2 3 4 5 6 7 AUTO CM701..................................2-6 CM707................................
CM701 - USER GUIDE Description Features The Honeywell CM701 is a programmable room thermostat designed to control your heating system efficiently, providing comfortable temperatures when you are at home and energy savings when you are away. The following instructions explain how to program and use the thermostat to provide the most home comfort at the least cost. • Ergonomic user interface featuring an ‘OK-button’. • Large LCD (Liquid Crystal Display) Screen with backlight.
SETTING-UP THE CM701 ‘Getting Started’ This section shows you how to setup and run the thermostat in 3 simple steps: STEP 1: Installing the Batteries Note: Please follow the instructions in this section only if the thermostat screen is blank (no symbols or digits are displayed). If the room temperature is already displayed move on to Step 2: Setting the Date and Time. To install the Batteries: a. Lift up the front cover of the thermostat to reveal the battery cover and product controls. b.
‘Efficient Daily Use’ PROGRAMMING THE CM701 The Built-in Heating Program The built-in heating program has 4 temperature level changes that can be set between 3.00am and 2.50am the following day - allowing you to maintain the evening temperature after midnight. Each temperature level can be set between 5°C and 35°C, and adjusted in 0.5°C increments. The factory default program for heating is as follows.
‘Using the Features’ OPERATING THE CM701 Choosing the Operating Mode The thermostat can operate in three different modes: Automatic, Manual or Off. To set the operating mode press either of the AUTO, MAN or OFF buttons. The screen indicates which mode is currently active by displaying AUTO, MAN or OFF. • AUTO (automatic) mode sets the thermostat to follow the built-in temperature program (default or personalised).
‘Using the Features’ OPERATING THE CM701 Using the Special Features • Display Backlight The CM701 has a backlit display that will illuminate when a button is pressed for easier viewing of the display in low light conditions. • SERVICE indicator Note: This option only works if activated by your installer. The 'SERVICE' indicator is displayed at set intervals as a reminder that your heating system requires a routine check. Please call your installer to arrange a maintenance visit.
TROUBLESHOOTING THE CM701 Symptom Remedy Blank Display (Power Loss). Check batteries are installed by removing the battery cover. Check batteries have been installed in the correct orientation. Replace the batteries. Display shows flashing symbol. The batteries in the thermostat are low on power - Replace the batteries. Display shows A fault has occurred in your heating system. Remove and re-insert the batteries. symbol. If the symbol does not clear after a few minutes contact your installer.
CM707 - USER GUIDE Description Features The Honeywell CM707 is a programmable room thermostat designed to control your heating system efficiently, providing comfortable temperatures when you are at home and energy savings when you are away. The following instructions explain how to program and use the thermostat to provide the most home comfort at the least cost. • Ergonomic user interface featuring an ‘OK-button’. • Large LCD (Liquid Crystal Display) Screen with backlight.
SETTING-UP THE CM707 ‘Getting Started’ This section shows you how to setup and run the thermostat in 3 simple steps: STEP 1: Installing the Batteries Note: Please follow the instructions in this section only if the thermostat screen is blank (no symbols or digits are displayed). If the room temperature is already displayed move on to Step 2: Setting the Date and Time. To install the Batteries: a. Lift up the front cover of the thermostat to reveal the battery cover and product controls. b.
‘Efficient Daily Use’ PROGRAMMING THE CM707 The Built-in Heating Program The built-in heating program has 4 temperature level changes per day that can be set between 3.00am and 2.50am the following day - allowing you to maintain the evening temperature after midnight. Each temperature level can be set between 5°C and 35°C, and adjusted in 0.5°C increments. The factory default program for heating is as follows.
PROGRAMMING THE CM707 ‘Efficient Daily Use’ f. i) Press the COPY DAY button to copy Monday’s program into Tuesday. The display will go blank apart from the ‘non flashing’ day indicator, which indicates the day copied and the ‘flashing’ target day to copy the program to. To accept this day press the green button. To select a different target day press the DATE/DAY button until the ‘flashing’ day indicator is under the required button.
‘Using the Features’ OPERATING THE CM707 During Normal Operation • Temperature Enquiry In AUTO, MAN and OFF operating modes the thermostat will display the current room temperature. To review the programmed ‘target’ temperature (the temperature which the button. This ‘target’ temperature value will be thermostat is trying to maintain) press the displayed flashing for 5 seconds before returning to the current room temperature value.
PROGRAMMING THE CM707 ‘Using the Features’ Using the Special Features • Display Backlight The CM707 has a backlit display that will illuminate when a button is pressed for easier viewing of the display in low light conditions. • SERVICE indicator (optional) Note: This option only works if activated by your installer. The 'SERVICE' indicator is displayed at set intervals as a reminder that your heating system requires a routine check. Please call your installer to arrange a maintenance visit.
TROUBLESHOOTING THE CM707 Symptom Remedy Blank Display (Power Loss). Check batteries are installed by removing the battery cover. Check batteries have been installed in the correct orientation. Replace the batteries. Display shows flashing symbol. The batteries in the thermostat are low on power - Replace the batteries. Display shows A fault has occurred in your heating system. Remove and re-insert the batteries. symbol. If the symbol does not clear after a few minutes contact your installer.
WHAT IS A PROGRAMMABLE ROOM THERMOSTAT? ...an explanation for householders A programmable room thermostat is both a programmer and a room thermostat. A programmer allows you to set ‘On’ and ‘Off’ time periods to suit your own lifestyle. A room thermostat works by sensing the air temperature, switching on the heating when the air temperature falls below the thermostat setting, and switching it off once this set temperature has been reached.
Honeywell Control Systems Ltd. Arlington Business Park, Bracknell Berkshire RG12 1EB Technical Help Desk: 08457 678999 42010941-007 R1 www.honeywelluk.com © 2006 Honeywell International Inc.
