Datasheet

ManualsBrandsHoneywell ManualsIntegrated Circuits (ICs)Basic Board Mount Pressure Sensor 0 ... 60 psi, Gauge, Digital/I²C, Gas/Liquid, SMT

Sensing and Internet of Things

ABP SERIES

Basic Board Mount Pressure Sensors

High Accuracy, Compensated/Ampliﬁed

60 mbar to 10 bar | 6 kPa to 1 MPa | 1 psi to 150 psi

Digital or Analog Output, Liquid Media Capable

DESCRIPTION

The ABP Series are piezoresistive silicon

pressure sensors offering a ratiometric

analog or digital output for reading

pressure over the specified full scale

pressure span and temperature range.

They are calibrated and temperature

compensated for sensor offset,

sensitivity, temperature effects and

accuracy errors (which include non-

linearity, repeatability and hysteresis)

using an on-board Application Specific

Integrated Circuit (ASIC). Calibrated

output values for pressure are updated

at approximately 1 kHz for analog and

2 kHz for digital. All products are

designed and manufactured according

to ISO 9001 standards.

• Dry gases option: The input port is

limited to non-corrosive, non-ionic

media (e.g., dry air, gases) and should

not be exposed to condensation. The

gases are limited to media compatible

with high temperature polyamide,

silicone, alumina ceramic, silicon, gold,

and glass.

• Liquid media option: Includes an

additional silicone-based gel coating

to protect the electronics under

port P1, which enables use with

non-corrosive liquids (e.g. water and

saline) and in applications where

condensation can occur. Since port P2

is designed for use with non-corrosive

liquids, this option is often suitable for

wet-wet differential sensing.

DIFFERENTIATION

• Enhanced accuracy helps the design

engineer fully understand the error in

measurement.

• Wide supply voltage range offers

design flexibility.

• Power consumption when utilizing

sleep mode option allows for use in

battery-powered applications.

VALUE TO CUSTOMERS

• Simplifies design-in: Small size

saves room on the PC board (PCB),

or simplifies design in smaller and

lower power devices. Meets Moisture

Sensitivity Level 1 requirements, which

allows for unlimited shelf life when

stored at <30 ºC/85 %RH and, under

most storage conditions, allows for

PCB soldering without any material

concern about solder joint quality due

FEATURES

• Measures gage and differential

pressures

• Total Error Band (see Figure 1): ±1.5 %FSS

• Liquid media option: Allows for wet/

wet operation on dual ported devices

• Industry-leading long-term stability:

±0.25 %FSS

• Industry-leading accuracy: ±0.25 %FSS

BFSL

• Wide pressure range: 60 mbar to 10 bar

| 6 kPa to 1 MPa | 1 psi to 150 psi

• As small as 8 mm x 7 mm

• High burst pressures (see Table 7)

• Calibrated over temperature range of 0°C

to 50°C [32°F to 122°F]

• Operates from a single power supply of

either 3.3 Vdc or 5.0 Vdc

• Output: Ratiometric analog or I

C- or

SPI-compatible 12-bit digital

• Power consumption: 2 uA typical when

utilizing sleep mode option

• Meet IPC/JEDEC J-STD-020D.1

Moisture Sensitivity Level 1

requirements

• REACH and RoHS compliant

• Options: Internal diagnostic function,

liquid media, sleep mode, temperature

output

32305128

Issue F

to aging of the sensor terminals, which

minimizes the concern about aging

of the terminals prior PCB assembly.

Pressure choices allow engineers

to select range required for their

application. Leadless SMT, SMT, and

DIP package options.

• Cost-effective: Small size helps

engineers reduce design and

manufacturing costs while maintaining

enhanced performance and reliability

of the systems they design.

• Accurate: Total Error Band (TEB) and

wide pressure range enable engineers

to optimize system performance by

improving resolution and system

accuracy. Optional internal diagnostics

validate that the sensor readings are

correct.

• Flexible: Supply voltage range, variety

of pressure units, types, and ranges,

output options, and wide operating

temperature range simplify use in the

application.

• Versatile: Wet-media compatibility,

sleep mode, and temperature

output options make the sensor a

versatile choice for Internet of Things

applications.

• Honeywell Brand: Utilize proprietary

Honeywell technology, and are

protected by multiple global patents.

POTENTIAL APPLICATIONS

• Medical: CPAP, blood analysis, blood

pressure monitoring, breast pumps,

drug dosing, hospital beds, massage

machines, oxygen concentrators,

patient monitoring, sleep apnea

equipment, urine analyzers,

ventilators/portable ventilators, and

wound therapy

• Industrial: Air brakes, HVAC/

transmitters, life sciences, material

handling, pneumatic control and

regulation, process gas monitoring,

and valve positioning/positioners

• Commercial: Air beds, coffee makers,

and washing machines

PORTFOLIO

Honeywell offers a variety of

board mount pressure sensors for

potential use in medical and industrial

applications. To view the entire product

portfolio, click here.

Summary of content (14 pages)

PAGE 1
ABP SERIES 32305128 Issue F Basic Board Mount Pressure Sensors High Accuracy, Compensated/Amplified 60 mbar to 10 bar | 6 kPa to 1 MPa | 1 psi to 150 psi Digital or Analog Output, Liquid Media Capable DESCRIPTION The ABP Series are piezoresistive silicon pressure sensors offering a ratiometric analog or digital output for reading pressure over the specified full scale pressure span and temperature range.
PAGE 2
Basic Board Mount Pressure Sensors, ABP Series FIGURE 1. TOTAL ERROR BAND Total Error Band (TEB) is a single specification that includes all possible sources of error. TEB should not be confused with accuracy, which is actually a component of TEB. TEB is the worst error that the sensor could experience. The TEB specification on a datasheet may be confusing. Honeywell uses the TEB specification in its datasheet because it is the most comprehensive measurement of a sensor’s true accuracy.
PAGE 3
Basic Board Mount Pressure Sensors, ABP Series TABLE 5. OPERATING SPECIFICATIONS ANALOG CHARACTERISTIC Supply voltage (Vsupply):1, 2, 3 3.3 Vdc 5.0 Vdc Supply current: 3.3 Vdc 5.0 Vdc sleep mode option Operating temperature range 4 Compensated temperature range5 Temperature output option DIGITAL UNIT MIN. TYP. MAX. MIN. TYP. MAX. 3.0 4.75 3.3 5.0 3.6 5.25 3.0 4.75 3.3 5.0 3.6 5.25 Vdc — — — 2.1 2.7 — 2.8 3.8 — — — — 3.1 3.7 1 3.9 4.
PAGE 4
Basic Board Mount Pressure Sensors, ABP Series FIGURE 2. TRANSFER FUNCTION LIMITS1 Output (%Vsupply) Analog Versions Compensated Pressure Range 100 90 80 70 60 Ideal 50 40 30 20 10 0 1.5% Total Error Band 0 Pmin. Output (V) = 1 2 3 4 5 6 7 8 9 Pressure (example unit) 0.8 x Vsupply Pmax. – Pmin. 10 Pmax. x (Pressureapplied – Pmin.) + 0.10 x Vsupply Output (% of 214 counts) Digital Versions Compensated Pressure Range 100 90 80 70 60 50 40 30 20 10 0 Ideal 1.
PAGE 5
Basic Board Mount Pressure Sensors ABP Series—High Accuracy Basic Board Mount Pressure Sensors, ABP Series Digital or Analog Output, Compensated/Amplified FIGURE 3. NOMENCLATURE AND ORDER GUIDE For example, ABPDNNN150PGAA3 defines an ABP Series Amplified Basic Pressure Sensor, DIP package, NN pressure port, dry gases only, no diagnostics,150 psi gage pressure range, analog output type, 10% to 90% of Vsupply (analog), transfer function, no temperature output, no sleep mode, 3.3 Vdc supply voltage.
PAGE 6
Basic Board Mount Pressure Sensors, ABP Series TABLE 7. PRESSURE RANGE SPECIFICATIONS PRESSURE PRESSURE RANGE RANGE PMAX. (SEE FIGURE 3.) PMIN.
PAGE 7
Basic Board Mount Pressure Sensors, ABP Series TABLE 7. PRESSURE RANGE SPECIFICATIONS (CONTINUED) PRESSURE PRESSURE RANGE RANGE PMAX. (SEE FIGURE 3.) PMIN.
PAGE 8
Basic Board Mount Pressure Sensors, ABP Series FIGURE 5. DIP PACKAGE DIMENSIONAL DRAWINGS (FOR REFERENCE ONLY: MM [IN].) DIP NN: No port 8,0 [0.32] 7,3 [0.29] 2,54 Typ. [0.100] 4,0 [0.16] 4 5 3,23 Wet media [0.127] 2,95 Dry media [0.116] 6 6 5 4 1 2 3 2X 1,45 [0.057] 5,5 [0.22] 6,3 [0.25] 3 2 11,0 [0.43] 11,5 [0.45] 1,0 [0.04] 1 0,25 Typ. [0.010] 8,6 [0.34] 3,81 [0.150] 6X 0,46 [0.018] DIP AN: Single axial barbed port 8,0 [0.32] 7,3 [0.29] 4,0 [0.16] 4 5 7,00 [0.
PAGE 9
Basic Board Mount Pressure Sensors, ABP Series FIGURE 5. DIP PACKAGE DIMENSIONAL DRAWINGS (CONTINUED) DIP LN: Single axial barbless port 8,0 [0.32] 7,3 [0.29] 4,0 [0.16] 4 5 2,54 Typ. [0.100] 3,23 Wet media [0.127] 2,95 Dry media [0.116] 4,80 [0.189] 6 6 5 4 2X 1,45 [0.057] 5,5 [0.22] 6,3 [0.25] 3 2 ø5,00 2,68 [0.197] [0.106] 11,5 [0.45] 1,0 [0.04] 1 11,0 [0.43] 1 0,25 Typ. [0.010] 8,6 [0.34] 2 3 6X 0,46 [0.018] 3,81 [0.150] 6X 0,46 [0.
PAGE 10
Basic Board Mount Pressure Sensors, ABP Series FIGURE 5. DIP PACKAGE DIMENSIONAL DRAWINGS (CONTINUED) DIP JJ: Dual radial barbless ports, same side 0,7 [0.03 4 2X 4,0 [0.16] 5 8,0 [0.32] 2,54 Typ. [0.100] 3,38 Wet media [0.133] 3,10 Dry media [0.122] 2,82 [0.111] 6 6 Port 1 5 2X 1,47 [0.058] 4 2X 4,65 [0.183] 4,45 [0.175] 6,3 [0.25] 2,10 [0.083] 11,0 [0.43] 11,5 [0.45] Port 1 2X ø1,88 [0.074] Port 2 Port 2 3 7,3 [0.29] 2 1,0 [0.04] 1 4,45 [0.175] 1 0,25 Typ. [0.010] 8,6 [0.
PAGE 11
Basic Board Mount Pressure Sensors, ABP Series FIGURE 6. SMT PACKAGE DIMENSIONAL DRAWINGS (FOR REFERENCE ONLY: MM [IN].) SMT NN: No port 7,3 [0.29] 4,0 [0.16] 4 5 6 8.0 [0.32] 0,25 Typ. [0.010] 3,23 Wet media [0.127] 2,95 Dry media [0.116] 6 5 4 5,5 [0.22] 6,3 [0.25] 11,0 [0.43] 11,5 [0.45] 6X 1,28 [0.050] 3 SMT AN: Single axial barbed port 2 1,0 [0.04] 1 7,3 [0.29] 4,0 [0.16] 4 6X 0,46 [0.018] 4,2 [0.17] 7,00 [0.276] 5 1 2 3 2X 1,45 [0.057] 2,54 Typ. [0.100] 3,63 Wet media [0.
PAGE 12
Basic Board Mount Pressure Sensors, ABP Series FIGURE 6. SMT PACKAGE DIMENSIONAL DRAWINGS (CONTINUED) SMT JJ: Dual radial barbless ports, same side 2X 4.65 [0.183] 4 5 6 8,0 [0.32] 2,54 Typ. [0.100] 2,82 [0.111] 3,38 Wet media [0.133] 3,10 Dry media [0.122] 0,7 [0.03] 2X 4.0 [0.16] 2X 1,45 [0.057] 6 5 5,06 Wet media [0.199] 4,78 Dry media [0.188] 4 4.45 [0.175] Port 1 2,10 [0.083] 6,3 [0.25] Port 2 Port 1 11,5 [0.45] 2X 1,88 [0.074] 11,0 [0.43] 4,45 [0.175] Port 2 3 2 7,3 [0.
PAGE 13
Basic Board Mount Pressure Sensors, ABP Series FIGURE 7. LEADLESS SMT PACKAGE DIMENSIONAL DRAWINGS (FOR REFERENCE ONLY: MM [IN].) Leadless SMT NN: No port 4.0 [0.16] 2 1 3,23 Wet media [0.13] 3 3.5 [0.14] 5 4.0 [0.16] 2 1 7,0 6X 1,25 [0.28] [0.049] 1,0 [0.04] 7,0 [0.28] 3 3.5 [0.14] 3,63 Wet media [0.14] 3,35 Dry media [0.13] 6,3 ø2,74 [0.25] [0.108] Leadless SMT LN: Single axial barbless port 1 4.0 [0.16] 2 1,5 [0.06] 2 1 7,0 6X 1,25 [0.28] [0.049] 4 2,5 Typ. [0.10] 4 5 6 8,0 [0.
PAGE 14
ADDITIONAL MATERIALS WARRANTY/REMEDY The following associated literature is available at sensing.honeywell.com: Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicable warranty period. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgment or consult your local sales office for specific warranty details.