3800i Industrial Handheld Linear Imager 3800r Retail/Commercial Handheld Linear Imager ™ User’s Guide
Disclaimer Hand Held Products (“Hand Held Products”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Hand Held Products to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Hand Held Products.
Statement of Agency Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Class B Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules.
The CE mark on the product indicates that the system has been tested to and conforms with the provisions noted within the 89/336/ EEC Electromagnetic Compatibility Directive and the 73/23/EEC Low Voltage Directive. For CE-related inquiries, please contact: Hand Held Products Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands Hand Held Products shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.
Mexico Certified Patents Please refer to the 3800r/3800i packaging for patent information. Solids and Water Protection The 3800i has a rating of IP54, immunity of windblown dust penetration and splashing water. The 3800r has a rating of IP41, immunity of foreign particles and dripping water.
Table of Contents Chapter 1 - Getting Started 3800i/3800r........................................................................... 1-1 About This Manual ............................................................... 1-1 Unpacking the Scanner ......................................................... 1-1 3800i Models ........................................................................ 1-2 3800r Models .......................................................................
Connecting the Scanner with RS-232 Serial Port ................ 2-8 RS-232 Baud Rate.......................................................... 2-9 RS-232 Word Length: Data Bits, Stop Bits, and Parity2-10 RS-232 Handshaking ................................................... 2-11 Wand Emulation Connection ....................................... 2-11 Wand Emulation Transmission Rate............................ 2-12 Wand Emulation Polarity............................................. 2-12 Wand Emulation Idle .
Output Sequence Overview ................................................ 3-10 Output Sequence Editor................................................ 3-11 Require Output Sequence............................................. 3-11 Multiple Symbols................................................................ 3-13 No Read .............................................................................. 3-13 Video Reverse.....................................................................
Secondary Code 39 Wand Emulation................................... 6-2 Secondary Laser Emulation.................................................. 6-3 Laser Emulation Transmission Rate..................................... 6-3 Laser Emulation Polarity ...................................................... 6-4 Laser Emulation Idle............................................................. 6-4 Secondary Trigger Mode ...................................................... 6-4 Hands Free Time-Out .............
Matrix 2 of 5 ....................................................................... 7-13 Matrix 2 of 5 Message Length ..................................... 7-14 Code 11 ............................................................................... 7-14 Check Digits Required ................................................. 7-14 Code 11 Message Length ............................................. 7-15 Code 128 .............................................................................
EAN/JAN 8......................................................................... 7-25 EAN/JAN 8 Check Digit.............................................. 7-25 EAN/JAN 8 Addenda................................................... 7-25 EAN/JAN 8 Addenda Required ................................... 7-25 EAN/JAN 8 Addenda Separator .................................. 7-26 MSI ..................................................................................... 7-26 MSI Check Character...........................
Resetting the Standard Product Defaults .............................. 9-1 Temporary Visual Xpress Configuration.............................. 9-2 Chapter 10 - Visual Xpress Visual Xpress Introduction ................................................. 10-1 Installing Visual Xpress from the Web ........................ 10-2 Chapter 11 - Serial Programming Commands Conventions ........................................................................ 11-1 Menu Command Syntax ...................................
Chapter 14 - Customer Support Product Service and Repair ................................................ 14-1 Online Product Service and Repair Assistance............ 14-2 Technical Assistance .......................................................... 14-2 Online Technical Assistance ........................................ 14-2 Limited Warranty................................................................ 14-2 Appendix A - Appendix A Symbology Chart .....................................................
1 Getting Started 3800i/3800r The 3800i and 3800r mark a new performance level for handheld scanners. Both the 3800i and 3800r are powered by Hand Held Products AdaptusTM Imaging Technology. The performance of Adaptus technology delivers aggressive read rates and depths of field on 1D, stacked linear, and matrix codes. The 3800i handheld industrial image reader is the first industrial class reader to be powered by Hand Held Products Adaptus imaging technology.
3800i Models Note: The Hand Held Products 3800i imager may be used with many interfaces, which are described in this User’s Guide. Refer to the chart below to determine the models that can be used with the interface you are using. Refer to Chapter 6 for programming information regarding Secondary Interfaces. The chart below lists the 3800i scanner models. “SR” indicates “Standard Range” linear optics.
3800r Models Note: The Hand Held Products 3800r scanner may be used with many interfaces, which are described in this user’s guide. Refer to the chart below to determine the models that can be used with the interface you are using. Refer to Chapter 6 for programming information regarding Secondary Interfaces. The chart below lists the 3800r scanner models. “SR” indicates “Standard Range” linear optics.
3800i/3800r Scanner Identification 1-4 3800i/3800r User’s Guide
3800i Scanner (with aimer beam option) Identification 3800i/3800r User’s Guide 1-5
Connecting the Scanner When Powered by Host (Keyboard Wedge) A scanner can be connected between the keyboard and PC as a “keyboard wedge,” plugged into the serial port, or connected to a portable data terminal in wand emulation or non decoded output mode. The following is an example of a keyboard wedge connection: 1. Turn off power to the terminal/computer. 2. Disconnect the keyboard cable from the back of the terminal/ computer. Disconnect 3.
Reading Techniques The scanner has a view finder that projects a bright red aiming beam that corresponds to its horizontal field of view. The aiming line should be centered horizontally over the bar code; it will not read if the aiming line is in any other direction. Good Read Bad Read Bad Read The best focus point for reading most code densities is about 5 inches (12.7 cm) from the unit.
Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge Connection 3800r scanners are factory programmed for a keyboard wedge interface to an IBM PC AT with a USA keyboard. If this is your interface and you do not need to modify the settings, skip to Chapter 3 - Output. If you programmed the scanner for a different terminal interface and you want to change to an IBM PC AT and compatibles keyboard wedge interface, scan the bar code below.
Wand Emulation Plug & Play In Wand Emulation mode, the imager decodes the bar code then sends data in the same format as a wand imager. The Code 39 Format converts all symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code 128 and Interleaved 2 of 5 without any changes, but converts all other symbologies to Code 39. The Wand Emulation Plug & Play Code 39 Format bar code below sets the terminal ID to 61. The Wand Emulation Plug & Play Same Code Format bar code sets the terminal ID to 64.
Each bar code above also programs the following suffixes for each symbology: Symbology EAN 8 EAN 13 UPC A UPC E Code 39 Interleaved 2 of 5 Code 128 * Code 128 ** Suffix 0C 16 0D 0A 00 0A 00 0D 00 0A 00 18 0B 0B 0B 0B * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces **Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface 1 - 10 3800i/3800r User’s Guide
Connecting the Scanner with USB A scanner can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the scanner and to the computer. 2. The scanner beeps. 3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. Note: The following USB “Plug and Play” codes are supported on specific models. Refer to 3800r Models and on page 1-3 to determine if this interface applies to your scanner.
Note: After scanning one of these codes, you must power cycle the cash register. IBM SurePos (USB Handheld Scanner) Interface IBM SurePos (USB Tabletop Scanner) Interface Each bar code above also programs the following suffixes for each symbology: Symbology EAN 8 EAN 13 UPC A UPC E Code 39 Interleaved 2 of 5 Code 128 Suffix 0C 16 0D 0A 00 0A 0B 00 0D 0B 00 18 0B USB PC or Macintosh Keyboard Scan one of the following codes to program the imager for USB PC Keyboard or USB Macintosh Keyboard.
USB HID Scan the following code to program the imager for USB HID bar code scanners. Scanning this code changes the terminal ID to 131. USB HID Bar Code Scanner USB Com Port Emulation Scan the following code to program the imager to emulate a regular RS-232based Com Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Hand Held Products website (www.handheld.com). The driver will use the next available Com Port number.
ACK/NAK Mode On * Off Connecting the Scanner with Serial Wedge The imager uses True and TTL signal levels to wedge into an RS-232 serial network. Use only 3800i/3800r serial wedge cables to prevent damage to the scanner. Refer to Connecting the Scanner with RS-232 Serial Port on page 2-8 to set the baud rate and communications protocol. 1. Turn off power to the computer. 2. Disconnect the existing serial cable from the computer. 3. Connect the appropriate interface cable to the scanner.
To set up the serial wedge terminal ID, use the serial terminal ID 050 and follow the instructions on page 2-1. Set the port to which you want the scanned data to transmit. Port 1 corresponds to P1 on the output cable and Port 2 corresponds to P2 on the output cable. Choosing Both sends scanned data to P1 and P2. Default = P1.
1 - 16 3800i/3800r User’s Guide
2 Terminal Interfaces Terminal ID If your interface is not a standard PC AT, refer to "Supported Terminals" on page 2-2 through page 2-3, and locate the Terminal ID number for your PC. Scan the Terminal ID bar code below, then scan the numeric bar code(s) from the Programming Chart inside the back cover of this manual to program the scanner for your terminal ID. Scan Save to save your selection. For example, an IBM AT terminal has a Terminal ID of 003.
Supported Terminals Terminal DEC DEC Esprit Heath Zenith HP IBM IBM IBM IBM 102 key IBM 122 key IBM 122 key IBM 122 key IBM 122 key IBM DOS/V 106 key IBM SurePOS IBM SurePOS IBM Thinkpad IBM Thinkpad IBM Thinkpad I/O 122 key ITT Lee Data NEC Olivetti Olivetti RS-232 True RS-232 TTL Serial Wedge Silicon Graphics Telex 88 key Telex 88 key Telex 102 key 2-2 Model(s) VT510, 520, 525 (PC style) VT510, 520, 525 (DEC style LK411) 200, 400 PC, AT Vectra XT PS/2 25, 30, 77DX2 AT, PS/2 30–286, 50, 55SX, 60, 70, 70–
Supported Terminals (Continued) Terminal Telex 122 key USB PC Keyboard USB Mac Keyboard USB Com Port USB HIDPOS Wand Emulation (Code 39 Format) Wand Emulation (Same Code Format) Model(s) 078, 078A, 79, 80, 191, 196, 1191,1192, 1471, 1472, 1476, 1477, 1482, 1483 Terminal ID 046 124*** 125*** 130 131*** 061 064 * Default for 3800i/3800iSR050E models ** Default for 3800rSR030E model (applies to 3800rSR030E models only) ***Applies to 3800i/3800iSR050E model only.
Keyboard Country Scan the appropriate country code below to program the keyboard for your country.
Please refer to Hand Held Products website (www.handheld.com) for complete keyboard country support information and applicable interfaces. If you need to program a keyboard for a country other than one listed above, scan the Program Keyboard Country bar code below, then scan the numeric bar code(s) for the appropriate country from the inside back cover, then the Save bar code. Program Keyboard Country Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. Default = Regular.
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Emulate External Keyboard Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer. Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + ASCII Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F.
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters.
Connecting the Scanner with RS-232 Serial Port Note: These instructions are for use with the RS-232 power stealer cable. 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer. 5 2 3 4 3. Unplug the mouse or keyboard from the computer. Plug the mouse or keyboard into the power tap on the scanner cable. 4.
RS-232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 115,200.
RS-232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications which require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity. Default = None.
RS-232 Handshaking RS-232 handshaking is a set of rules concerning the exchange of data between serially communicating devices. Default = RTS/CTS, XON/XOFF and ACK/ NAK Off RTS/CTS On * RTS/CTS Off XON/XOFF On * XON/OFF Off ACK/NAK On * ACK/NAK Off Wand Emulation Connection The Wand Emulation Connection bar codes should be used if you want to change the terminal ID only, without changing any other imager settings.
Wand Emulation Transmission Rate The transmission rate is limited by the terminal’s ability to receive data without dropping characters. Default = 25 inches/second. 10 * 25 40 80 120 150 200 Wand Emulation Polarity The Polarity can be sent as standard with black bars high, or reversed with white bars high. Default = Black High.
Wand Emulation Idle The idle describes the state of the scanner when no data is being transmitted. When in Wand Emulation mode, you must set the scanner’s idle state to match the idle state for the device to which the scanner is connected. Default = Idle High. * Idle High Idle Low Wand Emulation Note: Changing primary wand emulation settings also changes the secondary wand emulation settings (see Secondary Code 39 Wand Emulation on page 6-2).
Delay Between Blocks Note: This option is not applicable to Laser Emulation Raw Output (see Secondary Laser Emulation on page 6-3). This sets the delay time between data blocks. Default = 50ms. 5ms * 50ms 150ms 500ms Overall Checksum Note: This option is not applicable to Laser Emulation Raw Output (see Secondary Laser Emulation on page 6-3). When this option is turned on, a computed check character is added at the end of the entire message.
3 Output Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = On. * On Off Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High for the 3800i, Medium for the 3800r.
Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On. * On Off Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read.
Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Default = No Delay. * No Delay Short Delay (500 ms) Medium Delay (1000 ms) Long Delay (1500 ms) User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
Read Time-Out Use this selection to set a time-out (in milliseconds) of the scanner’s trigger when using serial commands to trigger the scanner. Once the scanner has timed out, you can activate the scanner either by pressing the trigger or using a serial trigger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by scanning digits from the inside back cover, then scanning Save. Default = 300,000.
Presentation Mode Note: Presentation mode does not work when a scanner is programmed for the laser emulation interface. Note: If the Presentation Mode selection is enabled, the aimer beam option is disabled. The LEDs are off until a bar code is presented to the scanner. Then the LEDs turn on automatically to read the code. Presentation Mode uses ambient light to detect the bar codes. If the light level in the room is not high enough, Presentation Mode will not work properly.
Reread Delay only works when in automatic trigger mode (see page 3-4). Short (500 ms) * Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
Aimer Beam Delay (Aimer Beam option only) The Aimer Beam Delay allows a delay time for the operator to aim the reader before the standard illumination and decoding starts. The quickset codes sets the time between when the trigger is pulled and when the decode starts to either 1 or 2 seconds. During the delay time, the aiming beam appears, but the illumination LEDs won’t turn on until the delay time is over.
Aimer Beam Time-Out (Aimer Beam option only) Aimer Beam Time-Out powers down the aimer beam after a time-out if the trigger is still pulled and there isn’t a valid decode. Scan the bar code below, then set the time-out by scanning digits (from 0 - 240,000 ms) from the Programming Chart inside the back cover of this manual and then scan Save.
The figure below illustrates the percentage range from 1 to 100%. 40% 60% 30% 70% 80% 20% 90% 10% 0% 100% Example: If you have two bar codes next to one another and the centering window is set to 40% left edge and 60% right edge, only the bar code that intersects that window will be decoded.
Output Sequence Overview Require Output Sequence When turned off, the bar code data will be output to the host as the scanner decodes it. When turned on, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. Note: This selection is unavailable when the Multiple Symbols Selection is turned on.
Other Programming Selections •Discard This exits without saving any Output Sequence changes. Output Sequence Editor Enter Sequence Default Sequence Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device.
Note: Code 93 must be enabled to use this example.
The breakdown of the command line is shown below: SEQBLK 62 0011 41 FF 6A 0012 42 FF 69 0011 43 FF sequence editor start command code identifier for Code 39 Code 39 code length (9) plus CR suffix (2) = 11 start character match for Code 39, 41h = “A” termination string for first code code identifier for Code 128 Code 128 code length (10) plus CR suffix (2) = 12 start character match for Code 128, 42h = “B” termination string for second code code identifier for Code 93 Code 93 code length (9) plus CR suffix
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message using the Data Formatter (page 5-5). The hex code for the No Read symbol is 9C. Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. The “Off” bar code below is an example of this type of bar code. Note: If additional menuing is required, Video Reverse must be disabled to read the menu bar codes and then re-enabled after menuing is completed.
4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string. Prefix and Suffix characters are data characters that can be sent before and after scanned data.
To Add a Prefix or Suffix: Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-3). Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Appendix A) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Step 4.
To Clear One or All Prefixes or Suffixes: You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. When you Clear One Prefix (Suffix), the specific character you select is deleted from the symbology you want. When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted. Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2.
Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 8-3. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.
Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual. Prefix Scanned Data 1 2 3 4 Suffix 5 Intercharacter Delay Intercharacter Delay To remove this delay, scan the Intercharacter Delay bar code, then set the number of steps to 0.
Interfunction Delay An interfunction delay of up to 495 milliseconds may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual. Prefix STX 1 Scanned Data HT 2 3 4 5 Suffix CR LF Interfunction Delays Interfunction Delay To remove this delay, scan the Interfunction Delay bar code, then set the number of steps to 0.
5 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None.
inside back cover to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0 3 for an AT wedge. Note: The wildcard for all terminal types is 099. Step 4. Code I.D. In the Appendix A, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 5.
(00-99) for the number of characters and xx stands for the hex value for an ASCII code. See ASCII Conversion Chart (Code Page 1252) on page A-2.) F3 Send up to but not including “ss” character (Search and Send) starting from current cursor position, leaving cursor pointing to “ss” character followed by “xx” key or function code. Syntax = F3ssxx (ss and xx both stand for the hex values for ASCII codes, see ASCII Conversion Chart (Code Page 1252) on page A-2.
FC E4 E5 FE EC ED zz is the list of characters to be suppressed. (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A2.) Disables suppress filter and clear all suppressed characters. Syntax = FC. Replaces up to 15 characters in the data string with user specified characters. Replacement continues until the E5 command is encountered. Syntax = E4nnxx1xx2yy1yy2...
Data Formatter When Data Formatter is turned off, the bar code data is output to the host as read (including prefixes and suffixes). Choose one of the following options. Default = Data Formatter On. * Data Formatter On, but Not Required Data Formatter Off When Data Formatter is required, all input data must conform to an edited format or the scanner does not transmit the input data to the host device.
5-6 3800i/3800r User’s Guide
6 Secondary Interface By switching secondary interface cables, the 3800i/3800r scanner, for example, can communicate with a portable data terminal (secondary interface) in addition to the host terminal (primary interface). See the tables below for the secondary interfaces for each 3800i/3800r model. 3800i Models The chart below lists the 3800i scanner models. “SR” indicates “Standard Range” linear optics.
Enabling the Secondary Interface The secondary interface can be programmed at any time. You can temporarily disable the secondary interface, but still retain the secondary interface settings in the imager’s memory by scanning the Disable bar code below. To re-enable the secondary interface, scan the Enable bar code. Default =Disable.
Secondary Laser Emulation Use this selection when connecting to a secondary terminal with integral decoding. This also sets the transmission rate to 36 scans per second, the polarity to white high, and deletes all prefixes and suffixes. * Laser Emulation Same Code Output When you scan the following bar code, the imager sends the raw data edges to the host for host decoding. This also sets the transmission rate to 36 scans per second and the polarity to white high.
Laser Emulation Polarity The Polarity can be sent as standard with white bars high, or reversed with black bars high. Default = White High. * White High Black High Laser Emulation Idle The idle describes the state of the scanner when no data is being transmitted. When in Non Decoded mode, you must set the scanner’s idle state to match the idle state for the device to which the scanner is connected. Default = Idle High.
Manual Trigger, Low Power: Scan the Manual Trigger, Low Power bar code below and the scanner “sleeps” until the trigger is pulled. When the trigger is pulled, the scanner wakes up and operates at normal power until there is no triggering for the time set with the Low Power Time-Out bar code. Then, the scanner goes to “sleep” again. Manual Trigger, Low Power Low Power Time-Out: Scan the Low Power Time-Out bar code to change the time-out duration.
6-6 3800i/3800r User’s Guide
7 Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 11 for settings and defaults.
Message Length You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code doesn’t match the valid reading length, the scanner will issue an error beep. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread. EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09 Max.
Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar codes with Modulo 16 check characters. Default = No Check Character.
Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted. Default = On. Character Start Stop Start Stop Codabar A12D D34A Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion.
Code 39 < Default All Code 39 Settings > Code 39 * On Off Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit.
Code 39 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check character, but will not transmit the check character with the scanned data.
Code 39 Append This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 39 bar codes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the order in which the bar codes are read, deleting the first space from each.
Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.
Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.
Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 Code Page Code pages define the mapping of character codes to characters.
Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On * Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Straight 2 of 5 IATA On * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 11 Code 11 On * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.
Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 Code 128 * On Off ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner.
Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 Code Page Code pages define the mapping of character codes to characters.
Telepen On * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output. * AIM Telepen Output Original Telepen Output Telepen Message Length Scan the bar codes below to change the message length.
UPC A UPC A * On Off UPC A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off UPC A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On.
UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off UPC A Addenda Required When Addenda Required is set to on, the scanner will only read UPC A bar codes that have addenda. Default = Not Required.
UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. Default = On. * On Off UPC E UPC E0 and UPC E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number system, use the UPC E1 selection. Default = Off (UPC E0) and Off (UPC E1).
UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off. On * Off UPC E0 and UPC E1 Addenda Required When Addenda Required is set to on, the scanner will only read UPC E bar codes that have addenda. Default = Not Required. Required * Not Required UPC E0 and UPC E1 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On.
UPC E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data. Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN 13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off EAN/JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN 13 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code on page 7-20. ISBN Translate This selection causes EAN-13 Bookland symbols to be translated into their equivalent ISBN number format. Default = Off.
EAN/JAN 8 * On Off EAN/JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On Off EAN/JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Default = Off for both 2 Digit and 5 Digit Addenda.
When Addenda Required is set to on, the scanner will only read EAN/JAN 8 bar codes that have addenda. Default = Not Required. Required * Not Required EAN/JAN 8 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off MSI MSI On * Off MSI Check Character Different types of check characters are used with MSI bar codes.
When Check Character is set to Validate and Transmit, the scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data. When Check Character is set to Validate, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character, but will not transmit the check character with the scanned data.
Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
RSS Limited < Default All RSS Limited Settings > RSS Limited * On Off RSS Expanded < Default All RSS Expanded Settings > RSS Expanded * On Off 3800i/3800r User’s Guide 7 - 29
RSS Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. Minimum Message Length Maximum Message Length EAN•UCC Emulation The imager can automatically format the output from any EAN•UCC data carrier to emulate what would be encoded in an equivalent UCC/EAN-128 or RSS+Composite symbol.
China Post Code On * Off China Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length PosiCode PosiCode A and B * On Off You have to have PosiCode A and B on to read any of the PosiCode symbologies.
PosiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Trioptic Code Trioptic Code is used for labeling magnetic storage media. Note: If you are going to scan Code 32 Pharmaceutical codes, Trioptic Code must be off.
Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048. Minimum Message Length Maximum Message Length Code 16K Code 16K On * Off Code 16K Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information.
Code 49 Code 49 * On Off Code 49 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 7-2 for additional information. Minimum and Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81.
7 - 36 3800i/3800r User’s Guide
8 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-6 enable Control + ASCII mode.
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Country Codes United States [ \ ] 6 - Belgium [ < ] 6 - Scandinavia 8 < 9 6 - France ^ 8 $ 6 = Germany à + 6 - Italy \ + 6 - Switzerland < ..
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM AT/XT and PS/2 Compatibles, WYSE PC/AT Supported Keys Reserved Enter (KP) Cap Lock ALT make ALT break CTRL make CTRL break CR/Enter Reserved Tab Reserved Tab Delete CR/Enter Insert Escape F11 Home Print Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM, Memorex Telex (102)* Supported Keys Reserved Enter F11 F12 F13 F14 F15 New Line F16 F17 F18 Tab/Field Forward Delete Field Exit Insert Clear Error Reset Home Print Back Space Back Tab F19 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 Memorex Telex (88)** Supported Keys Res
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F Esprit 200, 400 ANSI Supported Keys Reserved New Line N/A N/A N/A N/A N/A New Line N/A Tab N/A Tab N/A New Line N/A Escape F11 Insert F13 Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 3800i/3800r User’s Guide Esprit 200, 400 ASCII Supported Keys Reserv
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US DEL 8-6 HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 7F Apple Mac/iMac Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make TAB APPLE break TAB Del RETURN Ins Help ESC F11 Home Prnt Scrn BACKSPACE LSHIFT TAB F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 BACKSPACE
9 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, included in the Appendix A, page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power cycled. Add Code I.D.
Temporary Visual Xpress Configuration For quick download communication configuration, scan the Visual Xpress bar code to temporarily configure the imager for Visual Xpress settings. Refer to Visual Xpress on page 10-1 for additional information about Visual Xpress. Note: Connect the imager using RS-232 cables. Scan the bar code below and the unit will communicate in RS-232 mode, allowing it to work with Visual Xpress. The imager reverts to the original or reprogrammed interface when the power is cycled.
10 Visual Xpress Visual Xpress Introduction Visual Xpress provides a wide range of PC-based programming functions that can be performed on an imager connected to your PC's COM port. Visual Xpress allows you to download upgrades to the imager's firmware, change programmed parameters, and create and print programming bar codes. Using Visual Xpress, you can even save/open the programming parameters for an imager.
Installing Visual Xpress from the Web 1. Access the Hand Held Products web site at www.handheld.com. 2. Click in the Quick Search text box and enter Visual Xpress. 3. Click on Search Now. 4. Click on the entry for Visual Xpress. 5. When prompted, select Save File, and save the files to the c:\windows\temp directory. 6. Once you have finished downloading the file, exit the web site. 7. Using Explorer, go to the c:\windows\temp file and unzip the file you saved. 8. Double click on Setup.
11 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the 3800i/3800r. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an RS-232 interface (see page 1-8). The following commands can be sent via a PC com port using terminal emulation software.
Query Commands Several special characters can be used to query the device about its settings. ^ ? * What is the default value for the setting(s). What is the device’s current value for the setting(s). What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a continuous range of values. A pipe (|) separates items in a list of non-continuous values.
When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command. Examples of Query Commands In the following examples, a bracketed notation [ ] depicts a non-displayable response. Example: Enter: Response: Example #1:What is the range of possible values for Codabar Coding Enable? cbrena*.
Trigger Commands You can activate and deactivate the scanner with serial trigger commands. First, the scanner must be put in Manual/Serial Trigger Mode either by scanning the Manual/Serial Trigger Mode bar code (page 3-3), or by sending the Manual/ Serial Menu Command (page 11-8).
Menu Commands Selection Factory Default Settings Setting Serial Command * Indicates default # Indicates a numeric entry Default DEFALT 003 (3800i/3800rSR050E models) 000 (3800iSR030E and 3800iSR000E models) TERMID### Page Terminal Interfaces Terminal ID Program Keyboard Country Keyboard Style Keyboard Modifiers Serial Port Connection 3800i/3800r User’s Guide 2-2 *USA KBDCTY0 2-4 Belgium KBDCTY1 2-4 Denmark KBDCTY8 2-4 Finland KBDCTY2 2-4 France KBDCTY3 2-4 Germany/Austria K
Selection Baud Rate Word Length: Data Bits, Stop Bits, and Parity RS-232 Handshaking Wand Emulation Connection 11 - 6 Setting Serial Command Page * Indicates default # Indicates a numeric entry 300 BPS 232BAD0 2-9 600 BPS 232BAD1 2-9 1200 BPS 232BAD2 2-9 2400 BPS 232BAD3 2-9 4800 BPS 232BAD4 2-9 9600 BPS 232BAD5 2-9 19200 BPS 232BAD6 2-9 38400 BPS 232BAD7 2-9 57600 BPS 232BAD8 2-9 *115200 BPS 232BAD9 2-9 7 Data, 1 Stop, Parity Even 232WRD3 2-10 7 Data, 1 Stop, Par
Selection Wand Emulation Transmission Rate Wand Emulation Polarity Wand Emulation Idle Wand Emulation Data Block Size Wand Emulation Delay Between Blocks Wand Emulation Overall Checksum Setting * Indicates default Serial Command # Indicates a numeric entry Page 10 WNDSPD0 2-12 *25 WNDSPD1 2-12 40 WNDSPD2 2-12 80 WNDSPD3 2-12 120 WNDSPD4 2-12 150 WNDSPD5 2-12 200 WNDSPD6 2-12 *Black High WNDPOL0 2-12 White High WNDPOL1 2-12 Idle Low WNDIDL0 2-13 *Idle High WNDIDL1 2-
Selection Beeper Duration - Good Read LED - Good Read Number of Beeps - Good Read Good Read Delay User-Specified Good Read Delay Trigger Mode Reread Delay User-Specified Reread Delay Aimer Delay Aimer Mode 11 - 8 Setting Serial Command Page * Indicates default # Indicates a numeric entry *Normal Beep BEPBIP0 Short Beep BEPBIP1 3-2 Off BEPLED0 3-2 3-2 *On BEPLED1 3-2 *1 BEPRPT1 3-2 Range 1 - 9 BEPRPT# 3-2 *No Delay DLYGRD0 3-3 Short Delay (500 ms) DLYGRD500 3-3 Medium D
Selection Aimer Beam Time-Out Centering Output Sequence Editor Require Output Sequence Multiple Symbols No Read Video Reverse Setting Serial Command Page * Indicates default # Indicates a numeric entry Time-Out Duration (0 240,000 ms) *0 SCNADR#### ## 3-8 Centering On DECWIN1 3-8 *Centering Off DECWIN0 3-8 Left of Centering Window *40 DECLFT### 3-8 Right of Centering Window *60 DECRGT### 3-8 Enter Sequence SEQBLK 3-11 Default Sequence SEQDFT 3-11 Required SEQ_EN2 3-11 On
Selection Serial Command Setting * Indicates default # Indicates a numeric entry Page Data Formatter Selections Data Format Editor Data Formatter Alternate Data Formats *Default Data Format (None) DFMDF3 5-4 Enter Data Format DFMBK3## 5-4 Clear One Data Format DFMCL3 5-4 Clear All Data Formats DFMCA3 5-4 Off DFM_EN0 5-5 *On, but Not Required DFM_EN1 5-5 On, Required DFM_EN2 5-5 1 VSAF_1 5-5 2 VSAF_2 5-5 3 VSAF_3 5-5 *Disable 2IF_EN0 6-2 Enable 2IF_EN1 6-2 RS-232 I
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Symbologies All Symbologies Codabar Codabar Codabar Start/Stop Char. Codabar Check Char. Codabar Concatenation Codabar Message Length Code 39 Code 39 Code 39 Start/Stop Char. Code 39 Check Char.
Selection Code 39 Full ASCII Interleaved 2 of 5 Serial Command Setting Page * Indicates default # Indicates a numeric entry *Off C39ASC0 7-8 On C39ASC1 7-8 Default All Interleaved 2 of 5 Settings I25DFT 7-9 Off I25ENA0 7-9 *On I25ENA1 7-9 *No Check Char.
Selection Matrix 2 of 5 Message Length Code 11 Code 11 Code 11 Check Digits Required Code 11 Message Length Code 128 Code 128 ISBT Concatenation Setting Serial Command Page * Indicates default # Indicates a numeric entry Minimum (1 - 80) *4 X25MIN## 7-14 Maximum (1 - 80) *80 X25MAX## 7-14 Default All Code 11 Settings C11DFT 7-14 *Off C11ENA0 7-14 On C11ENA1 7-14 1 Check Digit C11CK20 7-14 *2 Check Digits C11CK21 7-14 Minimum (1 - 80) *4 C11MIN## 7-15 Maximum (1 - 80) *80 C11
Selection UPC A UPC A Check Digit UPC A Number System UPC A 2 Digit Addenda UPC A 5 Digit Addenda UPC A Addenda Required UPC A Addenda Separator UPC E UPC E0 UPC E1 UPC E Expand UPC E Check Digit UPC E Number System UPC E 2 Digit Addenda UPC E 5 Digit Addenda UPC E Addenda Required UPC E Addenda Separator 11 - 14 Setting Serial Command Page * Indicates default # Indicates a numeric entry Off UPAENA0 *On UPAENA1 7-18 Off UPACKX0 7-18 7-18 *On UPACKX1 7-18 Off UPANSX0 7-18 *
Selection EAN/JAN 13 EAN/JAN 13 Setting * Indicates default Serial Command # Indicates a numeric entry Page Default All EAN/ JAN 13 Settings E13DFT 7-22 Off E13ENA0 7-22 *On E13ENA1 7-22 Off E13CKX0 7-23 *On E13CKX1 7-22 EAN/JAN 13 2 Digit Addenda *Off E13AD20 7-23 On E13AD21 7-23 EAN/JAN 13 5 Digit Addenda *Off E13AD50 7-23 On E13AD51 7-23 EAN/JAN 13 Addenda Required *Not Required E13ARQ0 7-23 Required E13ARQ1 7-23 EAN/JAN 13 Addenda Separator Off E13ADS0 7-24 *
Selection MSI MSI Check Character MSI Message Length Plessey Code Plessey Code Plessey Message Length RSS-14 RSS-14 RSS Limited RSS Limited RSS Expanded RSS Expanded RSS Expanded Msg.
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Minimum (2 - 80) *4 CPCMIN## 7-31 Maximum (2 - 80) *80 CPCMAX## 7-31 Default All Korea Post Code Settings KPCDFT 7-31 *Off KPCENA0 7-31 On KPCENA1 7-31 Korea Post Code Msg.
11 - 18 3800i/3800r User’s Guide
12 Product Specifications 3800r Product Specifications Parameter Specification Dimensions (Typical): Height 6.2 inches (15.7 cm) Length 5.3 inches (13.5 cm) Width 3.2 inches (8.1 cm) Weight 6.5 ounces (185 g) Light Source 630 nM visible red LED Scan Rate 270 scans per second in most usages Skew Angle ±65 degrees Pitch Angle ±65 degrees Horizontal Velocity 2 inches (5 cm) per second Scan Contrast 20% minimum Voltage Requirements 4.
3800r Depth of Field Minimum Bar Width Maximum Near Field Minimum Far Field (no ambient lighting) 13 mil 100% UPC 1 in (2.5 cm) 24 in (61 cm) 7.5 mil Code 39 4 in (10 cm) 14 in (36 cm) 10 mil Code 39 2 in (5 cm) 18 in (46 cm) 13 mil Code 39 1 in (2.5 cm) 24 in (61 cm) 15 mil Code 39 1 in (2.5 cm) 28 in (71 cm) 20 mil Code 39 1 in (2.5 cm) 36 in (91 cm) 55 mil Code 39 4 in (10.
3800i Product Specifications Parameter Specification Dimensions (Typical): without aimer with aimer Height 6.4 inches (16.3 cm) 6.5 inches (16.5 cm) Length 5.3 inches (13.5 cm) 5.3 inches (13.5 cm) Width 3.2 inches (8.1 cm) 3.2 inches (8.1 cm) Weight 7.5 ounces (213 g) 8.4 oz. (238 g) Light Source 630 nm visible red LED Aimer Beam Light Source Class 2 Laser Product, 1.
3800i Depth of Field Min. Bar Width Max. Near Field Min. Far Field Min. Far Field (25 Lux lighting) (300 Lux lighting) 13 mil 100% UPC 2.5 in (6.4 cm) 26 in (66 cm) 28 in (71 cm) 7.5 mil Code 39 6.5 in (16.5 cm) 14 in (36 cm) 15 in (38 cm) 15 mil Code 39 2.5 in (6.4 cm) 30 in (76.2 cm) 31 in (78.7 cm) 20 mil Code 39 1.5 in (3.8 cm) 39 in (99.1 cm) 42 in (107 cm) 55 mil Code 39 4 in (10.
3800i/3800r User’s Guide Turn on good read or LED beeper 2 Trigger signal to decoder 3 Laser enable 4 Supply ground 5 6 Digital bar code data output 7 Supply input power (Refer to tables on page 12-1 and page 12-3) 8 9 Start of scan 10 1 9 5 Volt power connection ◆ 8 Cord shield 6 Laser enable 7 Supply ground Conventional laser data format is provided at the modular connector in the scanner handle.
12 - 6 2 Cord shield 3 Tied to supply power 4 Supply ground 5 Terminal clock 6 Terminal data 7 Supply power input (Refer to tables on page 12-1 and page 12-3) 8 Keyboard data 9 Keyboard clock 10 1 connects to the scanner handle 10 Pin RJ41 Modular Plug Standard Cable Pinouts Keyboard Wedge 3800i/3800r User’s Guide
3800i/3800r User’s Guide connects to your terminal 10 Pin Modular Plug connects to the scanner handle 9 Pin Type D Female 1 9 8 7 6 Supply ground Cord shield 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 6 Bar code data output 7 Supply power input (Refer to tables on page 12-1 and page 12-3) 8 9 10 1 5 Supply power input 4 3 Bar code data output 2 Standard Cable Pinouts Wand Emulation 12 - 7
12 - 8 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 Receive data - Serial data to scanner 6 Transmit data - Serial data from scanner 7 Supply power input (Refer to tables on page 12-1 and page 12-3) 8 Request to send data 9 Clear to send data 10 1 connects to the scanner handle 10 Pin RJ41 Modular Plug Standard Cable Pinouts Serial Output 3800i/3800r User’s Guide
3800i/3800r User’s Guide 10 Pin Modular Plug connects to the scanner handle 1 2 Data + 3 Tied to supply power 4 Supply ground 5 6 7 5 volt supply power input 8 9 10 Data - Standard Cable Pinouts USB 12 - 9
12 - 10 3800i/3800r User’s Guide
13 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center. Please see Customer Support on page 14-1 for further information. Maintenance The 3800i/3800r provides reliable and efficient operation with a minimum of care.
Replacing the Interface Cable The standard interface cable is attached to the scanner with an 10-pin modular connector. When properly seated, the connector is held in the 3800i/3800r scanner’s handle by a flexible retention tab. The interface cable is designed to be field replaceable. • Order replacement cables from Hand Held Products or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.
To Replace the 3800i Interface Cable: 1. Turn the power to the host system OFF. 2. Disconnect the imager’s cable from the terminal or computer. 3. Use a screwdriver to unscrew the cord lock from the base of the imager if in use. 4. Locate the small hole on the side of the imager’s handle. This is the cable release. Cable Release 5. Straighten one end of a paper clip. 6. Insert the end of the paper clip into the small hole and press in. This depresses the retention tab, releasing the connector.
• Are enabled in the scanner or in the decoder to which the scanner connects. Is the bar code displayed but not entered? The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example). You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application.
14 Customer Support Product Service and Repair Hand Held Products provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, return the unit to Hand Held Products (postage paid) with a copy of the dated purchase record attached. Contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.
Online Product Service and Repair Assistance You can also access product service and repair assistance online at www.handheld.com. Technical Assistance If you need assistance installing or troubleshooting your scanner, please call your Distributor or the nearest Hand Held Products technical support office: North America/Canada: Telephone: Fax number: E-mail: (800) 782-4263, option 4 (8 a.m. to 6 p.m. EST) (315) 685-4960 natechsupport@handheld.
This warranty shall extend from the time of shipment for the duration published by Hand Held Products for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to Hand Held Products’ factory or authorized service center for inspection. No product will be accepted by Hand Held Products without a Return Materials Authorization, which may be obtained by contacting Hand Held Products.
14 - 4 3800i/3800r User’s Guide
Appendix A Symbology Chart Symbology Code AIM ID ID Hex ID Symbology Code AIM ID ID Hex ID China Post Q ]X0 51 Straight 2 of 5 IATA f ]Rm 66 Codabar a ]Fm 61 Interleaved 2 of 5 e ]lm 65 Codablock F q ]Om 71 Korea Post ? ]X0 3F Straight 2 of 5 Industrial f ]Rm 66 Matrix 2 of 5 m ]X0 6D g ]Mm Code 11 h ]Hm 68 MSI Code 16K o ]Km 6F No Read Code 39 b ]Am 62 Plessey Code n ]P0 6E Code 32 Pharmaceutical (PARAF) < ]X0 3C PosiCode W ]pm 57 l ]Tm 6C
ASCII Conversion Chart (Code Page 1252) Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
Dec Hex Char Dec Hex Char Dec Hex 160 A0 192 C0 À 224 E0 à 161 A1 ¡ 193 C1 Á 225 E1 á 162 A2 ¢ 194 C2 Â 226 E2 â ƒ 163 A3 £ 195 C3 Ã 227 E3 ã 84 „ 164 A4 ¤ 196 C4 Ä 228 E4 ä 85 … 165 A5 ¥ 197 C5 Å 229 E5 å 134 86 † 166 A6 ¦ 198 C6 Æ 230 E6 æ 135 87 ‡ 167 A7 § 199 C7 Ç 231 E7 ç 136 88 ˆ 168 A8 ¨ 200 C8 È 232 E8 è 137 89 ‰ 169 A9 © 201 C9 É 233 E9 é 138 8A Š 170 AA ª 202 CA Ê 234 EA ê 1
Code Page Mapping of Printed Bar Codes Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, select the code page with which the bar codes were created. The data characters should then appear properly. Note: The Code Page option is available for Code 39, Code 93, and Code 128.
Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN 13 EAN 8 9 780330 290951 654 3210 5 UPC-E 0 456123 8
Sample Symbols Code 39 BC321 Code 93 123456-9$ Matrix 2 of 5 6543210 Codabar A13579B Straight 2 of 5 Industrial 123456 RSS-14 (01)00123456789012
Programming Chart 0 1 2 3 4 5 6 7 8 9 A B C D E F Discard Note: Save If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save.
Hand Held Products, Inc. 700 Visions Drive P.O.