Home Security System User Manual
Table Of Contents
- ONYX®FirstVision™
- Fire Alarm System Limitations
- Installation Precautions
- FCC Warning
- Section 1 Introduction
- Section 2 FirstVision Installation Instructions
- Section 3 Enabling FirstVision to Monitor Your Building
- 3.1 Process Overview
- 3.2 Make Connections to FirstVision
- 3.3 Turn on Power to FirstVision
- 3.4 Set the FirstVision Clock and Time Zone
- 3.5 Establish Communication Between Your LAN and FirstVision
- 3.6 Establish Gateway Communication
- 3.7 Copy Your Exported Building Design to FirstVision
- 3.8 Display Your Building Design on FirstVision
- 3.9 Test Your Building Design on FirstVision
- 3.10 Touch Screen Calibration
- Section 4 Operating Basics of FirstVision
- 4.1 Normal Operation (No Events Being Reported)
- Figure 4.1 FirstVision Display Example: No Alarms
- Figure 4.2 FirstVision Display Example: Floor Number Button
- Figure 4.3 FirstVision Display Example: Building Information
- Figure 4.4 FirstVision Display Example: Zoomed Floor Plan
- Figure 4.5 FirstVision Display Example: Moving Through a Zoomed Floor Plan
- Figure 4.6 FirstVision Display Example: HAZMAT Information
- 4.2 Investigating Gateway Disconnection
- 4.3 Operation When a Fire Alarm is Received
- 4.4 Operation After a Fire Alarm Has Been Cleared
- 4.5 Accessing the Log File
- 4.1 Normal Operation (No Events Being Reported)
- Section 5 The Development of FirstVision
- 5.1 The Current Situation for a Firefighter
- 5.2 The Technology of FirstVision
- 5.3 Expected Firefighter Interaction with the FirstVision
- 5.3.1 Example Emergency Situations
- Figure 5.1 Fire Scene Scenario Floor Plan Information
- Figure 5.2 Fire Scene Scenario Roof Plan Information
- Figure 5.3 Fire Scene Scenario HAZMAT Information
- Figure 5.4 Fire Scene Scenario Building Information
- Figure 5.5 Example Building Site Plan Information
- Figure 5.6 Example HAZMAT Information
- Figure 5.7 Example Contact Information
- 5.3.1 Example Emergency Situations
- Index
3FIRSTVISION™ Installation and Operation Manual - P/N: 53034:Rev: A2 10/29/07
Section 1 Introduction
The contents of this manual are important and must be kept in close proximity to the hardware. If
building ownership is changed, this manual and all other testing and maintenance information must
also be passed to the current owner of the facility. A copy of this manual was shipped with the
equipment and is also available from the manufacturer.
1.1 FIRSTVISION Specifications
!
WARNING: Improper Installation
Improper installation, maintenance, or lack of routine testing could result in system malfunction.
!
CAUTION: Servicing FIRSTVISION
This product can only be serviced by authorized personnel. Only authorized personnel can remove
this product’s CPU back-cover or replace parts in this product. Unauthorized servicing personnel
performing product services is strictly prohibited and can void your warranty
NOTE: ONYX®FIRSTVISION™ is for Ancillary Use Only.
Table 1.1 FIRSTVISION Cabinet Specifications
Part Number FIRSTVISION-ENC
General:
Rough Opening Dimensions 18" W x 17.75" H x 3.5” D
Material Aluminum
Finish Black epoxy powder coat finish, fine texture
Mounting Panel
Enclosure:
Door Dimensions 20" W x 18.5" H x 0.4" D
Material 0.060 Galvaneal
Door Finish Black epoxy powder coat finish, fine texture – Door only
Door Plex shield 0.125 scratch resistant acrylic
Conduit punch outs (2) ½" and (2) ¾" on the top and bottom of the enclosure (8) total
Mounting (6) mounting holes for screw mtg. #10/12
Lock CFE – NOTIFIER® Standard Lock
Magnetic Latch Power Off/Command Latch release