Home Security System User Manual
Table Of Contents
- ONYX®FirstVision™
- Fire Alarm System Limitations
- Installation Precautions
- FCC Warning
- Section 1 Introduction
- Section 2 FirstVision Installation Instructions
- Section 3 Enabling FirstVision to Monitor Your Building
- 3.1 Process Overview
- 3.2 Make Connections to FirstVision
- 3.3 Turn on Power to FirstVision
- 3.4 Set the FirstVision Clock and Time Zone
- 3.5 Establish Communication Between Your LAN and FirstVision
- 3.6 Establish Gateway Communication
- 3.7 Copy Your Exported Building Design to FirstVision
- 3.8 Display Your Building Design on FirstVision
- 3.9 Test Your Building Design on FirstVision
- 3.10 Touch Screen Calibration
- Section 4 Operating Basics of FirstVision
- 4.1 Normal Operation (No Events Being Reported)
- Figure 4.1 FirstVision Display Example: No Alarms
- Figure 4.2 FirstVision Display Example: Floor Number Button
- Figure 4.3 FirstVision Display Example: Building Information
- Figure 4.4 FirstVision Display Example: Zoomed Floor Plan
- Figure 4.5 FirstVision Display Example: Moving Through a Zoomed Floor Plan
- Figure 4.6 FirstVision Display Example: HAZMAT Information
- 4.2 Investigating Gateway Disconnection
- 4.3 Operation When a Fire Alarm is Received
- 4.4 Operation After a Fire Alarm Has Been Cleared
- 4.5 Accessing the Log File
- 4.1 Normal Operation (No Events Being Reported)
- Section 5 The Development of FirstVision
- 5.1 The Current Situation for a Firefighter
- 5.2 The Technology of FirstVision
- 5.3 Expected Firefighter Interaction with the FirstVision
- 5.3.1 Example Emergency Situations
- Figure 5.1 Fire Scene Scenario Floor Plan Information
- Figure 5.2 Fire Scene Scenario Roof Plan Information
- Figure 5.3 Fire Scene Scenario HAZMAT Information
- Figure 5.4 Fire Scene Scenario Building Information
- Figure 5.5 Example Building Site Plan Information
- Figure 5.6 Example HAZMAT Information
- Figure 5.7 Example Contact Information
- 5.3.1 Example Emergency Situations
- Index
Establish Gateway Communication Enabling FIRSTVISION to Monitor Your Building
23FIRSTVISION™ Installation and Operation Manual - P/N: 53034:Rev: A2 10/29/07
Step 6. Select the “Use the following IP address” radio button.
The “Obtain an IP address automatically” can NOT be used.
Step 7. Type in your IP address information on the Internet Protocol (TCP/IP) Properties window
(example only shown, the address is dependent on your network).
Figure 3.12 Windows Internet Protocol Properties
Step 8. Confirm that is 255.255.255.0 in the Subnet Mask field to choose the internal network (the
address is dependent on your network).
Step 9. Complete your entry by clicking on OK.
Step 10. Restart Windows. F
IRSTVISION will automatically start. Communication between
F
IRSTVISION and your LAN should be established.
Step 11. Verify the connection by doing either of the following:
• Check the Gateway icon in the upper left corner of the display (no X over icon means
connected).
• Ping the gateway:
• Shut down F
IRSTVISION
• Select Start >Command Prompt to display a command prompt window.
• Type in "Ping <Gateway IP Address>". If the response to the Ping is returned from
the Gateway, then the connection is established.
Figure 3.13 Command Prompt
Step 12. Close any remaining windows.
Step 13. You should now "Establish Gateway Communication"
.
3.6 Establish Gateway Communication
NOTE: FIRSTVISION1.5 (and above) must be used with gateway versions 3.x and above.