Programming Manual

ManualsBrandsHoneywell ManualsSecurity SystemHoneywell Ademco VISTA-20P

MISCELLANEOUS SYSTEM FIELDS (*174-*181)

∗

∗∗

∗174 Clean Me Reporting Options [0]

(for ESL smoke detectors)

0 = disable; 1 = Clean Me signal reports;

NOTE:

If Clean Me is enabled, you must enter “3” in field ✱56

programming for zone 1 response time.

∗

∗∗

∗177 Device Duration 1, 2 [0] [0]

(used in *80 Menu mode-Device Actions 5/6) 1 2

0 = 15 seconds 6 = 2-1/2 min #+11 = 7 min

1 = 30 seconds 7 = 3 min #+12 = 8 min

2 = 45 seconds 8 = 4 min #+13 = 10 min

3 = 60 seconds 9 = 5 min #+14 = 12 min

4 = 90 seconds #+10 = 6 min #+15 = 15 min

5 = 2 minutes

∗

∗∗

∗181 50/60 Hertz AC Operation [0]

0 = 60 Hz; 1 = 50 Hz

CONFIGURABLE ZONE TYPE OPTIONS (*182-*185)

(see Configurable Zone Type Worksheet on page 7)

∗

∗∗

∗182 Configurable Zone Type 90

1 2 3 4 5 6 7 8 9 10

Enter the appropriate value for each entry, 1-10, based on the charts

provided on the next page. Each entry is the sum of the values of its

selected options

(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

∗

∗∗

∗183 Zone Type 90 Report Codes

IMPORTANT: Use existing Contact ID® codes, if appropriate, or

define unique codes in CID code range 750-789. See important note

in installation instructions.

90 ALARM ID: XXX

TROUBLE ID: XXX

Enter the desired 3-digit Contact ID® report codes for alarms and

troubles occurring on zones assigned to this zone type. Enter the

codes sequentially (all 6 digits). When entering digits, [#] moves

cursor back, [∗] moves forward. Press [∗] when done to continue.

∗

∗∗

∗184 Configurable Zone Type 91

1 2 3 4 5 6 7 8 9 10

Enter the appropriate value for each entry, 1-10, based on the charts

provided on the next page. Each entry is the sum of the values of its

selected options

(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

∗

∗∗

∗185 Zone Type 91 Report Codes

IMPORTANT: Use existing Contact ID® codes, if appropriate, or

define unique codes in CID code range 750-789. See important note

in installation instructions.

91 ALARM ID: XXX

TROUBLE ID: XXX

Enter the desired 3-digit Contact ID® report codes for alarms and

troubles occurring on zones assigned to this zone type. Enter the

codes sequentially (all 6 digits). When entering digits, [#] moves

cursor back, [∗] moves forward. Press [∗] when done to continue.

∗

∗∗

∗189 AUI Device 1 and 2 Enable [1] [1]

(for Touch Screen Style Keypads)

AUI 1 AUI 2

System supports up to two touch screen style keypads (e.g., Symphony

Advanced User Interface, and 6270 Touch Screen Keypad).

AUI Compatibility Note: To ensure proper AUI device operation,

connect only to controls having microprocessor version 3.0 or higher,

and use AUI devices with the following rev levels: 6270 series use

version 1.0.9 or higher; 8132/8142 (Symphony) series use version

1.1.175 or higher.

Touch Screen (AUI) device 1: Must set AUI device address to 1

Touch Screen (AUI) device 2: Must set AUI device address to 2

VISTA-20P: Enter each touch screen keypad’s home partition

0 = disable; 1 = partition 1; 2 = partition 2; 3 = partition 3 (common)

VISTA-15P: 0 = disable; 1 = enable

NOTE: Use of touch screen style keypads does not affect the number

of standard keypads supported.

KEYPAD OPTIONS *190-*196

NOTES: 1. Options for keypad address 16 are set by the factory and cannot

be changed.)

2. Each keypad must be assigned a unique address. Keypads

programmed with the same address will give unpredictable results.

∗

∗∗

∗190 Keypad 2 Device Address 17 [0] [0]

†Partition/Enable: Part./ Sound

VISTA-20P: Enter partition where: Enable

†

0 = keypad disabled; 1-3 = part. no. (3 = com)

VISTA-15P: 1 = enable; 0 = disable

Sound: 0 = no suppression

1 = suppress arm/disarm and E/E beeps

2 = Suppress chime beeps only

3 = suppress arm/disarm, E/E, and chime beeps

∗

∗∗

∗191 Keypad 3 Device Address 18 [0] [0]