4600g, 4600r, 4600rp, 4800i Quick Start Guide
Note: Refer to your user’s guide for information about cleaning your device. For localized language versions of this document, go to www.honeywell.com/aidc. Getting Started Turn off computer’s power before connecting the scanner, then power up the computer once the scanner is fully connected.
Keyboard Wedge Connection Serial (RS-232) Connection 2
Reading Techniques The view finder projects an aiming beam that should be centered over the barcode, but can be positioned in any direction for a good read. Hold the scanner over the barcode, pull the trigger, and center the aiming beam on the barcode. The aiming beam is smaller when the scanner is closer to the code and larger when it is farther from the code. Hold the scanner close to smaller barcodes, and farther away from large barcodes to get a proper read. If the barcode is highly reflective (e.g.
Interface Scan the barcode that describes the PC or interface you are using.
Keyboard Country Scan the Program Keyboard Country barcode below, then scan the numeric barcode(s) from page 10, then the Save barcode to program the keyboard for your country. As a general rule, the following characters are not supported by the scanner for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~.
Trigger The following barcodes will allow you to use the reader in Manual Trigger mode (need to press the trigger to read) or Presentation mode (the reader is activated when it “sees” a barcode). Manual Trigger (Default) Presentation Mode Streaming Presentation™ Note: Streaming Presentation Mode applies only to units with the Advanced Illumination feature. Units with the advanced illumination feature have a software revision of 31205480-118 or newer.
Reread Delay This sets the time period before the scanner can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same barcode. Medium Reread Delay Suffix If you want a carriage return after the barcode, scan the Add CR Suffix barcode. To add a tab after the barcode, scan the Add Tab Suffix barcode. Otherwise, scan the Remove Suffix barcode to remove the suffixes.
Add Code ID Prefix to all Symbologies Scan the following barcode if you wish to add a Code ID prefix to all symbologies at once. Add Code ID Prefix To All Symbologies (Temporary) Note: For a complete list of Code IDs, see the User’s Guide for your product at our website, www.honeywell.com/aidc. Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the imager transmits the function code to the terminal.
Data Format Editor Instructions The following are abbreviated instructions for entering a data format. For complete instructions refer to your User’s Guide, available at our website, www.honeywell.com/aidc. 1. Scan the Enter Data Format symbol. 2. Primary/Alternate Format: scan 0 for Primary Format 3. Terminal Type: scan 099 for any terminal type 4. Code I.D.: scan 99 for any barcode type 5. Length: scan 9999 for any length barcode. 6. Editor commands: use the Programming Chart that follows. 7.
Programming Chart 0 1 2 3 4 5 6 7 10
8 9 A B C D E F Save 11
Visual Xpress™ To obtain access to additional features for the imager, use Visual Xpress, available from our website at www.honeywell.com/aidc. For complete download instructions and descriptions of Visual Xpress features, refer to your User’s Guide. Technical Assistance If you need assistance installing or troubleshooting your device, please call your distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263 (8 a.m. to 6 p.m.
Asia Pacific Telephone - Hong Kong: +852-3188-3485 or 2511-3050 Telephone - China: +86 21 6361 3818 E-mail: aptechsupport@honeywell.com Japan Telephone: +813 5770-6312 E-mail: aptechsupport@honeywell.com Malaysia Telephone: +603-6201-7020 E-mail: aptechsupport@honeywell.com Online Technical Assistance You can also access technical assistance online at www.honeywell.com/aidc. For Further Information To download the full User’s Guide for these products, visit our website at www.honeywell.com/ aidc.
North America Telephone: (800) 782-4263 Fax: (803) 835-8012 E-mail: naservice@honeywell.com Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 Fax: (239) 263-9689 E-mail: laservice@honeywell.com Brazil Telephone: +55 (21) 3535-9100 Fax: +55 (21) 3535-9105 E-mail: brservice@honeywell.com Mexico Telephone: +52 (55) 5203-2100 Fax: +52 (55) 5531-3672 E-mail: mxservice@honeywell.com Europe, Middle East, and Africa Telephone: +31 (0) 40 2901 633 Fax: +31 (0) 40 2901 631 E-mail: euservice@honeywell.
Online Product Service and Repair Assistance You can also access product service and repair assistance online at www.honeywell.com/aidc. Limited Warranty Honeywell International Inc. ("Honeywell") warrants its products to be free from defects in materials and workmanship and to conform to Honeywell’s published specifications applicable to the products purchased at the time of shipment.
This warranty shall extend from the time of shipment for the duration published by Honeywell for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to Honeywell factory or authorized service center for inspection. No product will be accepted by Honeywell without a Return Materials Authorization, which may be obtained by contacting Honeywell.
HONEYWELL’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS.
Disclaimer Honeywell International Inc. (“Honeywell”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Honeywell to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Honeywell.
Honeywell 700 Visions Drive P.O.
