Model Modèle Modelo Jig Saw Scie sauteuse Sierra de calar CJ 110MV • CJ 110MVA CJ110MV CJ110MVA SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool.
English CONTENTS Page Page IMPORTANT SAFETY INFORMATION ................... 3 MEANINGS OF SIGNAL WORDS ........................... 3 ASSEMBLY AND OPERATION .................................. 10 APPLICATIONS ...................................................... 10 PRIOR TO OPERATION .......................................... 10 CUTTING ................................................................ 13 CONCERNING CUTTING OF STAINLESS STEEL PLATES ...................................................
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. 2. 3. 4 Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
English 4. 5. (3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. (4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. (5) Do not overreach. Keep proper footing and balance at all times.
English SPECIFIC SAFETY RULES AND SYMBOLS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 6 Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. ALWAYS wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss.
English 15. Operate power tools at the rated voltage. Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out. 16. NEVER use a tool which is defective or operating abnormally.
English DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words “Double insulation” appear on the power tool or on the nameplate.
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safey instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.
English ASSEMBLY AND OPERATION APPLICATIONS 䡬 䡬 䡬 䡬 䡬 Cutting various lumber and pocket cutting Cutting mild steel plate, aluminum plate, and copper plate Cutting plastics, such as phenol resin and vinyl chloride Cutting thin and soft construction materials Cutting stainless steel plate (With No. 97 blade) PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate. 2.
English 6. Changing blades Blade (1) Open the lever up to the stop. (Fig. 3-I) (2) Remove fitted blade (3) Insert new blade up to the stop in the balde holder. (Fig. 3-II) (4) Close the lever. (Fig. 3-III) Blade holder CAUTION: 䡬 䡬 Lever Be sure to switch power OFF and disconnect the plug from the receptacle when changing blades. Do not open the lever when plunger is moving. Fig. 3 Blade NOTE: 䡬 Confirm the protrusions of blade inserted to the blade holder surely. (Fig.
English (2) For the hard material, such as a steel plate, etc., decrease the orbital operation. For the soft material, such as lumber, plastic, etc., increase the orbital operation to increase work efficiency. To cut the material accurately, decrease the orbital operation. 9. Cutting stainless steel plates This Jig Saw can cut stainless steel plates by using No. 97 blade. Carefully read “Concerning cutting of stainless steel plates” for proper operation. Change knob Fig. 7 10.
English Base bolt CUTTING Base CAUTIONS: 䢇 In order to prevent blade dislodging, damage or excessive wear on the Plunger, please make sure to have surface of the base plate attached to the work piece while sawing. Allen wrench 1. Rectilinear cutting (1) (2) (3) (4) When cutting on a straight line, first draw a marking gauge line and advance the saw along that line. Using the guide (sold separately) will make it possible to cut accurately on a straight line.
English 4. Cutting metallic materials (1) Adjust the speed Dial between scales “3” and “4”. (2) Set the orbital position to “0” or “I”. (3) Always use an appropriate cutting fluid (spindle oil, soapy water, etc.). When a liquid cutting fluid is not avaiable, apply grease to the back surface of the material to be cut. 5. Pocket cutting (1) In lumber Aligning the blade direction with the grain of the wood, cut step by step until a window hole is cut in the center of the lumber. (Fig.
English When cutting stainless steel plates, adjust the unit as described below: 1. Adjust the speed Blade Thickness of material No. 97 1/16" – 5/32" (1.5 mm – 2.5 mm) Dial Scale Middle groove position between scales “2” and “3” NOTE: Dial scale reading is for reference only. The higher the speed is, the quicker the material is cut. But the service life of the blade will be reduced in this case. When the speed is too low, cutting will take longer, although the service life will be prolonged.
English CONNECTING WITH CLEANER Adapter Nose By connecting with cleaner (sold separately) Chip through dust collection adapter and adapter (sold cover Cleaner separately), most of dust can be collected. (1) Remove the allen wrench from the base. (2) Move the base fully forward. (Fig. 10, 11) Base Dust collection (3) Attach the chip cover. adapter (4) Connect the dust collection adapter with Fig. 18 adapter. (Fig. 18) (5) Connect the adapter with the nose of cleaner. Notch (Fig.
English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted. 2. Inspecting the screws Regularly inspect all screws and ensure that they are properly tightened.
Mild steel plate Plywood Fiberboard Hardboard Below 3/8 (10) 3/16–1-3/16 (5–30) No. 16 No. 21 No.
English ACCESSORIES WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les zones sombres invitent aux accidents.
Français (2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher les cheveux longs. Tenir ses cheveux, vêtements et ses gants éloignés des parties mobiles. Les vêtements larges, les bijoux et les cheveux longs peuvent se prendre dans les parties mobiles. (3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation est sur la position d’arrêt avant de brancher la machine.
Français (2) Lors de la réparation d’un outil, utiliser uniquement des pièces de rechange identiques. Suivre les instructions de la section d’entretien de ce mode d’emploi. L’utilisation de pièces non autorisées ou un non respect des instructions d’entretien peut créer un risque d’électrocution ou de blessures. REGLES DE SECURITE SPECIFIQUES ET SYMBOLES 1.
Français 11. Maintenir toutes les vis, tous les boulons et les couvercles fermement en place. Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier leurs conditions périodiquement. 12. Ne pas utiliser les outils motorisés si le revêtement de plastique ou la poignée est fendu. Des fentes dans le revêtement ou la poignée peuvent entraîner une électrocution. De tels outils ne doivent pas être utilisés avant d’être réparé. 13.
Français 22. Cette machine utilise un moteur à puissance élevée. Si la machine est utilisée continuellement à faible vitesse, une charge supplémentaire est appliquée au moteur et peut en provoquer son mauvais fonctionnement. Toujours utiliser la scie de façon à ne pas coincer la lame dans la pièce lors de son usage. Toujours régler la vitesse de la lame pour permettre une coupe en douceur. 23. Définitions pour les symboles utilisés sur cet outil V ............ volts Hz .......... hertz A ............
Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français ASSEMBLAGE ET FONCTIONNEMENT APPLICATIONS 䡬 䡬 䡬 䡬 䡬 Coupe de différentes sortes de bois de charpente et découpe d’ouvertures Coupe de plaques en acier doux, plaques en aluminium et en cuivre Coupe de résines synthétiques comme résine phénolique et chlorure de vinyl Coupe de matériaux de construction peu épais et tendres Coupe de plaque dácier inoxydable (avec la lame No. 97) AVANT L’UTILISATION 1.
Français 6. Remplacement des lames Lame (1) Ouvrir le levier jusqu’à la butée. (Fig. 3-I) (2) Retirer la lame. (3) Insérer la nouvelle lame jusqu’à la butée dans le support de lame. (Fig. 3-II) (4) Refermer le levier. (Fig. 3-III) Support de lame PRECAUTIONS: Levier 䡬 Bien mettre l’interrupteur sur OFF et d ébrancher la fiche de la prise secteur avant de remplacer les lames. 䡬 Ne pas ouvrir le levier pendant que le plongeur bouge. Fig.
Français (2) Pour les matériaux durs, tels que plaques d’acier, etc., réduire le fonctionnement orbital. Pour les matériaux moux, tels que bois de charpente, matières plastiques, etc., augmenter le fonctionnement orbital pour acroître le rendement du travail. Pour couper les matériaux avec précision, réduire le fonctionnement orbital. 9. Découpage inoxydable de plaques en acier Bouton de changement Fig.
Français 13. Allumer la lampe PRECAUTION: Ne fixez pas la lumière ou la source de lumière directement. Pour allumer la lampe, appuyez sur la gâchette. Pour l’éteindre, relâchez la gâchette. COUPE Boulon de la Base base PRECAUTION: 䢇 Pour éviter un délogement de la lame, des dommages ou une usure excessive du plongeur, bien fixer la surface de la plaque du socle à la pièce pendant le sciage. 1.
Français 3. Coupe d’un cercle ou d’un arc circulaire Le guide est également utile pour la coupe en cercle. Après avoir fixé le guide de la même façon qu’expliqué ci-dessus, faire passer le clou ou la vis dans la pièce par l’orifice du guide, puis l’utiliser comme axe pour la coupe. (Fig. 13) REMARQUE: La coupe en cercle doit être effectuée avec la lame placée environ à la verticale par rapport à la surface du fond de la base. Clou ou vis Guide Orifice de guidage Fig. 13 4.
Français AU SUJET DU DECOUPAGE DE PLAQUES EN ACIER INOXYDABLE Avec la lame No. 97, il sera possible de couper des tôles d’acier inoxydable. Pour le réglage de l’outil, noter les points suivants. PRECAUTION: 䢇 Pour éviter un délogement de la lame, des dommages ou une usure excessive du plongeur, bien fixer la surface de la plaque du socle à la pièce pendant le sciage. En coupant des plaques en acier inoxidable, régler l’appareil de la façon suivante. 1. Pour régler la vitesse Lame No.
Français RANGEMENT DES LAMES DE LA CLÉ ALLEN 䡬 I Il est possible de ranger la clé allen dans la base (voir Fig. 17). Clé allen II Base Fig. 17 RACCORDEMENT AU NETTOYEUR Adaptateur Si l’on raccorde le nettoyeur (vendu séparément) par le adaptateur pour collecteur de poussière et Bec l’adaptateur (vendus séparément), on pourra Couvercle Nettoyeur recueillir la plus grande partie des poussières. d’éclats (1) Retirer la clé allen de la base. (2) Déplacer la base à fond vers l’avant. (Fig.
Français ENTRETIEN ET INSPECTION AVERTISSEMENT: S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspectio. 1. Contrôle du foret de perçage Etant donné que l’utilisation d’une mèche usée entraînera un mauvais fonctionnement du moteur et une diminution de l’efficacité, remplacez la mèche usée par une neuve ou aiguisez-la immédiatement et dès que vous notez une certaine usure. 2.
Panneau fibreux Isorel 1/8–63/64 (3–25) Moins 1/4(6) Moins 1/4(6) 1/8–1-1/2 (3–40) 1/8–1-1/2 (3–40) 1/8–3/4 (3–20) Moins 1/4(6) 1/8–3/4 (3–20) 1/8–63/64 (3–25) 3/16–63/64 (5–25) 3/16–19/32 (5–15) 3/16–19/32 (5–15) Hauteur allant jusqu’à 63/64(25) Moins 3/16(5) 1/16–5/32 (1,5–2,5) 5/64–3/16 (2–5) No. 97 REMARQUE: 䡬 Le rayon de coupe minimal des lames No. 1 (Long), No. 1 (Super Long), No. 21, No. 22 et No. 41 est de 100 mm. 䡬 Les lames No. 1 (Long), No. 1 (Super Long), No. 11, No. 12, No.
Français ACCESSOIRES AVERTISSEMENT: TOUJOURS utiliser UNIQUEMENT des pièces de rechange et des accessoires HITACHI. Ne jamais utiliser de pièce de rechange ou d’accessoires qui ne sont pas prévus pour être utilisé avec cet outil. En cas de doute, contacter HITACHI pour savoir si une pièce de rechange ou un accessoire particulier peuvent être utilisés en toute sécurité avec votre outil.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los bancos de trabajo desordenados y las áreas obscuras pueden conducir a accidentes.
Español (2) Vístase adecuadamente. No utilice ropa floja ni joyas. Si tiene pelo largo, recójaselo. Mantenga su pelo, ropa, y guantes alejados de las partes móviles. La ropa floja, las joyas, o el pelo largo pueden engancharse en las partes móviles. (3) Evite la puesta en marcha accidental. Cerciórese de que la alimentación de la herramienta eléctrica esté desconectada antes de enchufarla en una toma de la red.
Español (2) Para el servicio de mantenimiento o reparación de una herramienta, utilice solamente piezas de repuesto idénticas. Siga las instrucciones de la sección de mantenimiento de este manual. La utilización de piezas no autorizadas, o el no seguir las indicaciones del Manual de instrucciones puede crear el riesgo de descargas eléctricas u otras lesiones. NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD 1.
Español 11. Mantenga todos los tornillos, pernos, y cubiertas firmemente fijados en su lugar. Mantenga todos los tornillos, pernos, y cubiertas firmemente montados. Compruebe periódicamente su condición. 12. No utilice herramientas eléctricas si la carcasa o la empuñadura de plástico está rajada. Las rajas en la carcasa o en la empuñadura de plástico pueden conducir a descargas eléctricas. Tales herramientas no deberán utilizarse mientras no se hayan reparado. 13.
Español 22. Esta máquina emplea un motor de gran potencia. Si la utiliza continuamente a baja velocidad, el motor recibirá una carga extra que puede provocar el agarrotamiento del mismo. Utilice siempre esta herramienta eléctrica de forma que la cuchilla no quede atascada en la pieza serrada durante la operación. Ajuste siempre la velocidad de la cuchilla de forma que se logre un serrado uniforme. 22. Definiciones para los símbolos utilizados en esta herramienta V ............ voltios Hz ..........
Español AISLAMIENTO DOBLE PARA OFRECER UNA OPERACIÓN MÁS SEGURA Para garantizar una operación más segura de esta herramienta eléctrica, HITACHI ha adoptado un diseño de aislamiento doble. “Aislamiento doble” significa que se han utilizado dos sistemas de aislamiento físicamente separados para aislar los materiales eléctricamente conductores conectados a la fuente de alimentación del bastidor exterior manejado por el operador.
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica.
Español MONTAJE Y OPERACIÓN APLICACIONES Cortar diversas maderas útiles y recorte interior Cortar placa de acero pobre en carbono, aluminio y cobre Cortar resinas sintéticas como resina de fenol y clorulo de vinilo Cortar materiales de construcción delgados y blandos Corte de chapas de acero inoxidable (con cuchilla No. 97) ANTES DE LA OPERACIÓN 1.
Español 6. Cambio de las cuchillas Cuchilla (1) Abra la palanca hacia arriba, hasta el tope. (Fig. 3-I) (2) Desmonte la cuchilla. (3) Inserte la cuchilla nueva hasta el tope del portacuchilla. (Fig. 3-II) (4) Cierre la palanca. (Fig. 3-III) Portacuchilla Palanca PRECAUCION: Cuando cambie las cuchillas, asegúrese de desconectar (OFF) la alimentación y de desenchufar la clavija del tomacorriente. No abra la palanca mientras se está moviendo el émbolo. Fig.
Español (2) Para materiales duros como por ejemplo, chapas de acero, etc., disminuir el funcionamiento orbital. Para materiales blandos como por ejemplo, madera, plásticos, etc., aumentar el funcionamiento orbital para incrementar la eficiencia de trabajo. Para cortar el material de forma precisa, disminuir el funcionamiento orbital. 9. Corte de chapas de acero inoxidable Esta sierra caladora corta las placas de acero inoxidable utilizando cuchilla N° 97.
Español 13. Encendido de la lámpara PRECAUCIÓN: No mire directamente a la luz ni a la fuente de luz. Para encender la lámpara, tire del gatillo. Suelte el gatillo para apagarla. Perno de base Base CORTAR PRECAUCION: Mientras esté serrando, para evitar que la cuchilla se salga o que el pistón se estropee o se desgaste demasiado, asegúrese de que la superficie de la placa base esté en contacto con la pieza de trabajo. 1.
Español 3. Cortar en circulo o un arco circular La guía también podrá ser útil para el corte circular. Después de fijar la guía de la manera indicada arriba, introduzca el clavo o el tornillo en el material a través del orificio de la guía, y luego utilícelo como eje durante el corte. (Fig. 13) NOTA: El corte circular se puede realizar con la cuchilla colocada de forma aproximadamente vertical con respecto a la superficie inferior de la base. Clavo o tornillo Guía Orificio de guía Fig. 13 4.
Español SOBRE EL CORTE DE CHAPAS DE ACERO INOXIDABLE Cuando utilice la cuchilla núm. 97, podrá cortar chapas de acero inoxidable. Tenga en cuenta lo siguiente para ajustar la unidad. PRECAUCION: Mientras esté serrando, para evitar que la cuchilla se salga o que el pistón se estropee o se desgaste demasiado, asegúrese de que la superficie de la placa base esté en contacto con la pieza de trabajo. Para cortar chapas de acero inoxidable, ajuste la sierra como se describe a continuación. 1.
Español I ALOJAMIENTO DE LA LLAVE ALLEN Llave allen Es posible alojar la llave allen en la base (consulte la Fig. 17). II CONEXION CON EL LIMPIADOR Conectando con el limpiador (en venta Base separadamente) a través del adaptador de extracción de polvos y el adaptador (en venta Fig. 17 separadamente), se podrá recolectar casi la totalidad del polvo. (1) Retire la llave allen de la base. Adaptador (2) Mueva la base completamente hacia adelante. Cubierta Punta (Figs.
Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de desconectar la alimentación y de desenchufar el cable de alimentación del tomacorriente. 1. Inspeccionar la broca de taladro Debido a que el uso de brocs desafiladas pueden causar mal funcionamiento del motor y desmejorar la eficacia del taladro, hay que reemplazar las brocas en malas condiciones por nuevas o afilarlas de inmediato al advertir abrasión. 2.
Lista de cuchillas apropiadas 1/8–63/64 (3–25) Menos 1/4(6) Menos 1/4(6) 1/8–1-1/2 (3–40) 3/8–2-5/32 (10–55) 3/8–2-5/32 1/8–63/64 (10–55) (3–25) 1/8–3/4 (3–20) Menos 1/4(6) 1/8–1-1/2 (3–40) 3/16–1-3/16 (5–30) 3/16–19/32 (5–15) 3/8–2-5/32 1/8–63/64 3/16–63/64 1/8–63/64 3/8–2-5/32 (10–55) (3–25) (5–25) (3–25) (10–55) Menos 3/16(5) Menos 1/4(6) Menos 1/8(3) 1/8–63/64 (3–25) 3/16–63/64 (5–25) 3/16–19/32 (5–15) 3/16–19/32 (5–15) Altura hasta 63/64(25) Menos 3/16(5) 1/16–5/32 (1,5–2,5) 5/64
Español ACCESORIOS ADVERTENCIA: UTILICE únicamente repuestos y accesorios autorizados por HITACHI. No utilice nunca repuestos o accesorios no previstos para usar con esta herramienta. Si tiene dudas en cuanto a la seguridad de usar determinado repuesto o accesorio junto con su herramienta, póngase en contacto con HITACHI. La utilización de otros accesorios puede resultar peligrosa y causar lesiones o daños mecánicos. NOTA: Los accesorios están sujetos a cambio sin ninguna obligación por parte de HITACHI.
Item Part Name Q’TY No. 1 HOUSING (A).(B) SET 1 2 SUPPORT (B) 1 PRINTED CIRCUIT BOARD 1 3 (LED LIGHT) SWITCH (E) (1P SCREW TYPE) 1 4 W/LOCK MACHINE SCREW (W/WASHER) 4 5 M3.
Item Part Name Q’TY No. 1 HOUSING (A).(B) SET 1 2 SUPPORT (B) 1 PRINTED CIRCUIT BOARD 1 3 (LED LIGHT) 4 TERMINAL M3.5 1 5 CONTROLLER 1 6 O-RING (P-6) 4 TAPPING SCREW (W/FLANGE) 7 7 D4 × 20 (BLACK) 8 NAME PLATE 1 9 TERMINAL 2 10 CORD ARMOR 1 11 CORD CLIP 1 TAPPING SCREW (W/FLANGE) 2 12 D4 × 12 13 SLIDE BAR 1 14 CONNECTOR 50091 1 MACHINE SCREW (W/WASHER) 4 15 M3.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.