Owner’s Manual CT31 Low-voltage Thermostat Getting started Check to make sure your package includes the following items: Wire labels Caution card Wall anchors and mounting screws (2 each) CT31 thermostat Cover plate Before you begin, make sure you have: • Screwdriver • Hammer • Level (optional) • Pencil • Drill bit (3/16” for drywall, 7/32” for plaster) ® U.S. Registered Trademark. Patents pending. Copyright © 2005 Honeywell International Inc. All rights reserved.
Owner’s Manual Remove your old thermostat 1 Turn off power at heating/cooling system (or fuse/circuit-breaker panel). 2 Remove cover and thermostat, but leave wallplate with wires attached. Leave wallplate in place Is there a sealed tube containing mercury? If so, see mercury notice below. Old thermostat Cover MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube.
CT31 Low-voltage Thermostat Label wires and remove old wallplate Use a screwdriver to disconnect wires one by one.As you disconnect each wire, wrap it with the label matching the letter on your old thermostat. (Adhesive labels are supplied in your thermostat package.) Remove the old wallplate only after all wires are labeled. Be careful not to let loose wires fall into the wall opening.
Owner’s Manual Mount thermostat base 1 Drill holes at pencil-marked locations (3/16” holes for drywall, 7/32” holes for plaster). 2 Use hammer to tap anchors into holes until flush with wall. 3 [Optional] Pull wires through cover plate (if needed to cover marks left by your old thermostat). 4 Pull wires through thermostat base and insert screws. Check level if desired, then tighten screws. Optional cover plate Thermostat base Connect wires 1 Match each labeled wire with same letter on terminal.
CT31 Low-voltage Thermostat Set adjustment lever 1 Separate cover from thermostat, and remove the plastic insert. 2 Use a pencil to move the adjustment lever to the proper setting for your system (see table below). Your system Setting Gas or oil furnace (less than 90% efficiency) 0.4 Electric furnace (any type) 0.3 High efficiency furnace (more than 90% efficiency) 0.8 Hot water system 0.8 Gas/oil steam or gravity system 1.
Owner’s Manual Operation Temperature setting Move lever to adjust desired indoor temperature. Fan switch System switch • On: Fan runs continuously. • • Auto: Fan runs only when heating or cooling system is on. Cool: Thermostat controls only the cooling system. • Heat: Thermostat controls only the heating system. • Off: Heating and cooling systems are off. CAUTION: EQUIPMENT DAMAGE HAZARD.
CT31 Low-voltage Thermostat Limited Warranty Honeywell warrants this product to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell's option).
Need Help? For assistance with this product please visit www.honeywell.com/yourhome or call Honeywell Customer Care toll-free at 1-800-468-1502 Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 www.honeywell.com/yourhome Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark.
Guide d’utilisation CT31 Thermostat basse tension Éléments nécessaires à l’installation Assurez-vous que le paquet contient les éléments suivants : Etiquettes de fils Carte de mise en garde Chevilles et vis de montage (2 de chaque) Thermostat CT31 Plaque cache-trous Outillage et matériel nécessaires : • Tournevis • Marteau • Niveau (facultatif) • Crayon • Mèche (3/16” pour cloisons sèches, 7/32” pour cloisons plâtre) ® U.S. Marque déposée. Brevets en instance.
Guide d’utilisation Retirez l’ancien thermostat 1 Coupez le courant au niveau de l’installation de chauffage/de climatisation (ou du panneau de fusibles ou de disjoncteurs). 2. Retirez le boîtier et le thermostat. Laissez la plaque murale et les fils qui y sont fixés. Laissez la plaque de montage en place Le thermostat comporte-t-il un tube scellé contenant du mercure ? Si c’est le cas, reportez-vous à l’avis concernant le mercure ci-dessous.
Thermostat basse tension CT31 Étiquetez les fils et retirez l’ancienne plaque de montage Débranchez les fils un par un à l’aide d’un tournevis. À mesure que vous les débranchez, enveloppez-les avec l’étiquette correspondant à la lettre de votre ancien thermostat. (Des étiquettes adhésives sont fournies dans l'emballage de votre thermostat.) Ne retirez l’ancienne plaque qu’une fois tous les fils étiquetés.Veillez à ne pas laisser des fils détachés tomber dans l’ouverture du mur.
Guide d’utilisation Montez la thermostat 1 Percez des trous aux emplacements repérés au crayon (3/16" pour les cloisons sèches, 7/32” pour le plâtre. 2 Entrez les chevilles dans les trous avec un marteau jusqu’à ce qu’elles soient de niveau avec le mur. 3 [Facultatif] Tirez les fils par la plaque cache-trous (s’il en est besoin pour dissimuler les marques laissées par votre ancien thermostat). 4 Tirez les fils par la base du thermostat et insérez les vis.
Thermostat basse tension CT31 Positionnement du levier de réglage 1 Séparez le couvercle du thermostat et retirez la plaquette en plastique. 2 À l’aide d’un crayon, amenez le levier de réglage à l'emplacement convenant à votre installation (voir le tableau ci-dessous). Votre installation Réglage Chaudière au gaz ou au mazout (de rendement inférieur à 90 %) 0.4 Chaudière électrique (tous types) 0.3 Chaudière à haut rendement (rendement supérieur à 90 %) 0.
Guide d’utilisation Mode d’emploi Réglage de la température Déplacez le levier pour obtenir la température intérieure désirée Commutateur de ventilateur On/March : Le ventilateur fonctionne en permanence Auto : Le ventilateur ne fonctionne que lorsque le chauffage ou la climatisation sont en marche Commutateur de mode de fonctionnement • Cool/Clim : Le thermostat ne régule que la climatisation • Heat/Chauff : Le thermostat ne régule que le chauffage • Off/Arrêt : Le chauffage et la climatisation son
Thermostat basse tension CT31 Garantie limitée Honeywell garantit ce produit contre tout vis de fabrication ou de matière dans des conditions d’utilisation et de service normales, pendant une durée d’un (1) an à compter de la date d’achat par le consommateur. Si à un moment quelconque pendant la durée de la garantie, le produit est jugé défectueux ou tombe en panne, Honeywell le réparera ou le remplacera (au choix d’Honeywell).
Vous faut-il de l’aide ? Pour obtenir de l’assistance concernant ce produit, visitez www.honeywell.com/yourhome ou appelez gratuitement l’assistance client d’Honeywell au 1-800-468-1502 Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 www.honeywell.