Install Instructions

ManualsBrandsHoneywell ManualsSwitch272630D

Table Of Contents

INSTALLATION INSTRUCTIONS

Place Bar Code Here

95C-10941EFS-01

272630D Position Feedback and

Auxiliary Switch Accessory

FOR ML6984 AND ML7984

APPLICATION

The 272630D auxiliary board is an optional circuit board

that is used in conjunction with Series 4000 ML6984 and

ML7984 globe valve actuators. This auxiliary board

combines the function of an adjustable low voltage SPDT

auxiliary switch with a 2-10 Vdc or 4-20 mA position

feedback signal. It has a 4-pin keyed connector for

communications from the mother circuit board.

SPECIFICATIONS

Feedback: 2-10 Vdc (10-2 V reverse acting) into mini-

mum impedance 500 ohm. Maximum output current is

20 mA dc.

Auxiliary Switch: SPDT, 24 V, 50/60Hz, 1 A inductive.

Fixed differential (3% of stroke), adjustable operating

point from 0 to 100% of stroke.

INSTALLATION

When installing this product...

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check ratings given in instructions and on the

product to ensure the product is suitable for your

application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

1. Disconnect power supply before beginning

installation to prevent electric shock and

equipment damage.

2. All wiring must comply with applicable local

electrical codes, ordinances and regulations.

3. DO NOT electrically operate the ML6-7984

actuator before assembly to the valve

because damage not apparent to the

installer may occur. Mount the actuator to the

valve before connecting to power.

Assembly

1. Remove plastic cover from the ML6-7984 by loos-

ening the two screws located on the top. (Note:

These screws are captive. Rotate three complete

revolutions to remove cover).

2. Slide the auxiliary board into the two slots at the

bottom of the bridge. Push back and snap the

board into the fingers. (See Fig. 1)

3. Connect one end of the 4-pin connector to the

main board and the other end to the auxiliary board

if it is not already connected. The connectors are

keyed and only install one way.

4. Mount the actuator onto the valve body and con-

nect wiring.

5. Reinstall cover after operational check.

Summary of content (6 pages)

PAGE 1
272630D Position Feedback and Auxiliary Switch Accessory FOR ML6984 AND ML7984 INSTALLATION INSTRUCTIONS APPLICATION The 272630D auxiliary board is an optional circuit board that is used in conjunction with Series 4000 ML6984 and ML7984 globe valve actuators. This auxiliary board combines the function of an adjustable low voltage SPDT auxiliary switch with a 2-10 Vdc or 4-20 mA position feedback signal. It has a 4-pin keyed connector for communications from the mother circuit board.
PAGE 2
72630D POSITION FEEDBACK AND AUXILIARY SWITCH ACCESSORY The 272630D provides: BRIDGE FINGERS 1. 2. 1. INSTALL CIRCUIT BOARD A 2-10 Vdc voltage proportional to the valve stem position. This output is capable of sourcing up to 20 mA dc drive current. An isolated "Form C" relay contact closure that energizes when the valve is open more than the setting of the trimmer potentiometer ("trim pot"). Position feedback voltage mirrors the control signal. For ML6984 and direct acting ML7984 operation, see Fig.
PAGE 3
Accessoire d'interrupteur auxiliaire et de retour de position 272630D POUR ML6984 ET ML7984 NOTICE D'INSTALLATION APPLICATION La carte de circuit auxiliaire 272630D est une carte de circuit auxiliaire utilisée avec les actionneurs de robinet à soupape 4000 ML6984 et ML7984 série 4000. La carte auxiliaire combine les fonctions d'un interrupteur auxiliaire unipolaire bidirectionnel basse tension réglable avec un signal de retour de position de 2-10 V c.c. ou 420 mA.
PAGE 4
ACCESSOIRE D'INTERRUPTEUR AUXILIAIRE ET DE RETOUR DE POSITION 272630D Le 272630D fournit: PONT DOIGTS 1. 2. 1. INSTALLATION DE LA CARTE DE CIRCUIT Une tension de 2-10 V c.c. proportionnelle à la position de la tige de vanne. Cette sortie peut de donner jusqu'à 20 mA de courant d'entraînement. Une fermeture de contact de relais isolée de forme C qui est activée lorsque la vanne est ouverte audelà du réglage du potentiomètre d'ajustement. La tension de retour de position reflète le signal de commande.
PAGE 5
Accesorio de interruptor auxiliar y retroalimentación de posición 272630D PARA ML6984 Y ML7984 INSTRUCCIONES DE INSTALACIÓN APLICACIÓN La placa auxiliar 272630D es un circuito impreso opcional que se utiliza junto con los actuadores para válvulas de globo ML6984 y ML7984 de la serie 4000. Esta placa auxiliar combina la función de un interruptor auxiliar ajustable SPDT para bajo voltaje con una señal de retroalimentación de posición de 2 a 10 V CC o de 4 a 20 mA.
PAGE 6
ACCESORIO DE INTERRUPTOR AUXILIAR Y RETROALIMENTACIÓN DE POSICIÓN 272630D La placa 272630D proporciona lo siguiente: PUENTE LINGUETES 1. 1. INSTALE EL CIRCUITO IMPRESO 2. Un voltaje de 2 a 10 V CC proporcional a la posición del vástago de la válvula. Esta salida puede suministrar hasta 20 mA CC de corriente máxima. Un cierre aislado de contacto del relé "forma C" que se activa cuando la válvula se encuentra abierta más que la configuración del potenciómetro de recorte. RANURAS MS32264 Fig. 9.