Performance Series Full PoE Network Video Recorder HEN04112 HEN04122 HEN04102 HEN08112 HEN08122 HEN08142 HEN08102 HEN16122 HEN16142 HEN16162 HEN16102 Remote User Guide Document 800-21261V3 – Rev A – 05/2016
Remote User Guide
Revisions Issue Date Revisions A 08/2015 New document. (Based on 800-20017) V1 Rev A 10/2015 Added a note in the Configurations section, table 3-2. V2 Rev A 03/2016 Amended the list of NVR models. V3 Rev A 05/2016 Removed any reference to Google Chrome.
Contents | 5 Contents 1 About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Overview of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1 Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparing to Use the Device Web Client . . . . . . . . . . . . . . .
| Performance Series Full Poe Embedded NVR Remote User Guide Configuring PPPoE . . . . . . . . . . . . . . . . Configuring DDNS . . . . . . . . . . . . . . . . Quick DDNS and Client-end Introduction . . . . Configuring the IP Filter. . . . . . . . . . . . . . Configuring Email . . . . . . . . . . . . . . . . . Configuring FTP . . . . . . . . . . . . . . . . . Configuring UPnP. . . . . . . . . . . . . . . . . Configuring SNMP . . . . . . . . . . . . . . . . Multicast. . . . . . . . . . . . . . . . . . . .
Figures | 7 Figures Figure 1-1 1 IE Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 1-2 Controls Installation Popup Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 1-3 Unblocking Security Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 1-4 Web Service Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-16 FTP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Figure 3-17 UPnP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Figure 3-18 SNMP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Figure 3-19 Multicast Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures | 9 Figure 3-61 Default Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Figure 3-62 Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Figure 4-1 Playback Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Figure 4-2 List of Recorded Video Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Figure 4-3 Playing Back Video .
| Performance Series Full Poe Embedded NVR Remote User Guide www.honeywell.
Tables | 11 Tables 1 Table 1-1 PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 1-2 Viewer Configuration Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 2-1 Live View Video Window Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 2-2 Live View Video Window Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 2-3 Image Settings . . .
| Performance Series Full Poe Embedded NVR Remote User Guide www.honeywell.
About This Document This document describes how to access Honeywell’s Performance Series Full PoE Network Video Recorder remotely using a browser-based web client. This document is intended primarily for remote users.
| Performance Series Full Poe Embedded NVR Remote User Guide Related Documents For more information about using the Performance Series Full PoE Network Video Recorder, refer to the following documents: Document title Part number* Performance Series IP Network Video Recorder User Guide 800-21090 Performance Series IP NVR Quick Connection Guide 800-21088 Performance Series IP NVR Quick Network Guide 800-21089 * These part numbers are subject to change.
1 Logging In 1 This chapter includes: • PC requirements for the web client software • Logging in to the web client software • The web client software’s main page Preparing to Use the Device Web Client PC Requirements Table 1-1 PC Requirements Component Minimum Requirement Processor Quad core System memory (RAM) 2G or higher Non-integrated video card 256M or higher Before You Log In Ensure that the following conditions are met: • Ensure that the network connection is good.
| Performance Series Full Poe Embedded NVR Remote User Guide Note Before you uninstall the web control, close all web pages. If you do not, then the uninstallation procedure might result in an error. • The current NVR supports various browsers such as Apple Safari and Mozilla Firefox. The NVR supports multiple-channel monitoring (depending on your model) on an Apple PC. 1. Open a Web browser window. Logging In Note These instructions were created using IE.
Logging In | 17 For example, if your NVR’s IP address is 192.168.1.108, then enter http://192.168.1.108 in the address field. A message pops up asking if you want to install controls. Figure 1-2 3. Controls Installation Popup Message Click Install to install the controls. Note The relevant plug-ins might be blocked by your web browser security settings. See Figure 1-3. Figure 1-3 Unblocking Security Plug-ins When installation is successful, the Web Service login window appears.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 1-4 4. Web Service Login Window Enter your username (default: admin) and password (default: admin), then click Login. Note For security, we recommend that you modify your password on your first log in. LAN Mode The LAN main window is divided into 4 main sections. See Figure 1-5. In LAN mode, you can select different channels and different modes at the bottom of the interface. www.honeywell.
Logging In | 19 Figure 1-5 LAN Mode Main Window 1 2 3 4 Section 1: Function Buttons Figure 1-6 LAN Main Window Function Tabs There are six function tabs: • Preview: You are currently in the Preview (Live) mode, where you can see all these tabs.
| Performance Series Full Poe Embedded NVR Remote User Guide Section 2: Monitor Channels and Function Buttons Figure 1-7 Monitor Channels Section and Function Buttons Monitor Channels The Monitor Channels section displays monitor channels that are successfully connected to the NVR. Left-click to select a channel for viewing, or click Start All. Note The Start All button changes to Open All on the GUI.
Logging In | 21 Figure 1-8 Main Stream and Extra Stream Start Talk Button Figure 1-9 Start Talk Button Enabling Bi-Directional Communication 1. Click to enable bi-directional communication. 2. Click in the control panel on the right to select the bi-directional communication mode. There are four options for the communication mode: DEFAULT, G711a, G711u, and PCM.
| Performance Series Full Poe Embedded NVR Remote User Guide Instant Record Button Figure 1-11 Instant Record Button Click Instant Record, and the button turns blue. The NVR begins manual recording. Click Instant Record again to restore the NVR to the previous recording mode. Local Play Button The NVR can play back saved files (in the.dav format) in the PC. 1. Click Local Play, and an interface appears for selecting the playback file. Figure 1-12 2.
Logging In | 23 Section 4: Viewer Configuration Controls Table 1-2 Button Viewer Configuration Controls Name Description Video Quality Click to select the video quality. Select either High quality or Low quality. Fluency Click to configure the fluency. Select from Fluency Level 1, Fluency Level 2, Fluency Level 3, Middle level, Latency Level 1, Latency Level 2, and Latency Level 3. Full Screen Click to switch the viewer to show video full screen. Click Esc (on your PC) to quit full screen.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 1-13 WAN Mode Interface The Difference Between LAN and WAN • In WAN mode, by default, the NVR system opens the main stream for the first channel and displays it on the monitor. The Open/Close button in the left pane does not work. Note The window display mode and the channel number are assigned by default. For example, for the 16-channel NVR, the maximum window split is 16 screens.
Logging In | 25 Note Because of bandwidth limitations, the NVR system can not support monitoring and playback at the same time. To enhance search speed, the NVR system automatically closes the monitoring or playback interface when you are searching for recorded video in the configuration interface. Logging Out Click the Logout tab in the Main Menu. The NVR returns to the Login interface. Figure 1-14 Login Interface Uninstalling the Web Control You can use the web un-install tool uninstall_web.
| Performance Series Full Poe Embedded NVR Remote User Guide www.honeywell.
2 Live Viewing 2 This chapter includes: • A description of the NVR web client. • Descriptions of image/relay output settings, including image settings. • Descriptions of the Information available for viewing in live view, including system version, log, connection log, and online user information. Live Viewing Left-click a channel name in Section 2, the Monitors Channel section, to select that channel for viewing. The video window shows statistics about the video.
| Performance Series Full Poe Embedded NVR Remote User Guide IP Address Figure 2-1 Live View Video Window Table 2-1 Live View Video Window Controls Digital Zoom Bit Rate Channel Number Stream Table 2-2 Local Record Snapshot Close Window Audio Live View Video Window Controls Control Description Display Device Information Shows the following information about the video: • IP address • Channel number • Bit rate • Stream: Select either M for Main stream or S for sub stream.
Live Viewing | 29 Table 2-2 Live View Video Window Controls Control Description Audio Turn audio On or Off. Note This control has nothing to do with the system audio setup. Close Window Close video in the current window. Image/Relay-out Settings Configuring Image Settings Here you can adjust the selected channel’s brightness, contrast, hue, and saturation. Figure 2-2 Image Settings 1. Click to select one channel’s video.
| Performance Series Full Poe Embedded NVR Remote User Guide Note All of these configurations apply to the Web Viewer only. Information Version 1. Click the arrow next to System to expand the System menu tree. 2. Click Version to open the Version configuration interface. Figure 2-3 Version Configuration Interface Here you can view the recording channel, the alarm input/output information, the software version, and the release date. None of these values can be changed; they are viewable only.
Live Viewing | 31 Figure 2-4 Log Configuration Interface Table 2-4 Log Configurations Configuration Description Start Time Set a start time for the log. End Time Set an end time for the log. Type Select from System Operation, Configuration Operation, Data Operation, Event Operation, Record Operation, User Management, Log Clear, and All. Search Click Search to find a log or logs that fit the search requirements (Begin time, End time, and Type).
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 2-5 Connection Log Interface 2. Set a Start and End Time, select a Channel. 3. Click Search to find the connection log. Online User Click Online User in the System menu to open the Online User interface. Figure 2-6 Online User Configuration Interface You can see what users are currently online. www.honeywell.
3 Configuration 3 This chapter includes descriptions about how to configuring the following: • Camera setup • Network setup • Event settings • Storage • General settings, including the following: • the device’s name and number • the interface language • the video standard • what happens when the HDD is full • the pack duration Setup Configuring the Camera Setup through the Remote Interface If the NVR connects to an IP camera through a private protocol, then the Camera Conditions page d
| Performance Series Full Poe Embedded NVR Remote User Guide Note The NVR automatically defaults to selecting channel 1 when you navigate between configuration interfaces. For example, if you have selected channel 3 on the Video&Audio configuration interface, and then navigate to the Channel Name configuration interface, the NVR defaults to channel 1 in the Channel selection drop-down.
Configuration | 35 Table 3-1 Camera Conditions Setting Description Brightness Adjusts the monitor window brightness. The default setting is 50. The higher the number, the brighter the video. When you select a value, the bright and dark elements of the video are adjusted. Use this function to adjust video brightness when the entire picture is too dark or too bright. Select from 0 to 100. The recommended range is 40 to 60. Note The video might become washed out if you select a high brightness value.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-2 Note Encoding Interface If the NVR fails to retrieve the configuration information for your selected camera/channel, then you should navigate to a different window (such as Snapshot or Overlay), then navigate back to the Encode window. Table 3-2 Encoding Configurations Setting Description Channel Select a channel from the dropdown list Code Stream Type Select from Main Stream, Motion Stream, and Alarm Stream.
Configuration | 37 Table 3-2 Encoding Configurations Setting Description Resolution The NVR system supports various resolutions, which you can select from a dropdown list. Note The selection is different for each NVR series.
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-3 Snapshot Settings Setting Description Channel Select a channel. Mode Select from two modes: Timing (scheduled) and Trigger. Timing: the snapshot is available during the period you specify. Trigger: the snapshot is available only when a motion detection alarm, tampering alarm, or local activation alarm occurs. Image Size Matches the resolution of the main stream. Quality Select from six quality levels.
Configuration | 39 Table 3-4 Video Overlay Configurations Setting Description Cover-Area 1. Select Preview or Monitor. 2. Click Set, then draw a privacy mask on the specified video in preview or on monitor video. The NVR system supports a maximum of four privacy zones. Channel Display Enable this function so that the system overlays channel information in the video window. Use the mouse to drag the channel display into position. You can see the channel on the live WEB video or the playback video.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-6 2. Channel Name Configuration Interface Enter a new channel name, then click Save. Configuring the Network Setup Configuring TCP/IP Click TCP/IP under NETWORK to open the TCP/IP configuration interface. www.honeywell.
Configuration | 41 Figure 3-7 TCP/IP Configuration Interface Table 3-5 TCP/IP Configurations Configuration Description Mode There are two modes: STATIC and DHCP. • The IP address, submask, and gateway is inactive and not configurable when you select the DHCP mode to automatically search for the IP address. • If you select STATIC mode, then you need to manually configure the IP address, submask, and gateway. • If you select DHCP mode, then you can only view the IP address, submask, and gateway.
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-5 TCP/IP Configurations Configuration Description Alternate DNS Enter an alternate DNS IP address. Note For the IPv6 version IP address, the Preferred DNS and Alternate DNS shall be no more the 128 digits. They also can not be left blank. LAN Download Enable this function so that the system can process the downloaded data first. The download speed is 1.5X or 2.0X of the normal speed.
Configuration | 43 Configuring WIFI Note 1. This section applies only to devices with Wifi capability, such as tablet computers, smartphones, and laptop computers. Click Wifi under NETWORK to open the Wifi configuration interface. Figure 3-9 Wifi Configuration Interface 2. Click to enable Wifi. 3. Double-click the name of a wireless device to connect to it. Note Click Refresh to update the list of wireless network information. Configuring 3G Configuring CDMA/GPRS 1.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-10 CDMA/GPRS Configuration Interface Table 3-7 CDMA/GPRS Configurations www.honeywell.com/security Configuration Description WLAN Type Select a 3G network type to distinguish this 3G module from different ISPs. Choose from WCDMA, CDMA1x, for example. APN & Dial No. APN and the Dial No. are important PPPoE parameters. The APN (Access Point Name) and the Dial No.
Configuration | 45 Table 3-7 CDMA/GPRS Configurations Configuration Description Note If the Pulse Interval is 0, then the system does not end the 3G connection after you close the extra stream monitor. Note The Pulse Interval here is for the extra stream only. This field is inactive if you are using a main stream monitor. IP Address Non-configurable. After the NVR connects to the network through CDMA/GPRS, it receives an IP address, which displays here.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-12 PPPoE Configuration Interface 2. Enter the PPPoE User name and Password, which you receive from your Internet Service Provider (ISP). 3. Enable the PPPoE function. 4. Click Save to save the changes. 5. Reboot the device to activate these changes. After rebooting, the device should connect to the Internet through the PPPoE connection. The IP address is found in the WAN from the IP address column.
Configuration | 47 Table 3-8 DDNS Configuration Options Configuration Description Domain Mode The DDNS server port. Domain Name Your self-defined domain name. Email Address Server email address. Honeywell DDNS The Honeywell DDNS function works with a special DDNS server and special Professional Surveillance Software (PSS). Click DDNS under NETWORK to open the DDNS configuration interface.
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-9 DDNS Configurations Parameter Description Test Click the Test button to test the DDNS configuration/network connection. Email Address The Honeywell applied-for DDNS has an expiration date. When that expiration date is reached, the system sends an email prompt to this email address. Note Do not register frequently. You need to wait at least 60 seconds between registration requests.
Configuration | 49 Domain name: There are two modes: Default domain name and customized domain name. Except for the default domain name registration, you can also use a customized domain name. After you have successfully registered a domain name, you can log in using it instead of the device IP. User name: IMPORTANT! Optional. Enter your email address. Do not register frequently. You must wait at least 60 seconds between attempts at logging in. Too many attempts might cause a server crash.
| Performance Series Full Poe Embedded NVR Remote User Guide Configuring Email Click Email under NETWORK to open the Email configuration interface. Figure 3-15 Email Configuration Interface. Table 3-10 Email Configurations www.honeywell.com/security Parameter Description Enable Click to enable the email function. SMTP server Enter the email SMTP server IP. Port Enter the corresponding port. Default is 25. Anonymous Only available if the server supports the anonymity function.
Configuration | 51 Table 3-10 Email Configurations Parameter Description Interval The interval for sending ranges from 0 to 3600 seconds. 0 means that there is no interval. Note The system will not send an email immediately when the alarm occurs. When an alarm, motion detection, or video abnormality triggers an email, the system sends out the email according to the interval that is specified here.
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-11 FTP Configurations Setting Description Server IP Enter the IP address for the server. Port Enter the Port number for the server. Username Enter the user name for logging into the server. Password Enter the password for logging into the server. Anonymous Click to enable/disable anonymously logging into the server.
Configuration | 53 Figure 3-17 2. 3. UPnP Configuration Interface Configure the following settings: Enable Click to enable or disable UPnP. LAN IP Enter the NVR’s IP address from the TCP/IP page. WAN IP Enter the router’s IP address. (Optional) Add, edit, or delete a mapping relationship from the Port Mapping List: Add a mapping relationship: Click Add and then, in the Port Info dialog box, select the Protocol (TCP or UDP), enter the Internal Port and External Port details, and then click OK.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-18 SNMP Configuration Interface Table 3-12 SNMP Configurations Configuration Description SNMP Port The listening port of the proxy program of the NVR. It is a UDP port, not a TCP port. This value ranges from 1 to 65535. The default is 161. Read Community This is a string, and it is a command between the managing processes and the proxy process.
Configuration | 55 Multicast Multicast is a transmission mode for data packets. When there are multiple hosts to receive the same data packets, multiple cast is the best option for reducing the bandwidth and the CPU load. The source host can send out just one data for transit. This function also depends on the relationship of the group member and the router group. 1. Click Multicast under NETWORK to open the Multicast configuration interface. Figure 3-19 Multicast Configuration Interface 2.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-20 Auto Register Configuration Interface 2. Click to enable Auto Registration. 3. Enter a Proxy Server IP, Port, and Sub device ID. 4. Click to enable Auto Registration. 5. Then click Save. Alarm Centre You can connect your alarm platform to the NVR’s Alarm Center to develop alarm functions. When a local alarm occurs, the NVR system can upload alarm signals to the Alarm Centre.
Configuration | 57 HTTPS With these settings, you can ensure that the PC successfully logs in through HTTPS to guarantee communication data security. This reliable and stable technology can secure user information and device safety. Note If you have changed the device’s IP, then you’ll need to implement the server certificate again. Note If this is your first time to use HTTPS on your PC, then you’ll need to download the root certificate. HTTPS Configuration Overview 1.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-23 2. Create Server Certificate Window Enter a Country name, a State, a City, Organization, etc, then click Create. A message appears to confirm that you have succeeded in creating a new server certificate. Figure 3-24 Server Certificate Confirmation Message Downloading a Root Certificate 1. Click Figure 3-25 2. to open a File Download - Security Warning window. File Download Warning Click Open to open the Certificate window.
Configuration | 59 Figure 3-26 3. Click Install Certificate to open the Certificate Import Wizard. Figure 3-27 4. Certificate Window Certificate Import Wizard Click Next to open the Certificate Store window.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-28 Certificate Import Wizard - Certificate Store Window 5. Select a location for the certificate. 6. Click Next to complete the process. A message appears to let you know the process is complete. Figure 3-29 7. Certificate Import Wizard - Completion Message Click Finish, and a security warning pops up. www.honeywell.
Configuration | 61 Figure 3-30 8. Security Warning Click Yes. When the installation is complete, a confirmation message appears. Figure 3-31 Certificate Import - Confirmation Message Viewing and Setting the HTTPS Port Click Connection under Network to open the Connection interface. Figure 3-32 Connection Interface Login Configurations 1. Open the browser, then enter https://xx.xx.xx.xx:port, where xx.xx.xx.xx is your device’s IP or domain name. The port is your HTTPS port.
| Performance Series Full Poe Embedded NVR Remote User Guide Configuring Switch Settings You can change the IP Address, Subnet Mask, and Default Gateway for setting the PoE switch settings. 1. Click Switch under Network to open the Switch interface. Figure 3-33 2. Configure the following settings: Table 3-13 3. Switch Configuration Interface Switch Configurations Configuration Description IP Address Enter a new IP address. Subnet Mask Enter a new subnet mask.
Configuration | 63 Figure 3-34 Motion Detect Configuration Interface 800-21261V3 - A - 05/2016
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-14 WEB - Motion Detection Configurations Configuration Description Enable Click to enable motion detection. Select a channel from the drop-down list. Period Define a period during which motion detection is active. 1. Click Set. The Set configuration interface appears. 2. Select a day of the week from the drop-down menu. Select from a day of the week, Work Day, or Free Day.
Configuration | 65 Table 3-14 WEB - Motion Detection Configurations Configuration Description Region 1. Select a motion detection type. 2. Click Set. The Motion Detection Set configuration interface appears. 3. Select the event detection area by left-clicking and dragging the mouse. There are 396 (PAL) or 330 (NTSC) small zones. Green: Indicates the current cursor position. Grey: Indicates the event detection zone. Black: Indicates a disarmed zone. 4. Select a Sensitivity, from 1 to 100.
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-14 WEB - Motion Detection Configurations Configuration Description PTZ Activation When PTZ activation is configured, the system can activate PTZ operation when an alarm is detected. 1. Click Setup to open the PTZ Activation configuration interface. 2. Select a preset, tour, or pattern from the drop-down menu. 3. Click Save. Tour Click to enable a tour to be triggered by an alarm. The system supports 1/8-window tour.
Configuration | 67 Note Video loss does not support anti-dither, sensitivity, or region setup. Click Video Loss under DETECT to open the Video Loss configuration interface. Figure 3-35 Video Loss Configuration Interface The configuration for Video Loss Detection is very similar to the configuration for Motion Detection. Please see Motion Detection Configurations on page 62 for more information.
| Performance Series Full Poe Embedded NVR Remote User Guide The configuration for Camera Tampering Detection is very similar to the configuration for Motion Detection. Please see Motion Detection Configurations on page 62 for more information. Configuring Alarms Before alarm operation, you should check that you have properly connected all alarm devices, such as buzzers and flashing lights. Configuring Local Alarms Click ALARM under EVENT to open the Local Alarm configuration interface.
Configuration | 69 00Configuring Net Alarms Table 3-15 WEB - Alarm Configurations Configuration Description Enable Click to enable alarms. Select a channel from the drop-down list. Period Define a period during which the alarm is active. 1. Click Set. The Set configuration interface appears. 2. Select a day of the week from the drop-down menu. Select from a day of the week, Work Day, or Free Day.
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-15 WEB - Alarm Configurations Configuration Description PTZ Activation When PTZ activation is configured, the system can activate PTZ operation when an alarm is detected. 1. Click Setup to open the PTZ Activation configuration interface. 2. Select a preset, tour, or pattern from the drop-down menu. 3. Click Save. Tour Click to enable a tour to be triggered by an alarm. The system supports 1/8-window tour.
Configuration | 71 Figure 3-38 WEB - Net Alarm Configuration Interface Configuring Alarm Outputs 1. Click Alarm Output under SETTING to open the Alarm Output configuration interface. Figure 3-39 WEB - Alarm Output Configuration Interface 2. Click to enable the alarm output for each alarm. Select from Schedule, Manual, or Stop, and Status. 3. Click Save to save these settings and return to the previous menu.
| Performance Series Full Poe Embedded NVR Remote User Guide There are six types of abnormalities: • No Disk • Disk Error • No Space • Net Disconnection • IP Conflict • MAC Conflict You can configure how the system responds to each kind of abnormality. The configuration is similar for each type. Figure 3-41 www.honeywell.
Configuration | 73 Table 3-16 Configuring for Abnormalities Configuration Description Event Type Select from No Disk, Disk Error, Disk No Space, Net Disconnection, IP Conflict, and MAC Conflict. Less Than: (For No Space configuration only) Configure the minimum percentage of free space on the disk. An alarm lets you know when the disk capacity is low. You need to click to enable this function. Enable Click to enable this function. Alarm Out Select the device output port, 1 or 2.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-42 Schedule Configuration Interface The schedules are color-coded by type: • Green: General recording/snapshot. • Yellow: Motion detection recording/snapshot. • Red: Alarm recording/snapshot. • Blue: MD&Alarm recording/snapshot. Table 3-17 Scheduled Storage Settings Setting Description Channel Select a channel from the drop-down list Pre-record Enter a pre-recording time here. Select from 0 to 30.
Configuration | 75 Table 3-17 Scheduled Storage Settings Setting Description Setup (Sunday to Saturday) Click Setup, then set a recording period. See step 2 below. Setup (Holiday) Click Setup, then set a recording period. See step 2 below. You can configure up to six periods in one day. If you do not click a day at the bottom of the Setup interface, then the changes you make are for today. You can configure up to six periods in one day.
| Performance Series Full Poe Embedded NVR Remote User Guide 3. Configure the schedule, then click Save. Table 3-18 4. Schedule Configurations Configuration Description Channel Select a channel from the drop-down list. Regular Check to enable the Regular schedule mode. Motion Check to enable the Motion Detection schedule mode. Alarm Check to enable the Alarm mode. MD&Alarm Check to enable the MD&Alarm mode.
Configuration | 77 Figure 3-45 Manual Recording Storage Interface Table 3-19 Recording Storage Interface Setting Description Channel See the channel numbers, including the maximum number of channels. Auto Select Schedule, and the system enables the automatic recording function as you set it in the Recording Schedule Setup: General, Motion Detection, or Alarm. See Configuring Storage Schedules on page 73. Manual This is the highest priority.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-46 Table 3-20 General Settings Interface General Settings Configurations Configuration Description Device Name Enter a device name. Device No. Enter a channel number. Language Select a GUI language from the drop-down list. Note You need to reboot the device/NVR to activate this change. Video Standard Select the video standard, either NTSC or PAL. HDD Full Select what happens when the NVR’s storage is full.
Configuration | 79 Figure 3-47 Date & Time Configuration Interface Table 3-21 Date & Time Configurations Configuration Description Date Format Select the date format from the drop-down list. Time Format Select from either 24 hour or 12 hour. Date Separator Select from a period (.), a hyphen (-), or a slash (/). System Time Set the NVR’s time. You have to Save to activate this setting. Sync PC Click to synchronize your NVR’s time with your PC’s time.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 3-48 2. Holiday Settings Configuration Interface Click Add New Holiday to add a holiday, enter the holiday details, then click Save. Configuring Display Settings Display/GUI Settings Click Display under SETTING interface to open the Display/GUI settings configuration interface.
Configuration | 81 Table 3-22 GUI Configurations Configuration Description Image Enhance Check to enable Image Enhance, to optimize the preview video. Auto Logout Enter the how long the NVR waits before automatically logging the user out. Startup Wizard Click to enable the Startup Wizard on restarting or starting up the NVR. Navigation Bar Click to enable/disable the navigation bar. Original Scale Click Set to select to show channels in their original aspect ratio.
| Performance Series Full Poe Embedded NVR Remote User Guide Table 3-23 Display Tour Settings Setting Description Window Split Set the window mode and channel group. Depending on your NVR, it can support up to a 1/4/8/9/16-window split. Channel Group Add channels to a channel group, and when the NVR starts a tour, the tour starts only on the selected channels for the group. Motion Tour/Alarm Tour Set the Motion Detection Tour and Alarm Detection Tour Type window modes.
Configuration | 83 Click PAN/TILT/ZOOM under SETTING to open the PAN/TILT/ZOOM configuration interface Figure 3-52 PAN/TILT/ZOOM Configuration Interface Table 3-25 PAN/TILT/ZOOM Configuration Interface Setting Description Channel Select a channel. PTZ Type Select Remote for the PTZ type. A remotely connected IP camera is connected through the network. Accounts Some Basic User and Group Rules • You can use up to 6 characters for user names and group names.
| Performance Series Full Poe Embedded NVR Remote User Guide User Name Figure 3-53 User Name Account Configurations There are two default users: • admin • a hidden user The hidden default user is for internal use only, and can not be deleted. If users log in without selecting a login user, the hidden default user is automatically used. You can configure some rights for the default hidden user, such as monitor rights so that the user can view channels without logging in.
Configuration | 85 Figure 3-54 Add User Configuration Interface 2. Enter a Username and a Password. Re-enter the Password to confirm it. 3. Select a Group. 4. Select System, Playback, and Real-Time Monitor privileges. 5. Click Save to save these new settings. Modifying a User 1. Click under Modify to open the Modify User configuration interface.
| Performance Series Full Poe Embedded NVR Remote User Guide 2. Change the settings, then click Save. Modifying a Password 1. Click Modify Password in the Modify User configuration interface. 2. Enter the old Password, then enter the new Password twice. 3. Click OK to save the new password. Note Passwords can have up to 6 characters, numbers only. Users with admin rights can modify the password of other users.
Configuration | 87 2. Enter a Group name. 3. Select System, Playback, and Real-time Monitor privileges. 4. Click Save to save these new settings. Modifying a Group 1. Click under Modify to open the Modify Group configuration interface. Figure 3-58 2. Modify Group Configuration Interface Modify the Group privileges, then click Save to save the changes. Automatic Maintenance 1. Click Auto Maintain under SETTING to open the Auto Maintain configuration interface.
| Performance Series Full Poe Embedded NVR Remote User Guide 2. Select when the NVR automatically reboots, both day and time. 3. Select when the NVR automatically deletes old files. 4. Click Save to save the new settings. Note Click Manual Reboot to manually reboot the NVR. Import/Export Click Config Backup under SETTING to open the Import/Export configuration interface.
Configuration | 89 2. Click to select, or select All, then click Default. Upgrade Click Upgrade under SETTING to open the Upgrade configuration interface. Figure 3-62 Upgrade Interface 1. Click Browse, then click to select the upgrade file. 2. Click Upgrade to begin the update. The file name will end with .bin. Note During the upgrade process, do not unplug the power cable, network cable, or shut down the device. CAUTION An improper upgrade program could result in a device malfunction.
| Performance Series Full Poe Embedded NVR Remote User Guide www.honeywell.
4 Playback 4 This chapter includes descriptions of the following: • Playing back recorded video • Downloading recorded video 1. Click the Playback tab at the top of the Main window. Playback The Playback interface appears.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 4-1 Playback Interface 2. Select a recording type, recording date, window display mode, and channel name to select video for playback. 3. Click File List, and the system displays a list of recorded video clips that match the search criteria from step 2. Figure 4-2 List of Recorded Video Clips Video clips www.honeywell.
Playback | 93 4. Select a file from this list for playback, then click Play (). You can play back in full screen mode. Use the playback control bar to control playback. Figure 4-3 Playing Back Video Playback control bar Note For one-channel playback, the system can not play back and download at the same time. Downloading Video After generating a list of recorded video clips by clicking File List, select the files you want to download, then click Download.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 4-4 Downloading Recorded Video The Download button becomes the Stop button, and it indicates the downloading progress (in a percentage). Go to your default Saved Path file to view the downloaded files. See Configuring the Save Path on page 39. Loading More Click www.honeywell.com/security More in Fig 13-94, and the Download by File/Download by Time interfaces appear.
Playback | 95 Figure 4-5 Download by File/Download by Time Interfaces In this window, you can search for recordings or snapshots. Select the channel, recording type, and the recording time.
| Performance Series Full Poe Embedded NVR Remote User Guide www.honeywell.
5 Alarms 5 This chapter describes how to remotely activate the alarms. Activating Alarms Click the Alarm tab at the top of the Main window. The Alarm configuration interface appears. Note For information about configuring alarms, refer to the User Guide.
| Performance Series Full Poe Embedded NVR Remote User Guide Figure 5-1 Alarm Configuration Interface Table 5-1 Alarm Configurations Configuration Type Configuration Alarm Type Operation Alarm Sound www.honeywell.com/security Description Motion Detect Click to enable Motion Detection. The system will then trigger an alarm when motion is detected under the specified circumstances. Video Masking Click to enable Video Masking. The system triggers an alarm when camera masking occurs.
Alarms | 99 You can use the webpage un-install tool uninstall_web.bat to uninstall the web control plugin. Note Before uninstalling the Web control, close all web pages. If you do not, then you might experience an error.
| Performance Series Full Poe Embedded NVR Remote User Guide www.honeywell.
| 1 Index Numerics 3G configurations WLAN type 44 A adding groups 86 users 84 adjusting monitor brightness 29 monitor contrast 29 monitor saturation 29 alarm out motion detection 65, 69 alarms abnormalities 73 configuring sound file 98 disk error 98 disk full 98 enable sound 98 errors 73 external alarms 98 motion detection 98 no signal 98 video loss 98 video masking 98 APN 44 attachments, email 50 audio On/Off, live video 29 authorization 44 B backup 31 bi-directional communication 21 bit rate live video
2 | Performance Series Full Poe Embedded NVR Remote User Guide error latch 73 error message 73 HTTP port 42 latch 65, 69 maximum network connection 42 MD&Alarm schedule 76 messages 66, 70 monitor hue 29 motion detection alarm out 65, 69 motion detection buzzer 66, 70 motion detection emails 66, 70 motion detection latch 65, 69 motion detection message 66, 70 motion detection period 64, 69 motion detection PTZ activation 66, 70 motion detection recording channel 65, 69 motion detection region 65 motion dete
| 3 test 51 title 50 user name 50 email address DDNS 47 emails abnormality 73 error 73 motion detection 66, 70 enabling alarm disk error 98 alarm disk full 98 alarm sound 98 alarm video masking 98 alarms video loss 98 external alarms 98 health email 51 motion detection 98 no signal alarm 98 prompt 98 encryption 50 end time, log 31 error disk 72 internet disconnection 72 IP conflict 72 MAC conflict 72 net disconnection 72 no disk 72 no space 72 event operation 31 event type no disk 73 F file list 93 video
4 | Performance Series Full Poe Embedded NVR Remote User Guide event operation 31 record operation 31 search 31 system operation 31 type 31 user management 31 M MAC address conflict error 72, 73 maximum network connections default 42 MD&alarm 74 messages abnormality 73 error 73 motion detection 66, 70 modifying groups 87 passwords 86 users 85 monitor brightness 29 channels 20 contrast 29 hue 29 saturation 29 motion detection alarm out 65, 69 buzzer 66, 70 emails 66, 70 enabling 98 latch settings 65, 69 me
| 5 S saturation 29 save path default 94 schedules alarm 76 MD&Alarm 76 motion detection 76 search log 31 server IP 46 DDNS 47 single-channel window 23 SMTP 50 snapshot live video 28 motion detection settings 66, 70 SNMP default port 54 default read community setting 54 port settings 54 read community 54 trap address 54 trap port 54 version 54 write community 54 write community default 54 start talking button 21 storage blue 74 channel 76 green 74 red 74 yellow 74 system operation 31 time 79 T TCP port de
6 | Performance Series Full Poe Embedded NVR Remote User Guide www.honeywell.
Honeywell Security Products Americas (Head Office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA www.honeywell.com/security +1 800 323 4576 Honeywell Security Northern Europe Ampèrestraat 41 1446 TR Purmerend, The Netherlands www.honeywell.com/security/nl +31 (0) 299 410 200 Honeywell Security Europe/South Africa Aston Fields Road, Whitehouse Industrial Estate Runcorn, WA7 3DL, United Kingdom www.honeywell.
