data format you saved as Data Format 3. You can switch to Data Format 1 for a single button press by scanning the Single Scan-Data Format 1 bar code below. The next bar code that is scanned uses Data Format 1, then reverts back to Data Format 3. Single Scan-Primary Data Format Single Scan-Data Format 1 Single Scan-Data Format 2 6 - 11 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released HEC: EAR99 Honeywell proprietary & Confidential Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC 6 - 12 TEC: EAR99 GOV: ESO1.
7 Symbologies This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults.
Message Length Description You are able to set the valid reading length of some of the bar code symbologies. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread. EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09Max. length = 20 EXAMPLE: Decode only those bar codes with a count of 15 characters. Min. length = 15Max.
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character.
Maximum Message Length Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Off Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit Code 39 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48. Minimum Message Length Maximum Message Length Code 39 Append This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to the host computer.
Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.
Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
Maximum Message Length NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Off Code 93 Message Length 7-9 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Code 93 Append This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 bar codes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the order in which the bar codes are read, deleting the first space from each.
Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On/Off On * Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Straight 2 of 5 IATA (two-bar start/stop) Straight 2 of 5 IATA On/Off On * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Matrix 2 of 5 Matrix 2 of 5 On/Off On * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length 7 - 13 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Code 11 Code 11 On/Off On * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Message Length GOV: ESO1.0 Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Code 128 Code 128 On/Off * On Off ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license.
Code 128 Append This function allows the scanner to append the data from several Code 128 bar codes together before transmitting them to the host computer. When the scanner encounters a Code 128 bar code with the append trigger character(s), it buffers Code 128 bar codes until it reads a Code 128 bar code that does not have the append trigger. The data is then transmitted in the order in which the bar codes were read (FIFO). Default = On.
GS1-128 GS1-128 On/Off * On Off GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80. Minimum Message Length 7 - 17 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Telepen Telepen On/Off On * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output.
UPC-A UPC-A On/Off * On Off Note: To convert UPC-A bar codes to EAN-13, see Convert UPC-A to EAN-13 on page 7-24. UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On.
UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 7-20. Default = Not Required.
UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes. If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single scan, it transmits both as one symbology. Otherwise, it transmits the first coupon code it reads.
UPC-E0 UPC-E0 On/Off Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1 (page 7-24). Default = On. * UPC-E0 On UPC-E0 Off UPC-E0 Expand UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off. On * Off When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required.
UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. * On Off UPC-E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On.
5 Digit Addenda On * 5 Digit Addenda Off UPC-E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 7-22). If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection. Default = Off. UPC-E1 On * UPC-E1 Off EAN/JAN-13 GOV: ESO1.0 EAN/JAN-13 On/Off Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a zero to the front.
* Do not Convert UPC-A EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On 5 Digit Addenda On EAN/JAN-13 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda.
* Not Required EAN/JAN-13 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. * On Off Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code (page 7-21). ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off.
EAN/JAN-8 EAN/JAN-8 On/Off * On Off EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off EAN/JAN-8 Addenda C Released 5 Digit Addenda On 7 - 27 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
* 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required. Required * Not Required EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On.
MSI MSI On/Off On * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
Validate Type 11 then Type 10 Character and Transmit Disable MSI Check Characters MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On Off GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On 7 - 31 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC Honeywell proprietary & Confidential HEC: EAR99 TEC: EAR99 GOV: ESO1.
GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On Off GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. Minimum Message Length Maximum Message Length Trioptic Code Trioptic Code is used for labeling magnetic storage media.
Codablock A Codablock A On/Off On * Off Codablock A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600. Minimum Message Length 7 - 33 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Codablock F Codablock F On/Off On * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048. Minimum Message Length Maximum Message Length Label Code GOV: ESO1.0 The standard Label Code is used in libraries. Default = Off.
PDF417 < Default All PDF417 Settings > PDF417 On/Off * On Off PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.
MicroPDF417 < Default All MicroPDF417 Settings > MicroPDF417 On/Off On * Off MicroPDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology.
UPC/EAN Version Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off. UPC/EAN Version On * UPC/EAN Version Off Note: If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1 DataBar code. See Coupon GS1 DataBar Output (page 7-21) for further information.
GS1 DataBar Emulation GS1 Code Expansion Off EAN8 to EAN13 Conversion * GS1 Emulation Off TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar code readers are capable of reading the Code 39 linear component. The MicroPDF417 component can only be decoded if TLC39 On is selected. The linear component may be decoded as Code 39 even if TLC39 is off. Default = Off.
QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089. Minimum Message Length Maximum Message Length QR Code Append This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to the host computer.
Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Off Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116. Minimum Message Length Maximum Message Length This function allows the scanner to append the data from several Data Matrix bar codes together before transmitting them to the host computer.
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly. Data Matrix Code Page MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off On * Off MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information.
Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Off Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832. Minimum Message Length Maximum Message Length This function allows the scanner to append the data from several Aztec bar codes together before transmitting them to the host computer.
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly. Aztec Code Page Chinese Sensible (Han Xin) Code < Default All Han Xin Settings > Han Xin Code On/Off On * Off Han Xin Code Message Length Scan the bar codes below to change the message length.
Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D Postal Codes Off.
Postnet On Also see Postnet Check Digit, page 7-47. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Bar Code and Postnet with B and B’ Fields On Postnet and Postal-4i On C Released Planet Code and Postnet On 7 - 45 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and Intelligent Mail Bar Code On Planet Code, Postnet, and Postal-4i On Planet Code, Postnet, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Intelligent Mail Bar Code On Released C Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On 7 - 46 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet On Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Planet Code Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data.
Combination C and N Tables causes the field to be interpreted using either the C or N Tables. * Bar Output Numeric N Table Alphanumeric C Table Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selections can be active at a time. China Post (Hong Kong 2 of 5) GOV: ESO1.
Maximum Message Length Korea Post Korea Post On * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released HEC: EAR99 Honeywell proprietary & Confidential Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC 7 - 50 TEC: EAR99 GOV: ESO1.
8 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power cycled. Add Code I.D.
Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The programming function will still occur, but in addition, the content of that programming code is output to the terminal. Note: This feature should not be used during normal scanner operation. On * Off TotalFreedom TotalFreedom is an open system architecture that makes it possible for you create applications that reside on your scanner.
EZConfig-Scanning Introduction EZConfig-Scanning provides a wide range of PC-based programming functions that can be performed on a scanner connected to your PC. EZConfig-Scanning allows you to download upgrades to the scanner's firmware, change programmed parameters, and create and print programming bar codes. Using EZConfig-Scanning, you can even save/open the programming parameters for a scanner.
Resetting the Factory Defaults This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. ! If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults. This resets the scanner to the factory default settings.
9 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an RS232 interface (see page 2-12). The following commands can be sent via a PC COM port using terminal emulation software.
SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and SubTag fields. Concatenation of Multiple Commands Multiple commands can be issued within one Prefix/Storage sequence.
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled; the Minimum Message Length (MIN) is set to 2 characters; the Maximum Message Length (MAX) is set to 60 characters; and the Default setting (DFT) has no value. Trigger Commands You can activate and deactivate the scanner with serial trigger commands.
Menu Commands Selection Setting Serial Command * Indicates default # Indicates a numeric entry Page Product Default Settings Pairing the Scanner with Bluetooth Devices Setting Custom Defaults Resetting the Custom Defaults Bluetooth HID Keyboard Connect PAPBTH 1-3 Bluetooth HID Japanese Keyboard Connect PAPJKB 1-3 Pairing the Scanner with an Apple Device Using SPP PAPMFI 1-4 Set Custom Defaults MNUCDP 1-6 Save Custom Defaults MNUCDS 1-6 Activate Custom Defaults DEFALT 1-6 *U.S.A.
Setting Serial Command * Indicates default # Indicates a numeric entry Greek (319 Latin) KBDCTY65 2-4 Greek (319) KBDCTY62 2-4 Greek (Latin) KBDCTY63 2-4 Greek (MS) KBDCTY66 2-4 Greek (Polytonic) KBDCTY60 2-4 Hebrew KBDCTY12 2-4 Hungarian (101 key) KBDCTY50 2-4 Hungary KBDCTY19 2-4 Iceland KBDCTY75 2-4 Irish KBDCTY73 2-4 Italian (142) KBDCTY56 2-4 Italy KBDCTY5 2-5 Japan ASCII KBDCTY28 2-5 Kazakh KBDCTY78 2-5 Kyrgyz (Cyrillic) KBDCTY79 2-5 Latin America KBDC
Selection Switzerland (German) KBDCTY6 2-7 Tatar KBDCTY85 2-8 Turkey F KBDCTY27 2-8 Turkey Q KBDCTY24 2-8 Ukrainian KBDCTY76 2-8 United Kingdom KBDCTY7 2-8 United Stated (Dvorak right) KBDCTY89 2-8 United States (Dvorak left) KBDCTY88 2-8 United States (Dvorak) KBDCTY87 2-8 Page KBDCTY30 2-8 KBDCTY77 2-8 *Regular KBDSTY0 2-9 Caps Lock KBDSTY1 2-9 Shift Lock KBDSTY2 2-9 Automatic Caps Lock KBDSTY6 2-9 Emulate External Keyboard KBDSTY5 2-9 *Keyboard Conversion O
Plug and Play Codes: IBM SurePos Plug and Play Codes: USB Remote MasterMind for USB Plug and Play Codes IBM Port 5B Interface PAPP5B 2-13 IBM Port 9B HHBCR-1 Interface PAP9B1 2-13 IBM Port 17 Interface PAPP17 2-13 IBM Port 9B HHBCR-2 Interface PAP9B2 2-13 RS485 Packet Mode On RTLPDF1 2-13 RS485 Packet Mode Off RTLPDF0 2-13 Page RS485 Packet Length (20-256) RTLMPS 2-14 USB IBM SurePos Handheld PAPSPH 2-14 USB IBM SurePos Tabletop PAPSPT 2-14 USB Keyboard (PC) PAP124 2-14 USB
Setting Serial Command * Indicates default # Indicates a numeric entry 7 Data, 2 Stop, Parity Odd 232WRD7 2-19 8 Data, 1 Stop, Parity Even 232WRD5 2-19 *8 Data, 1 Stop, Parity None 232WRD2 2-20 8 Data, 1 Stop, Parity Odd 232WRD8 2-20 8 Data, 1 Stop, Parity Mark 232WRD14 2-20 RS232 Receiver Time-out Range 0 - 300 seconds 232LPT### 2-20 RS232 Handshaking *RTS/CTS Off 232CTS0 2-21 Flow Control, No Timeout 232CTS1 2-20 Two-Direction Flow Control 232CTS2 2-20 Selection Scanner-B
Setting Serial Command * Indicates default # Indicates a numeric entry Maximum Link Attempts Maximum Link Attempts BT_MLA 3-3 Relink Time-Out Relink Time-Out BT_RLT 3-3 Reset Scanner Reset Scanner RESET_ 3-6 Scanner Report Scanner Report RPTSCN 3-6 Scanner Address Scanner Address BT_LDA 3-7 Linked Modes Locked Link Mode BASCON0,DNG1 3-7 *Open Link Mode BASCON1,DNG1 3-7 Unlink Scanner BT_RMV 3-7 Override Locked Scanner BT_RPL1 3-8 Out-of-Range Alarm Scanner Alarm Duratio
Selection Batch Mode Batch Mode Beep Serial Command * Indicates default # Indicates a numeric entry Automatic Batch Mode BATENA1 3-16 *Batch Mode Off BATENA0 3-16 Inventory Batch Mode BATENA2 3-16 Persistent Batch Mode BATENA3 3-16 Off BATBEP0 3-17 *On BATBEP1 3-17 Page *Flash Storage BATNVS1 3-17 RAM Storage BATNVS0 3-17 Batch Mode Quantity *Off BATQTY0 3-17 On BATQTY1 3-17 Quantity Codes 0 BATNUM0 3-18 *1 BATNUM1 3-18 2 BATNUM2 3-18 3 BATNUM3 3-18 4 BATNU
Power Up Beeper Beep on BEL Character Trigger Click Beeper - Good Read Beeper Volume - Good Read Beeper Pitch - Good Read (Frequency) Beeper Pitch - Error (Frequency) Beeper Duration - Good Read Bluetooth Pair/Unpair On - Short Press BTNSEC4 4-3 Bluetooth Pair/Unpair On - Long Press BTNSCL4 4-3 *Disable Short Press BTNSEC0 4-3 *Disable Long Press BTNSCL0 4-3 Page Power Up Beeper Off BEPPWR0 4-4 *Power Up Beeper On BEPPWR1 4-4 Beep on BEL On BELBEP1 4-4 *Beep on BEL Off BELBEP0 4-
CodeGate Mobile Phone Read Mode Character Activation Mode DECLDI1 4-8 *Poor Quality 1D Reading Off DECLDI0 4-8 Poor Quality PDF Reading On PDFXPR1 4-9 *Poor Quality PDF Reading Off PDFXPR0 4-9 *CodeGate Off Out-of-Stand AOSCGD0. 4-9 CodeGate On Out-of-Stand AOSCGD1.
Setting Serial Command * Indicates default # Indicates a numeric entry Output Sequence Editor Enter Sequence SEQBLK 4-17 Default Sequence SEQDFT 4-17 Partial Sequence Transmit Partial Sequence SEQTTS1 4-17 *Discard Partial Sequence SEQTTS0 4-17 Required SEQ_EN2 4-18 On/Not Required SEQ_EN1 4-18 Selection Require Output Sequence Multiple Symbols No Read Video Reverse Page *Off SEQ_EN0 4-18 On SHOTGN1 4-18 *Off SHOTGN0 4-18 On SHWNRD1 4-18 *Off SHWNRD0 4-18 Video Rev
Selection Data Formatter Data Format Non-Match Error Tone Primary/Alternate Data Formats Single Scan Data Format Change Setting Serial Command * Indicates default # Indicates a numeric entry Data Formatter Off DFM_EN0 6-9 *Data Formatter On, Not Required, Keep Prefix/Suffix DFM_EN1 6-9 Data Format Required, Keep Prefix/Suffix DFM_EN2 6-9 Data Formatter On, Not Required, Drop Prefix/Suffix DFM_EN3 6-9 Data Format Required, Drop Prefix/Suffix DFM_EN4 6-9 *Data Format Non-Match Error Ton
Setting Serial Command * Indicates default # Indicates a numeric entry Code 39 Start/Stop Char. *Don’t Transmit C39SSX0 Transmit C39SSX1 7-4 Code 39 Check Char. *No Check Char.
Setting Serial Command * Indicates default # Indicates a numeric entry Code 93 Code Page Code 93 Code Page C93DCP 7-10 Straight 2 of 5 Industrial Default All Straight 2 of 5 Industrial Settings R25DFT 7-11 *Off R25ENA0 7-11 R25ENA1 7-11 Minimum (1 - 48) *4 R25MIN## 7-11 Maximum (1 - 48) *48 R25MAX## 7-11 Straight 2 of 5 IATA Default All Straight 2 of 5 IATA Settings A25DFT 7-12 Straight 2 of 5 IATA Message Length Matrix 2 of 5 Matrix 2 of 5 Message Length Code 11 Code 11 Check D
Telepen Output Telepen Message Length UPC-A UPC-A Check Digit UPC-A Number System UPC-A 2 Digit Addenda UPC-A 5 Digit Addenda Default All Telepen Settings TELDFT 7-18 *Off TELENA0 7-18 On TELENA1 7-18 *AIM Telepen Output TELOLD0 7-18 Original Telepen Output TELOLD1 7-18 Page Minimum (1 - 60) *1 TELMIN## 7-18 Maximum (1 - 60) *60 TELMAX## 7-18 Default All UPC-A Settings UPADFT 7-19 Off UPBENA0 7-19 *On UPBENA1 7-19 Off UPACKX0 7-19 *On UPACKX1 7-19 Off UPANSX0 7-19 *
UPC-E0 Addenda UPC-E1 EAN/JAN-13 Convert UPC-A to EAN-13 EAN/JAN-13 Check Digit EAN/JAN-13 2 Digit Addenda EAN/JAN-13 Addenda Required EAN/JAN-13 Addenda Separator ISBN Translate EAN/JAN-8 EAN/JAN-8 Addenda Serial Command * Indicates default # Indicates a numeric entry 2 Digit Addenda On UPEAD21 7-23 *2 Digit Addenda Off UPEAD20 7-23 5 Digit Addenda On UPEAD51 7-23 Page *5 Digit Addenda Off UPEAD50 7-23 *Off UPEEN10 7-24 On UPEEN11 7-24 Default All EAN/ JAN Settings E13DFT 7-24
MSI Check Character MSI Message Length GS1 DataBar Omnidirectional GS1 DataBar Limited GS1 DataBar Expanded GS1 DataBar Expanded Msg.
PDF417 PDF417 Msg. Length MacroPDF417 MicroPDF417 MicroPDF417 Msg.
Setting Serial Command * Indicates default # Indicates a numeric entry Default All MaxiCode Settings MAXDFT 7-41 On MAXENA1 7-41 *Off MAXENA0 7-41 Minimum (1-150) *1 MAXMIN### 7-41 Maximum (1-150) *150 MAXMAX### 7-41 Default All Aztec Code Settings AZTDFT 7-42 *On AZTENA1 7-42 Off AZTENA0 7-42 Aztec Code Msg.
Combination 2D Postal Codes Planet Code Check Digit Postnet Check Digit # Indicates a numeric entry InfoMail and British Post On POSTAL8 7-45 Intelligent Mail Bar Code and Postnet with B and B’ Fields On POSTAL20 7-45 Postnet and Postal-4i On POSTAL14 7-45 Postnet and Intelligent Mail Bar Code On POSTAL16 7-45 Postal-4i and Intelligent Mail Bar Code On POSTAL17 7-45 Postal-4i and Postnet with B and B’ Fields On POSTAL19 7-45 Planet and Postnet On POSTAL12 7-45 Planet and Postnet with
Selection Setting Serial Command * Indicates default # Indicates a numeric entry Default All China Post (Hong Kong 2 of 5) Settings CPCDFT 7-48 *Off CPCENA0 7-48 Page Postal Codes - Linear China Post (Hong Kong 2 of 5) On CPCENA1 7-48 China Post (Hong Kong 2 of 5) Msg. Length Minimum (2 - 80) *4 CPCMIN## 7-48 Maximum (2 - 80) *80 CPCMAX## 7-48 Korea Post Default All Korea Post Settings KPCDFT 7-49 *Off KPCENA0 7-49 On KPCENA1 7-49 Korea Post Msg.
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released HEC: EAR99 Honeywell proprietary & Confidential Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC 9 - 24 TEC: EAR99 GOV: ESO1.
10 Product Specifications Voyager 1602g Wireless Pocket Scanner Product Specifications Parameter Specification Mechanical Height .9 in. (22mm) Length 4.7 in. (120mm) Width 1.9 in. (48mm) Weight 3.5 oz. (100g) Electrical Battery: Lithium Ion 3.7v 750mAh Number of Scans up to 2250 from full charge Expected Hours of Operation 12 from full charge Expected Charge Time 3 - 5 hours Illumination LED White emitting color Aiming 624nm peak wavelength Radio Frequency 2.4 to 2.
Parameter Specification 20 mil Code 39 66 - 425mm (2.6 - 16.73 in.) 6.7 mil PDF417 62 - 108mm (2.44 - 4.25 in.) 10mil Data Matrix 54 - 108mm (2.13 - 4.25 in.) 20mil QR Code 41 - 230mm (1.61 - 9.05 in.) *Storage outside of this temperature range could be detrimental to battery life.
Standard Connector Pinout Note: Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty. Micro-B USB 1 2 3 4 5 Vcc Data Data + ID Ground 10 - 3 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released HEC: EAR99 Honeywell proprietary & Confidential Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC 10 - 4 TEC: EAR99 GOV: ESO1.
11 Maintenance and Troubleshooting Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center Customer Support on page -ix. Maintenance Your device provides reliable and efficient operation with a minimum of care.
Replacing a Battery Step 1. Use a Phillips head screwdriver to remove the back cover of the scanner. Step 2. Lift the back cover up and out to expose the battery. Honeywell proprietary & Confidential C Released Step 4. Replace the back cover and secure with the Phillips head screw. 11 - 2 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Troubleshooting Note: Make sure that your scanner’s battery is charged. Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for both the scanner and the host. Is the scanner having trouble reading your symbols? If the scanner isn’t reading symbols well, check that the symbols: • Aren’t smeared, rough, scratched, or exhibiting voids. • Aren’t coated with frost or water droplets on the surface. • Are enabled in the host to which the scanner connects.
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released HEC: EAR99 Honeywell proprietary & Confidential Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC 11 - 4 TEC: EAR99 GOV: ESO1.
A Reference Charts Symbology Charts Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details. Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry. Refer to Data Editing beginning on page 5-1 and Data Formatting beginning on page 6-1 for information about using Code ID and AIM ID.
AIM Symbology UPC-A ID Possible modifiers (m) ]E0 Honeywell ID Hex c 63 UPC-A with Add-On ]E3 c 63 UPC-A with Extended Coupon Code ]E3 c 63 UPC-E ]E0 E 45 UPC-E with Add-On ]E3 E 45 UPC-E1 ]X0 E 45 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity 5 35 2D Symbologies AIM Honeywell ID Possible modifiers (m) ID Hex Aztec Code ]zm 0-9, A-C z 7A Chinese Sensible Code (Han Xin Code) ]X0 H 48 Codablock A ]O6 0, 1, 4, 5, 6
AIM Symbology ID British Post Possible modifiers (m) Honeywell ID Hex ]X0 B 42 Canadian Post ]X0 C 43 China Post ]X0 Q 51 InfoMail ]X0 , 2c Intelligent Mail Bar Code ]X0 M 4D Japanese Post ]X0 J 4A KIX (Netherlands) Post ]X0 K 4B Korea Post ]X0 ? 3F Planet Code ]X0 L 4C Postal-4i ]X0 N 4E Postnet ]X0 P 50 ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below.
Non-printable characters ASCII control Keyboard Control + ASCII (CTRL+X) Mode Windows Mode Control + X Mode On (KBDCAS2) DEC HEX Char Control + X Mode Off (KBDCAS0) CTRL + X 23 17 ETB F2 CTRL+ W 24 18 CAN F3 CTRL+ X 25 19 EM F4 CTRL+ Y 26 1A SUB F5 CTRL+ Z 27 1B ESC F6 CTRL+ [ 28 1C FS F7 CTRL+ \ 29 1D GS F8 CTRL+ ] 30 1E RS F9 CTRL+ ^ 31 1F US F10 CTRL+ - 127 7F ⌂ NP Enter CTRL + X function Lower ASCII Reference Table Note: Windows Code page 1252 an
Printable Characters (Continued) DEC HEX Character DEC HEX 63 3F 95 5F DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 128 80 € Ç up arrow ↑ 0x48 129 81 ü down arrow ↓ 0x50 130 82 ‚ é right arrow → 0x4B 131 83 ƒ â left arrow ← 0x4D 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98
Alternate Extended PS2 Scan Code 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 ¯ ° ± ² ³ ´ µ ¶ · ¸ ¹ º » ¼ ½ ¾ ¿ À Á Â Ã Ä Å Æ Ç È É Ê Ë Ì Í Î Ï Ð Ñ Ò Ó Ô Õ Ö × Ø Ù Ú Û Ü Ý Þ ß à á â » ░ ▒
Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF ã ä å æ ç è é ê ë ì í î ï ð ñ ò ó ô õ ö ÷ ø ù ú û ü ý þ ÿ π Σ σ µ τ Φ Θ Ω δ ∞ φ ε ∩ ≡ ± ≥ ≤ ⌠ ⌡ ÷ ≈ ° · · √ ⁿ ² ■ Alternate Extended PS2 Scan Code ISO 2022/ISO 646 Character Replacements Standard Keyboard Country Honeywell Code Page Opt
Code Page Selection Method/Country Standard Keyboard Country Honeywell Code Page Option ISO/IEC 646-57 92 99 Great Britain (UK) ISO /IEC 646-04 7 87 France ISO /IEC 646-69 3 83 Germany ISO/IEC646-21 4 84 Switzerland ISO /IEC 646-CH 6 86 Sweden / Finland (extended Annex C) ISO/IEC 646-11 2 82 Ireland ISO /IEC 646-207 73 97 Denmark ISO/IEC 646-08 8 88 Norway ISO/IEC 646-60 9 94 Italy ISO/IEC 646-15 5 85 Portugal ISO/IEC 646-16 13 92 Spain ISO/IEC 646-17 10 90
64 91 92 93 94 96 123 124 125 126 Hex 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E US 0 1 # $ @ [ \ ] ^ ` { | } ~ CA 54 95 # $ à â ç ê î ô é ù è û CA 18 96 # $ à â ç ê É ô é ù è û JP 28 98 # $ @ [ ¥ ] ^ ` { | } ⎯ CN 92 99 # ¥ @ [ \ ] ^ ` { | } ⎯ GB 7 87 £ $ @ [ \ ] ^ ` { | } ˜ FR 3 83 £ $ à ° ç § ^ µ é ù è ¨ DE 4 84 # $ § Ä Ö Ü ^ ` ä ö ü ß CH 6 86 ù $ à é ç ê î ô ä
Keyboard Key Maps 6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2B 4B 50 55 4C 51 56 2C 2E 2F 30 31 32 33 34 35 36 37 39 3D 3A 3B 3C 3E 3F 38 40 53 4F 54 59 5A 5F 5B 60 5C 61 5D 62 63 64 69 65 6A 66 67 6C 68 5A 5F 5B 60 5C 61 5D 62 63 64 69 65 6A 66 67 6C 68 104 Key U.S.
Sample Symbols UPC-A Interleaved 2 of 5 0 123456 7890 1234567890 EAN-13 9 780330 290951 Code 128 Code 128 Code 39 BC321 A13579B Code 93 Straight 2 of 5 Industrial Honeywell proprietary & Confidential 123456-9$ C Released 123456 VG1602-UG Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC HEC: EAR99 TEC: EAR99 GOV: ESO1.0 Codabar The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012 PDF417 Car Registration Data Matrix Test Symbol QR Code Aztec Numbers MaxiCode HEC: EAR99 Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC Test Message Test Message Postnet VG1602-UG C Released Zip Code Honeywell proprietary & Confidential Micro PDF417 TEC: EAR99 GOV: ESO1.0 Package Label The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
4-CB (4-State Customer Bar Code) 01,234,567094,987654321,01234567891 ID-tag (UPU 4-State) VG1602-UG C Released Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC Honeywell proprietary & Confidential HEC: EAR99 TEC: EAR99 GOV: ESO1.0 J18CUSA8E6N062315014880T The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Programming Chart 0 1 2 3 4 5 6 VG1602-UG C Released Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC 9 Honeywell proprietary & Confidential 8 HEC: EAR99 TEC: EAR99 GOV: ESO1.0 7 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Programming Chart A B C D E F Save Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. VG1602-UG C Released Honeywell proprietary & Confidential Reset Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC HEC: EAR99 TEC: EAR99 GOV: ESO1.0 Discard The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 VG1602-UG Rev C 3/16 The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing. VG1602-UG C Released Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC Honeywell proprietary & Confidential HEC: EAR99 TEC: EAR99 GOV: ESO1.0 www.honeywellaidc.
Rev E Product documentation is available at www.honeywellaidc.com. La documentation sur le produit est disponible à www.honeywellaidc.com. La documentation du produit est disponible sur le site www.honeywellaidc.com. La documentazione sul prodotto è disponibile sul sito www.honeywellaidc.com. Die Produktdokumentation ist unter www.honeywellaidc.com verfügbar. La documentación del producto está disponible en www.honeywellaidc.com. La documentación del producto está disponible en www.honeywellaidc.com.
TÜV R Statement TÜV R listed: UL 60950-1, Second Edition and CSA C22.2 No.60950-1-07, Second Edition. TÜV Rheinland C US If the following label is attached to your product, the product meets Korean agency approval: Complies with IDA Standards DA102905 (B ) . Normes TÜV R Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução No. 242/2000 e atende aos requisitos técnicos aplicados.
