Operating Manual Mode d’emploi Manual de Uso VisionPRO IAQ ® Total Home Comfort System 69-1815EFS-04
BE CAREFUL! Never use sharp instruments, such as a pencil or pen, to press touchscreen keys. To prevent damage to the thermostat, always press keys with your fingertip. This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. Need Help? For assistance with this product please visit http://yourhome.honeywell.
VisionPRO IAQ ® Table of contents About your new thermostat Appendices Programming at a glance...................... 2 Quick reference to controls................... 3 Quick reference to status display......... 4 Advanced functions............................. 20 In case of difficulty............................... 27 Limited warranty................................... 29 Programming & Operation Clock setting.......................................... 5 Fan setting......................................
Operating Manual About your new thermostat Your new thermostat is pre-programmed and ready to go. Just set the time and day. Then check the settings below and change if needed: 1. Set clock.........................................................................................................See page 5 2. Select fan setting: Preset to Auto...............................................................See page 6 3. Select system setting: Preset to Heat.......................................................
VisionPRO IAQ ® Quick reference to controls Press day(s) to set program schedule (see page 9) Press to select fan operation (see page 6) MON FAN Press to select system type (see page 7) AUTO Press to override program schedule (see pages 10-11) WED THU 70 Inside FRI Set To SAT 70 Following Schedule SYSTEM HEAT Press to set program schedule (see page 9) TUE OK TO PICK MULTIPLE DAYS 6:01 SCHED SUN Press to adjust temperature settings (see pages 9-11) Press for more options AM HOLD CLOCK
Operating Manual Quick reference to status display Current inside temperature Current day of week Temperature setting WED FAN Fan setting AUTO 70 Inside Set To System setting Current time HEAT 70 Following Schedule SYSTEM Recovery 6:01 SCHED 55 AM HOLD Humidity CLOCK SCREEN MORE Other display messages: • • • • • Cool On: Cooling system is activated Heat On: Heating system is activated Aux Heat On: Auxiliary heating system is activated Wait: Compressor protection activated (see page
VisionPRO IAQ ® WED Clock setting Inside FAN AUTO 70 Set To Press CLOCK 6:01 SCHED FAN AUTO 70 To set the current time display, press CLOCK, then press s or t to adjust the time. Press and hold s or t to advance the time more quickly. AM WED HOLD 70 Inside CLOCK SCREEN Set To Press DONE to save & exit (or press CANCEL to exit without changing the time).
Operating Manual Fan setting WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:01 SCHED AM HOLD CLOCK SCREEN MORE Press FAN Note: If a fan schedule is programmed, “Auto” will run the fan schedule. Press FAN to select fan operation, then press DONE: • On: Fan is always on. • Auto: Fan runs only when the heating or cooling system is on. • Circ: Fan runs randomly, about 35% of the time, not counting any run time with the heating or cooling system.
VisionPRO IAQ ® System setting Press the SYSTEM button to select, then press DONE: WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:01 SCHED AM HOLD CLOCK SCREEN Press SYSTEM MORE • Heat: Thermostat controls only the heating system. • Cool: Thermostat controls only the cooling system. • Off: Heating and cooling systems are off. • Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature.
Operating Manual EnergyStar settings for maximum cost savings ® It’s easy to program your system for maximum energy savings. You can program four time periods each day, with different settings for each day. This thermostat is pre-set to use EnergyStar program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period.
FAN 70 Inside AUTO Set To 70 VisionPRO IAQ ® To adjust program schedules Following Schedule WED FAN 6:00 70 Inside SCHED HOLD 6:00 Press EDIT DONE EDIT FAN TUE 70 CLOCK Following SCREEN MORE Schedule LEAVE RETURN AM WAKE Select day(s) MON Set To AM AUTO Press SCHED SLEEP CANCEL Set heat/cool levels WED THU FRI SAT SUN OK TO PICK MULTIPLE DAYS 70 AUTO HEAT CANCEL PERIOD 6:00 DONE WAKE 78 AM LEAVE RETURN SLEEP 1. Press SCHED, then EDIT. 2.
Operating Manual Program schedule override (temporary) Adjust temperature Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. 73 The new temperature will be maintained only until the time you set. When the timer expires, the program schedule will resume and set the temperature to the level you’ve programmed for the current time period.
VisionPRO IAQ ® Program schedule override (permanent) Press HOLD Adjust temperature WED FAN AUTO 70 Inside Set To Whatever temperature you set will be maintained 24 hours a day until you manually change it or press CANCEL (or SCHED) to cancel “Hold” and resume the program schedule. 73 Heat On SYSTEM HEAT 8:00 Press HOLD to permanently adjust the temperature. This will turn off the program schedule.
Operating Manual Vacation hold This feature can suspend the program schedule for extended periods of time. 1WED Set temperature FAN AUTO 70 Inside Set To 55 Press s or t to set the temperature you want, then press s or t to set the time of day you want the schedule to resume when you return. Press HOLD twice, then press s or t to select the number of days.
VisionPRO IAQ ® Special features Auto Changeover: When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Adaptive Intelligent Recovery: This feature allows the thermostat to “learn” how long the furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you set. Compressor Protection: This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage.
Operating Manual Screen lock WED FAN AUTO SCREEN LOCKED 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:00 SCHED 43 PM HOLD CLOCK SCREEN MORE To prevent tampering, the screen can be partially or fully locked. When partially locked, the screen displays SCREEN LOCKED for several seconds if a locked key is pressed. When the screen is fully locked, no keys function. To lock or unlock the screen, see advanced function 0670 on page 26.
VisionPRO IAQ ® WED Screen cleaning FAN AUTO SCREEN LOCKED 70 Inside Set To Press SCREEN 6:00 SCHED 70 Following Schedule PM HOLD CLOCK SCREEN MORE Screen lock timer (30 seconds) 30 SCHED HOLD SCREEN After 30 seconds, press DONE to resume normal operation, or press SCREEN again if you require more time for cleaning. Note: Do not spray any liquid directly on the thermostat. Spray liquids onto a cloth, then use the damp cloth to clean the screen. Use water or household glass cleaner.
Operating Manual Optional remote sensors If an outdoor sensor is installed, the current outdoor temperature is displayed. WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 Outside 6:01 SCHED Inside temperature 43 AM HOLD CLOCK SCREEN MORE If an indoor remote sensor is installed, the display shows the indoor temperature at the location of the sensor.
VisionPRO IAQ ® Humidification control Set Frost Control & humidity level 32 Inside Press MORE until the humidifier screen is displayed, then press s or t to set the humidity and Frost Control level. 5 FROST DEHUMIDIFIER 55 DONE Press to save & exit CANCEL When using Frost Protection, if frost/condensation appears on windows, lower the frost setting. Wait at least 1 day before adjusting the frost level again.
Operating Manual Dehumidification control Press to select Auto or Off Press to set desired humidity If installed to control a dehumidifier, the thermostat can activate it as needed to reduce humidity. 73 Inside DEHUMIDIFIER AUTO Press MORE until the dehumidifier screen is displayed, then press s or t to set the desired humidity level and operation (Auto or Off).
VisionPRO IAQ ® Ventilation control You can ventilate your home at any time: Press to set ventilation timer Press MORE until the ventilation screen is displayed, then press s or t to set the ventilation timer. You can set the timer to ventilate from 20 to 180 minutes, in 20-minute increments. To turn off the ventilator, select 0. AUTO VENT Press DONE to save and exit, or press CANCEL to exit without saving changes.
Operating Manual TUE Advanced functions FAN 70 Inside AUTO 1 2 Press and hold Press SYSTEM. blank center key until the display changes. TUE FAN AUTO 70 Inside Set To 70 SYSTEM Following Schedule HEAT Outside 6:01 SCHED AM HOLD 43 70 SYSTEM HEAT 6:01 AM DONE CANCEL TUE FAN Change settings as required (see pages 21-26). MORE 70 Inside AUTO Function 3 SCREEN Set To 0120 Set To 70 Setting 20 DONE 4 Press s/t to select function Press DONE to exit & save changes.
VisionPRO IAQ ® Advanced functions Year setting (first two digits) Function 0120 Options: Press s/t to change the first two digits of the year: 20 = Year 20xx 21 = Year 21xx Year setting (second two digits) Function 0130 Options: Press s/t to change the last two digits of the year: 01 - 99 (i.e., 2001 - 2099) Month setting Function 0140 Options: Press s/t to change the current month: 01 - 12 (i.e.
Operating Manual Advanced functions Program schedule on/off Function 0160 Options: Press s/t to turn the program schedule on or off: 0 Program schedule is off. Thermostat is non-programmable. 4 Program schedule is on (7-day programmable). Restore Energy Star schedule ® Function 0165 Options: Press s/t to restore default Energy Star settings: 0 No change 1 Restore factory default Energy Star settings Backlight Function 0280 Options: Press s/t to select how the screen is lighted: 0 Light on for approx.
VisionPRO IAQ ® Advanced functions Temperature format (°F/°C) Function 0320 Options: Press s/t to set the temperature display format: 0 Fahrenheit 1 Celsius Daylight savings time on/off Function 0330 Options: The thermostat is pre-programmed to automatically adjust to daylight savings time.
Operating Manual Advanced functions Furnace filter change reminder Function 0500 Options: This feature displays an alert to remind you to change the furnace filter.
VisionPRO IAQ ® Advanced functions Humidifier pad change reminder Function 0510 Options: This feature displays an alert to remind you to change the humidifier pad.
Operating Manual Advanced functions Program schedule periods Function 0540 Options: Press s/t to set the number of program periods: 2 Two program periods (Wake, Sleep) 4 Four program periods (Wake, Leave, Return, Sleep) Clock format Function 0640 Options: Press s/t to set the clock display format: 12 12-hour clock (i.e., “3:30 pm”) 24 24-hour clock (i.e.
VisionPRO IAQ ® In case of difficulty If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • • • Check circuit breaker and reset if necessary. Make sure power switch at heating & cooling system is on. Make sure furnace door is closed securely. No response to key presses (or temperature will not change) • Check to make sure the thermostat is not locked (see page 26).
Operating Manual In case of difficulty Heating or cooling system does not respond • Press SYSTEM to set system to Heat. Make sure the temperature is set higher than the Inside temperature. • Press SYSTEM to set system to Cool. Make sure the temperature is set lower than the Inside temperature. Check circuit breaker and reset if necessary. Make sure power switch at heating & cooling system is on. Make sure furnace door is closed securely. If “Wait” is displayed, the compressor protection timer is on.
VisionPRO IAQ ® 5-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of five (5) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
Automation and Control Systems Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com ® U.S. Registered Trademark. © 2008 Honeywell International Inc. US Patent No. 6,208,263; 6,373,376; 6,448,901; 6,926,076; 7,044,397; D509151; H25192; H25193 and other patents pending 69-1815EFS—04 Rev. M.S.
Mode d’emploi VisionPRO IAQ ® Total Home Comfort System
ATTENTION ! N’appuyez jamais sur les touches d’un écran tactile avec un instrument pointu tel qu’un stylo ou un crayon. Pour empêcher tout dommage au thermostat, appuyez toujours sur les touches du bout du doigt. Ce thermostat contient une pile au lithium qui pourrait contenir du perchlorate. Matériau contenant du perchlorate — des consignes de manipulation spéciales pourraient s'appliquer, prière de consulter www.dtsc.ca.gov/hazardouswaste/perchlorate.
VisionPRO IAQ ® Table des matières À propos de votre nouveau thermostat La programmation en bref........................ 34 Aide-mémoire sur les commandes.......... 35 Aide-mémoire sur l’affichage................... 36 Annexes Fonctions évoluées................................... 52 En cas de difficultés................................. 59 Garantie limitée......................................... 61 Programmation et fonctionnement Réglage de l’horloge.................................
Mode d’emploi À propos de votre nouveau thermostat Votre nouveau thermostat est pré-programmé et prêt à fonctionner. Il suffit de régler l’heure et le jour. Vérifiez ensuite les réglages ci-dessous et modifiez-les si besoin est : 1. Réglage de l’horloge..................................................................................Voir page 37 2. Sélection de la configuration du ventilateur : Pré-réglé sur Auto......Voir page 38 3. Sélection du mode de fonctionnement : Pré-réglé sur Chauffage......
VisionPRO IAQ ® Aide-mémoire des commandes Appuyez sur day (s) pour paramétrer le programme (voir page 41) Appuyez sur day (s) pour paramétrer le programme (voir page 38) MON FAN AUTO Appuyez pour sélectionner le type de fonctionnement (voir page 39) Appuyez pour paramétrer le programme (voir page 41) Appuyez pour annuler le programme (voir pages 42-43) TUE WED THU FRI 70 Inside Set To 70 Following Schedule SYSTEM HEAT SAT OK TO PICK MULTIPLE DAYS 6:01 SCHED AM HOLD CLOCK SCREEN Appuyez
Mode d’emploi Aide-mémoire de l’affichage d’état Température intérieure actuelle Jour actuel de la semaine Réglage de la température WED FAN Réglage ventilation AUTO 70 Inside Set To Réglage système Heure actuelle HEAT 70 Following Schedule SYSTEM Recovery 6:01 SCHED 55 AM HOLD Humidity CLOCK SCREEN MORE Autres messages affichés : • • • • • Cool On : l’installation de climatisation est en marche Heat On : l’installation de chauffage est en marche Aux Heat On : Le système de chauffag
VisionPRO IAQ ® WED Réglage de l’horloge Inside FAN AUTO 70 Set To Appuyez sur CLOCK 6:01 SCHED FAN AUTO 70 Pour régler l’affichage de l’heure actuelle, appuyez sur CLOCK, puis sur s ou t pour modifier l’heure. Appuyez sur s ou t maintenant la pression pour avancer l’heure plus rapidement.
Mode d’emploi Réglage du fonctionnement de la ventilation WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:01 SCHED AM HOLD CLOCK SCREEN MORE Appuyez sur FAN REMARQUE : Si un horaire est programmé pour le ventilateur, le ventilateur fonctionnera selon cet horaire lorsqu’il est en mode « Auto ». Appuyer sur le bouton FAN pour sélectionner le mode de fonctionnement du ventilateur, puis appuyer sur DONE : • On : Le ventilateur est constamment en marche.
VisionPRO IAQ ® Sélection du mode de fonctionnement Appuyer sur la touche SYSTEM pour sélectionner, puis appuyer sur DONE : WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:01 SCHED AM HOLD CLOCK SCREEN MORE Appuyez sur SYSTEM • Heat : Le thermostat ne commande que l’installation de chauffage. • Cool : Le thermostat ne commande que l’installation de climatisation. • Off : Arrêt des installations de chauffage et de climatisation.
Mode d’emploi Réglages EnergyStar pour économiser au maximum ® Il est facile de programmer votre système afin de réaliser un maximum d’économies d’énergie. Vous pouvez programmer quatre plages horaires chaque jour, avec différents arrangements pour chaque jour. Ce thermostat est préréglé pour utiliser les paramètres du programme Energy Star . Nous conseillons ces réglages car ils peuvent réduire vos dépenses de chauffage/ climatisation de jusqu’à 33%.
FAN 70 Inside AUTO Set To 70 VisionPRO IAQ ® Pour modifier le programme Following Schedule WED FAN 6:00 70 Inside Set To AM Appuyez sur SCHED AUTO SCHED HOLD 6:00 70 CLOCK Following Schedule SCREEN MORE LEAVE RETURN AM Appuyez sur EDIT DONE EDIT WAKE SLEEP CANCEL Sélectionnez Sélectionnez les niveaux de jour(s) chauffage/de climatisation MON FAN TUE WED THU FRI SAT SUN OK TO PICK MULTIPLE DAYS 70 AUTO HEAT CANCEL PERIOD 6:00 DONE WAKE 78 AM LEAVE RETURN Fixez l
Mode d’emploi Annulation de la programmation (momentanée) Réglez la température WED FAN AUTO 70 Inside Set To 73 HEAT Heat On SYSTEM HEAT Hold Temperature Until 8:00 SCHED 78 AM HOLD CLOCK SCREEN COOL MORE CANCEL Appuyez sur s ou t modifier immédiatement la température. Cela annule momentanément le réglage de température pour la plage actuelle. La nouvelle température sera maintenue jusqu’à l’heure fixée.
VisionPRO IAQ ® Annulation du programme (permanente) Appuyez HOLD Modifiez la température WED FAN AUTO 70 Inside Set To Quelle que soit la température fixée, elle sera conservée 24 heures sur 24 jusqu’à ce que vous la modifiez à la main, ou appuyez sur CANCEL (ou SCHED) pour annuler « Hold » et reprendre le programme. 73 Heat On SYSTEM HEAT 8:00 Appuyez sur HOLD pour modifier la température de manière permanente. Cela arrêtera le programme.
Mode d’emploi Suspension vacances 1 Programmez la température WED FAN AUTO 70 Inside Set To 55 SYSTEM HEAT Hold Temperature Until 6:00 SCHED PM HOLD CLOCK SCREEN MORE CANCEL WED 2 Appuyez pour régler l’heure à FAN laquelle annulé Inside le programme Set sera To AUTO 70 3 Appuyez 2 fois sur HOLD 55 SYSTEM HEAT Hold Temperature Until 14 SCHED HOLD DAYS CLOCK SCREEN MORE CANCEL Cette fonction peut suspendre le programme pour une période prolongée.
VisionPRO IAQ ® Fonctions spéciales Commutation automatique : Lorsqu’il est réglé sur Auto, le thermostat sélectionne automatiquement chauffage ou climatisation en fonction de la température intérieure. Adaptive Intelligent Recovery : Cette fonction permet au thermostat « d’apprendre » combien de temps il faut à la chaudière et au climatiseur pour atteindre la température demandée de manière à ce que cette température soit atteinte à l’heure fixée.
Mode d’emploi Verrouillage de l’écran WED FAN AUTO SCREEN LOCKED 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:00 SCHED 43 PM HOLD CLOCK SCREEN Voir Fonction évoluée 0670 (page 58) où figurent les choix screen lock 69-1815EFS—04 MORE Pour empêcher toute modification intempestive, il est possible de verrouiller totalement ou partiellement l’écran.
VisionPRO IAQ ® WED Nettoyage de l’écran FAN AUTO SCREEN LOCKED 70 Inside Set To Appuyez sur SCREEN 6:00 SCHED 70 Following Schedule PM HOLD CLOCK SCREEN MORE Minuteur de verrouillage d’écran (30 secondes) 30 SCHED HOLD SCREEN Au bout de 30 secondes, appuyez sur DONE pour reprendre le fonctionnement normal ou appuyez sur SCREEN s’il faut davantage de temps pour nettoyer. Remarque : Ne jamais pulvériser aucun liquide directement sur le thermostat.
Mode d’emploi Capteurs à distance en option Si un capteur extérieur est installé, la température extérieure s’affiche. WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 Outside 6:01 SCHED 43 AM HOLD Température Intérieure 69-1815EFS—04 CLOCK SCREEN MORE Température Extérieure Si un capteur intérieur est installé, l’affichage indique la température intérieure à l’emplacement où se trouve le capteur.
VisionPRO IAQ ® Contrôle de humidification Placez la commande de gel et le niveau d’humidité 32 Inside Appuyez sur MORE ce que l’écran humidité s’affiche et appuyez ensuite sur s ou t pour programmer le niveau de commande d’humidité et de gel. 5 FROST DEHUMIDIFIER 55 DONE CANCEL Appuyez pour sauvegarder et quitter Remarque : Si vous n’avez pas une sonde de température extérieure, le niveau de commande de gel ne sera pas montré.
Mode d’emploi Contrôle de déshumidification Choisissez Auto ou Off Placez l’humidité de niveau 73 Inside DEHUMIDIFIER AUTO DONE 55 CANCEL Appuyez pour sauvegarder et quitter Remarque : La commande Auto/Off n’existe qu’en présence d’un déshumidificateur pour toute la maison (ce qui n’est pas le cas lorsque la déshumidification est faite au moyen du système de refroidissement).
VisionPRO IAQ ® Contrôle de ventilation Vous pouvez aérer votre maison à tout moment : Appuyez pour placer le temporisateur de ventilation Appuyez sur MORE jusqu’à ce que l’écran de ventilation soit montré, puis appuyez s ou t pour placer le temporisateur de ventilation. Vous pouvez placer le temporisateur pour aérer de 20 à 180 minutes, dans des incréments de 20-minute. Pour arrêter le ventilateur, choisissez 0.
Mode d’emploi TUE Fonctions évoluées 70 FAN Inside AUTO 1 2 Appuyez sur la tou- Appuyez sur SYSTEM. che centrale vide et continuez à le faire jusqu’à ce que l’affichage change. TUE FAN AUTO 70 Inside Set To 70 SYSTEM Following Schedule HEAT Outside 6:01 SCHED AM HOLD 70 SYSTEM HEAT 6:01 AM DONE CANCEL TUE FAN 43 Modifiez les paramètres selon les besoins (voir MORE pages 53 à 57).
VisionPRO IAQ ® Fonctions évoluées Programmation de l’année (deux premiers chiffres) Fonction 0120 Choix : Appuyez s/t pour modifier les deux premiers chiffres de l’année. 20 = Année 20xx 21 = Année 21xx Programmation de l’année (deux derniers chiffres) Fonction 0130 Choix : Appuyez s/t pour modifier les deux derniers chiffres de l’année. 01 - 99 (c-à-d. 2001 - 2099) Programmation du mois Fonction 0140 Choix : Appuyez s/t pour modifier le mois actuellement affiché. 01 - 12 (c-à-d.
Mode d’emploi Fonctions évoluées Programmation marche/arrêt Fonction 0160 Choix : Appuyez s/t pour mettre la programmation en marche ou à l’arrêt. 0 La programmation est à l’arrêt. Le thermostat n’est pas programmable. 4 La programmation est en marche (7 jours programmable).
VisionPRO IAQ ® Fonctions évoluées Format de température (°F/°C) Fonction 0320 Choix : Appuyez s/t pour programmer le format de l’affichage : 0 Fahrenheit 1 Celsius Changement horaire été/hiver Fonction 0330 Choix : Le thermostat est preprogramme pour effectuer automatiquement le changement heure d’été. Appuyez sur s/t pour selectionner : 0 Arrêt : pas de réglage pour changement heure d’été.
Mode d’emploi Fonctions évoluées Rappel de changement du filtre de la chaudière Fonction 0500 Choix : Cette fonction affiche une alerte pour vous rappeler de changer le filtrede la chaudière.
VisionPRO IAQ ® Fonctions évoluées Rappel de changement du tampon de l’humidificateur Fonction 0510 Choix : Cette fonction affiche une alerte pour vous rappeler de changer le tampon de l’humidificateur. Appuyez s/t pour programmer la fréquence souhaitée.
Mode d’emploi Fonctions évoluées Plages du programme Fonction 0540 Choix : Appuyez s/t pour programmer le nombre de plages de programme. 2 Deux plages de programme (Wake, Sleep) 4 Quatre plages de programme (Wake, Leave, Return, Sleep) Format de l’horloge Fonction 0640 Choix : Appuyez s/t pour programmer le format d’affichage de l’horloge. 12 Horloge 12 heures (c.-à-d. 3:30 p.m.) 24 Horloge 24 heures (c.-à-d. 15:30 p.m.
VisionPRO IAQ ® En cas de difficultés Si vous rencontrez des difficultés avec votre thermostat, veuillez essayer les suggestions ci-dessous. La plupart des problèmes se corrigent rapidement et facilement. • Vérifiez le disjoncteur et réenclenchez-le. Vérifiez que le commutateur d’alimentation de l’installation de chauffage ou de la climatisation est sur marche. Vérifiez que la porte de la chaudière est bien fermée.
Mode d’emploi En cas de difficultés Le chauffage ou la climatisation ne réagit pas. • Appuyez sur la touche SYSTEM pour mettre le système sur Chauffage. Vérifiez que le réglage de température est supérieur à la température intérieure. • Appuyez sur la touche SYSTEM pour mettre le système sur Climatisation. Vérifiez que le réglage de température est inférieur à la température intérieure. Vérifiez le disjoncteur et le réenclencher si nécessaire.
VisionPRO IAQ ® Garantie limitée de 5 ans Honeywell garantit ce produit, à l’exception des piles, contre tout vis de fabrication ou de matière dans des conditions d’utilisationet de service normales, pendant une durée de cinq (5) ans à compter de la date d’achat par le consommateur. Si à un moment quelconque pendant la durée de la garantie, le produit est jugé défectueux ou tombe en panne, Honeywell le réparera ou le remplacera (au choix d’Honeywell).
Systèmes d’automatisation et de contrôle Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com ® Marque déposée aux É.-U. © 2008 Honeywell International Inc. Brevet américain n s 6 208 263; 6 373 376; 6 448 901; 6 926 076; 7 044 397; D509151; H25192; H25193 et autres brevets en instance 69-1815EFS—04 Rev. M.S.
Manual de Uso VisionPRO IAQ ® Total Home Comfort System
¡TENGA CUIDADO! Nunca utilice instrumentos con punta afilada, como un lápiz o bolígrafo para oprimir las teclas de la pantalla activada por tacto. Para evitar dañar el termostato, siempre oprima las teclas con la punta del dedo. Este termostato tiene una batería de litio que puede contener perclorato. Perclorato: puede ser necesario manipularlo con métodos especiales. Visite www.dtsc.ca.gov/hazardouswaste/perchlorate. ¿Necesita ayuda? Para recibir asistencia con este producto visite http://yourhome.
VisionPRO IAQ ® Índice de contenidos Acerca de su nuevo termostato Apéndices Programación a simple vista.................... 66 Referencia rápida de los controles.......... 67 Referencia rápida de la pantalla.............. 68 Funciones avanzadas............................... 84 En caso de dificultades............................ 91 Garantía limitada....................................... 93 Programación y operación Ajuste del reloj.......................................... 69 Ajuste del ventilador...
Manual de Uso Acerca de su nuevo termostato El nuevo termostato viene preprogramado y listo para usar. Todo lo que tiene que hacer es ajustar la hora y el día. Luego verifique los siguientes ajustes y cámbielos si es necesario: 1. Ajuste la hora..............................................................................................See page 69 2. Seleccione el ajuste del ventilador: Predeterminado en Auto.............See page 70 3. Seleccione el ajuste del sistema: Predeterminado en Heat..............
VisionPRO IAQ ® Referencia rápida de los controles Oprima el día o los días para ajustar el horario de programa (ver página 73) Oprima para seleccionar el funcionamiento del ventilador (ver página 70) Oprima para seleccionar el tipo de sistema (ver página 71) Oprima para ajustar el horario de programa (ver página 73) Oprima para anular el horario de programa (ver páginas 74-75) MON FAN AUTO TUE WED THU 70 Inside Set To SAT 70 Following Schedule SYSTEM HEAT FRI OK TO PICK MULTIPLE DAYS 6:01 S
Manual de Uso Referencia rápida de la pantalla Temperatura interior actual Día de la semana actual WED FAN Ajustes del ventilador Ajustes del sistema AUTO 70 Inside Set To HEAT 70 Following Schedule SYSTEM Recovery 6:01 SCHED 55 AM HOLD Humidity CLOCK SCREEN MORE Hora actual Otros mensajes de pantalla: • • • • • Cool On: El sistema de refrigeración está activado Heat On: El sistema de calefacción está activado Aux Heat On: El sistema de calefacción auxiliar está activado Wait: Protecc
VisionPRO IAQ ® WED Ajuste del reloj Inside FAN AUTO 70 Set To Oprima CLOCK 6:01 SCHED FAN AUTO 70 Para ajustar la hora actual en pantalla, oprima CLOCK, luego oprima s o t para ajustar la hora. Mantenga oprimido s o t para avanzar la hora con más rapidez. AM WED HOLD 70 Inside CLOCK SCREEN Set To Oprima DONE para guardar y salir (u oprima CANCEL para salir sin cambiar la hora).
Manual de Uso Ajuste del ventilador WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:01 SCHED AM HOLD CLOCK SCREEN MORE Oprima FAN Nota: Si se programa un cronograma del ventilador, el modo ‘Auto’ (automático) lo ejecutará. Presione FAN (ventilador) para seleccionar la función de ventilador; luego, presione DONE (listo): • On: El ventilador está siempre encendido. • Auto: El ventilador funciona sólo cuando el sistema de calefacción o de refrigeración está encendido.
VisionPRO IAQ ® Ajustes del sistema WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:01 SCHED • Heat: El termostato controla sólo el sistema de calefacción. • Cool: El termostato controla sólo el sistema de refrigeración. AM HOLD Presione el botón SYSTEM (sistema) para realizar la selección; luego, presione DONE (listo): CLOCK SCREEN Oprima SYSTEM MORE • Off: Los sistemas de calefacción y refrigeración están apagados.
Manual de Uso Ajustes EnergyStar para un ahorro máximo de costos ® Es sencillo programar su sistema para lograr un máximo ahorro de energía. Usted puede programar cuatro períodos por día, con distintos ajustes para cada día. El termostato viene preajustado para usar los ajustes de programa EnergyStar . Recomendamos estos ajustes, dado que pueden reducir sus gastos de calefacción/ refrigeración hasta un 33%. (Ver la página siguiente para ajustar las horas y temperaturas para cada período).
FAN 70 Inside AUTO Set To 70 VisionPRO IAQ ® Para ajustar los horarios de programas Following Schedule WED FAN 6:00 70 Inside SCHED HOLD 6:00 Oprima EDIT DONE EDIT FAN TUE 70 CLOCK Following SCREEN MORE Schedule LEAVE RETURN AM WAKE Seleccione día(s) MON Set To AM AUTO Oprima SCHED WED SLEEP CANCEL Seleccione niveles de heat/cool THU FRI SAT SUN OK TO PICK MULTIPLE DAYS 70 AUTO HEAT CANCEL PERIOD 6:00 DONE WAKE 78 AM LEAVE RETURN SLEEP COOL CANCEL 1.
Manual de Uso Anulación (temporaria) de horario de programas Ajuste la temperatura WED FAN AUTO 70 Inside Set To 73 HEAT Heat On SYSTEM HEAT Hold Temperature Until 8:00 SCHED HOLD 78 AM CLOCK SCREEN COOL MORE CANCEL Oprima s o t para ajustar inmediatamente la temperatura. Esto anulará temporariamente el ajuste de temperatura para el período actual. La nueva temperatura se mantendrá hasta la hora que haya fijado.
VisionPRO IAQ ® Anulación (permanente) de horario de programas Oprima HOLD Ajuste la temperatura WED FAN AUTO 70 Inside Set To Cualquier temperatura que fije se mantendrá 24 horas al día, hasta que la cambie manualmente, u oprima CANCEL (o SCHED) para cancelar “Hold” y reanude el horario de programas. 73 Heat On SYSTEM HEAT 8:00 Oprima HOLD para ajustar permanentemente la temperatura. Esto apagará el horario de programas.
Manual de Uso Suspensión por vacaciones Esta función puede suspender el horario de programas por largos períodos. 1WED Fije la temperatura FAN AUTO 70 Inside Set To 55 Oprima s o t para fijar la temperatura que desea, luego oprima s o t para fijar la hora del día en que desea que se reanude el horario cuando usted regrese. Oprima HOLD dos veces, luego oprima s o t para seleccionar el número de días.
VisionPRO IAQ ® Funciones especiales Cambio automático: Cuando el sistema se fija en Auto, el termostato selecciona automáticamente calefacción o refrigeración de acuerdo a la temperatura del interior. Adaptive Intelligent Recovery: Permite que el termostato “aprenda” cuánto tiempo les lleva a la estufa y al acondicionador de aire alcanzar la temperatura programada, de modo que se alcance la temperatura a la hora fijada.
Manual de Uso Bloqueo de pantalla WED FAN AUTO SCREEN LOCKED 70 Inside Set To Following Schedule SYSTEM HEAT 70 6:00 SCHED 43 PM HOLD CLOCK SCREEN Vea la función avanzada 0670 (página 90) para las opciones de bloqueo de pantalla MORE Para prevenir alteraciones no deseadas, la pantalla se puede bloquear parcial o totalmente. Cuando está parcialmente bloqueada, la pantalla muestra el mensaje SCREEN LOCKED durante varios segundos si se oprime una tecla bloqueada.
VisionPRO IAQ ® WED Limpieza de pantalla FAN AUTO SCREEN LOCKED 70 Inside Set To Oprima SCREEN 6:00 SCHED 70 Following Schedule PM HOLD CLOCK SCREEN MORE Temporizador de bloqueo de pantalla (30 segundos) 30 SCHED HOLD SCREEN Después de 30 segundos, oprima DONE para reanudar el funcionamiento normal, u oprima SCREEN nuevamente si necesita más tiempo para limpiar. Nota: No rocíe ningún líquido directamente sobre el termostato.
Manual de Uso Sensores remotos opcionales Si hay un sensor exterior instalado, se muestra la temperatura exterior actual. WED FAN AUTO 70 Inside Set To Following Schedule SYSTEM HEAT 70 Outside 6:01 SCHED 43 AM HOLD Temperatura interior 69-1815EFS—04 CLOCK SCREEN MORE Si hay un sensor remoto interior instalado, la pantalla muestra la temperatura interior en la ubicación del sensor.
VisionPRO IAQ ® Control de humidificación Fije el control de la helada y el nivel de la humedad 32 Oprima MORE hasta que se exhibe la pantalla del humectador, después oprima s o t fijar el nivel del control de la humedad y de la helada. 5 Inside FROST DEHUMIDIFIER 55 DONE Oprima para guardar y salir CANCEL Si aparece escarcha o condensación en las ventanas cuando utiliza la protección contra heladas, baje la configuración de heladas.
Manual de Uso Control de deshumidificación Oprima para seleccionar Auto o Off Seleccione la humedad deseada Si está instalado para controlar un deshumidificador, el termóstato puede activarlo como necesario para reducir humedad. 73 Inside DEHUMIDIFIER AUTO Oprima MORE hasta que aparezca la pantalla del deshumidificador, luego oprima s o t para fijar el nivel y la operación deseados de la humedad (Auto o Off).
VisionPRO IAQ ® Control de la ventilación Usted puede ventilar su hogar en cualquier momento: Fije el tiempo de la ventilación AUTO VENT Oprima MORE hasta que se exhibe la pantalla de ventilación, después presione s o t para fijar el tiempo de la ventilación. Usted puede elegir 20 a 180 minutos, en incrementos de los 20-minute. Para dar vuelta apagado al ventilador, seleccione 0.
Manual de Uso TUE Funciones avanzadas FAN 70 Inside AUTO 1 2 Mantenga oprimida Oprima SYSTEM. la tecla vacía del centro hasta que cambie la pantalla. TUE FAN AUTO 70 Inside Set To 70 SYSTEM Following Schedule HEAT Outside 6:01 SCHED AM HOLD 43 3 SCREEN Set To 70 SYSTEM HEAT 6:01 AM DONE CANCEL TUE FAN Cambie los ajustes según sea necesario (ver páginas 85-89).
VisionPRO IAQ ® Funciones avanzadas Ajuste de año (primeros dos dígitos) Función 0120 Opciones: Oprima s/t para cambiar los primeros dos dígitos del año: 20 = Año 20xx 21 = Año 21xx Ajuste de año (segundos dos dígitos) Función 0130 Opciones: Oprima s/t para cambiar los últimos dos dígitos del año: 01 - 99 (ej., 2001 - 2099) Ajuste de mes Función 0140 Opciones: Oprima s/t para cambiar el mes actual: 01 - 12 (ej.
Manual de Uso Funciones avanzadas Horario de programas on/off Función 0160 Opciones: Oprima s/t para encender o apagar el horario de programas: 0 Horario de programas apagado. El termostato no es programable.
VisionPRO IAQ ® Funciones avanzadas Formato de temperatura (°F/°C) Función 0320 Opciones: Oprima s/t para ajustar el formato devisualización de temperatura: 0 Fahrenheit 1 Celsius Horario de ahorro de energía on/off Función 0330 Opciones: El termostato está preprogramado para ajustarse automáticamente al horario de ahorro de energía diurno. Oprima s/t para seleccionar: 0 Off: Sin ajuste para horario de ahorro de energía diurno.
Manual de Uso Funciones avanzadas Recordatorio de cambio de filtro de la estufa Función 0500 Opciones: Esta función muestra un alerta para recordarle que cambie el filtro de la estufa.
VisionPRO IAQ ® Funciones avanzadas Recordatorio de cambio de paño del humidificador Función 0510 Opciones: Esta función muestra un alerta para recordarle que cambie el paño del humidificador. Oprima s/t para fijar el intervalo deseado: 0 Apagada Nota: Oprima RESET para 1 30 días de funcionamiento, 90 días calendario ** cancelar la alerta.
Manual de Uso Funciones avanzadas Períodos de horario de programas Función 0540 Opciones: Oprima s/t para fijar la cantidad de períodos de programas: 2 Dos períodos de programa (Wake, Sleep) 4 Cuatro períodos de programa (Wake, Leave, Return, Sleep) Formato de reloj Función 0640 Opciones: Oprima s/t para fijar la cantidad de períodos de programas: 12 Horario de 12 horas (ej.: “3:30 PM”) 24 Horario de 24 horas (ej.
VisionPRO IAQ ® En caso de dificultades Si usted tiene dificultades con su termostato, pruebe las sugerencias que figuran a continuación. La mayoría de los problemas se pueden solucionar rápida y fácilmente. • Verifique el disyuntor y reinicie si es necesario. Asegúrese de que esté encendido el interruptor del sistema de calefacción y refrigeración. Asegúrese de que esté bien cerrada la puerta de la estufa.
Manual de Uso En caso de dificultades No responde el sistema de calefacción o de refrigeración • Oprima SYSTEM para fijar en sistema en Calefacción. Asegúrese de que la temperatura de ajuste sea mayor que la temperatura interior. • Oprima SYSTEM para fijar en sistema en Refrigeración. Asegúrese de que la temperatura de ajuste sea menor que la temperatura interior. Verifique el disyuntor y reinicie si es necesario.
VisionPRO IAQ ® Garantía limitada de 5 años Honeywell garantiza que, a excepción de la batería y en condiciones de uso y servicio normales, este producto no tendrá defectos de fabricación ni de materiales durante cinco (5) años a partir de la fecha de compra por parte del consumidor. Si durante ese período de garantía, el producto resulta defectuoso o tiene problemas de funcionamiento, Honeywell lo reparará o reemplazará (a criterio de Honeywell).
Automation and Control Systems Systèmes d’automatisation et de contrôle Sistemas para automatización y control Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 http://yourhome.honeywell.com Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. Imprimé aux É.-U. sur du papier recyclé contenant au moins 10 % de fibres de papier recyclées après consommation.