40003916 Installation Instructions

ManualsBrandsHoneywell ManualsMiscellaneous24V, 50/60 Hz Replacement Head for V8044B

Table Of Contents

INSTALLATION INSTRUCTIONS

Put Bar Code Here

95C-10655—05

40003916 Replacement Powerhead

APPLICATION

The 40003916 replacement heads are for field replacement of

heads in Honeywell diverting and straight through motorised

valves. They can be used to replace the valve heads

removable without draining the system and also valves which

require draining the system. A head which does not require

the system to be drained is identified by a small round bump

on the cover and the “6” or higher suffix number after the OS

number. Also only two screws and two locating pegs are used

to connect the heads to the body.

For older style heads which require the system to be drained,

an adaptor kit 40003918-006 must be used with the 40003916

head.

SPECIFICATIONS

Voltage: 230V ~ 50Hz

Power Consumption: 6W (0.04)

Lead Supplied: 1 metre

Operating Temperature Range: +5 to +88° C

Maximum Ambient Temperature: +52° C

*Replacement head 40003916-001 has 6 core flying lead.

When used with V4043H1056/V4043H1007 series valves, the

white wire must be electrically isolated.

INSTALLATION

REMOVING OLD STYLE HEAD FROM OLD STYLE BODY

CAUTION

It is not necessary to remove the valve body from

the pipeline but the system must be drained of

water before removing the old valve unless

isolating valves have been fitted.

This product MUST be installed by a competent person. The

installation MUST conform to I.E.E. Regulations and with The

Electricity at Work Regulations.

Fig. 1. Removing Cover

Zone Valve

Replacement

Head Number

Adaptor Kit

Number

V4043H1007 40003916-001* 40003918-006

V4043H1056 40003916-001* 40003918-006

V4043H1080 40003916-001 40003918-006

V4043H1106 40003916-001 40003918-006

V4044C1288 40003916-002 40003918-007

V4044C1098 40003916-002 40003918-007

Summary of content (4 pages)

PAGE 1
40003916 Replacement Powerhead INSTALLATION INSTRUCTIONS APPLICATION The 40003916 replacement heads are for field replacement of heads in Honeywell diverting and straight through motorised valves. They can be used to replace the valve heads removable without draining the system and also valves which require draining the system. A head which does not require the system to be drained is identified by a small round bump on the cover and the “6” or higher suffix number after the OS number.
PAGE 2
40003916 REPLACEMENT POWERHEAD 1. 2. 3. 4. INSTALLING REPLACEMENT HEAD ON OLD STYLE VALVE BODY (REQUIRES THE ADAPTOR KIT) 1. Insert the new O-ring (supplied with the Adaptor Kit) into the circular slot on top of the valve body. (See Fig. 3A.) 2. Place the adaptor on the valve body and secure it with the four hex-nut screws provided - ensuring that the three guide pins engage in their mating recesses. 3. Place the manual operating lever of the replacement head in the “MAN.
PAGE 3
40003916 REPLACEMENT POWERHEAD OPERATION Whilst Honeywell takes all practicable steps to design and manufacture its products to comply with the requirements of the Heath and Safety at Work Act 1974, all products must be properly used and Purchasers are reminded that their obligations under the Act are to ensure that the installation and operation of such products at a place of work should be safe and without risk to them.
PAGE 4
0003916 REPLACEMENT POWERHEAD Honeywell Control Systems Ltd. Arlington Business Park Bracknell, Berkshire RG12 1EB Technical help desk: 08457 678999 www.honeywelluk.com ® U.S. Registered Trademark © 2012 Honeywell International Inc. 95C-10665—05 K.K. Rev.