Manual
Table Of Contents
- 68-0240E-6
- 68-0240F-6.pdf
- Application
- Caractéristiques
- Fiche technique
- Planification de l’installation
- Application
- Vérifier les exigences relatives à l’installation
- Applications - appareil de refroidissement
- Applications - humidificateur
- Applications - apport d’air extérieur
- Ajout du moniteur W8600F (en option)
- Ajout de l’indicateur AIRWATCHMD W8600A
- Choix de l’emplacement
- Choix de la position d’installation
- Raccords de gaines requis
- Raccords de transition
- Déflecteurs
- Raccords de dérivation
- Installation
- Avant d’installer ce produit…
- Déballer le filtre à air électronique
- Nettoyer le compartiment du ventilateur
- Fixer le boîtier à l’appareil de chauffage
- Installer les déflecteurs
- Fixer le boîtier au système de gaines
- Sceller les joints
- Installer la clavette de la cellule dans la bonne direction.
- Fixer les poignées des cellules
- Réassembler le filtre à air
- Terminer le raccordement
- Fonctionnement
- Vérification
- Maintenance
- Nettoyage des cellules et des préfiltres
- Nettoyage des cellules dans le lave-vaisselle
- Nettoyage des cellules dans un bac
- Nettoyage des cellules dans un lave-auto
- Remise en place des préfiltres et des cellules
- Remplacement des post-filtres à fibres
- Remplacement des fils d’ionisation
- Réduction de l’odeur d’ozone
- Pièces de rechange (Tableau 3)/vue explosée (Fig. 19).
- Pièces et accessoires non illustrés (Tableau 4)
- calendrier de rappel du lavage
F300 ELECTRONIC AIR CLEANER
11 68-0240EF—06
1. Open access door.
2. Remove and retain the two screws from the front of the
power box and the two screws from the sides of the
power box. See Fig. 11.
3. In the power box, remove and retain two wire nuts that
connect the line cord leads to the power box wiring.
4. Remove the power cord green lead from the green
grounding screw on the wiring compartment barrier.
5. Remove the power cord and the strain relief.
6. Install the plug (provided with the literature pack) in the
hole left by the power cord.
7. Attach conduit through a power box side knockout.
8. Wire the air cleaner directly to line voltage using wire
nuts. See Fig. 12. Secure ground connection to the
green ground screw on the wiring compartment barrier.
9. Replace power supply cover and access door.
Fig. 11. Removing cover from power box.
Fig. 12. Conduit connection for electronic air cleaner.
OPERATION
Large particles (lint, hair) are caught by the prefilter. As the
dirty air passes through the intense high voltage electric field
surrounding the ionizer wires, all particles are given an
electrical charge.
The air then moves through the collector part of the cell where
alternate parallel plates are charged positively and negatively,
creating a uniform electrostatic field. The charged particles are
attracted to and collect on the plates that have the opposite
electrical charge.
The air then passes through media postfilters, removing
additional particles from the air stream. The air leaving the air
cleaner has fewer particles. Each time the air circulates
through the electronic air cleaner, more particles are removed.
CHECKOUT
Inspect the Installation
Make sure:
• Turning vanes and transitions, as needed, are correctly
installed.
• Sheet metal joints between air cleaner and furnace are
sealed.
• All sheet metal connections are complete.
• Original furnace filter has been removed and the blower
compartment cleaned.
• If atomizing humidifier is installed upstream from the air
cleaner, a disposable furnace filter is installed between the
humidifier and the air cleaner.
• Outside air, if used, is mixed with return air or heated, as
necessary, before it can reach the air cleaner.
• Airflow arrows on the electronic cell point downstream.
• Metal mesh prefilter is on the upstream side and media
postfilter is on downstream side of the cell.
• Cell handle faces outward.
• Electronic cell and prefilter are clean and dry.
• W8600F wiring connections are correctly made.
M20806
3
1
2
REMOVING COVER
FROM POWER BOX.
ELECTRONIC
AIR CLEANER
WIRING
COMPARTMENT
BLACK
BROWN
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
THE AIR CLEANER CAN BE COMPLETELY ISOLATED FROM
THE ELECTRICAL CIRCUIT OF THE HVAC SYSTEM UNLESS
REQUIRED BY LOCAL CODE TO USE SAME CIRCUIT. ANY
CONVENIENT HOUSE CIRCUIT CAN POWER AIR CLEANER,
REGARDLESS OF ELECTRICAL RATING OF HVAC SYSTEM.
M5707
2
1
2
L1 (HOT)
L2
1