Datasheet

8
sensing.honeywell.com
Pressure Range Specifications
PCB Pad Layouts
Table 7. Pressure Range Specifications (continued)
Pressure
Range
(see Figure 3)
Pressure
Range
Unit Overpressure
1
Burst Pressure
2
Common Mode
Pressure
3
Total Error Band
4
(%FSS)
Long-term Stability
1000 hr, 25 °C
(%FSS)
Pmin. Pmax.
1 psi to 150 psi
Differential
001PD -1 1 psi 10 15 150 ±1.5% ±0.25%
005PD -5 5 psi 30 40 150 ±1.5% ±0.25%
015PD -15 15 psi 60 120 150 ±1.5% ±0.25%
030PD -30 30 psi 120 240 150 ±1.5% ±0.25%
060PD -60 60 psi 250 250 250 ±1.5% ±0.25%
Gage
001PG 0 1 psi 10 15 150 ±1.5% ±0.25%
005PG 0 5 psi 30 40 150 ±1.5% ±0.25%
015PG 0 15 psi 30 60 150 ±1.5% ±0.25%
030PG 0 30 psi 60 120 150 ±1.5% ±0.25%
060PG 0 60 psi 120 240 250 ±1.5% ±0.25%
100PG 0 100 psi 250 250 250 ±1.5% ±0.25%
150PG 0 150 psi 250 250 250 ±1.5% ±0.25%
1
Overpressure:Themaximumpressurewhichmaysafelybeappliedtotheproductforittoremaininspecificationoncepressureisreturnedtotheoperatingpressurerange.Exposure
tohigherpressuresmaycausepermanentdamagetotheproduct.Unlessotherwisespecifiedthisappliestoallavailablepressureportsatanytemperaturewiththeoperating
temperature range.
2
Burstpressure:Themaximumpressurethatmaybeappliedtoanyportoftheproductwithoutcausingescapeofpressuremedia.Productshould not be expected to function after
exposure to any pressure beyond the burst pressure.
3
Commonmodepressure:Themaximumpressurethatcanbeappliedsimultaneouslytobothportsofadifferentialpressuresensorwithoutcausingchangesinspecified
performance.
4
TotalErrorBand:Themaximumdeviationfromtheidealtransferfunctionovertheentirecompensatedtemperatureandpressurerange.Includesallerrorsduetooffset,fullscale
span, pressure non-linearity, pressure hysteresis, repeatability, thermal effect on offset, thermal effect on span, and thermal hysteresis.
Table 8. Pinouts
Output Type Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6
Digital(I
2
C, SPI) GND V
DD
SS/INT NC SDA SCL
Analog GND NC V
out
NC NC V
DD
Figure 4. Recommended PCB Layouts
DIP SMT Leadless SMT
5,00
[0.1
97]
6,00
[0.236]
2,54
[0.1]
2,73
[0.107]
8,00
[0.315]
11,00
[0.433]
8,85
[0.348]
12,35
[0.31
5]
1
2
3
65
4
0,65
[0.026]
Gage reference hole: do not plug
11,0
[0.433]
12
3
6
54
5,00
[0.197]
6,00
[0.236]
6X ø0.73
[0.029]
2,54
[0.1]
2,73
[0.1
07]
8,00
[0.315]
11,25
[0.443]
Gage reference hole: do not plug
7,00
[0.28]
3,00
[0.118]
2,50
[0.098]
2,73
[0.107]
8,00
[0.315]
4,00
[0.1
57]
3,25
0.128]
8,00
[0.315]
1,30
[0.051]
123
654
Gage reference hole: do not plug