HE360 Humidifier and Installation Kit OWNER’S MANUAL Scan for installation video http://hwll.
HE360 HUMIDIFIER AND INSTALLATION KIT WELCOME To the comfortable world of humidified air. When you use your Honeywell humidifier, notice that your skin is not as dry, and that your scratchy throat and irritated nasal passages that aggravate allergies and asthma are steadily improving. You have also taken the first step in reducing the zapping you create when you walk on your carpet and then touch your TV, computer, metal door knob or your pet.
HE360 HUMIDIFIER AND INSTALLATION KIT Included Accessories Quantity Table 1. Included Accessories. Accessory 20 ft (6.2m) 18 gauge, two-strand thermostat wire 20 ft (6.2m) 1/4 in. (6.35 mm) OD feed water tubing 10 ft (3.1m) 1/2 in (12.
HE360 HUMIDIFIER AND INSTALLATION KIT Determining Best Location for Humidifier CAUTION Temperature and Static Pressure Hazard. Can cause property or equipment damage. Locate humidifier where ambient temperature is between 32°F (0°C) and 160°F (71°C). Do not install humidifier where freezing temperatures could occur. Be sure supply plenum static pressure is no greater than 0.4 in. wc and water pressure is no greater than 124 psi.
HE360 HUMIDIFIER AND INSTALLATION KIT Locating Closest Floor Drain • Select location with access to a floor drain to provide drainage for air conditioner condensation and humidifier drainage. • If you do not have a drain available, we recommend that you install the Honeywell Whole House Drum or Disk Humidifier. Make sure that the 10 ft (3.1m) of drain tubing is adequate to reach from the humidifier drain connection to the floor drain.
HE360 HUMIDIFIER AND INSTALLATION KIT CAUTION Sharp Edges Installation Hazard. Can cause personal injury. Wear gloves and safety glasses. 1. 2. Turn off power to the air handing system at the circuit breaker. Draw a level line on the plenum in the location chosen for the humidifier. (Leveling assures optimal humidifier performance.) 3. Locate the template (form number 69-2641 included in the box). 4. Tape the template in position and trace around the template. 5.
HE360 HUMIDIFIER AND INSTALLATION KIT 8. 9. 10. Make sure the humidifier housing is level, then position it in the opening so the plastic tabs are in place on the upper sheet metal edge of the opening. Use pliers, as necessary, to flatten cut edges. See Fig. 5. Push in securing clips until completely seated. Drill holes and install the three sheet metal screws on the top of the humidifier housing. Secure the housing with the three remaining screws.
HE360 HUMIDIFIER AND INSTALLATION KIT Connecting the Plumbing Use hot or cold water and either hard or softened water in the humidifier. 1. Shut off the water. CAUTION Chemical Hazard. Can cause personal injury or equipment damage. Do not use any line connected to an air conditioner. Do not use gas line. 2. Use the self-piercing saddle valve (included) to tap into the water supply line at the location selected. See Fig. 6. If tapping into galvanized pipe, drain line and pre-drill 3/17 in.
HE360 HUMIDIFIER AND INSTALLATION KIT NOTE: To prevent leaking, use plastic (Delrin) sleeve rings with plastic tubing. Use copper sleeve rings only with copper tubing. d. Insert the tubing into the solenoid valve fitting and support the valve while tightening the compression nut. NOTE: Do not over-tighten the compression nut. Moderate tightness prevents leaking. e. Repeat steps a. through d. for solenoid valve fitting. f. Secure tubing with clamps provided.
HE360 HUMIDIFIER AND INSTALLATION KIT Installing the Pressure Switch IMPORTANT Do not install the switch in an area where temperature exceeds rating of -40 °F to 190 °F (-40 °C to 88 °C). 1. 2. 3. 4. 5. 6. 7. Disconnect power from the humidifier before installing. Mount the switch vertically with pressure connectors facing down, using provided self-tapping screws to secure the switch to the duct. Cut 3/4-in.
HE360 HUMIDIFIER AND INSTALLATION KIT Installing the Humidistat Installing on Mounting Duct 1. Apply the template to the duct location chosen for the humidistat. Make sure the template is level before drilling the holes. 2. Refer to the template (provided with the H8908 Humidistat Installation Instructions) to drill the control assembly opening and mounting holes for the H8908. 3. Remove the H8908 case from the base. 4. Position the foam gasket on the H8908 base. 5.
HE360 HUMIDIFIER AND INSTALLATION KIT WIRING CAUTION Hazardous Voltage. Can cause personal injury or equipment damage. Disconnect power supply before installing or servicing equipment. IMPORTANT — Use THIS wiring diagram—NOT the one supplied with humidistat instructions. — All wiring must comply with applicable local code, ordinances and regulations. Wire the humidifier solenoid valve, pressure switch and humidistat. See Fig. 12.
HE360 HUMIDIFIER AND INSTALLATION KIT TESTING HUMIDIFIER OPERATION Checklist Humidifier is level. Control wiring was reviewed using circuit diagram. Humidifier is plugged in. Feed line has no kinks. Drain line slopes continuously down and ends at floor drain. Water hose inside humidifier is connected to PerfectFlow™ water distribution tray. After installation use the following steps to check the humidifier operation: 1. Turn on the power and the water supply. 2.
HE360 HUMIDIFIER AND INSTALLATION KIT Controlling Your Humidity Settings Your H8908 Humidistat controls your humidifier. • Choose the humidity control setting using the combination of relative humidity/ outdoor temperature setting scale on your humidity control dial. • Match the dial setting to the outdoor temperature to optimize the humidity level while reducing the moisture condensation on your windows. See Table 2 to adjust the humidity control to the recommended setting.
HE360 HUMIDIFIER AND INSTALLATION KIT MAINTAINING YOUR HUMIDIFIER A regular maintenance program prolongs the life of your humidifier and makes your home more comfortable. The frequency of cleaning depends on the condition of your water. You can use either hard or soft water in your humidifier, but hard water mineral deposits are more difficult to clean than soft water deposits. Use the following procedure to clean your Honeywell humidifier. WARNING Serious Personal Injury Hazard.
HE360 HUMIDIFIER AND INSTALLATION KIT FEED TUBE NOZZLE WATER DISTRIBUTION TRAY HUMIDIFIER PAD ASSEMBLY HUMIDIFIER HOUSING COVER ASSEMBLY THUMB SCREW M12809 Fig. 13. Cleaning your humidifier. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Disconnect the drain hose from the drain fitting on the bottom of the humidifier housing. Clean the drain fitting, if necessary. Bend the drain hose to loosen any mineral deposits. Flush the drain hose with pressurized water (a running tap) to clean the hose.
HE360 HUMIDIFIER AND INSTALLATION KIT TROUBLESHOOTING YOUR HUMIDIFIER Problem Water leakage Table 3. Troubleshooting Humidifier. What to look for What to do Leaking joints. Shut off water. Tighten connections. Brass tubing inserts Verify that brass tubing inserts are used. Saddle valve leaking. Verify rubber pad is installed on saddle valve. No water to drain. Electrical Verify control circuit wiring. Check all connections. Humidistat Turn humidistat up and down and listen for contact to click.
HE360 HUMIDIFIER AND INSTALLATION KIT LIMITED ONE-YEAR WARRANTY Honeywell warrants this product, excluding humidifier pad, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time.
HE360 HUMIDIFIER AND INSTALLATION KIT 19 69-2631ES—03
HE360 HUMIDIFIER AND INSTALLATION KIT Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 customer.honeywell.com ® U.S. Registered Trademark © 2013 Honeywell International Inc. 69-2631ES—03 M.S. Rev.
69-2631S_B.fm Page 1 Monday, April 29, 2013 2:27 PM Humidificador HE360 y kit de instalación MANUAL DE INSTRUCCIONES Escanee para ver el video de instalación http://hwll.
69-2631S_B.fm Page 2 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN BIENVENIDO Le damos la bienvenida al mundo confortable del aire humidificado. Cuando utilice su humidificador Honeywell, observará que su piel no estará tan seca, y que la garganta rasposa y los conductos nasales irritados que agravan las alergias y el asma mejorarán continuamente.
69-2631S_B.fm Page 3 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Accesorios incluidos Cantidad Table 1. Accesorios incluidos. Accesorio 20 pies (6.2 m) Cable calibre 18 de dos conductores para termostato 20 pies (6.
69-2631S_B.fm Page 4 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Cómo determinar la mejor ubicación para el humidificador CAUTION Temperatura y peligro de presión estática. Puede dañar la propiedad o el equipo. Ubique el humidificador donde la temperatura ambiente esté entre 32 °F (0 °C) y 160 °F (71 °C). No instale el humidificador donde pudiesen ocurrir temperaturas de congelamiento. Cerciórese de que la presión estática en el plenum no sea mayor de 0.
69-2631S_B.fm Page 5 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Elección de la ubicación del suministro de agua • Utilice agua dura o blanda en el humidificador y agua caliente o fría. El índice de flujo de agua, con el humidificador funcionando, es 3.5 gal./h (13 litros/h) para empapar la almohadilla y proporcionar humedad para la evaporación. • Cerciórese de que los 20 pies (6.
69-2631S_B.fm Page 6 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Instalación del humidificador WARNING Voltaje peligroso Puede causar lesiones personales o daño al equipo. No corte ni taladre en ningún accesorio de aire acondicionado o de electricidad. CAUTION Riesgo de bordes afilados en la instalación. Puede ocasionar lesiones personales. Use guantes y gafas de seguridad. 1. 2. 3. 4. 5. 6.
69-2631S_B.fm Page 7 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN SUJETADOR VISTA SUPERIOR CARCASA DEL HUMIDIFICADOR SUJETADOR MS12813B Fig. 4. Colocación de los sujetadores de fijación. 8. 9. 10. Cerciórese de que la carcasa del humidificador esté a nivel, y seguidamente colóquela en la abertura de modo que las pestañas plásticas queden en su lugar en el borde superior de la lámina metálica de la abertura.
69-2631S_B.fm Page 8 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN 11. Vuelva a instalar el ensamble de la almohadilla del humidificador en la carcasa de este. IMPORTANTE Reconecte el tubo de alimentación de agua y verifique que el tubo no quede pellizcado o torcido. 12. Coloque la cubierta en su lugar y asegure con los tornillos de pulgar ubicados en la parte inferior de la cubierta. Conexión de plomería Utilice agua caliente o fría y dura o blanda en el humidificador. 1.
69-2631S_B.fm Page 9 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN 3. Utilice tubería de 1/4 in (6 mm) de diámetro externo y conecte la válvula de montura al lado de la toma de la válvula del solenoide del humidificador (consulte la Fig. 7). a. Coloque la tuerca de compresión de latón sobre la tubería. b. Coloque el inserto de latón en el extremo de la tubería. c. Coloque el aro de compresión plástico sobre la tubería.
69-2631S_B.fm Page 10 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN 4. Conecte un tubo de drenaje de 1/2 in (13 mm) al acople de drenaje del humidificador y hágalo llegar hasta el drenaje de piso (consulte la Fig. 8). a. Coloque la abrazadera del drenaje sobre la tubería. b. Empuje la tubería sobre la boquilla de drenaje del humidificador. c. Apriete la abrazadera alrededor de la tubería utilizando un alicate/la mano para asegurar el drenaje del humidificador. d.
69-2631S_B.fm Page 11 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN 7. Puede cortar la tubería para adecuar el largo de la conexión entre el codo de acople y el interruptor. También se recomienda fijar la manguera a las estructuras existentes para evitar la desconexión accidental.
69-2631S_B.fm Page 12 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Instalación del humidistato Instalación en el conducto de montaje 1. 2. 3. 4. 5. 6. Aplique la plantilla a la ubicación del conducto elegido para el humidistato. Compruebe que la plantilla esté nivelada antes de perforar los agujeros.
69-2631S_B.fm Page 13 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN IMPORTANTE — Utilice ESTE diagrama de cableado – NO el que se suministra con las instrucciones del humidistato. — Todo el cableado debe cumplir con la normativa, ordenanzas y regulaciones locales pertinentes. Cablee la válvula del solenoide del humidificador, el interruptor de presión y el humidistato. Consulte la Fig. 12. NOTA: Es aceptable cambiar la posición de los cables rojo y blanco cuando cablee el equipo.
69-2631S_B.fm Page 14 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN PRUEBA DE FUNCIONAMIENTO DEL HUMIDIFICADOR Lista de comprobación El humidificador está nivelado. El cableado de los controles ha sido revisado utilizando el diagrama de circuito. El humidificador está enchufado. La tubería de alimentación no tiene torceduras. La tubería de drenaje desciende continuamente y termina en el drenaje de piso.
69-2631S_B.fm Page 15 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Control de la configuración de humedad Su humidistato H8908 controla su humidificador. • Elija la configuración de control de humedad utilizando la combinación de humedad relativa/escala de configuración de temperatura exterior de su selector de control de humedad.
69-2631S_B.fm Page 16 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN WARNING Peligro de lesiones personales graves. Puede causar descarga eléctrica y lesiones provocadas por las piezas en movimiento. Desconecte la electricidad y corte el suministro de agua antes de retirar la cubierta. IMPORTANTE Nunca aceite ninguna pieza del humidificador. Cada 1 o 3 meses (dependiendo de la calidad del agua) 1. 2. 3. 4. 5. 6.
69-2631S_B.fm Page 17 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Desconecte la manguera de drenaje del acople de drenaje en la parte inferior de la carcasa del humidificador. Limpie el acople de drenaje, si fuese necesario. Doble la manguera de drenaje para aflojar los depósitos de minerales. Enjuague la manguera de drenaje con agua presurizada (de un grifo de agua corriente) para limpiar la manguera.
69-2631S_B.fm Page 18 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Table 3. Localización y solución de problemas del humidificador. No hay agua en Electricidad Verifique el cableado del circuito de control. el drenaje. Revise todas las conexiones. Humidistato Gire el humidistato hacia arriba y hacia abajo, y escuche que el contacto haga clic.
69-2631S_B.fm Page 19 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN Table 3. Localización y solución de problemas del humidificador. Humedad baja El soplador del • Reinicie el interruptor de circuito o sistema de verifique si hay algún fusible quemado. calefacción no • Verifique que haya energía en el sistema está funcionando de calefacción. • Revise todas las conexiones del cableado externo. • Revise la configuración del control de humedad.
69-2631S_B.fm Page 20 Monday, April 29, 2013 2:27 PM HUMIDIFICADOR HE360 Y KIT DE INSTALACIÓN GARANTÍA LIMITADA DE UN AÑO Honeywell garantiza por el período de un (1) año a partir de la fecha de compra por parte del consumidor, que este producto, sin incluir la almohadilla del humidificador, no presentará defectos en los materiales ni en la mano de obra, en condiciones normales de uso y de servicio.