ENGLISH Operation & Installation Guide Steel Waterproof Fire Safe with Programmable Digital Lock Model 2605 Read this manual carefully and never store it inside the safe!
Index Welcome / Package Contents ........................................................................ Page 1 Override Access Key / Install Batteries.......................................................... Page 2 Low or Dead Batteries / Testing Digital Lock................................................. Page 3 Programming New User Code / Testing New User Code............................. Page 4 Closing Your Safe / Turn Sound On and Off / Motion Alarm Settings..........
WELCOME Your Honeywell Waterproof Steel Fire and Security Safe will provide years of safe and secure protection for your valuables, important documents and other personal items. All Honeywell safes are designed and built using the highest manufacturing standards to ensure maximum user satisfaction under a variety of conditions. With proper care, your Honeywell safe will provide “Peace of Mind” for many years to come.
OVERRIDE ACCESS KEY Your safe is equipped with an override access key which allows immediate access in case you forget your user codes or the batteries need to be installed or replaced. 1. Remove override access rubber lock cover (Figure 1). 2. Insert the override access key into the lock until it stops (Figure 2). 3. With the key inserted turn clockwise to the right (Figure 3). 4. Turn the door handle upwards counterclockwise and pull the safe door open (Figure 4 & Figure 5).
LOW OR DEAD BATTERIES The battery level meter is located at the top of the keypad. You can check the battery level meter by pressing the key. If it is down to the last red LED on the left of the meter, it is an indicator that the batteries are weak and must be changed immediately. The user code will not be erased if the batteries become weak or are removed. Weak or dead batteries should be replaced immediately and all 4 batteries should be changed.
PROGRAMMING NEW USER CODE For best security, it is recommended that you immediately change the factory preset code to your own personal user code. Programming the User Code 1. Locate and press the inset program button located on the top inside edge of the door (Figure 1). The red and green LED’s will flash and you will have 10 seconds to perform the next 2 steps. 2. Enter a new 3-8 digit user code followed by the # key. Then immediately repeat the same entry followed by the # key to confirm (Figure 2). 3.
CLOSING YOUR SAFE To Lock: 1. Close the safe door and turn handle downward to the left placing the door bolts into the locked position (Figure 1 and Figure 2). Note: Due to the airtight seal, to close you may have to push inward on the door while turning the handle downward clockwise to place the blots fully into the locked position.
SECURE LOCKOUT PERIOD If the wrong user code is entered into the keypad 3 consecutive times in a row, the keypad will automatically go into lockout mode and you will not be able to open the safe using the digital keypad for 15 minutes. During the lockout period entry can be made using the override access key. LOST OR FORGOTTEN USER CODES If the user code is unavailable or your keypad fails due to dead batteries or other malfunction, you can open the safe using the override access key.
ANCHORING YOUR SAFE You may bolt your safe to a shelf or floor for added theft protection and resistance to tipping. Your safe has a pre-drilled bolt-down hole in the floor panel and mounting hardware is provided for securing to concrete surfaces. If bolting to wood or metal additional hardware will be needed. Check with your local home center. To secure your safe to a concrete floor: 1. Select a suitable and convenient location for your safe (Figure 1). 2.
CONSUMER ASSISTANCE EMAIL: LHLPCustomerService@LHLPinc.com WEBSITE: www.honeywellsafes.com ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc. 860 East Sandhill Avenue Carson, CA 90746 USA TELEPHONE: US/Canada 1-877-354-5457 (Toll Free) Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677 to complete your call.
ORDERING ADDITIONAL OVERRIDE ACCESS KEYS The following information is required to order keys: 1. PROOF OF OWNERSHIP (1 of 2 Options Below) A) SALES RECEIPT & IDENTIFICATION – INTERNATIONAL ORDERS ONLY! • Copy of sales receipt showing Store, Date & Product Description. • Copy of your picture I.D. (Drivers license, passport, regular I.D.). B) PRODUCT OWNERSHIP VERIFICATION FORM If sales receipt is not available, contact us by email or telephone to request a “Product Ownership Verification Form”. 2.
Limited Warranty LH Licensed Products, Inc., (“LHLP, Inc.”) warrants that for a period of seven (7) years from the date of purchase, this product will be free from structural or mechanical defects resulting from materials or workmanship. LHLP, Inc., at its sole option and as the purchaser’s sole remedy under this warranty, will repair or replace this product or any component of the product found to be defective during the warranty period.