Home Security System User Manual
Table Of Contents
- ONYX®FirstVision™
- Fire Alarm System Limitations
- Installation Precautions
- FCC Warning
- Section 1 Introduction
- Section 2 FirstVision Installation Instructions
- Section 3 Enabling FirstVision to Monitor Your Building
- 3.1 Process Overview
- 3.2 Make Connections to FirstVision
- 3.3 Turn on Power to FirstVision
- 3.4 Set the FirstVision Clock and Time Zone
- 3.5 Establish Communication Between Your LAN and FirstVision
- 3.6 Establish Gateway Communication
- 3.7 Copy Your Exported Building Design to FirstVision
- 3.8 Display Your Building Design on FirstVision
- 3.9 Test Your Building Design on FirstVision
- 3.10 Touch Screen Calibration
- Section 4 Operating Basics of FirstVision
- 4.1 Normal Operation (No Events Being Reported)
- Figure 4.1 FirstVision Display Example: No Alarms
- Figure 4.2 FirstVision Display Example: Floor Number Button
- Figure 4.3 FirstVision Display Example: Building Information
- Figure 4.4 FirstVision Display Example: Zoomed Floor Plan
- Figure 4.5 FirstVision Display Example: Moving Through a Zoomed Floor Plan
- Figure 4.6 FirstVision Display Example: HAZMAT Information
- 4.2 Investigating Gateway Disconnection
- 4.3 Operation When a Fire Alarm is Received
- 4.4 Operation After a Fire Alarm Has Been Cleared
- 4.5 Accessing the Log File
- 4.1 Normal Operation (No Events Being Reported)
- Section 5 The Development of FirstVision
- 5.1 The Current Situation for a Firefighter
- 5.2 The Technology of FirstVision
- 5.3 Expected Firefighter Interaction with the FirstVision
- 5.3.1 Example Emergency Situations
- Figure 5.1 Fire Scene Scenario Floor Plan Information
- Figure 5.2 Fire Scene Scenario Roof Plan Information
- Figure 5.3 Fire Scene Scenario HAZMAT Information
- Figure 5.4 Fire Scene Scenario Building Information
- Figure 5.5 Example Building Site Plan Information
- Figure 5.6 Example HAZMAT Information
- Figure 5.7 Example Contact Information
- 5.3.1 Example Emergency Situations
- Index
Introduction Agency Approvals
8 FIRSTVISION™ Installation and Operation Manual - P/N: 53034:Rev: A2 10/29/07
1.2.3 Ordering Information
Please verify part numbers with your sales representative before and when you are ordering.
1.3 Agency Approvals
FIRSTVISION has been designed to comply with standards set forth by the following regulatory
agencies. Before proceeding, the installer should be familiar with the following documents:
NFPA Standards
• National Fire Protection Association Standards 72.
• National Electric Code (NFPA 70).
Underwriters Laboratories U.S. Documents
• UL-864 Control Units and Accessories for Fire Alarm Systems.
Underwriters Laboratories Canada Documents
• CAN/ULC-S524-91 Standard for Installation of Fire Alarm Systems.
• CAN/ULC-S527-99 Standard for Control Units for Fire Alarm Systems.
Other
• Requirements of the Local Authority Having Jurisdiction (LAHJ).
1.3.1 Environmental Conditions
FIRSTVISION must be installed in the following environmental conditions:
• Temperature range of 0ºC - 50ºC (32ºF - 120ºF).
• 10-95% humidity non-condensing at 30ºC (86ºF).
Part Number Description
FIRSTVISION-ENC Enclosure
FIRSTVISION-LCD Liquid Crystal Display (LCD)
!
WARNING:
Improper installation, maintenance, and lack of routine testing could result in system malfunction.
!
WARNING: Wiring
It is recommended that the installer conform to local code requirements when installing all wiring. All
power connections must be non-resettable.