Product Manual

ManualsBrandsHoneywell ManualsGas MonitoringGas Monitor

BW Clip

2 OR 3 YEAR H

S, CO, O

, SO

SINGLE-GAS DETECTOR

Part Number 50115903-067 | OM-EN-PALO-A8 | BW Clip Operator Manual

BW Clip is a portable, single-gas detector manufactured by

BW Technologies by Honeywell (BW). BW Clip continuously measures the

concentration of a specific gas in the ambient environment, and activates an alarm

when concentrations exceed alarm setpoints. It is your responsibility to respond

appropriately to the alarms.

BW Clip is a member of the GasAlert family of products. It is compatible with

IntelliDoX and MicroDock II automatic test and calibration stations, as well as Fleet

Manager II software version 4.0 or higher. For more information, visit the product

website at www.honeywellanalytics.com

Safety Information: Read First

1. Substitution of components may impair Intrinsic Safety.

2. Periodically test the response of the sensor by exposing the detector to a

target gas concentration that exceeds the low alarm setpoint. Manually verify

that the audible and visual alarms are activated.

3. Detectors in hibernation mode are not functional.

1. Activate the detector before the activation date on the package.

2. This product is a gas detector, not a measurement device.

3. Ensure that the sensor grill is free of dirt, debris, and is not obstructed.

4. Clean the exterior with a soft, damp cloth.

5. Bump test the detector in a normal atmosphere that is free of hazardous gas.

6. For optimal performance, periodically zero the sensor in a normal atmosphere

(20.9% v/v O

) that is free of hazardous gas.

Informations de sécurité – À lire au préalable

AVERTISSEMENT

Le remplacement d’un composant de l’appareil peut compromettre la sécurité

intrinsèque du détecteur.

Testez périodiquement la réponse du capteur en exposant le détecteur à une

concentration de gaz supérieure au seuil d’alarme basse. Vérifiez manuellement

que les alarmes sonores et visuelles sont activées.

3. Détecteurs en mode veille prolongée ne sont pas fonctionnels.

MISE EN GARDE

1. Activez le détecteur avant la date d’activation sur l’emballage.

2. Ce produit est un détecteur de gaz, pas un dispositif de mesure.

3. Veillez à assurer que la grille du capteur est exempt de saleté, les

débris, et ne soit pas obstrué.

4. Nettoyez l’extérieur de l’appareil à l’aide d’un chiffon doux et humide.

5. Veillez à effectuer un test fonctionnel du capteur dans une atmosphère normale

qui est exempte de gaz dangereux

6. Pour des performances optimales, zéro périodiquement le capteur dans une

atmosphère normale (20,9% v/v O

) qui est exempte de gaz dangereux.

BW Clip Factory Calibration Certificate

This instrument was factory inspected, tested and calibrated in accordance with the conditions and

requirements of our registered Quality System, Operating Standards and Sales Agreements.

Getting Started

PushbuttonPushbutton

Sensor and

sensor grill

Sensor and

sensor grill

Bubble label

with product name

and gas type

Bubble label

with product name

and gas type

Audible

alarm

Audible

alarm

LCDLCD

LED

visual alarms

LED

visual alarms

Infrared port

Alligator

clip

Product label

LCD and Symbols

Pushbutton prompt. When this symbol is displayed, press

and hold the pushbutton until the symbol disappears.

BW Clip O

models only. Oxygen concentration is

measured as percent by volume.

BW Clip H

S, CO and SO

models only. Toxic gas

concentration is measured in parts per million.

Low alarm and high alarm. These symbols are

displayed when a gas concentration that exceeds alarm

setpoints is detected.

Non-compliance warning. This symbol is displayed when a

diagnostic or compliance test fails; when the operating life

countdown reaches 24 hours or less; and for up to 30 days

after operating life expiry. It is also displayed when certain

notifications are enabled through Fleet Manager II via an

IntelliDoX station.

Real-time clock. This symbol is displayed when real-time

clock is enabled through Fleet Manager II via an IntelliDoX

station.

End of operating life warning. This symbol is displayed when

the operating life countdown reaches 24 hours or less.

Peak reading. This symbol is displayed when a maximum gas

exposure event has occurred within the past 24 hours.

Operating life remaining in months (MM) or days (DD).

a WARNING

a CAUTION

Bump test reminder. If the detector is configured to

display a

bump test reminder, this symbol is displayed when a bump

test is due.

indicates a failed test.

BW Clip O

models only. This symbol is displayed when more

than 24 hours have elapsed since the last

successful zero

procedure was performed. indicates a failed test.

Summary of content (4 pages)

PAGE 1
BW Clip 2 OR 3 YEAR H2S, CO, O2, SO2 SINGLE-GAS DETECTOR Part Number 50115903-067 | OM-EN-PALO-A8 | BW Clip Operator Manual BW Clip is a portable, single-gas detector manufactured by BW Technologies by Honeywell (BW). BW Clip continuously measures the concentration of a specific gas in the ambient environment, and activates an alarm when concentrations exceed alarm setpoints. It is your responsibility to respond appropriately to the alarms. BW Clip is a member of the GasAlert family of products.
PAGE 2
BW Clip 2 OR 3 YEAR H2S, CO, O2, SO2 SINGLE-GAS DETECTOR Activate a New Detector 1. Move to a normal atmosphere (20.9% v/v O2) that is free of hazardous gas. 2. Press and hold the pushbutton until a 5 second countdown is displayed, and then continue to hold until the countdown is complete. 3. When the countdown is complete, the LCD and LEDs turn on and then turn off. The detector performs an internal diagnostic test. 4.
PAGE 3
Recall Events and Settings When the detector is in normal operating mode, press the pushbutton at any time to scroll through events and settings that are not empty or disabled through Fleet Manager II via an IntelliDoX station. Events and settings are displayed in this order: 1. Peak Reading, if available, and when a maximum gas exposure event has occurred within the past 24 hours. 2. Time of Peak Reading, if Real-time Clock display is enabled. 3. Low Alarm Setpoint 4. High Alarm Setpoint 5.
PAGE 4
BW Clip 2 OR 3 YEAR H2S, CO, O2, SO2 SINGLE-GAS DETECTOR About this Publication This publication is an operator guide for BW Clip portable single-gas detectors manufactured by BW Technologies by Honeywell. It is intended for use with the following models: • 24- and 36-month H2S and CO Detectors • 24-month O2 detector • 24-month SO2 detector Copyright, Notice, Trademarks Use Fleet Manager II via an IntelliDoX station to adjust alarm setpoints.